Leopard Graphics Update install problem

I've installed 10.5.2 fine, but when I attempt to install the graphics update and restart, it gives me the error "the installer could not install some files in "/". Contact the software provider" I've also tried the combo install, but that gives me the same error. anybody know what's going on here?

Unless you are having problems, I wouldn't worry about it too much. There may be some problems with your setup, and I'm sure an 'erase & install' would cure it - though you might consider this a bit extreme at the moment.

Similar Messages

Display problems after installing 10.5.2 and the leopard graphics update

Shortly after installing the leopard graphics update, my display started exhibiting problems.
The next day, the powerbook wouldn't even boot, just leaving me at a blue screen.
I tried verifying permissions and verifying disk, reinstalling leopard and eventually did a fresh install of Tiger, which boots, but crashes frequently and has graphics corruption as visible in this screenshot:
http://pics.livejournal.com/dorukai/pic/000fw0hw
The same corruption is visible on a second monitor if I connect one.
The timing (being right after installing the graphics update) suggests that the update somehow caused this problem (flashing the video card firmware maybe?) but any ideas at all are very welcome at this point!
Unfortunately after installing Tiger I kept getting updates, and one has broken the ability to boot normally, I can only boot in safe mode

I have the same problem. It happened right after I installed the graphics update. When the computer restarted, my screen went crazy. I couldn't see anything, just a screen full of horizontal lines. After restarting a couple of times it seemed to go away, but it has begun to happen again recently. although not as bad yet. I am not saying it's not a logic board issue, but it does seem funny that more than one person is experiencing the same type of problem after the graphics update. I guess it's time to take a trip to the apple store.

Snow Leopard Graphics Update refuses to Install

I'm using Mac OS X 10.6.4
And the Snow Leopard Graphics Update won't install, and reports:
"Snow Leopard Graphics Update can't be installed on this disk. This update requires Mac OS X 10.6.4."
So far I've tried...rebooting and disk verify, and would welcome any other suggestions.
Thanks!

Hi and welcome to Discussions,
the Snow Leopard Graphics Update was released before your 2010 Mac Pro was released so chance are very good that the Graphics Update is already incorporated in the Snow Leopard version you have on the Mac Pro.
Plus the 2010 Mac Pros are not mentioned in the "Products Affected" list of the Graphics Update http://support.apple.com/kb/HT4286
So, in short you don't need this update.
Regards
Stefan

Leopard Graphics Update won't install

Software Update updated my PowerMac (dual 1.8 G5) to 10.5.2, then I got the alert for iLife 08 and Leopard Graphics Update. The latter install has failed twice with the following message:
*The update "Leopard Graphics Update" can't be installed*
The installer could not validate the contents of the 'LeopardGraphicsUpdate1.0' package. Contact the software manufacturer for assistance.
OK, Apple, ***?
--Chris

Manually download the update and give it another go.

Leopard graphic update

I downloaded and installed the recommended Leopard graphic update, and now certain type on websites appears blurry. I've had this problem before, but fixed it by changing the font smoothing style and text sharpening, however, now no matter what changes I make, the problem persists. Is there anything else I can do? For all intents and purposes major sites like CNN's breaking news banner reads like I'm wearing coke-bottle glasses, and working with larger non-standard type in Pages is giving me a headache. Any advice welcome.

It's actually what I do all the times. When I say that I start in 'closed lid' mode I intend that I open the lid to press the start button and immediately close the lid. In this particular case the Apple Cinema Display remains inactive and after a short while the apple on the lid of my Macbook Pro turns lit and when I open the screen has a black multi language alert which advise me to restart my machine by pressing the start button. After I restart the my Mac in 'open lid' mode and after I log in, appears a message that tells me that the system was restarted after crash and here comes the detailed error that follows:
Thu Feb 21 09:54:28 2008
panic(cpu 1 caller 0x001A8C8A): Kernel trap at 0x00d76e3f, type 14=page fault, registers:
CR0: 0x80010033, CR2: 0x00000000, CR3: 0x01425000, CR4: 0x00000660
EAX: 0x00000000, EBX: 0x00000000, ECX: 0x00000000, EDX: 0x00000000
CR2: 0x00000000, EBP: 0x3f25b8a8, ESI: 0x000002d0, EDI: 0x3f25b880
EFL: 0x00010287, EIP: 0x00d76e3f, CS: 0x00000008, DS: 0x04e00010
Error code: 0x00000002
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x3f25b668 : 0x12b0e1 (0x457024 0x3f25b69c 0x13321a 0x0)
0x3f25b6b8 : 0x1a8c8a (0x460550 0xd76e3f 0xe 0x45fd00)
0x3f25b798 : 0x19eb67 (0x3f25b7b0 0x4e5ac80 0x3f25b8a8 0xd76e3f)
0x3f25b7a8 : 0xd76e3f (0xe 0x24220048 0x10 0xbb0010)
0x3f25b8a8 : 0xd5d042 (0x3f25bb04 0x0 0x3f25b8e8 0x3f11ed)
0x3f25b9a8 : 0xbc4472 (0x2422d000 0x3f25ba80 0x3f25ba80 0x84)
0x3f25ba08 : 0xbbb65e (0x44a4c00 0x3f25ba80 0x3f25ba80 0x84)
0x3f25bb38 : 0xbbcd74 (0x44a4c00 0xbc0358 0x3f25bbec 0x4)
0x3f25bc08 : 0xba8133 (0x44a4c00 0x1 0x0 0x0)
0x3f25bc68 : 0xba193a (0x44a4c00 0x5 0x5 0x44a4c00)
0x3f25bc98 : 0x40db95 (0x44a4c00 0x4646ba8 0x4646ba8 0x0)
0x3f25bce8 : 0x438d33 (0x44a4c00 0x4646ba8 0x4646ba8 0x0)
0x3f25bd48 : 0x18cefa (0x44a4c00 0x4646ba8 0x0 0x0)
0x3f25bdb8 : 0x12d165 (0x4b5d078 0x4264b90 0x3f25bdf8 0x11ee04)
0x3f25bdf8 : 0x126247 (0x4b5d000 0x41591f8 0x4636708 0x0)
0x3f25bf08 : 0x19714c (0x3f25bf44 0x0 0x0 0x0)
Backtrace continues...
Kernel loadable modules in backtrace (with dependencies):
com.apple.NVDAResman(5.1.6)@0xbc3000->0xdeffff
dependency: com.apple.iokit.IONDRVSupport(1.5)@0xbb5000
dependency: com.apple.iokit.IOPCIFamily(2.4.1)@0x6ad000
dependency: com.apple.iokit.IOGraphicsFamily(1.5.1)@0xb99000
com.apple.iokit.IONDRVSupport(1.5)@0xbb5000->0xbc2fff
dependency: com.apple.iokit.IOPCIFamily(2.4.1)@0x6ad000
dependency: com.apple.iokit.IOGraphicsFamily(1.5.1)@0xb99000
com.apple.iokit.IOGraphicsFamily(1.5.1)@0xb99000->0xbb4fff
dependency: com.apple.iokit.IOPCIFamily(2.4.1)@0x6ad000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
9C31
Kernel version:
Darwin Kernel Version 9.2.0: Tue Feb 5 16:13:22 PST 2008; root:xnu-1228.3.13~1/RELEASE_I386
System model name: MacBookPro3,1 (Mac-F4238BC8)
I hope that Apple will fix this issue as soon as possible.
There is one more thing: as I told before, I thought that the culprit was the graphic update 1,0 but today I have the same problem without it.
Help needed! Thank you.

MetaX is suddenly Failing after Snow Leopard Graphics Update?

Is anyone else experiencing any problems with MetaX (http://www.kerstetter.net/index.php/projects/software/metax) causing movies in iTunes to no longer play? I have been using that software extensively previously but since installing the last few updates (Snow Leopard Graphics Update?) everytime I use MetaX to set the tags on my video files it causes them to display a black screen with no audio.

Thanks amop. I was having the same problem intermitently and this worked a treat.
Cheers....

10.5.2 update and Leopard Graphics update = no sleep mode

All, After updating my MacBook Pro to 10.5.2 and the Leopard Graphics update, my computer will not longer enter sleep mode after a specified time. I can manually set the computer to sleep mode, but it will not automatically go to sleep mode. I have tried resetting the System Management Control Center VIA http://docs.info.apple.com/article.html?artnum=303319 and everything else in that doc.
Any suggestions?
TIA Jon

Call AppleCare and see if they can help.
Regular trouble shooting
1) Create a new account, name it test or something
2) log into that account to see if the behavior changes
3) If it does, then there is some problem in your own account.
4) If it doesn't, restart.
5) If the behavior still doesn't change, there is some system configuration error
In this case
6) Open Disk Utility. Verify your disk, then repair permissions (not likely to fix the problem but will at least eliminate that possibilty)
7) Get a copy of Leopard Cache Cleaner and do a MODERATE cache cleaning
8) Restart
If still not fixed, reset PRAM and the SMU. Look on the Apple web site for instructions for your particular computer.
If still not different, do an Archive and Install. However go to the Apple web site and download the 10.5.2 Combo updater first. After you Archive and Install from either the disk that came with your computer (assuming that it is Leopard) or the retail Leopard installer. Then run the combo updater. Then run Software Update.
These problems are disturbing and really shouldn't happen, but they do. However, they can be fixed and you'll find that Mac OS is, overall, much better than the alternatives.
BTW, I just went through this whole mess for crashes on wake from sleep (USB issues) and failure to sleep (printer driver issue). Another computer had DHCP problems and actually needed a reinstall. However both of them are working fine now even though it was a pain getting there.
- gws
Message was edited by: GW Schreyer

Leopard Graphics Update

Has anyone noticed an improvement in gaming on the Santa Rosa Macbook? Specifically, I was wondering if frame rates on WOW have improved.
David

Danielle Lum1 wrote:
Trying to install the Leopard Graphics Update (via Software Update).
When I do, it gives me the following error:
The update "Leopard Graphics Update" can't be saved
You do not have the appropriate access privileges
The Installer package has been moved to the Trash
To try again, open the package from the Finder
I am the only user/administrator for this computer. It is not connected to a network, nor does it have any enabled sharing.
I just loaded up all the other updates from today (I think Garage Band, Keyboard Firmware, etc.) without problem or error message.
So here's my question: Is this update worth the aggravation of trying to figure out how to install it? If it is, what steps should I take to get it onto my system?
It's worth fixing only because it is a symptom of something else that is wrong. It's little things like this that should not be ignored because they may portend a larger issue.
I would first run DU and check the HD and also permissions verify/repair, if necessary.
You should also create another user account temporarily, with full admin privileges and see if you can install the Update via that user. If you can, then there is something wrong with your present admin account that must be fixed.
If not, then you have to proceed further, looking at the system logs, console, etc., for what it causing the problem.
It's important in keeping an OS running perfectly, never to go past an issue without resolving it.
This is often why upgrades or updates fail in the first place.
Thanks!

Snow Leopard Graphics Update question...

How do you know if you have the Snow Leopard Graphics Update is installed on your Mac? Can one check in system profiler? Is that I went from 10.6.3 to 10.6.4 via software update, and then when I ran Software Update in 10.6.4, it only showed the Mac OS X 10.6.5 Update rather than the Snow Leopard Graphics Update and the security update as supposed to, I was hoping that when I installed the OSX 10.6.5 update it also instlled the Snow Leopard Graphics update and all the Security Updates issued in 10.6.4 run.
Thank you for your assistance in this matter.

I was hoping that when I installed the OSX 10.6.5 update it also instlled the Snow Leopard Graphics update and all the Security Updates issued in 10.6.4 run.
It did.
(55336)

Battlefield 2142 plaing SLOW after latest Leopard graphics update

I love using my MacBook Pro to play Battlefield 2142... but ever since I updated the software (which included a Leopard graphics update) the graphics are choppy, the play is stalling and generally slow.
What gives? It was working great before the update!?

I had the same problem with 5.3 and went back to 5.2 in order to play vid games. I saw 5.4 and thought befor I tried it Id call apple tech support to see what the deal is. I didnt get a straight answer. I am going to wait on the game manufactures to see if an update is planned. other wise I may have to get a microsoft dedicated machine for all my vid games. and it doesnt make sence to have to purchase 2 laptops.

Problems with Snow Leopard Graphics Update

I downloaded the new graphics update for Snow Leopard, but when I go to install it it says I need at least a version 10.6.4 OS to use it. I double checked my OS, and that is exactly what I have. What's the problem?

Well I found out what was going on in another thread, apparently my computer already has it incorporated in it, just Steam doesn't recognize that.
Link to the other thread:http://discussions.apple.com/thread.jspa?messageID=12496982

Problems After Snow Leopard Graphics Update 1.0

Hi Mac Users,
I recognised some problems with graphic on Mc OS X 10.6.4 after software update SL Graphics Update 1.0 for example:
- expose extra blue square for window of the application,
- iPhoto photo preview frame became transparent grey and it comes above not only iPhoto windows but all behind,
- problems with Safari
- problems with expose with all window of one application
- others.
To fix it go please to website appletoolbox.com (topic as subject of this thread) or simple search for it by the subject of this thread in web search engine like Google for example.
Simply try:
Reset SMS - http://support.apple.com/kb/HT3964
Also instructions and link on mention website.
or
Safe Boot of Mac OS X - press and hold Shift button after turning on Mac.
Good luck and hopefully Apple will not make more extra problematic updates for us Users
PS. I check that there is no problem on MacBook Pro 2008 edition with this update.
MacJU

mine isnt going nuts but the display wont come back on after waking from sleep (each time and has been replicable since update installed). so i turned it off from sleeping (the computer) but the display sleeps and that also wont come back on when moving the mouse or pressing any keys. only way to get screen back up is performing a cold boot which kinda *****.
ive tried clearing pram but that didnt help. im not sure whats in the graphics update but the next time i reinstall os, i might just skip this update because its causing me more issues than it supposedly solves (im not a big gamer anyway)
this occurs on a mbp 7,1 (13" early 2010). i have not seen or heard it happen on a mbp 5,4 nor have i tried it on my mbp 6,2 (15" early 2010), but even then the screen on my mbp 6,2 has been going nuts before the update (im guessing a faulty card?) but i use my mbp 7,1 for main development work.
i hope apple solves this issue soon

Snow Leopard Graphics Update 1.0 will not install

I have tried 3 times to install the new snow leopard graphics 1.0 each time it says an "error" has occurred. i even tried downloading it from macupdate.com and installing it that way. But either way it says it cannot expand files.
Help Please!
Message was edited by: jdanza

my apologies. i put in the snow leopard disk and it began with the install. (assuming pushing install also constitutes a re-install/repair) after 30 minutes or so. it said the install would continue after a restart. It then boot from the disk. The problem was that when is asked which disk to install on Macintosh HD or my Bootcamp partition and i said Macintosh HD it would inform me after 5 seconds that the the contents could not be modified and that snow leopard would not be installed.
And if you mean repair disk as in run disk utility from the disk, for some reason i could only verify disk, the repair option was grayed out.

Leopard Graphics 1.0 Problem

After installing Leopard Graphics 1.0, I ceased to be able to play DVDs. A DVD is recognized but the player won't start and I just get the color wheel spinning and the system freezing. To correct I reinstalled Leopard, but I was wondering what I need to do to get the graphics upgrade without sacrifice use of my DVD drive!
Suggestions?

I had the same problem with my computer a couple of weeks ago. I actually brought it to the Mac Store and to a genius representative. He basically told me that the Graphics Update 1.0 software is not compatible with the display driver that is inside anything before G5. I have a G5 Imac and have not had this problem after doing the update. In the end I discovered that the only way to fix this problem was to either do an archive reinstall of the OS 10.5 or do a fresh reformat and reinstall the OS operating system of course backing up everything.
I went home backed up all of my files and did a fresh erase and reinstalled the OS 10.5 software. When prompted to reinstall all of the updates I selected everyone except the Graphic Update 1.0. This fixed my problem with the DVD Player program and the freezing of my system. I am surprised that Apple has not removed this download for the Powerbook G4's. This should fix your problem. Let me know if you run into any other problems.

10.5.2 and Graphic Updated No Problems at all

I decide to updated today! i did repair permission before and after both updates and so far i have no Problems with Any Adobe CS3, etc apps... I dont use Time Machine so i dont know if there is a Pro with that... but the rest as apps.. syncing, new features, everything works ok.
I dont have any issues now, but if i do.. i'll let you guys know...
so Far the updated did better than fine..
*i printed some pages and went fine.. (wireless Printer)
*Airport its on (working)
*Leopard does not run slow...
*Folder (stacks) work
*Transparency and not transparency bar work..
*Mouse wakes up computer
-keyboard does not wake up computer,,, only 1 key but i pressed it randomly
Hope i'm not the only one who has no Pros with 10.5.2 !!
Message was edited by: HanselJr

I updated 10.5.2 yesterday. I used the combo updater. It took me 10 minutes. I then downloaded the graphics update, also with no problems. Everything is working just fine. In fact everything seems a little quicker. I use mainly PS CS3, Lightroom and Aperture. All work exceptionally well. I didn't repair permissions because my system is only 2 weeks old. I just went for it!! It worked for me!!!
Good luck to all!

Leopard Graphics Update install problem

Similar Messages

Maybe you are looking for