License for SIP trunk?
Hi Guys, we are going to setup a few SIP Trunks between CUCM 7.1.3 and third party FAX server. Do we need extra license for this SIP trunk? I had a look at the license calculator but it doesn't mention any SIP trunks. So I think it will not consume any license units, am I correct?
Thanks. Leo
Yes, correct, no licenses required/consumed for/by SIP Trunk.
GP.
Pls rate the post if it helps !!
Similar Messages
-
Cca xml export for SIP Trunk service providers, request or schema.
Hi
Please can I have the complete xml schema for SIP trunks so I can create a proper template?
Exporting from CCA 3.2.2 gives me an incomplete and sometimes inaccurate xml file
example: toll fraud protection - I would like to add this in to the template - how
SIP registration: If I set this to 120 on CCA and export - the exported template remains as 3600
thanks
AdamHi Adam,
Are you saying when you try to export your SIP trunk settings via CCA that your settings are incorrect in the xml file? If so, I recommend opening a case to troubleshoot the issue as it sounds like a bug to me. -
How to Remove port number for SIP trunk in CME
Hi,
I trying to set a SIP trunk with SIP provider, I have CME 7.1
The trunk is registered now but I can´t make calsl via SIP provider. After some debbugs sip provider's staff told me that the solution is not
not append the port in the INVITE.
Is it possible to do this?, How?
I have found some info about normalization but is relating to CM server not CME.
regardswhat port number does your provider use for signalling? They need to provide you the port number if its different from the standard 5060..
You can then configure the signalling ports on your dial-peer as shown in example below..where port 5081 is used here
dial-peer voice 1 voip
destination-pattern .T
session protocol sipv2
session target ipv4:10.10.10.24:5081
Please rate all useful posts
"opportunity is a haughty goddess who waste no time with those who are unprepared" -
Sofware license for SIP protocol
I AM LOOKING FOR A CONFIRMATION REGARDING SOFTWARE license. I apoke earlier with a Cisco's representative asking him if software license is needed for usinh IP telephone, without a conecction to CISCI'S operator. I intend to use SIP technology. Cisco's rep asnwer was that license is not needed. Please assist with a writen confiemation to that answer. Thanks for the assitance.
Hi Eyal,
Here is the clearest documentation I have seen in regards to your question;
ORDERING INFORMATION
Ordering has become to complex to place the order code numbers. Note that "All Cisco IP Phones require the purchase of a phone technology license, regardless of the call protocol server phone is attached to."
From this good doc;
http://www.cisco.com/en/US/products/hw/phones/ps379/products_data_sheet09186a008008884a.html
Hope this helps!
Rob
Please remember to rate helpful posts..... -
Anyone use CUBE for SIP trunking? Have a read.
voice service voip
sip
silent discard-untrusted
Silent discard was added in 15.3.3M to make the router not send 403 errors to untrusted entities...which exposes the router (validates that it's there essentially).
Might want to add that when upgrading to that version.
TracyThanks for sharing
=============================
Please remember to rate useful posts, by clicking on the stars below.
============================= -
SIP Trunk - No voice with Single Number Reach
Hi Community.
I setup SIP Trunk with the CCA. Everything is working Call In and Call Out. Call Forward and so on.
But with Single Number reach is something wrong. The mobile phone is ringing and I can get the call, but I hear not any voice.
Can someone please help me out? Below the config.
version 15.1
parser config cache interface
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service internal
service compress-config
service sequence-numbers
dot11 ssid cisco-data
vlan 1
authentication open
dot11 ssid cisco-voice
vlan 100
authentication open
ip source-route
ip cef
ip dhcp relay information trust-all
ip dhcp excluded-address 10.1.1.1 10.1.1.9
ip dhcp excluded-address 10.1.1.241 10.1.1.255
ip dhcp pool phone
network 10.1.1.0 255.255.255.0
default-router 10.1.1.1
option 150 ip 10.1.1.1
ip domain name site1.365873.trk.ipvoip.ch
ip name-server 8.8.8.8
ip inspect WAAS flush-timeout 10
ip inspect name SDM_LOW dns
ip inspect name SDM_LOW ftp
ip inspect name SDM_LOW h323
ip inspect name SDM_LOW https
ip inspect name SDM_LOW icmp
ip inspect name SDM_LOW imap
ip inspect name SDM_LOW pop3
ip inspect name SDM_LOW netshow
ip inspect name SDM_LOW rcmd
ip inspect name SDM_LOW realaudio
ip inspect name SDM_LOW rtsp
ip inspect name SDM_LOW esmtp
ip inspect name SDM_LOW sqlnet
ip inspect name SDM_LOW streamworks
ip inspect name SDM_LOW tftp
ip inspect name SDM_LOW tcp router-traffic
ip inspect name SDM_LOW udp router-traffic
ip inspect name SDM_LOW vdolive
no ipv6 cef
multilink bundle-name authenticated
stcapp ccm-group 1
stcapp
isdn switch-type basic-net3
voice call send-alert
voice rtp send-recv
voice service voip
ip address trusted list
ipv4 0.0.0.0 0.0.0.0
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
no supplementary-service sip refer
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
sip
registrar server expires max 3600 min 3600
localhost dns:site1.365873.trk.ipvoip.ch
no update-callerid
voice class codec 1
codec preference 1 g711alaw
voice register global
mode cme
source-address 10.1.1.1 port 5060
load 9971 sip9971.9-2-2
load 9951 sip9951.9-2-2
load 8961 sip8961.9-2-2
timezone 23
voice source-group CCA_SIP_SOURCE_GROUP_CUE_CME
access-list 2
translation-profile incoming SIP_Incoming
voice source-group CCA_SIP_SOURCE_GROUP_EXTERNAL
access-list 3
voice translation-rule 9
rule 1 /0041449475090/ /90/
rule 2 /0041449475091/ /91/
rule 3 /0041449475092/ /92/
rule 4 /0041449475093/ /93/
rule 5 /0041449475094/ /94/
rule 6 /0041449475095/ /95/
rule 7 /0041449475096/ /96/
rule 8 /0041449475097/ /97/
rule 9 /0041449475098/ /98/
rule 10 /0041449475099/ /99/
voice translation-rule 410
rule 1 /^0\(.*\)/ /\1/
rule 15 /^..$/ /0041449475090/
voice translation-rule 411
rule 1 /^0\(.*\)/ /ABCD0\1/
voice translation-rule 412
rule 1 /^ABCD\(.*\)/ /\1/
voice translation-rule 422
rule 15 /^ABCD\(.*\)/ /\1/
voice translation-rule 1000
rule 1 /.*/ //
voice translation-rule 1111
rule 1 /^9\([1-9]\)$/ /004144947509\1/
rule 15 /^..$/ /0041449475090/
voice translation-rule 1112
rule 1 /^0/ //
voice translation-rule 2000
rule 1 /0041449475098/ /98/
voice translation-rule 2001
rule 1 /0041449475097/ /97/
voice translation-rule 2002
rule 1 /^6/ //
voice translation-rule 2222
voice translation-profile AA_Profile
translate called 2001
voice translation-profile CALLER_ID_TRANSLATION_PROFILE
translate calling 1111
voice translation-profile CallBlocking
translate called 2222
voice translation-profile OUTGOING_TRANSLATION_PROFILE
translate called 1112
voice translation-profile PSTN_CallForwarding
translate redirect-target 410
translate redirect-called 410
voice translation-profile PSTN_Outgoing
translate calling 1111
translate called 1112
translate redirect-target 410
translate redirect-called 410
voice translation-profile SIP_Called_9
translate calling 3265
translate called 9
voice translation-profile SIP_Incoming
translate called 411
voice translation-profile SIP_Passthrough
translate called 412
voice translation-profile SIP_Passthrough_CallBlocking
translate called 422
voice translation-profile VM_Profile
translate called 2000
voice translation-profile XFER_TO_VM_PROFILE
translate redirect-called 2002
voice translation-profile nondialable
translate called 1000
voice-card 0
dspfarm
dsp services dspfarm
fax interface-type fax-mail
license udi pid UC540W-BRI-K9 sn FGL163220SL
archive
log config
logging enable
logging size 600
hidekeys
username admin privilege 15 secret xxx
username xxx password 0 ""
username xxx password 0 ""
ip tftp source-interface Loopback0
bridge irb
interface Loopback0
description $FW_INSIDE$
ip address 10.1.10.2 255.255.255.252
ip access-group 101 in
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/0
description $FW_OUTSIDE$
no ip address
ip inspect SDM_LOW out
ip virtual-reassembly in
ip verify unicast reverse-path
load-interval 30
shutdown
duplex auto
speed auto
interface Integrated-Service-Engine0/0
description cue is initialized with default IMAP group
ip unnumbered Loopback0
ip nat inside
ip virtual-reassembly in
service-module ip address 10.1.10.1 255.255.255.252
service-module ip default-gateway 10.1.10.2
interface FastEthernet0/1/0
no ip address
macro description cisco-desktop
spanning-tree portfast
interface FastEthernet0/1/1
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/2
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/3
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/4
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/5
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/6
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/7
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/8
no ip address
macro description cisco-desktop
spanning-tree portfast
interface BRI0/1/0
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn sending-complete
isdn static-tei 0
interface BRI0/1/1
no ip address
shutdown
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn sending-complete
isdn static-tei 0
interface Dot11Radio0/5/0
no ip address
ssid cisco-data
ssid cisco-voice
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
antenna receive right
antenna transmit right
interface Dot11Radio0/5/0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0/5/0.100
encapsulation dot1Q 100
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 spanning-disabled
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
interface Vlan1
no ip address
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan100
no ip address
bridge-group 100
bridge-group 100 spanning-disabled
interface BVI1
description $FW_INSIDE$
ip address 192.168.10.2 255.255.255.0
ip access-group 102 in
ip nat inside
ip virtual-reassembly in
interface BVI100
description $FW_INSIDE$
ip address 10.1.1.1 255.255.255.0
ip access-group 103 in
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http path flash:/gui
ip dns server
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 192.168.10.1
ip route 10.1.10.1 255.255.255.255 Integrated-Service-Engine0/0
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 10.1.1.0 0.0.0.255
access-list 1 permit 192.168.10.0 0.0.0.255
access-list 1 permit 10.1.10.0 0.0.0.3
access-list 2 remark CCA_SIP_SOURCE_GROUP_ACL_INTERNAL
access-list 2 remark SDM_ACL Category=1
access-list 2 permit 192.168.10.2
access-list 2 permit 10.1.10.0 0.0.0.3
access-list 2 permit 192.168.10.0 0.0.0.255
access-list 2 permit 10.1.1.0 0.0.0.255
access-list 3 remark CCA_SIP_SOURCE_GROUP_ACL_EXTERNAL
access-list 3 remark SDM_ACL Category=1
access-list 3 permit 212.147.47.216
access-list 3 deny any
access-list 100 remark auto generated by SDM firewall configuration
access-list 100 remark SDM_ACL Category=1
access-list 100 deny ip 192.168.10.0 0.0.0.255 any
access-list 100 deny ip host 255.255.255.255 any
access-list 100 deny ip 127.0.0.0 0.255.255.255 any
access-list 100 permit ip any any
access-list 101 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 101 remark SDM_ACL Category=1
access-list 101 permit tcp 10.1.1.0 0.0.0.255 eq 2000 any
access-list 101 permit udp 10.1.1.0 0.0.0.255 eq 2000 any
access-list 101 deny ip 10.1.1.0 0.0.0.255 any
access-list 101 deny ip 192.168.10.0 0.0.0.255 any
access-list 101 deny ip 192.168.1.0 0.0.0.255 any
access-list 101 deny ip host 255.255.255.255 any
access-list 101 deny ip 127.0.0.0 0.255.255.255 any
access-list 101 permit ip any any
access-list 102 remark auto generated by SDM firewall configuration##NO_ACES_6##
access-list 102 remark SDM_ACL Category=1
access-list 102 deny ip 10.1.10.0 0.0.0.3 any
access-list 102 deny ip 10.1.1.0 0.0.0.255 any
access-list 102 deny ip 192.168.1.0 0.0.0.255 any
access-list 102 deny ip host 255.255.255.255 any
access-list 102 deny ip 127.0.0.0 0.255.255.255 any
access-list 102 permit ip any any
access-list 103 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 103 remark SDM_ACL Category=1
access-list 103 permit tcp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 permit udp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 deny ip 10.1.10.0 0.0.0.3 any
access-list 103 deny ip 192.168.10.0 0.0.0.255 any
access-list 103 deny ip 192.168.1.0 0.0.0.255 any
access-list 103 deny ip host 255.255.255.255 any
access-list 103 deny ip 127.0.0.0 0.255.255.255 any
access-list 103 permit ip any any
access-list 104 remark auto generated by SDM firewall configuration##NO_ACES_14##
access-list 104 remark SDM_ACL Category=1
access-list 104 deny ip 10.1.10.0 0.0.0.3 any
access-list 104 deny ip 10.1.1.0 0.0.0.255 any
access-list 104 permit ip any any
access-list 104 permit udp host 8.8.8.8 eq domain any
access-list 104 permit icmp any any echo-reply
access-list 104 permit icmp any any time-exceeded
access-list 104 permit icmp any any unreachable
access-list 104 deny ip 10.0.0.0 0.255.255.255 any
access-list 104 deny ip 172.16.0.0 0.15.255.255 any
access-list 104 deny ip 192.168.0.0 0.0.255.255 any
access-list 104 deny ip 127.0.0.0 0.255.255.255 any
access-list 104 deny ip host 255.255.255.255 any
access-list 104 deny ip host 0.0.0.0 any
access-list 104 deny ip any any
control-plane
bridge 1 route ip
bridge 100 route ip
voice-port 0/0/0
cptone CH
station-id name FAX
station-id number 99
caller-id enable
voice-port 0/0/1
cptone CH
shutdown
caller-id enable
voice-port 0/0/2
cptone CH
shutdown
caller-id enable
voice-port 0/0/3
cptone CH
shutdown
caller-id enable
voice-port 0/1/0
compand-type a-law
cptone CH
bearer-cap Speech
voice-port 0/1/1
compand-type a-law
cptone CH
bearer-cap Speech
voice-port 0/4/0
auto-cut-through
signal immediate
input gain auto-control -15
description Music On Hold Port
sccp local Loopback0
sccp ccm 10.1.1.1 identifier 1 version 4.0
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate profile 2 register mtpa4934c6ee4e0
dspfarm profile 2 transcode
description CCA transcoding for SIP Trunk VTX
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
maximum sessions 10
associate application SCCP
dial-peer cor custom
name internal
name local
name local-plus
name international
name national
name national-plus
name emergency
name toll-free
dial-peer cor list call-internal
member internal
dial-peer cor list call-local
member local
dial-peer cor list call-local-plus
member local-plus
dial-peer cor list call-national
member national
dial-peer cor list call-national-plus
member national-plus
dial-peer cor list call-international
member international
dial-peer cor list call-emergency
member emergency
dial-peer cor list call-toll-free
member toll-free
dial-peer cor list user-internal
member internal
member emergency
dial-peer cor list user-local
member internal
member local
member emergency
member toll-free
dial-peer cor list user-local-plus
member internal
member local
member local-plus
member emergency
member toll-free
dial-peer cor list user-national
member internal
member local
member local-plus
member national
member emergency
member toll-free
dial-peer cor list user-national-plus
member internal
member local
member local-plus
member national
member national-plus
member emergency
member toll-free
dial-peer cor list user-international
member internal
member local
member local-plus
member international
member national
member national-plus
member emergency
member toll-free
dial-peer voice 1 pots
destination-pattern 99
port 0/0/0
no sip-register
dial-peer voice 2 pots
port 0/0/1
no sip-register
dial-peer voice 3 pots
port 0/0/2
no sip-register
dial-peer voice 4 pots
port 0/0/3
no sip-register
dial-peer voice 5 pots
description ** MOH Port **
destination-pattern ABC
port 0/4/0
no sip-register
dial-peer voice 6 pots
description tcatch all dial peer for BRI/PRIv
translation-profile incoming nondialable
incoming called-number .%
direct-inward-dial
dial-peer voice 50 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
direct-inward-dial
port 0/1/0
dial-peer voice 51 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
direct-inward-dial
port 0/1/1
dial-peer voice 2000 voip
description ** cue voicemail pilot number **
translation-profile outgoing XFER_TO_VM_PROFILE
destination-pattern 98
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 2001 voip
description ** cue auto attendant number **
translation-profile outgoing PSTN_CallForwarding
destination-pattern 97
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 2012 voip
description ** cue prompt manager number **
translation-profile outgoing PSTN_CallForwarding
destination-pattern 96
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1000 voip
permission term
description ** Incoming call from SIP trunk (VTX) **
session protocol sipv2
session target sip-server
incoming called-number .%
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
fax rate 14400
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1001 voip
corlist outgoing call-local
description ** star code to SIP trunk (VTX) **
destination-pattern *..
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
fax rate 14400
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1003 voip
description ** Passthrough Inbound Calls for PSTN from CUE **
translation-profile incoming SIP_Passthrough
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
incoming called-number ABCDT
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1005 voip
description ** Passthrough Inbound Calls for MWI from CUE **
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
incoming called-number A80T
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1009 voip
description ** Passthrough Inbound Calls for Internal Extensions from CUE **
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
incoming called-number ^..$
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1033 voip
corlist outgoing call-local
description **CCA*Switzerland*Short Code Services**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 0187
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1042 voip
corlist outgoing call-emergency
description **CCA*Switzerland*Ambulance / Poisioning**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 0014[45]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1041 voip
corlist outgoing call-emergency
description **CCA*Switzerland*REGA Air Rescue**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 00333333333
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1025 voip
corlist outgoing call-national
description **CCA*Switzerland*National Destination Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00[789]1.......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1020 voip
corlist outgoing call-national
description **CCA*Switzerland*Regional Announcement VM**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 01600
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1040 voip
corlist outgoing call-emergency
description **CCA*Switzerland*REGA Air Rescue**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 000333333333
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1043 voip
corlist outgoing call-emergency
description **CCA*Switzerland*Ambulance / Poisioning**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 014[45]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1035 voip
corlist outgoing call-national
description **CCA*Switzerland*Mobile Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 007[46789].......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1024 voip
corlist outgoing call-national-plus
description **CCA*Switzerland*Personal Numbering**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00878......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1029 voip
corlist outgoing call-national
description **CCA*Switzerland*Voicemail Access**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00860.........
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1036 voip
corlist outgoing call-national
description **CCA*Switzerland*VPN Access**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00869.............
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1027 voip
corlist outgoing call-national-plus
description **CCA*Switzerland*Premium Rate (Business)**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00900......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1026 voip
corlist outgoing call-national
description **CCA*Switzerland*Test Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00868T
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1034 voip
corlist outgoing call-national-plus
description **CCA*Switzerland*Shared Cost numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 0084[0248]......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1038 voip
corlist outgoing call-emergency
description **CCA*Switzerland*Emergency**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 0011[278]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1037 voip
corlist outgoing call-toll-free
description **CCA*Switzerland*Toll Free Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00800......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1039 voip
corlist outgoing call-emergency
description **CCA*Switzerland*Emergency**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 011[278]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1032 voip
corlist outgoing call-national
description **CCA*Switzerland*National Destination Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00[23456]........
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1023 voip
corlist outgoing call-international
description **CCA*Switzerland*International Calls**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 000T
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1031 voip
description **CCA*Switzerland*Premium Rate (Social)**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 0090[16]......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1030 voip
corlist outgoing call-national
description **CCA*Switzerland*Short Code**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 014[0357]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1045 voip
corlist outgoing call-emergency
description **CCA*Switzerland*REGA/Glaciers Air Rescue**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 0141[45]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1028 voip
corlist outgoing call-national-plus
description **CCA*Switzerland*Directory Enquiries**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 018[15].
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1021 voip
corlist outgoing call-national
description **CCA*Switzerland*Short Code**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 011[45].
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1022 voip
corlist outgoing call-national
description **CCA*Switzerland*Short Code Services**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 01[67].
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1044 voip
corlist outgoing call-emergency
description **CCA*Switzerland*REGA/Glaciers Air Rescue**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 00141[45]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 2002 voip
description ** cue voicemail PSTN number **
translation-profile outgoing VM_Profile
destination-pattern xxx$
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 2003 voip
description ** cue auto attendant PSTN number **
translation-profile outgoing AA_Profile
destination-pattern xxx$
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1110 pots
preference 9
destination-pattern xxx
port 0/0/0
no sip-register
dial-peer voice 3006 voip
description SIP
translation-profile incoming SIP_Called_9
session protocol sipv2
session target sip-server
incoming called-number xxx.
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
no dial-peer outbound status-check pots
sip-ua
keepalive target dns:site1.365873.trk.ipvoip.ch
authentication username xxx password 7 xxx
no remote-party-id
retry invite 2
retry register 10
timers connect 100
timers keepalive active 100
registrar dns:site1.365873.trk.ipvoip.ch expires 3600
sip-server dns:site1.365873.trk.ipvoip.ch
host-registrar
telephony-service
sdspfarm units 5
sdspfarm transcode sessions 10
sdspfarm tag 2 mtpa4934c6ee4e0
video
fxo hook-flash
max-ephones 40
max-dn 300
ip source-address 10.1.1.1 port 2000
auto assign 1 to 1 type bri
calling-number initiator
service phone videoCapability 1
service phone ehookenable 1
service phone ehookEnable 1
service dnis overlay
service dnis dir-lookup
service dss
timeouts interdigit 5
system message SwissT.Net
url services http://10.1.10.1/voiceview/common/login.do
url authentication http://10.1.10.1/voiceview/authentication/authenticate.do
cnf-file location flash:
cnf-file perphone
user-locale U4 load CME-locale-de_DE-German-8.1.2.2.tar
network-locale U4
load 521G-524G cp524g-8-1-17
load 525G spa525g-7-5-4
load 501G spa50x-30x-7-5-2b
load 502G spa50x-30x-7-5-2b
load 504G spa50x-30x-7-5-2b
load 508G spa50x-30x-7-5-2b
load 509G spa50x-30x-7-5-2b
load 525G2 spa525g-7-5-4
load 301 spa50x-30x-7-5-2b
load 303 spa50x-30x-7-5-2b
time-zone 23
time-format 24
date-format dd-mm-yy
keepalive 30 auxiliary 4
voicemail 98
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
hunt-group logout HLog
moh flash:/media/music-on-hold.au
multicast moh 239.10.16.16 port 2000
web admin system name cisco secret 5 xxx
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern .T
transfer-pattern 0.T
transfer-pattern 6.. blind
secondary-dialtone 0
night-service day Sun 17:00 09:00
night-service day Mon 17:00 09:00
night-service day Tue 17:00 09:00
night-service day Wed 17:00 09:00
night-service day Thu 17:00 09:00
night-service day Fri 17:00 09:00
night-service day Sat 17:00 09:00
fac standard
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-template 1
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
service phone webAccess 0
softkeys remote-in-use Newcall
softkeys idle Redial Pickup Mobility Newcall Cfwdall Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Trnsfer Mobility TrnsfVM Confrn Acct Park
button-layout 7931 2
ephone-template 15
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use Newcall
softkeys idle Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
button-layout 7931 2
ephone-template 16
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use Newcall
softkeys idle Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
ephone-template 17
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use CBarge Newcall
softkeys idle Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
ephone-template 18
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use CBarge Newcall
softkeys idle Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
button-layout 7931 2
ephone-dn 9
number BCD no-reg primary
description MoH
moh out-call ABC
ephone-dn 292
number xxx
description SIP Main Number registration
preference 10
ephone-dn 293 dual-line
number 90 secondary xxx no-reg both
label Zentrale
description 90
name Zentrale
call-forward busy 98
call-forward noan 98 timeout 20
ephone-dn 294 dual-line
number 94 secondary xxx no-reg both
label LL
description Lehrling Lehrnende
name Lehrling Lehrnende
mobility
snr xxx delay 1 timeout 30 cfwd-noan 98
snr ring-stop
call-forward busy 98
call-forward noan 98 timeout 20
ephone-dn 295 dual-line
number 93 secondary xxx no-reg both
label CM
description
name
snr xxx delay 1 timeout 30 cfwd-noan 98
snr ring-stop
call-forward busy 98
call-forward noan 98 timeout 10
ephone-dn 296 dual-line
number 92 secondary xxx no-reg both
label EE
description
name
mobility
call-forward busy 98
call-forward noan 98 timeout 20
ephone-dn 297 dual-line
number 91 secondary xxx no-reg both
label RS
description
name
mobility
snr xxx delay 1 timeout 30 cfwd-noan 98
snr ring-stop
call-forward busy 98
call-forward noan 98 timeout 10
ephone-dn 298
number 6.. no-reg primary
description ***CCA XFER TO VM EXTENSION***
call-forward all 98
ephone-dn 299
number A801.. no-reg primary
mwi off
ephone-dn 300
number A800.. no-reg primary
mwi on
ephone 1
device-security-mode none
mac-address A44C.11A0.B648
ephone-template 1
max-calls-per-button 2
username "xxx" password xxx
type 525G2
button 1:296 2:293 3m297 4m295
button 5m294
ephone 2
device-security-mode none
mac-address A44C.11A0.B566
ephone-template 1
max-calls-per-button 2
username "xxx" password xxx
type 525G2
button 1:297 2:293 3m296 4m295
button 5m294
ephone 3
device-security-mode none
mac-address A44C.11A0.B5C4
ephone-template 1
max-calls-per-button 2
username "xxx" password xxx
type 525G2
button 1:295 2:293 3m297 4m296
button 5m294
ephone 4
device-security-mode none
mac-address A44C.11A0.B67A
ephone-template 1
max-calls-per-button 2
username "xxx" password xxx
type 525G2
button 1:294 2:293 3m297 4m296
button 5m295
alias exec cca_voice_mode PBX
alias exec cca_vm_notification schedule from_time=00 to_time=24
alias exec clid-ALL_BRI ;1:0-4;1:0-9;1:0-9;1:1-9
alias exec clid-SIP ;1:1-9;1:1-9;1:1-9
banner login ^CCisco Configuration Assistant. Version: 3.2 (3). Fri Jul 04 13:18:33 CEST 2014^C
line con 0
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
transport preferred none
transport input all
line vty 5 100
transport preferred none
transport input all
ntp master
ntp server 91.240.0.5 prefer
enHi Patrick
I am working on this one as well. I have a UC560 with SIP Trunk provider Les.NET.
It was working fine until a few weeks ago when something changed on the provider end and broke it. My hunch it is something to do with the SIP REFER.
http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-express/91535-cme-sip-trunking-config.html
Here is an excerpt from the above page:
Call Transfer
When a call comes in on an SIP trunk to an SCCP Phone or CUE AutoAttendant (AA) and is transferred, the CME by default will send a SIP REFER message to the SP proxy. Most SP Proxy Servers do not support the REFER method. This needs to be configured in order to force the CME to hairpin the call:
Router(config)#voice service voip
Router(conf-voi-serv)#no supplementary-service sip refer
Figure 3 shows the behavior of the CME system with the REFER method disabled. -
Hello!
Now we use Cisco IP telephony based on Cisco CME. Cisco CME is installed on 2821 router with IOS C2800NM-ADVENTERPRISEK9-M, Version 12.4(24)T7. A SIP trunk is configured between CME router and telephony provider.
We plan to upgrade our telephone system and begin using Cisco CBE6000. I study the documentation and in "Cisco Business Edition Unified Communications and Collaboration Solutions for Small and Midsized Companies", I find that for SIP trunk to works in CBE6000 a Cisco Integrated Services Router with Cisco Unified Border Element is required. Or other quote from this document "Public switched telephone network (PSTN) connections using SIP is available through any Cisco Integrated Services Router voice gateway".
In this regard there is a question: what is the functions of this router when I make a trunk between CBE6000 and telephony provider SIP gateway and whether it is possible to use existing Cisco 2821 router as such router.
Thanks.Hi Ayodeji,
I too have a somewhat similar query.
We have UC560 running currently at our company, the UC560 is connected to an ISDN modem from the network provider. We are now upgrading to BE6000. To connect to the ISDN E1/T1 line, we've ordered Cisco 2921 with a E1/T1 VWIC card (VWIC3-2MFT-T1/E1) which will connect to BE6000 and internal LAN. I just wanted to know what would I need to configure on 2921?
Do I need to install CUBE or just configure it to connect to ISDN line?
Many thanks for any help.
regards, -
Calls from Sip Trunk to UC540 and then to CUE returned ** Service Unavailable**
Hi to all
i have something strange here and i need your assistance
Call Flow:
Sip trunk-->UC540--> CUE
When calls coming to UC540 from outside and then going to cue then we send back service unavailable.I made a translation and i sent directly the incoming calls to CUE
The same behavior is also if i send the calls to dummy number and then from there set forward all to voice mail.
Incoming voicemail is working fine
Incoming calls to phones also ok
Uc540: 8.6
CUE: 8.6.5
A number: 99999999
B number: 22777777
Voice Mail Number:111
Attached is the trace
i see that we hit the correct dial peers .
I have enable only trancoder since MTP is not register ( don't know why , but i don't think also that is necessary..
voice service voip
ip address trusted list
ipv4 172.16.80.0 255.255.255.0
ipv4 172.16.81.0 255.255.255.0
allow-connections sip to sip
supplementary-service h450.12
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
supplementary-service media-renegotiate
sip
no update-callerid
dial-peer voice 1000 voip
description **SIP TRUNK**
translation-profile incoming SIP-INCOMING
translation-profile outgoing SIP-OUTGOING
destination-pattern 9T
modem passthrough nse codec g711alaw
session protocol sipv2
session target sip-server
incoming called-number .T
voice-class codec 2
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
fax-relay ecm disable
no fax-relay sg3-to-g3
fax rate 9600
fax protocol pass-through g711alaw
no vad
dial-peer voice 2001 voip
description ** cue voicemail pilot number **
destination-pattern 111
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
incoming called-number 111
no voice-class sip outbound-proxy
dtmf-relay sip-notify
codec g711ulaw
no vad
Regards
chrysostomosHi
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 unassigned YES NVRAM up up
FastEthernet0/0.10 192.168.0.10 YES DHCP up up ----> For internet
FastEthernet0/0.20 10.151.5.130 YES NVRAM up up ------> For sip trunk
In0/0 10.1.10.2 YES unset up up --------> default gw for cue
Vlan1 unassigned YES unset up up
Vlan100 unassigned YES unset up up
Vlan200 unassigned YES unset up down
Vlan300 unassigned YES unset up down
NVI0 10.1.10.2 YES unset up up
BVI1 192.168.20.1 YES NVRAM up up
BVI100 10.1.1.1 YES NVRAM up up ---------> ip for cme
Loopback0 10.1.10.2 YES NVRAM up up ------> default gw for cue
dial-peer voice 2001 voip
description ** cue voicemail pilot number **
destination-pattern 111
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
incoming called-number 111
no voice-class sip outbound-proxy
voice-class sip bind control source-interface BVI100
voice-class sip bind media source-interface BVI100
dtmf-relay sip-notify
codec g711ulaw
no vad
interface FastEthernet0/0.10
description **FOR INTERNET**
encapsulation dot1Q 10
ip address dhcp
ip access-group 105 in
ip nat outside
ip inspect SDM_LOW out
ip virtual-reassembly in
interface FastEthernet0/0.20
description **FOR SIP TRUNK WITH ISP**
encapsulation dot1Q 20
ip address 10.151.5.130 255.255.255.240
ip route 10.1.10.1 255.255.255.255 Integrated-Service-Engine0/0
ping 10.1.10.1 source bvi100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.10.1, timeout is 2 seconds:
Packet sent with a source address of 10.1.1.1
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
I have bind the interface of cme ( 10.1.1.1) but the call fails again
Attached is the trace
Anything to advice? -
ADDING 9 TO MISS CALL SIP TRUNK
Hai i need to add 9 to miss call on call manager 10.5 using sip trunk to gateway
will the globalisation localisation affect unity connection and contact centre express.
any step by step guide available for sip trunk.I like to globalise now.. that way missed calls, recent calls etc can be placed from the phone. No need to place access codes before missed call phone numbers.
-
CME required CUBE license for ISP SIP Trunk
Hi,
We have IP telephony setup with CME 9.1 with 2921 ISRG2 router.
Client would like to take ISP SIP trunk.
Do we require CUBE license for the same.Because I tried in the 2851 router without the CUBE license and its working fine.
How I can check CUBE license installed my CME.
When I check license in CME I can see that UC K9 and IPBasek9 license are permanent.
Do this enough for the SIP trunk configuration.
Thanks & Regards
Nithin Louis.Just to add to George answer - CUBE licenses are somekind "honor" based right now which means you can configure everything and it will work but you need license paper for proving that you have adequate number of CUBE licenses for your system.
Maybe in future Cisco will improve this with option that you will need to install license and only then it will work - like many other licensing right now...
BR,
Dragan -
Why do we need MTP in the SIP trunk for CVP warm transfers
Hi All,
Why do we need to enable MTP in SIP trunk between CUCM and CVP for CVP based trasnfers???
Thanks in advance!!
Regards,
Thammaya Gupta K.I saw also in the CDR logs that the IP Phone media transport going to CUBE is in G711.And as well in the wireshark capture of the IP communicator that the CUCM invoke to use the g711 codec but as per ITSP logs they are now in the g729.
@ Jamie If I un-tick the MTP point required in SIP trunk will make the call leg from IP Phone to CUBE g729 (w/o hw resource), I have also tried to use g729 preferred originating codec, but still the IP Phone is using g711.
I have seen a documentation states:
" To configure G.729 codecs for use with a SIP trunk, you must use a hardware MTP or transcoder that supports the G.729 codec." - I read this on the CUCM help page under configuring SIP trunk setting.
Our ultimate goal is to use g729 without using HW MTP/ transcoder.
IP Phone ->CUCM SIP Trunk ->CUBE-> ITSP -
CUCM SIP Trunk Unable to find a device handler for the request received
I have a lab running CUCM 10.0 that has a SIP trunk to a VCS. Previously I was able to place and receive calls across the trunk, but now I can only place calls, not receive. I did recently upgrade to 10.5, but I really can't recall if it ever worked after the upgrade. The error I'm getting in CUCM is
Unable to route message, Cannot find the SIP Device with Name=192.1.1.61, Source Port=5060, IpAddress Type=0
This confuses me, because the destination IP/port of the VCS SIP trunk is 192.1.1.61:5060. The trunk on CUCM show as up and the Zone in VCS shows as up. What is going on?
Thanks, MikeI figured it out. Long story short, it was a port mismatch. When you configure Mobile Remote Access on the Expressway Core it creates a SIP trunk from Expressway to CUCM using port 5060. If you then create another SIP trunk from the same Expressway to CUCM for firewall traversal or external calling, you must use a different port. The port used for the zone in Expressway must match the SIP security profile used on the CUCM side SIP trunk. So I had created another SIP Security profile in CUCM with port 5062 for this purpose. However, the VCS in question that I was working with was only being used for FW traversal, so I used 5060 as the port on the VCS side, but I applied the SIP security profile that used 5062 on the CUCM side. That's why CUCM was throwing that "device not found" error. Once I changed the Security Profile to match the same port used on VCS (5060) all was well. Sorry for the long winded answer. Hope it helps someone else down the road.
-
Testing new sip trunk for an upgraded system....
Hey all,
Hoping I can get a quick direction on this.....
We are upgrading our call center servers and need to point a few test toll free numbers.
I have already created a test sip trunk....here's where it all gets muddy for me. What do I need to do to route 4 specific toll free numbers to hit this specific sip trunk instead of going to our current one?
Any docs and verbal guidance would be appreciated.
Thanks in advance all!Ok, so here's what i did....
I created the following >>> RG with new server as member>RL with the new RG as member>RP
We already have a RP of 5[1-9]XXX which matches the DNIS of the 4 toll free numbers we are using for this test, so I just went ahead and created an exact match RP of 59796. (I'll create the other 3 if I can get this to work)
Before I created all this, the call went to our sales dept like designed. After creating it, now I get a "this number has been disconnected" message. What did I miss? -
Best SIP trunk providers for Lync in UK
Hi,
Does anyone have any experience with SIP trunk providers in UK? can you suggest one that does not require me to purchase a MPLS line (like BT) or one that requires me to have a SBC on site. I have tried Gamma too but they are extremely slow in any kind of
response, any request can take over a month for them to complete.
P.S. please do not send me the link for approved SIP providers, i know about that, I am trying to see if anyone from UK has some good experience with a provider that I can utilize.
Thanks,This is most likely because the analogue phones are sending inband message in the progress indicator. We can see this from the ISDN logs, which is not present in the digital phones.
Oct 7 21:36:38.991: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x8213
Progress Ind i = 0x8582 - Destination address is non-ISDN
This is because usually analogue ports/devices always send 183 Session Progress.
Where are these analogue phones connected? On a cisco router? if they are then you can use the command below to get them to send alerting (180 ringing) to the sip provider.
voice call send-alert -
SIP Trunk for Legacy Nortel PBX
We have a legacy Nortel Meridian Option 11c, and about 400 digital sets. This is being fed by two PRI's from a big, old telecom whose name you would recognize if I told you. Our 3-year contract on the PRI's expired and our long distance went up overnight by an unbelievable percentage (completely outrageous and unsustainable). We have to get off of them right away.We're thinking that a SIP trunk service would be an economical way to bring down the costs; however the current system does not have capabilities to connect to a SIP trunk. There are two ways to address this: 1) a SIP-to-PRI gateway device (Digium, Adtran, etc.), or 2) get a whole new phone system.We have vendors trying to push us a to completely new phone system. We are not in a position to buy a new phone system. Maybe in a couple of years, but not now. Yes, I know Nortel...
This topic first appeared in the Spiceworks CommunityYou don't need H323 at all in this setup, man.
The Correct Setup Is:
TDM PBX ----PRI--->Cisco ISRG2 Gateway with PVDMs and VWIC2 or better ----SIP-----> SIPSP
This works like you have a PRI gateway from the PSTN to CUCM, except reversed. The VOIP call legs face your SIP SP, and the POTS call legs face the PBX.
I'd recommend against Q.SIG. I know a lot of people like it but each PBX vendor speaks a slightly different version and it gets messy. Just provision the whole thing as NI2 and make sure you are the network and clock source for the PBX (clock source internal on the controller and protocol-emulate network on the Serial x/x/x:23 interface).
Make sure your dial peers are set up correctly and this is easy as cake, man.
Let me know if you need any configuration assistance on this, I've done it like a thousand times.
Chuck
Maybe you are looking for
-
What can I try if the store's Advanced Search strikes out trying to find the song I want?
-
BPM : Receiver Determination Step
Hi, I was wondering why we need a Reciever determination step since on send step xi automatically find that there are multiple receiver and sends them accordingly to the different system as per reciever agreement. Is it that the receiver determinatio
-
Darwin/BSD startup error and second level error
I woke up this morning to find the world as I know it in disarray. My G5 was not booting to its normal screen but to the black ominous Darwin/BSD screen. I researched this awesome forum and found to login as single user mode (cntrl S) This led me to
-
Report Builder remove toolbar when running integrated report
Hi there, I am using Report Builder 3.0. I want to remove the toolbar (http://screencast.com/t/HDbGHZXz3vJa) when I am running some of my reports but not all of my integrated reports. Is this possible? Thanks in advance :)
-
Is there any update that I can implement for Lightroom 3 to allow me to process .ORF from EM-5?
This support is apparenly available for Lightroom 4. I have an Olympus OM-D EM-5.