Leopard installation problems (DVD ejecting)

Two weeks ago I decided not to buy a new Mac but to upgrade my current one. So I've added memory, an extra screen (in an old iMac housing) en an extra HDD. I also wanted to upgrade to OSX 10.5 and iLife '09. To upgrade all the Macs I ordered a family pack with OSX 10.5, iLife '09 and iWork '09.
When I try to install Leopard my DVD is ejected and than I get a grey screen with a folder with the finder symbol and a folder with a questionmark:
[img]http://i172.photobucket.com/albums/w35/sjon_1/P1040780.jpg[/img]
[img]http://i172.photobucket.com/albums/w35/sjon_1/P1040779.jpg[/img]
Does someone know how to solve this?

What it can hold & what it recognizes are two different things, which is why I asked what System Profiler says about the installed memory.
From your Photo Bucket shot, it is obvious that you have used a hack to run the second monitor in the unsupported non-mirror mode. This may or may not have something to do with your problem, as the hack modifies things that remain in place even when the second monitor is not connected. It is a long shot, but you might try turning off the hacked non-mirror support, resetting PRAM, & trying again.

Similar Messages

  • Mac OX Snow Leopard installation from DVD failed

    I tried to install the new OS Mac OS X Snow Leopard 10.6.3 (bought today) on my iMac. But is constantly failed (message: installation failed) and now it's in a loop where I can't get out. Because the only action there is is to try it again. What should I do?

    What specific iMac model do you have? Does it meet these requirements?
    Snow Leopard General requirements
    Mac computer with an Intel processor
    1GB of memory
    5GB of available disk space
    DVD drive for installation
    Some features require a compatible Internet service provider; fees may apply.
    Some features require Apple’s MobileMe service; fees and terms apply.
    To shut down the computer press and hold in the Power button until the computer shuts off. When you restart the computer you can eject the DVD as follows:
    Five ways to eject a stuck CD or DVD from the optical drive
    Ejecting the stuck disc can usually be done in one of the following ways:
    1. Restart the computer and after the chime press and hold down the left mouse button until the disc ejects.
    2. Press the Eject button on your keyboard.
    3. Click on the Eject button in the menubar.
    4. Press COMMAND-E.
    5. If none of the above work try this: Open the Terminal application in your Utilities folder. At the prompt enter or paste the following:
         /usr/bin/drutil eject
    If this fails then try this:
    Boot the computer into Single-user Mode. At the prompt enter the same command as used above. To restart the computer enter "reboot" at the prompt without quotes.
    If you are currently running Leopard and it's still working then do this:
    Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    If all is OK then reboot from your Snow Leopard DVD and try the installation again.
    BTW, I encourage you to make a cloned backup of your current working system before trying to upgrade.

  • Leopard installation problems

    I sort of forgot about the site below:
    http://www.apple.com/support/leopard/
    Among lots of other things, it addressed my troubles with Leopard installation. Worth a look if you are having problems.
    Romelle

    Update, when I login a promt comes up saying "the tablet driver did not load because of an internal driver failure"
    I don't know what that means if anyone has any info

  • Snow Leopard Installation problems

    What can I do if the Snow Leopard installation isn't completed, returning message " Installer couldn't replace system documents"?
    I tried once, and system returned me the message above. So I restarted and tried installation again, but first I formatted the HD with the Mac os x Journaled file system. the I retried, but the installation didn't go to an end, returning the same message.
    I'm stucked with a 2009 Macbook Pro. Before I tried installation, suddenly stopped working, booting it with no success, ending with a white wide screen.
    Any ideas?
    Many Thanks.
    Ricky

    Oh, it was the +File Open+ dialog, not a web browser window, is that correct?
    Since you installed Snow Leopard as an upgrade over your existing system, and logged in to your existing user account, you may have had a +Login Item+ (processes that start and run at login) that needs to use "Events.app" (or maybe Events.app itself was the Login Item).
    If you log out and log in, that message should pop up again, if it is related to a Login Item.
    To see your Login Items, go to System Preferences Accounts pane +Login Items+ tab. The list you see are your Login Items. If you see anything that you no longer need, you should remove it. Look for something that may be related to this "Events.app" process.

  • Mac Mini core solo 1.5gb snow leopard installation problem.

    Before I tried to install snow leopard I was in the middle of using the restore discs and before I was thinking about it I just turned the computer off when it asked for disc 2. Now I cannot do anything with this computer, turning it on goes to the installation menu and It just prompts for the second disc which I do not have. All my menus are disabled such as disc utility and can't start a fresh install. Also when I turn the computer on and hold the alt key down with a usb keyboard I do not get the option of selecting the snow leopard disc when the option of the hard drives come up. It just ejects the discs. Also tried holding down the C key to boot from dvd and no luck. Any way to get around this or another command to try?

    Sounds like your optical drive went out. Either get it fixed or use an external USB CD/DVD drive. You might try another disc first to eliminate a problem on your install disc. Sometimes scratches and finger prints on a disc can cause problems.
    Check out the new remodeled MacOSG website! 24-hour Apple-related news & support.
     MacOSG: An Apple User Group  iTunes: MacOSG Podcast  Follow us on Twitter: MacOSG

  • Leopard Installation Problem on PPC G5

    Hi there....any help on this one appreciated.
    I have a Dual 2Gig PPC G5 with 4.5 gigs RAM that was running (and still is) running 10.4.11 fine. Attempting to upgrade to Leopard from a proper retail Leopard install.
    Symptom: Either booting with c key down or running the upgrade from the OS results in a message saying "the installation could not be completed - if it continues to occur, the boot log may help you to diagnose the problem" - there are buttons to save and print the boot log and to shut down and restart...BUT the computer shuts itself down before I have a chance to act on any of this. Behind it I see an open boot log with a bunch of the word "crash" on it!!!!!
    Things I have tried:
    Resetting PRAM
    Removed third party PCIe cards
    Removed third party RAM
    I've repaired permissions on the startup disk
    I am fully backed up
    I've tried it from a different user account.
    I've disabled login items
    What more can I do aside from a complete clean install of 10.4 which may help? Trouble is I dont want to do that as it would take a day to get all my third party stuff re-installed.
    Any thoughts and help much appreciated
    cheers
    Tony

    Thanks MacJack,
    but...I didnt attempt this before as I dont think it works...
    from that doc you linked to:
    "Tip: FireWire Target Disk Mode works on internal ATA drives only. Target Disk Mode only connects to the master ATA drive on the Ultra ATA bus. It will not connect to Slave ATA, ATAPI or SCSI drives."
    So, as far as I understand it, if I booted up my macbook pro, say, with the Leopard install disk in it in Target Disk Mode - the g5 would only see the Macbook Pro's internal ATA as opposed to both that and the DVD or am I missing something? Sorry, not at that machine at the moment so I can't try it!
    Tony

  • Time Machine and Snow Leopard installation problem

    I'm trying to install Snow Leopard, but keep getting an error saying that my hard drive is used for time machin back ups. I have unplugged my external device, turned off time machine, yet this keeps happening. What am I doing wrong? I have been able to install Leopard on the computers that I haven't used time machine.

    BusyChris18 wrote:
    1) Do I have to do anything special with Time Machine BEFORE I install SL? I have been doing regular backups with TM.
    Do a "final" backup and turn TM off.
    2) should Time machine disc be off/disconnected when I do the install?
    It's safest to eject and disconnect it, "just in case."
    3) After I reconnect TM disc after SL install, do I have to "migrate" stuff from TM? OR will it just do a new backup and work like normal from that point forward.
    If you do the normal install, there's no migration needed. 99.9 % of everything will be fine. In some rare cases of 3rd-party apps putting things in unusual places, there may be a problem, and you may need to re-enter some 3rd-party app purchase codes.
    If you erase the drive, then install SL, then yes, of course, you'll have to transfer your data. There should be no reason to do that, but some folks seem to do it out of habit. If you do that, when your Mac boots up again, you can transfer your data from the TM backups. And if you do that, I'd strongly recommend making a separate full backup on a second external drive, again "just in case," preferably a "bootable clone." CarbonCopyCloner and SuperDuper are the most common. (There was a post here just last week where someone did this, the restore got to 99%, then BAM! the TM disk failed.)
    TM backups should just continue normally, although there will almost certainly be a long "Calculating Changes" phase (used to be called "Preparing"). And they've added a progress bar, which doesn't seem to be particularly accurate.
    However, it may try a new, full backup. If it does, cancel the backup and do a Restart. That may reset whatever confused it. If not, there's nothing you can do to prevent it.
    4) Will I be able to access files that were backuped when I have just Leopard?
    Yes.

  • Need advice on leopard installation problems!

    Over the summer I stopped in at the Apple store and was told that my Imac (which has the Jaguar operating system) would have no problems installing the Leopard OS. Well i finally bought Leopard and tried installing it last night and my computer is wrecked! I don't even know if I have an operating system anymore. grrrr.
    After almost 3 hours of waiting (my screen said "preparing for installation" the whole time...my computer froze up me. Finally a message popped up and said that the leopard OS "cannot be installed on this computer". It gave me the option of exiting installation. Once i selected the exit option, NOTHING happened. My computer did nothing. The icon kept swirling around and around and around. I tried force quitting and that did nothing.
    So now ive got this leopard disc stuck in my computer's disc drive and i have no way to get it out. it was such a waste of money for this. I feel completely misinformed by the Apple employee.
    Does anyone know what is going on with this? How can I get the disk out?
    -Carly

    MissMerryMac wrote:
    Over the summer I stopped in at the Apple store and was told that my Imac (which has the Jaguar operating system) would have no problems installing the Leopard OS. Well i finally bought Leopard and tried installing it last night and my computer is wrecked! I don't even know if I have an operating system anymore. grrrr.
    After almost 3 hours of waiting (my screen said "preparing for installation" the whole time...my computer froze up me. Finally a message popped up and said that the leopard OS "cannot be installed on this computer". It gave me the option of exiting installation. Once i selected the exit option, NOTHING happened. My computer did nothing. The icon kept swirling around and around and around. I tried force quitting and that did nothing.
    So now ive got this leopard disc stuck in my computer's disc drive and i have no way to get it out. it was such a waste of money for this. I feel completely misinformed by the Apple employee.
    Does anyone know what is going on with this? How can I get the disk out?
    -Carly
    Welcome to the Apple forums.
    Sadly I wish you had posted here before installing Leopard, but we do not dwell in the past here.
    You did not say which of the three types of install you did: Default (merge), Archive or Erase and install.
    You most likely still have your original OS intact and I assume you did not create a backup of the system before installing. Nothing is perfect and having a copy of your system before changing it is normal, even if you are simply upgrading your original OS. In today's world, a backup is a necessity, not an option.
    Can you perform a Safe boot? Hold down the shift key after the boot bell.
    Can you boot into the original CD by holding down the "C" key whilst booting?
    I do not think you have lost anything, but we must be careful in proceeding forward.
    If you can create a copy of your existing HD, that would be great for a start.
    Try the Safe boot and post back. We are here to help. This is a user-to-user forum and we take everything seriously and do our best to fix things up.
    I do like your user name
    Message was edited by: nerowolfe

  • Snow Leopard Installation Problems with Bridge

    I just installed Snow Leopard, after having the CS4 Suite with Bridge CS4 previously installed. When I tried to open Bridge after the insallatin of Snow Leopard, I got four error messages in succession, one right after the other when hitting "ok":
    1. PiPL Endian Swap Error
    Please Update PALoadMacPlugins.ccp with prop.
    Unable to Swap PiPLprop 'ms32"   øms325 §'
    2. PiPL Endian Swap Error
    Please Update PALoadMacPlugins.ccp with prop.
    3. PiPL Endian Swap Error
    Please Update PALoadMacPlugins.ccp with prop.
    Unable to Swap PiPLprop 'ms32"   øms325 §'
    4. PiPL Endian Swap Error
    Please Update PALoadMacPlugins.ccp with prop.
    After that, the program opens normally. I re-installed Bridge CS2, which works, but when I tried to use the update for Bridge CS4, it wouldn't allow me to put it in. On the installation disc for CS4, the place to select Bridge for installation was grayed out.

    I didn't get any fix advice.
    When I reinstalled CS4 I didn't install the any of the bonus packs/updates and haven't had the problem.
    I also had (for other reasons) to do a complete reinstall of my system software, which may be why it's fixed.  I'm afraid to install the bonus pack and find out, in any case.

  • My Leopard installation problems solved

    My Preparations
    I had received an update for the 1.1 firmware update (OSx 10.4.10), but it would not install. It turned out, the disk was not a "GUID" partition. I backed up the disk after having problems with 2 files it said it could not find. Finally found these were some mirror files under /users/art/Library/Mirrors (the backup had stopped on the Mirrors directory). Had no idea what they were or where they came from, but copied them to another drive and then deleted them. After that, the backup worked. The internal drive was a Hitachi 100 GB, 7200 RPM that replace the original 80 GB drive. I had done a Carbon Copy clone, but guess it was not exactly a clone.
    I repartitioned the drive as GUID HPFS+ and done a clean install of 10.4.8 and also done a migration from the backup, then done an update to 10.4.10 where the firmware update worked. So I had the fully updated internal 10.4.10 and a bootable USB 80 GB drive.
    The Leopard Install
    I selected the install/archive option, and Leopard installed with no problems including migrating the applications from the previous install. I did not have the applications enhancement which I do not even know what is. I then let Leopard do an update where it updated the Quicktime and another program whose name slips my mind right now. It said it had to reboot and did where it installed the programs, but then when the reboot started, it come up with the rotating beach ball at the login screen and would just keep rebooting. Tried everything that was mentioned the discussion group but nothing worked. I ended up using the Disk Utility to erase with write zeros, then a clean install. Everything went fine, update went fine, and it was much faster than before by 4 or 5 times. Went and got my applications from the backup and updated those with updates for Leopard including Parallels, Vuescan, Skype, Firefox, Thunderbird, NeoOffice, and a few others. System is now working fine and is much faster the 10.4.10. Oh, I did have to update my DIR655 wireless router for the wireless also.
    (Macbook was purchased here in Taiwan where it is made with Chinese Leopard US English installation)
    The one word of advice I would give to anyone, make a bootable backup of your operating system. I am glad I did, it saved my bacon.
    Art

    I can only say, "Well done."
    Good sleuthing, excellent prep and not really a problem after all.
    Enjoy

  • Final Cut Pro 6 on Mac OS Snow Leopard installation problem HELP!!!

    After 2 - 3 hours of installing all 10 FCS 2.0 discs and Software Updates, I can't seem to launch Final Cut Pro 6.0.6. I get *"...software maybe damaged or not installed.."* So I removed all of them and only custom-installed Final Cut Pro 6.0.6. It works with no problem!!! Then I custom-installed Soundtrack, Motion, DVD Studio Pro etc..., I can't launch Final Cut Pro 6.0.6. again! What the **** is going on? I get that "damaged" warning and Final Cut Pro icon is replaced by missing application icon.
    My Mac Pro also has _Pro Tools 8 LE_ with _003 Mixer Rack connect to USB_. That's it. No other application. You think this is maybe causing the problem?
    Anyone having similar problem?

    https://discussions.apple.com/docs/DOC-2494
    Carbon Copy Cloner is pretty simple to use.  If you have any questions, post back or read the documentation.  As I said in the user tip, test your clone after you make it to be sure it is bootable and your apps work.

  • Snow Leopard installation problem on Mac Pro

    Hello Partners!
    I have the following mashine:
    (sorry for Russian, but i see - it is the clear information)
    Название модели:          Mac Pro
      Идентификатор модели:          MacPro3,1
      Имя процессора:          Quad-Core Intel Xeon
      Скорость процессора:          2.8 ГГц
      Количество процессоров:          2
      Общее количество ядер:          8
      Кэш 2-го уровня (в каждом процессоре):          12 МБ
      Память:          10 ГБ
      Частота шины:          1.6 ГГц
      Версия Boot ROM:          MP31.006C.B05
      Версия SMC (система):          1.25f4
      Серийный номер (система):          CK******1Z9
      UUID аппаратного обеспечения:         ****
    When begin the installation on Snow Leopard 10.6.4 -
    i have the message - that Can not install to this computer -
    and the installation has been interrupted...
    Could you tell - Why?
    Thanks in advance,
    Alecey Batin, Ekaterinburg, Russia.
    <Edited By Host>

    Ralph,
    glad to hear that guys near you - nice people and you have the kind-neighbors relations,
    i think it is more then usual for "russians" (not important - Ukrain etc..) ...
    I am sure that "System-s" - are one way, people - parallel way evertimes -
    and they do not across ...
    Was nice to speak here with you and other guys. Really!
    O, do not know how it will be seen from US (what about Rusiian-English interface) -
    but if you wish - you can see many good picturse (albums from foot-trips in Nature, Russia and other place)
    an my page mentioned in Profile here.
    Thanks for messages, may be not the last - life not so short ...

  • Leopard installation problems (from tiger 10.4.11)

    I've been on Tiger but today I've updated to leopard using the update disc (ie not the $129/£85 version of leopard but the $9.95/£5.95 update disc)
    Installation went fine but Im pretty sure I forgot to restart my mac after it.
    Anyways I carried on with the update to 10.5.1. from the apple site (which I downloaded through safari browser. That went fine too, then I restarted my mac.
    I started exploring leopard and now I need help!
    firstly, Safari just wont open. It says safari wont work with this version of mac os x, therefore Im typing this through camino.
    Secondly, photo booth is the same as in tiger, no new updates etc but now the effects screen has just gone weird; (see pic) (the camera is taking a pic of a white background by the way)
    I admit I did change some locations of apps in the apps folder for example, when I was on tiger, i created a subfolder in the apps folder entitled 'Web browsers', and put safari, camino, firefox into. Did a similar thing to photo booth app too.
    But then I read on a forum that when upgrading OS's apps should be in the 'default' location before upgrading. So I moved all these apps back to the apps folder, but this hasnt changed anything.
    Also, when viewing folders in icon mode, at a large icon size, the icons all overlap until i go to view in the menu bar, select arrange by name, then its all evened out, but I wish it'd just work properly!
    Also not a big deal but I though that when viewing in icon mode that you should be able to see a little screenshot preview of the item/document instead of an icon (eg. instead of a blank pages for a pages document, should you not see a mini preview of the fist page of the actual document as the icon?)
    Im sure there is other things too that aren't as they ought to be.
    So I ask, how do i fix this mess? I cant uninstall leopard i dont think, and i dont have an external hard drive to backup to.
    Any suggestions please?
    Regards, Ben.

    I'm just going by instinct here, but after you move the apps back where they belong, try reinstalling the 10.5.1 update again. Maybe it will "straighten" things out.
    Yes, one should never move system folders or apps to other folders. That's a real NONO. You can usually move 3rd party apps around, but the OS-X looks for certain apps in certain places. Safari is more than just an app - it's tightly integrated into the OS, and there are also many apps that attach to it such as realtime, etc., that may not be able to find it if you play hide-and-seek with it.
    So restore all the system apps to their original locations and see if a reinstall of 10.5.1 will help.
    Use the 110MB download on the Apple website.

  • Snow leopard installation dvd keeps ejecting on Mac Mini

    HI,
    I have a Mac Mini, 1.83ghz, intel core duo, 2gb 667mhz DDR2 SDRAM running OS Leopard 10.5.8.
    Im trying to install snow leopard from the dvd onto the mac and it keeps ejecting it.
    It wont even mount on the desktop, can anyone help?
    Ive restarted holding the 'c' key but it still ejects the dvd. The dvd doesnt look damaged or scratched either and have disconnected all my peripherals as well.
    Cheers Pete

    Pete,
    This may sound so simple but it may be the problem.  Unplug your USB keyboard and just plug in your mouse.  Then insert the DVD.  If it stays in, you have a sticky key on the keyboard.  Cleaning your keyboard may be all that it takes.
    Otherwise, your optical drive is not recognizing the platter and you have more serious issues.  Rule out the easy and obvious first.
    Jim~

  • Help!  'Leopard CPU Drop-in DVD' Ejecting on Brand new macbook pro

    Hey everyone. I just recieved my highly anticipated Macbook Pro that came preinstalled with OSX 10.4.10. I haven't installed anything yet because i am wanting to install Leopard first. The computer came with the 'Mac OS X Leopard - CPU Drop-in DVD'. After I put the dvd in i have tried to install it 4 different ways. One, just by double clicking the 'Install Mac OS X.app' icon (i've actually tried this about 4 times). Second, I tried to install it by using the Leopard DVD as the start-up disc as described in the 'troubleshooting leopard' doc online. Thirdly, I tried (three times) to restart the computer with the DVD in while holding 'C' down. And finally, my last attempt i installed the Tiger discs thinking that might do it...after i installed Tiger which was already preinstalled on the computer, I repeated the above mentioned methods...and everytime the dvd gets ejected on the restart...a couple seconds after the 'apple logo' appears on bootup...then, the 'not working' icon (circle with the diagonal line through it like 'no smoking' logo) appears.
    help!!! i'm anxious to get Leopard running!!!! i've been dreaming about this computer for about 3 years now.
    any help is appreciated!!!

    ok...i'm not sure how at all...but, a couple hours have passed since i posted this and while i was hoping someone would reply i was finishing up some old work on my old, extremely slow emac. anyways, i decided to go ahead and try to install leopard again from the normal standard method. (which is just clicking the icon once the leopard install window comes up). Guess what? now it's 50% into the installation!! i don't want to count my chickens before they hatch...especially after some of the discussions i've read about leopard so far...but, i'm hopeful
    who knows how...i'm clueless and it doesn't make much sense to me. but, i'll come back and let anyone who cares know how the install went.
    note for anyone with similar problems:
    another strange fix to the 'leopard dvd ejecting on install' is to let the dvd chill in the drive for a couple hours...then try it again. HAHAHAHAHA!!!! worked for me

Maybe you are looking for

  • Printing queue for HP Photosmart 2400xi

    I have an HP Pavilion printer and I need to delete some scheduled printing.  How do I locate the printing queue??? Message Edited by lvnv on 02-18-2009 02:32 PM

  • ALV grid total  or based on two key fields

    Hello experts, I have ALV grid with  vendor, g/l account and amount field. I want to have sum or total of each vendor, and if vendor having mutliple g/l accounts i want to have sum for each g/l account. ex:  vendor   g/l account    amount.         10

  • Label becomes nil when coming from UIView in UIViewController

    Hi, I'm trying to call a method in UIViewController from UIView to change the UILabel in UIViewController by passing a NSString argument from UIView. But it doesn't the UILabel becoz the UILabel becomes nil in UIViewController. But method is called p

  • The screen goes black after restarting Windows

    I downloaded the Support Software to a FAT-32 flash drive and partitioned the main hard drive inside my Late 2009 Macbook running Lion. The Windows starter worked fine and I installed Windows 7 Professional. The installation worked just fine and I wa

  • Fbean

    Hi, I was trying to develop a form, which looks like a web page with urls to other forms. I tried using fbean (using hyperlink), I am able to generate the page but I want to get URLs from the table. e.g. table t_urls (seq_no, label, url) ===== I trie