Light static on DAT tape

I recently shot a band and used a DAT recording from the soundboard. during soundcheck i set my levels, recorded a bit and everything sounded perfect. during the bands set, the soundguy did something and now i'm getting a light static sound, but only on the highs...like feedback and some on vocals. i tried using the equalizer and it helped a bit, but it's still kinda noticable. is there anyway i can reduce the static or eliminate it without harming the quality of the recording. i use a sony tcd-d8 DAT recorder and my levels were set at about 10db or so. i'm still kinda new to recording live sound like that so any suggestions are greatly appreciated

You will probably want to experiment with a noise gate filter - but if you want to preserve the quality of the recording, you'll have to go easy on it or else your audio will sound muddled. You may only be able to remove the worst of it.
I've had some success using the Emagic filter that comes with Sountrack for noise gate. It takes some trial and error, and I suggest loading the Wikipedia site while you mess with it, so you can look up some of the terminology Anyway, click the little asterisks-looking button on the upper far right of the track properties area, above the volume value entry field and to the left of the reveal triangle for sound envelopes . That will bring up the filter window where you can add the Noise Gate.
There may be third party filters out there that are mean for this specifically. But the key is experimenting, because everybody's problem file is going to be different.

Similar Messages

In new iPad 4g, when sim card is not inserted, I can not find the enable 4g tap in the setting-cellular data tap, can some one please tell me if this is normal and if so, then when it appears, thanks

In new iPad 4g, when sim card is not inserted, I can not find the enable 4g tap in the setting-cellular data tap, can some one please tell me if this is normal and if so, then when it appears, thanks

If the SIM is out of your phone, find my phone needs a data connection, so could use wifi - IF in range of a wifi and one that it can join (ie. a known network or one that is wholly open so no login required). Your phone could also simple be turned off, so not findable, or it may have been restored (plugged into iTunes and restored as new) again, making it permanently unfindable. Honestly, for someone stealing an iPhone, this is likely the first thing they do - restore as new and it is theirs forever.
Find my iPhone is tied to the users iCloud account - the find function is part of the iCloud account's services and it communicates with the iCloud servers over a data connection - either wifi or 3G.
Have you set up your iCloud account on your replacement phone, and is it working properly on that phone?

STATIC "HTML Data Set Photo Gallery" with CAPTIONS

Because of search engines and validation I would really like to use the STATIC "HTML Data Set Photo Gallery" http://labs.adobe.com/technologies/spry/demos/gallery_pe/static/china.html.
But I definitely need captions for the Photos. I found possibilities to add them via XML, but not for the HTML-Version.
As far as I got I think I have to edit this function from "gallery_hds.js" and add some RegEx, to extract caption text.
function PhotosFilter(ds, row, rowIndex)
 var tnStr = row.thumbimg;
 if (tnStr)
 row.path = tnStr.replace(/.*<a[^>]*href="?([^"]*)"?.*/i, "$1");
 row.thumbpath = tnStr.replace(/.*<img[^>]*src="?([^"]*)"?.*/i, "$1");
 return row;
In the following rows within the html-document
<a href="../../gallery/galleries/paris/images/paris_02.jpg"><img src="../../gallery/galleries/paris/thumbnails/paris_02.jpg" alt="paris_02.jpg" /></a>
I would insert text before the closing span-tag (or before the closing a-tag?) - like so
<a href="../../gallery/galleries/paris/images/paris_02.jpg"><img src="../../gallery/galleries/paris/thumbnails/paris_02.jpg" alt="paris_02.jpg" /></a>Here is some HTML Text
This text must be extracted via RegEx - similar to the rows within the if-Statement of the upper mentioned function "PhotosFilter". But here my RegEx-knowledge is definitely to short!
Thank you very much in advance for any help or suggestion.
Angela Fengler

Because of search engines and validation I would really like to use the STATIC "HTML Data Set Photo Gallery" http://labs.adobe.com/technologies/spry/demos/gallery_pe/static/china.html.
But I definitely need captions for the Photos. I found possibilities to add them via XML, but not for the HTML-Version.
As far as I got I think I have to edit this function from "gallery_hds.js" and add some RegEx, to extract caption text.
function PhotosFilter(ds, row, rowIndex)
 var tnStr = row.thumbimg;
 if (tnStr)
 row.path = tnStr.replace(/.*<a[^>]*href="?([^"]*)"?.*/i, "$1");
 row.thumbpath = tnStr.replace(/.*<img[^>]*src="?([^"]*)"?.*/i, "$1");
 return row;
In the following rows within the html-document
<a href="../../gallery/galleries/paris/images/paris_02.jpg"><img src="../../gallery/galleries/paris/thumbnails/paris_02.jpg" alt="paris_02.jpg" /></a>
I would insert text before the closing span-tag (or before the closing a-tag?) - like so
<a href="../../gallery/galleries/paris/images/paris_02.jpg"><img src="../../gallery/galleries/paris/thumbnails/paris_02.jpg" alt="paris_02.jpg" /></a>Here is some HTML Text
This text must be extracted via RegEx - similar to the rows within the if-Statement of the upper mentioned function "PhotosFilter". But here my RegEx-knowledge is definitely to short!
Thank you very much in advance for any help or suggestion.
Angela Fengler

Is there any documentation which throws light on how data aggregation happens in data warehouse grooming? what algorithm exactly it follows in different aggregation type (raw, hourly, daily)?

Is there any documentation which throws light on how data aggregation happens in data warehouse grooming? what algorithm exactly it follows in different aggregation type (raw, hourly, daily)?
How exactly it picks up a specific data value during Hourly aggregations and Daily aggregations?As in How the value is chosen. Does it say averages out or simply picks value at the start of the hour/day or end of the hour/day ??

I'll try one more time. :)
Views in the operations console are derived from data in the operational database. This is always raw data, and typically does not go back more than 7 days.
Reports get data from the data warehouse. Unless you create a custom report that uses raw data, you will never see raw data in a report - Microsoft and probably all 3rd party vendors do not develop reports that fetch raw data.
Reports use aggregated data - hourly and daily. The data is aggregated by min, max, and avg sample for that particular aggregation. If it's hourly data, then you will see the min, max, and avg for that entire hour. Same goes for daily - you will see the
min, max, and avg data sample for that entire day.
And to try clarifying even more, the values you see plotted on the report are avg samples. If you drill into the performance detail report, then you can see the min, max, and avg samples, as well as standard deviation (which is calculated based on these
three values).
Jonathan Almquist | SCOMskills, LLC (http://scomskills.com)

Importing A-Dat tapes into Logic

I have lots of 8 –track Adat tapes of recording sessions that I’ve done for the last 10 years or so. The recording session were for various Jazz projects. I have rough mixes from those sessions that I’ve been able to listen to. But, I don’t have a A-Dat player. So the original A-Dat tapes have gone un-used for some time.
The thought occurred to me that maybe I can import the a-Dat tapes into Logic and mix and master them on my own. The thing is that I’m not totally sure of the “best” way to go about it.
At the moment, I am using a small Firebox interface. I suppose that I would need to get a larger 8track interface like maybe a Firepod? I would also need to buy a A-Dat machine. I’ve seen these on E-Bay for a couple of hundred. I would imagine that I would take each of the 8 A-Dat track to a separate input on the Firepod, create 8 new audio tracks in Logic, press record in Logic and press play on the A-Dat?
Is that it? Or is there a proper way to do this that I don’t know about?
Thanks,
Morris

Hi,
Yes you can definitely import your ADAT tapes into Logic.
Here's how to solve the issue:
1.You should buy an ADAT tape machine,make SURE you get the right one,as the newer one recorded at 20bit,and the older(blackface)only did 16bit.This part is crucial.I would probably recommend you get as newer an ADAT machine as possible,and look for low head hours too.
2.Buy an audio interface that supports the ADAT lightpipe format.Usually this can be from a cheap box to an expensive one.Just make SURE it does support the ADAT standard.
3.Buy 2 ADAT optical lightpipe cables long enought to connect the ADAT machine to your audio interface.You WILL need both cables to ensure correct digital audio synchronization.
4.You will need another interface,such as a Unitor8mkii or a Motu MTP/av USB model,in order to slave Logic to you ADAT machine via MMC protocol.Please refer to chapter 19 Synchronization page 605/619 of the Logic Pro reference manual to learn how to sync Logic to the ADAT.
5.Yes,you would be able to record ALL 8 ADAT channels at once,in one "pass".
Just make SURE you read the manual in step 4 thoroughly and test your setup BEFORE recording,to ensure you are doing it correctly.
Cheers

SCCM 2012 - Endpoint Protection Reporting only using static end date

I have created a subscription to the Endpoint Protection/Antimalware Activity Report built into SCCM2012/Endpoint Protection.
My problem is that I am having trouble getting the dates to work correctly. I want to have the report automaticlly emailed out every monday morning with the status from the last 7 days (i.e. since the last monday report).
However the subscription seems to want a static end date. That is, every monday when the report runs it gives me a status report from the exact same 7 days. Not the most recent 7 days.
How do I go about changing this so it is useful and that every monday it runs, the report it creates/sends is from the the last 7 days?

I hope this helps (I am still testing it) but I did this by:-
"Editing" the default report such as "Antimalware activity report".
To avoid corrupting this default report before you change anything select SaveAs and call it something like "Antimalware activity report
for the last 7 days".
Open Datasets, StartEndDates and replace the query with this for the last 7 days
"select DATEADD(day,datediff(day,0,GetDate())- 7,0) as StartDate, DATEADD(day,datediff(day,0,GetDate()),0) as EndDate"
Then open Parameters, StartDate and under General change it to "Hidden".
Then open Parameters, EndDate and under General change it to "Hidden".
Save and test
I had to set the "default value" on each parameter, per Lillonel:
StartDate : =DateAdd("d",-7,Globals!ExecutionTime)
EndDate : =Globals!ExecutionTime
It looks like it is using a 7 day window now.

What is the best software to record DAT tape to computer?

Hi guys,
I have some old DAT recording of my rock band from 1971-74. I want to transfer the DAT to my Macbook Pro retina. My plan would be to hit the "play" button on the DAT and record the whole tape to the MacBook Pro...and then go back, separate the songs I want to keep and add some EQ and compression (if I can figure out how that works ). I have the setup ready to go from a Behringer UCA222 from the DAT into USB on the MacBook Pro. I also plan to send the recording to my external thunderbolt HD. And I probably want to save the recordings at a higher quality and then to mp3.
What would you suggest would be the best software to use to transfer on a project like this?
I don't have Logic, and don't want to spend the $ for this project. I am looking at using GarageBand, but don't know if that eats up too much HD space and computer processing. I've read that Audacity might be an option, but not sure how the quality would compare to GarageBand.
Any other suggestions or comments would be really appreciated.
Thanks,
Bob

I use to face this issue every now and then (as a freelancer) when I use to cut on FCP7.
if the material is DV and was captured using Sony VEGAS, Premiere or Edius, the footage generally worked fine. You'll find most people will tell you to convert it regardless, however I found no issues working with them.
A problem you'll definitely face is HDV material. Most PC editing software write HDV in their own codec, which can't be read in FCP.
The only thing I can think of is to try converting HDV meaterial to QuickTime using something like MPEG Streamclip, or something similar.
Good luck

Apache+Tomcat access to static apache data from Tomcat

Hi,
Apache is in path /opt/apache
and tomcat is on /opt/apache/tomcat
I have to access to static data (/opt/apache/data) that is handled by my apache http server from my tomcat web application. Is there a way to do this in a clean way without doing things like this :
getServletCoontext().getRealPath(xxx) and doing some ../data manipulations
Thanks

I'm not completely sure I fully understand your problem.
I do not recommend opening sockets to your own WLS instance. That is a
recipe for deadlock.
Can you just include the static file in your response?
-- Rob
Yol. wrote:
We have a WebApplication which is running on a WebLogic Server 6.1.
The clients access to the application via an Apache hosted in another machine.
The Apache server redirects the requests to the server except the static files
which are served by the Apache Server.
Nevertheless, we have a few static resources that are not requested by the external
clients but are requested by the application in the WLS. The problem is that to
make this, it access the resource via the WLS, that is, via an url. That makes
the WLS open at least one socket. This cause that after a few time, there are
too many sockets in the machine opened in TIME-WAIT state.
For some reasons it is not possible to change the configuration of the sockets
in the server hosting the WLS.
We would like to access to this resources that are in the war of the WebApllication
without opening a socket.
Is it possible? Any ideas or suggestions?
Many many thanks in advance,
Yol.

Update of static LOV data display condition is not reflected in comp export

Hi team,
here is another possible little bug in 4.0.1.
I updated the conditional display for one entry in a static LOV.
This change is correctly reported in page 4000:4111 in the last updated column, but it is not reflected in the more general last updated column for the entire LOV component (page 4000:4110).
This affects also the component export where the updated static LOV does not appear in the first places if i sort the report by the most recently updated column (page 4000:688).
Flavio
http://oraclequirks.blogspot.com
http://www.yocoya.com

Suda,
1. I am currently on SBO 2005A PL 20, I've checked the issue of the "last purchase price" not being refreshed in the BOM on PL 36 .... Incidentally, the system behaves in the exact same fashion. I heard I can force the data refresh by using a format search, do you know how to do it?
2. If I don't use "last purchase price", instead using "My price list", thus I can use "Update parent items globally" to update the BOM. To achieve this goal, you suggest to use DTW, which I am still trying to figure out, meanwhile I've checked the SAP SDK and found the table ITT1 contains a column "PriceList" , which flags the certain price list being used. Can I reset this field to flag my price list without affecting data integrity?
Thanks...
Edited by: Rui Pereira on Apr 29, 2009 1:15 PM
Edited by: Paulo Calado on Jun 17, 2009 1:08 PM

Static Master data

Hi Experts,
i am given a requirement to create few infoobjects and also there is some master data given to me and they say its very much static for few master data objects , and client is asking to directly create in development system ,
is that our usull way of doing master data if it is static,
then if we transport the object to quality and production does this data get transported
Please guide me as what to do with this requirement
Thanks in advance
Nitya

Hi Nitya,
Data wont get transported to QA n PROD. You need to maintain the same or load the same in QA n PROD as well.
You can do one thing instead of loading manually why dont you use flat file load. by this you can load in QA n PROD as well.Its not best practice to maintain master data manually in PROD environment.
Regards
KP

IW38 Traffic Light for Custom Date field

Hi Experts,
I am trying use the Reference Field for Monitor. It has got 1. Priority, 2. Order/Start/End, 3. Scheduled Start/End.
We have created a custom date field as Original start/Finish dates. I want to create traffic light based on this date.
Can you please help me where and how to do this configuration. I have already searched the forum. But no help found.
Thanks,
Panneer

Panneer,
You can use Enhancement Spot ES_EAM_LIST_ENHANCEMENTS for this purpose (see SE18)
PeteA

Is there a way to serialize a live cycle for -- or apply a static time/date stamp?

I need to be able to either serialize the form -- assign a unique numeric or alpha numeric number to each form or apply a time and date stamp that is static (the existing date and time reflects the current time whenever the form is opened) Any suggestions?

I did a presentation on this topic for the Acrobat Users Group (BTW: another good forum for information). They recorded it. You should be able to get at the presentation here:
http://www.acrobatusers.com/events/1876/tech-talk-advanced-form-techniques-livecycle-desig ner
Paul

Importing audio from DAT tapes into FCP

Ok, so here's the connundrum. We've got 3 hours of VO we need to weed through and capture as AIF files onto our G5, so we can bring it into our FCP4.5HD project. I wanted to stay digital, so I got an ADSTech InstantMusic widget to interface the SPDIF with USB, but found out that it only had OPTICAL SPDIF, so then had to buy ANOTHER widget to convert coaxial audio to optical. Once that was all hooked up, I found out the hard way that the optical input on the ADSTech device wasn't working right. To troubleshoot, I hooked up a DVD player to rule out the coaxial to optical interface, but couldn't get the DVD's audio to recognize, despite the green light on the box. So to make sure the box wasn't just a POS, I hooked up the ANALOG audio inputs, and got monitorable audio, but the levels were EXTREMELY low, and at this point, I figgure that the ADSTech box is pretty much worthless.
Two questions, I suppose... One, has anyone else had this problem with the ADSTech box and been able to lick it? Two, does anyone have any other ideas as to how best to get this audio caputred without going through a digital to audio conversion?
Thanks much folks,
Kris

A reviewer at macHome had problems as well and does not recommend buying this device.
http://www.machome.com/reviews/0505/instantmusic.lasso

Voice Over, remove light static noise

Hi All,
I am sorry if there has already been a post on this.
I'm a very new user to any form of audio editing software.
I have some small voice over files that I captured on my camcorder... I have the smallest level of noise that I would like to remove. Is this possible adn if so how do I do it? I have normalised the file.
You can only really hear the noise when you turn the volume right up.
Thanks for any assistance.
Regards,
Katie

>Ozpeter is right, but I've found that it's more efficient to highlight your section of noise in edit view, then go to Effects > Restoration > Noise Reduction. In Noise Reduction, click Capture Noise Profile and then make other adjustments as necessary.
Hmm... that's not quite what
I'd call efficient!
Highlight selection, and hit Alt+N. That's all there is to capturing a noise profile - simple as that. After you've done that, either hit Ctrl+A and open NR, or, just open it and select all from within it.
And if you don't like keyboard shortcuts, it's always worth remembering that in Audition, you get a lot more options from using the right mouse button. And one of these, if you highlight a selection in EV, is to be able to capture your selection as a noise profile directly from there.

Best Practice for Using Static Data in PDPs or Project Plan

Hi There,
I want to make custom reports using PDPs & Project Plan data.
What is the Best Practice for using "Static/Random Data" (which is not available in MS Project 2013 columns) in PDPs & MS Project 2013?
Should I add that data in Custom Field (in MS Project 2013) or make PDPs?
Thanks,
EPM Consultant
Noman Sohail

Hi Dale,
I have a Project Level custom field "Supervisor Name" that is used for Project Information.
For the purpose of viewing that "Project Level custom field Data" in
Project views , I have made Task Level custom field
"SupName" and used Formula:
[SupName] = [Supervisor Name]
That shows Supervisor Name in Schedule.aspx
============
Question: I want that Project Level custom field "Supervisor Name" in
My Work views (Tasks.aspx).
The field is enabled in Task.aspx BUT Data is not present / blank column.
How can I get the data in "My Work views" ?
Noman Sohail

Light static on DAT tape

Similar Messages

Maybe you are looking for