Lightweight AP to Autonomous conversion without Controller

Dear Folks,
I do have 1131 LWAPP in home, i was wondering if i can convert to Autonomous . I read in the documentation, that only way is to use with controller. Is it true ? or can i convert without connecting to WLC .
SID

1) Go to your Computer and from the tool menu -> folder options ->uncheck the hide extensions for known file types option.
2) Download the IOS image ( you can get this ios image from cisco.com) on your desktop.
3) Rename the image into c1130-k9w7-tar.default
4) Give your computer Ethernet an address in the range 10.0.0.2 till
10.0.0.30
5) Run the tftp server on your computer.
    - Make sure that the directory of your tftp server is the desktop.
    - Specify the AP address on the tftp server if needed.
6) Connect the AP to the computer with Ethernet cable.
7) Remove the power from the AP.
8) Press and hold Mode button on the AP, and insert the power jacket in the AP.
9) Keep pressing on the Mode button for (20-30 seconds) until you see RED Led.
10) Wait until the image installed and all led lights return to green

Similar Messages

  • Is it possible to config AIR-CAP1602E-A-K9 without controller

    I purchased a preowned AIR-CAP1602E-A-K9 to setup at my home. I did not realize it needed a controller, and need to set it up to work on it's own. Is it possible? any assistance would be greatly appreciated.

    Hi Rendell,
    AIR-CAP1602E-A-K9, its a controller based 802.11a/g/n.
    This would need a controller to function.
    I think u can try to change from Lightweigh to Autonomous and then u can use these APs.(I never used 1602E ap).
    How to change Lightweight to Autonomous:
    Please check these:
    http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
    https://supportforums.cisco.com/docs/DOC-14960
    http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/
    Regards
    Dont forget to rate helpful posts.

  • Is it possible to do multiple ssids and encryptions on an autonomous AP without vlans?

    I got a customer who just has autonomous APs. They are upgrading from 1210s to 1262s. They are currently running a config that is wide open with no authentication or encryption and using a VPN tunnel on the wireless clients for security. They want to switch to using WPA2/PSK with the new APs. They have existing clients that have to continue to work during the upgrade to the new APs. They run 3 shifts so it is a 24 hr operation with no downtime. What I was thinking would be to configure the 1262 with multiple SSIDs, one with their existing settings and one with the new. Then I could swap the APs one at a time and it would only impact service for a short period of time while I was mounting the new AP. Then once all the new APs are installed I could transition the clients over to the new SSID and encryption then disable the old SSID once all the clients are switched over. I've done this before with a WLC but not with an autonomous APs. The only config examples I can find uses VLANs. This customer is not using VLANs. Is there anyway to use multiple SSIDs with different encryption on a single radio on an autonomous 1262 without VLANs?
    The site has about 30 APs and 100 clients. Yes I know a controller would be preferred for a site of this size but that is a question for sales and why they didn't see them a controller. I just get stuck with what they sell them.
    thanks

    Hi Don,
    Im afraid on the autonmous platform you can not map multiple WLANS to a single vlan.
    "Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
    ‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

  • Steps to convert access point from LightWeight mode to Autonomous mode

    I need steps to convert the following access point from Lightweight mode to Autonomous mode
    AIR-AP1242AG-E-K9
    Regards,
    Majid

    Hi Majid,
    The method is just hidden a little further down the doc that Scott linked (+5 points Scott :)
    Using a TFTP Server to Return to a Previous Release
    Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
    Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
    Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
    Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
    Step 3 On the PC where the TFTP server is located, perform these steps:
    a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
    b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.
    Step 4 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
    Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
    Step 6 Disconnect power from the access point.
    Step 7 Press and hold MODE while you reconnect power to the access point.
    Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
    Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
    Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.
    http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
    Hope this helps!
    Rob

  • How do I get to the start of a really long text message conversation without scrolling through them all? Thanks

    Hi. How do I get to the start of a really long text message conversation without having to scroll through and load earlier messages repeatedly?  Thanks

    click on the top of the screen (the top bar/clock sectionish).  Hope i helped

  • Is there a way to hide an iMessage conversation without deleting it?

    Is there a way to hide an iMessage conversation without deleting it?
    I recently went through a breakup and would like to not see my ex's face and messages every time I pull iMessage up, but I also don't want to delete them. I have the most up to date versions of iMessage on my Macbook Pro and iPhone 5C as of this post (10-5-14)

    Hi,
    iMessages account on the Mac (in the Messages app) stores the iMessages in a Chat.db item
    IF you dismiss a conversation from view  (mouse over it and use the x that appears) the chat.db will supply the "History" if and when you contact that person again.
    However it is worthwhile also creating a back up of some sort.
    As well as Time Machine it can also help to highlight the whole Chat (work from the most recent end to the "top" of the conversation to highlight it all.
    You can then Print and Save as PDF.
    You can back up your iPhone in iTunes.
    These can be used to Restore the iPhone back to that time.  (you do lose all new things added since the Backup was made.)
    There are various tools out there to extract info from iTunes Backups of iOS devices, which might help.
    Of course the Messages app on the Mac also has a Settings for Saving on close.  (it will Save if you dismiss the chat/Conversation and when the app is closed/Quit)
    Over and extended conversation or chat that lasts days or months each Session on the computer is Saved.
    Again you can dismiss the chat/conversation form view as you have saved versions (in parts) of the conversation.
    (You cannot Save a chat or conversation in Retrospect.)
    8:42 pm      Sunday; October 5, 2014
    ​  iMac 2.5Ghz i5 2011 (Mavericks 10.9)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb (Snow Leopard 10.6.8)
     Mac OS X (10.6.8),
     Couple of iPhones and an iPad

  • Conversion without the prompt to save

    Hello, prompt on the situation - in Adobe Acrobat XI Pro via master operations want to convert a lot of doc files to pdf. Opt for a folder with doc files starting the conversion process, but after the conversion of each document issued query "Save it or not" (attached screenshot). How do I make after converting one file passed to the next conversion without the prompt to save? To the process of creating pdf files was fully automated? Operation "Save" I added
    (please see screenshot)
    http://i62.tinypic.com/2ih095z.jpg
    p.s. Sorry, did not finish in the screenshot. "Do not need this question, we need to convert itself passed to the next file"

    Start Firefox in [[Safe Mode]] to check if one of the add-ons is causing the problem (switch to the DEFAULT theme: Tools > Add-ons > Appearance/Themes).
    * Don't make any changes on the Safe mode start window.
    See:
    * [[Troubleshooting extensions and themes]]
    * http://kb.mozillazine.org/Password_Manager (Troubleshooting)

  • My iphone 4 s has been losing service all day and freezing is anybody else having this prob its even to the point i cant hold a phone conversation without it cutting off.

    My iphone 4 s has been losing service all day and freezing is anybody else having this prob its even to the point i cant hold a phone conversation without it cutting off

    I had major issues with the iPhone 4s battery, however it’s resolved.
    The tech who set the phone up at the Apple store did so with little training.
    if you have a mobile me account. First go and move all your data to the cloud by going on your computer and logging in at me.com/move. The cloud has replaced mobile me, so there is no need for those two accounts
    Also make sure that for any of your email accounts you set them up to fetch, not push. My tech person set them all to have the email servers push data to the phone. The new iphone4s antenna is extremely strong so it will continually try to access stuff that is pushed–***** a lot of battery life doing this. It makes it worse if you have exchange 2010 accounts. Something about changes made to exchange really suck battery life from devices that access such accounts.
    turning of locator and the push notifications from facebook--they have a lot!

  • My iPhone 5s is showing Headphone is in use. I can hear conversation without using speaker or headphone

    I can't hear conversation without using headphone or speaker

    Hello there, Femierinfolami.
    The following Knowledge Base article offers up some good recommendations for troubleshooting your issue:
    iPhone: Microphone issues.
    http://support.apple.com/kb/ts5183
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • How to delete a single message within a conversation without deleting the entire message.

    Can a single message within a conversation be deleted without deleting the entire conversation?

    Hi,
    Your post is in iChat which is the app that preceded Messages.
    Your post is about Messages and from the sound of things and the iMessages account and posts  within that app and Account.
    You list an iOS device but have not made it clear if you want to do this on a Mac Version of the iOS version.
    Click and Hold the iMessages in Question. the iOS version should offer  you "Copy" and "More" .
    Chose the More option than then delete.
    You may have to right click on the Mac Version then chose Delete.
    9:37 PM      Thursday; December 4, 2014
    ​  iMac 2.5Ghz i5 2011 (Mavericks 10.9)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb (Snow Leopard 10.6.8)
     Mac OS X (10.6.8),
     Couple of iPhones and an iPad

  • Embed .mp3 in .pdf without controller?

    Whenever I embed an .mp3 in an interactive .pdf, a gray "controller" box appears as soon as the sound is triggered. And once the sound is triggered, the box cannot be made to go away without closing and reopening the pdf. I have no use at all for these things. I feel like I should be able to include interactive audio in a document without being forced to have these unhelpful controllers cluttering up my carefully-designed documents. (I mean, it's interactive audio; should there really be an obligatory visual component?)
    Am I missing something? There doesn't seem to be any way to "turn these things off." Any help would be appreciated!

    It could be some type of font incompatability between your PC and your Mac.  Most OTF's ( Open Type Fonts ) are compatable with both the PC and the Mac, but it may be a good idea to find out which font is suspect and replace it with a new, Mac version ( license ).  And, yes, for some reason, a font or two may not have been activated when you copied it over to your Mac.  I would think Distiller would be blind to font issues and RIP your file anyway, but again, if the font was never copied over or activated because of a license issue, then Distiller may just substitute the font(s).  It may be a good idea to match all of your previous PC fonts with new Mac versions.  And no, Distiller is not involved when you save-to-PDF in Ai.  The last time I checked, Distiller is / was a stand-alone application for creating PDF's.  Why not try using Distiller to see what happens?  You also have the option to Print > Save as PDF in Illustrator.  That's three ways to create a PDF: 1.) Use Acrobat's Distiller, 2.) Illustrator > Save As > Adobe PDF, 3. ) Illustrator > Print > Save as PDF.  Also, PC TTF's are not compatable on a Mac ( at least, that's the way I see it ).  Have you tried to print a desktop version of the Ai file to see if the font loads in your print driver?  If the printer skews the text that carries your font, then you know the font is definitely the problem.

  • CMYK to RGB conversion without 3rd party software?

    Does anyone know a way to use Automator to convert CMYK color mode images to RGB without having to have Photoshop or such installed? All Automator add ons I have seen thus far involve either Adobe products or other 3rd party image programs.
    Thanks!

    Hello again Ric,
    Thanks for your help. I would appreciate a bit of Applescript help. I have Automator back in the mix after playing around a bit.
    Yes, my associate who owns the website has neither PS, or GC. So if we can set up a way to automate this via email that would be great. I think I am actually about half way there, and I hope you will be kind enough to help me get the rest of the way.
    My machine is no longer the spunkiest, so I am using GC to do the color mode conversion, as it can launch, convert, and save the file in less than 1/4 the time Photoshop takes to launch. So yes, I'm doing this in a crazy fashion, but I have good reasons.
    This is my script thus far:
    using terms from application "Mail"
    on perform mail action with messages theMessages for rule theRule
    tell application "Mail"
    set numberOfMessages to count theMessages
    repeat with eachMessage in theMessages
    set theSubject to subject of eachMessage
    try
    set nameOfAttachment to the name of the first mail attachment of eachMessage
    (*if nameOfAttachment ends with ".torrent" then*)
    set filename to "Macintosh HD:Users:parr:Desktop:Alpha Images:•From Brett:" & nameOfAttachment
    save first mail attachment of eachMessage in filename
    tell application "GraphicConverter"
    activate
    open {alias filename}
    save window 1
    close window 1
    quit
    end tell
    tell application "Automator"
    execute "Alpha Convert"
    end tell
    end try
    end repeat
    end tell
    end perform mail action with messages
    end using terms from
    This works up until I call my Automator workflow. In my workflow I currently have the scale item and the convert to jpeg item.
    Question 1: How do we tell Automator what files to use as an input? Do I have to add a Get Selected or Get Specified Finder Items? Can I use the 'filename' variable from the above script?
    Once I have that down, any advice you can give on emailing it back would be great.
    Thanks again.
    QS2002 933 - Soon to be Macbook 2.0   Mac OS X (10.4)  

  • How can I delete a conversation without losing the...

    Can someone help me?
    Thanks
    Gabrielfross

    Hi,
    You can try SkypeX.  It's a small utility that can delete messages without deleting all conversations.  You can find it here:
    bryancockerham.com/skypex-delete-skype-messages.php

  • Inputing program change without controller attached.

    is there any way to record program changes in realtime without any keyboard/controller hooked up to my laptop. for example, when i want do this with notes, i use the caps lock keyboard.
    thanks in advance for your time.

    thanks for the info. do you know if there is a way to have the faders or buttons accessible on the main window in logic 8 or would i have to record their changes from within the environment?

  • Can I restore a deleted text conversation without having to restore my whole phone to that date? I backup using iCloud

    I deleted a text converstaion on my iPhone5 and would like to retrieve it. Can this be done without restoring the phone and losing current messages?

    Other people have already answered this sufficiently a couple times.
    Restoring from a backup is all or nothing.
    You can not pick apart a backup.
    There are programs that can do that for itunes but not for icloud.
    So if you have an icloud from when the conversatiion was still on device then you can restore from that backup
    (it will be a total restore, all or nothing)
    However if you do not have a backup from then or are not willing to restore everything that conversation is gone.

Maybe you are looking for

  • Name of .crl and .crt file missing from HTTP URL in certificate details

    Hello Everyone, I am in the process of building a 2-tier Windows Server 2012 R2 PKI. The CA name of both the offline standalone root CA and enterprise subordinate CA have spaces in it (we'll call the CA name, 'Test Lab Root CA' for point of reference

  • Having trouble with tablelaoutpanel and flowlayoutpanel.

    I'm trying to make this forms controls expand with the form. After playing with anchoring and autosizing and what not, I'm not having very good luck with it. I think this is going to require some serious hand holding. Dick Hutchings

  • SAP PM or MM Which will be better

    Hello Everyone. I m Yash From Guj. I had done B.E.(I.T.) And workign in IT industry as a Software engg. I want to do SAP ,My programming level is not so good so in Technical I choose either BI/ Basis.. But i heard in BI does not have a lot opening an

  • Questions re: missed calls iphone5

    Past few days (so far not today) have had numerous missed calls. No ring, just discover later that a call was missed. Caller tells me it either rang a few times then went to vm or sometimes immediately to vm. I want my iphone 5 to notify me and then

  • Automatic conversion of Preq into PO

    Hi All, Instead of having an MRP planner checking each p.req and to convert them manually in a PO, is there any possibility to an automatic process where, based on the vendor lead time, the p.req is automatically converted in a PO, released and sent