Line along "bottom" of image when using camera on iPhone 4

Hi all
So I have a brand new iPhone 4 and everything seems fine, except for an issue when taking pictures with the camera, which I have a sneaking suspicion is a hardware fault. I'm hoping not, but I don't hold out much hope...
So when I take pictures, I have a line parallel with the bottom (side with the home button) of the iPhone. This appears both in the preview image when taking a shot, and on the saved image. It does not show when shooting video, but I have noticed the image is zoomed in slightly when shooting video, and the line is not in this.
The line is approximately 1cm away from the edge of the screen. This is not a discoloration, like with the bonding agent, it looks like a line of pixels.
I have taken a picture, but can't see how to upload it on this forum. If it'll help, I'll upload elsewhere and link it.
Thanks in advance for any suggestions.

And also when I completely turn my iphone off it doesn't reboot when I hold the power button in and I had to do a soft reset to make it restart but even when I did that it wouldn't reboot and about 1 hour later when I tried it again it did the screen was white with nothing on it apart from a small oval in the middle of the screen showing my lock screen and it took 4 hours for it to sort itself out and then it started flickering :( :( please someone help what can I do??!!

Similar Messages

  • Picture appears white (cannot see the image) when using camera raw filter in photoshop cc

    I have a fresh install of Photoshop CC on my macbook.  I am running into an issue when editing an image in Photoshop cc and using the camera raw filter.  If I choose the camera raw filter camera raw opens up but all I see is white - the picture is not showing within the camera raw interface.  This happens whenever I am working on a layer and apply the camera raw filter.  The only time it works is when I do not have any layers but only the image as it comes directly from within camera raw - then it works fine.  I'm guessing there is something really basic I am missing but it is maddening!

    You are welcome.
    The Camera RAW filter will not work on an adjustment layer alone. Select the layer with the image and the adjustment layer and convert to a smart object to apply the Camera RAW filter to the image with the adjustment layer applied.

  • When using Camera raw with PS12 after editing, I cannot save my file in JPEG, only DNG

    When using Camera RAW after editing photo I can only save file as DNG, I want to save as JPEG. HOW??
    THANKS LLOYD

    BARBARA,Yes, you are so right, I was deceived by the eve button,  Just tried it and it WORKS GREAT-Thanks for the help.
    THANKS AGAIN AND HAVE A GOOD DAY Lloyd
          From: Barbara B. <[email protected]>
    To: Lloyd Bennett <[email protected]>
    Sent: Tuesday, January 13, 2015 11:46 AM
    Subject:  When using Camera raw with PS12 after editing, I cannot save my file in JPEG, only DNG
    When using Camera raw with PS12 after editing, I cannot save my file in JPEG, only DNG
    created by Barbara B. in Photoshop Elements - View the full discussionYou are being deceived by the Save button, like most people. That button is not the Save As button, really, but a link to the DNG converter. To save your raw file in an image format, click the Open button instead and then save in the format of your choice in the editor. If the reply above answers your question, please take a moment to mark this answer as correct by visiting: https://forums.adobe.com/message/7092207#7092207 and clicking ‘Correct’ below the answer Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: Please note that the Adobe Forums do not accept email attachments. If you want to embed an image in your message please visit the thread in the forum and click the camera icon: https://forums.adobe.com/message/7092207#7092207 To unsubscribe from this thread, please visit the message page at , click "Following" at the top right, & "Stop Following"  Start a new discussion in Photoshop Elements by email or at Adobe Community For more information about maintaining your forum email notifications please go to https://forums.adobe.com/thread/1516624.

  • How stop PS6 from removing the DPI value from an image when using "save for the web"?

    How stop PS6 from removing the DPI-value from an image when using "save for the web"?
    Example:
    - Open a tif image, that contains a dpi value (resolution).
    - Use the splice tool in PS6.
    - Export the slices with "Save for web", as gif-files.
    Then the dpi value is removed, the gif files has no dpi value (it's empty).
    How can we stop PS6 from removing the dpi value when using "save for web"?
    OR:
    When using the slice tool, how can we save the sliced pieces without PS removing the dpi value?

    you can make your art go a little bit over the bounds. or you can make sure your artboart and art edges align to pixels

  • AI CS6 vectors turn into embedded image when using clipping mask

    AI CS6 vectors turn into embedded image when using clipping mask, how to solve it?

    With the Clipping Mask selected go here

  • How to prevent email when using find my iphone

    Hi there,
    Am I the only that finds the email confirmations annoying when using find my iPhone?
    Is there any way to prevent these emails, or a preference somewhere to turn them off?

    Apple:
         Considering the threads here and on other Internet sites, this is clearly a safety issue.  As a parent who uses this feature on my children's phone - this feature should be optional.  Notifying the bad guy when you are searching for your phone/child is not an option.  Thank you.

  • I accidentaly clicked "remove" when using find my iphone...how do I log in when my iphone is not with me to find it?

    i was using "find my iphone" and when given the location it was an old location. A post read that the iphone was either turned off or the wifi was not being used. A remove or cancel  button appears with this message. I accidentally clicked cancel and now when trying to retrive information about the location of my device it says that I must refresh page or set up instructions. There must be a way to reinstate my account without my device physically present but I do not know how...can someone help me?

    What ever device you still have on had.  Go to settings - general - about - name - then the name.
    I have 4 devices 2 iphone and ipad - which I've name differently so I don't get confused when using find my iphone.

  • When using Find My iPhone, is it possible to hear live sound around the device?

    When using Find My iPhone app on the iPad2, is it possible to hear live sound around a device wham the "Play Sound" button is tapped?

    Yes.
    What do you hear?

  • No audio when using FaceTime on iPhone.

    No audio when using FaceTime on iPhone. The video works, but just static is heard during call. I have attempted multiple calls to another iphone and my mac. Should I send the phone in for repair?

    Hi Anne-Lill Holme,
    Thanks for visiting Apple Support Communities.
    If you are not being heard during FaceTime calls on your iPhone 6, I recommend starting with these troubleshooting tips:
    Restart your device.
    If using FaceTime over a Wi-Fi network, go to the steps to resolve Wi-Fi network issues.
    From:
    iOS: Troubleshooting FaceTime
    Next, I recommend testing your iPhone 6 microphone in other applications, such as Voice Memos. 
    If you cannot be heard on recordings in other apps, see this article for additional troubleshooting help:
    If your voice is too faint or sounds unclear using iPhone, or iPod touch
    Best Regards,
    Jeremy

  • Vertical lines when using camera

    Hi all,
    I'm having problems with when using my camera, I'm having vertical coloured lines / stripes.
    Do I need to replace my camera or can it be solved otherwise?
    Regards

    I think you'll have to replace the camera. I had a vertical yellow band on the left of my camera in low light, and they swapped the camera out at the Genius bar in about 15 minutes.

  • Thin horizontal black line at BOTTOM of page when scan on HP Officejet Pro 8600 Plus

    I owned an HP Officejet Pro 8500 and scanning was perfect.  I recently purchased an HP Officejet Pro 8600 Plus.
    When I scan from the HP 8600 auto document feeder, I get a thin (several pixel wide) black line along the bottom edge of the resulting scan.  This line will sometimes be slighly crooked or only appear across half the page, in which case it tends to get thicker toward the edge of the page).  I believe this line is an artifact from scanning the very bottom edge of the oroginal document.  I think it is showing where the bottom edge of the page was when scanned.  If the document is a little skewed, then the black line at the bottom will be a little crooked, probably following the edge of the page.  This problem is consistent, and repeatable.  It happens in both "Scan To E-mail" mode and "Scan To Network Folder" mode.
    When I scan from the flat bed, I get a very narrow black line along the very top edge of the resulting scan, but the bottom appears fine (although I've not tested this extensively).
    These thin black lines did not occur when scanning from the HP 8500.
    I am wondering if there is a setting to adjust this, or if it is a firmware difference between printers that needs debugging.
    This question was solved.
    View Solution.

    I find it interesting that the issue happens across both printers.  This is what leads me to believe this is something with the software/connection with the PC.  One thing I will note is that you mentioned above using Adobe Reader 10.1.6.  The latest version of Adobe Reader is 11.0.02.  I would advise removing your current version of Adobe Reader and install the latest version. 
    I am not sure if this will fix the issue as you mentioned the line comes across in jpeg and other scanning styles.  Do you possibly have another PC you could try setting up a connection with quickly and attempting a scan?  This would be another way to ensure if the issue is coming from the printer or a connection/software issue.
    I would like to make sure the issue is coming from the scanners on these printers before returning the printers as I would hate for you to get another model printer and the issue remain with this printer as well.  However, I will note that the Laserjet Pro 200 is a nice series printer from my experience.  I have used the Laserjet Pro 200 black and white only edition, the MFP, and the TopShot edition where I am located.
    -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
    I am not an HP employee.

  • Orange line along bottom of clip in event library?

    The last clip I imported has an orange line along the bottom of the clip in the event library. I can't locate anything in the help file or getting started pdf about what this is. Does anyone know?
    This may be related to the fact that it is the only clip that has gray thumbnails -- they display OK when I'm skimming the clip, but after the cursor leaves the clip the thumbnails revert to gray again. This is the only clip this happens to.

    An orange line at the bottom of a clip in the event window means that portion of the clip is being used in a project.

  • Get newest image when using IMAQdx grab

    Hi everone!
    I have a problem. I use IMAQdx grab.vi to capture image from camera usb. it has 30 fps. I want to get newest image, which camera acquired. but I realize that IMAQdx grab.vi copys sequent image out of buffer. I simulate a moving rectangle. then I use camera to positive object. I alway receive position of object from camera delay 3 frame.I expect it to delay 1 frame. I attached my program. I want to configure camera to grab the newest image.
    Thank in advance!
    Attachments:
    MAIN.vi ‏204 KB

    The cleanest way to accomplish what you are trying to do uses the low-level functions. The Get Image VI will automatically pull the next buffer available, but can also be configured to pull the most recently acquired buffer or any buffer of your choosing. You can see the function's context help for more details.
    Also, if you are unfamiliar with using the low-level functions there is a very good example in the example finder called "Low-Level Grab" in the IMAQdx section.
    Christopher S. | Applications Engineer
    Certified LabVIEW Developer
    "If in doubt... flat out." - Colin McRae

  • Weird Scrambled images when using Intel HD Graphics

    I recently bought a new 15" Macbook Pro and I have been seeing some really weird scrambled images when it is using the integrated graphics. I mostly notice it when switching to Top Sites in Safari or when using Spaces. Now, when I open a program to force the graphics to switch to the discrete 330M card (1Password triggers it, oddly enough), the images correct themselves within a second or two. I tried to take a screen grab using Grab, but that actually scrambles the image even more. Is anyone else seeing this, or is this a sign of a hardware failure?

    I also have the same problem, only different circumstances. I've noticed there are several websites that I can go to that yield this issue, and for me the fix was to go into the Energy Saver system preferences and uncheck the Automatic Graphics Switching box. An example of an issue I'm currently experiencing is:
    Visit http://www.macsimumnews.com/index.php/archive/applepatents_hint_at_final_pro_changes_and_or_new_media_presentationsoftw/
    then click on the Reader button and the Safari window background gets all mangled. Click on the reader button again and it all goes away. Now repeat with that system preference turned off and it won't do it anymore.
    Please advise if you can reproduce this. (Oh, this obviously is only for 2010 MacBook Pros that have that system preference option in the first place).

  • Workaround: SWVMS16 Crash when using Camera Search Function

    When using the camera search functionality, SWVMS16 may crash.  The issue is caused when non-camera UPnP devices on the network send out large packet sizes.  Upcoming video monitoring releases will fix this issue.
    Workaround: If the issue occurs, add your cameras manually to the SWVMS16.
    SWVMS16 v1.21 Release Notes posted online.
    http://www.cisco.com/en/US/docs/security/csbvsc/swvms16/release/notes/Release_Notes_VMS.pdf
    Attached file shows the error message and the steps to manually add cameras to the SWVMS16.

    Hi agschin and welcome to the RH forums. The hhactivex.dll
    file is not used by the search function so you can rule that our.
    Have you tried recompiling and seeing if the problem still happens?
    You can also start the Bug Hunter feature in RH - View > Output
    View and then select the Bug Hunter button - and see if that throws
    up any clues.

Maybe you are looking for

  • Anyone used a Firewire A/B switch with audio interfaces?

    I've got an RME FireFace 400 that I'd like to share between two boxes. I've heard horror stories about unplugging or pluggin in Firewire to (I guess?) live machines - where the interface or the Firewire port got zapped. Is this safe to do if. 1. Both

  • MMS app?

    Hi, Does anyone know of a MMS app that has the ability to add a file attachment to text messaging? Thanks, Jerry

  • Captivate 7 - installing via AAME really necessary?

    I purchased a volume license version of Captivate 7 through my employer, and have purchased CS6 through the same route in the past. I do most of my CS6 work at home (time-consuming...) and use the copy at work to coordinate progress with colleagues o

  • Measure mobiles processor speed

    Hello I am trying to find out how i can measure mobile phones processor speed with help of J2ME. Is there any algorithm that can be used to measure the computational speed? Is there any way to measure Java's virtual machine speed? I found source code

  • Hp Pavilion g6 Notebook PC A4A95UA#ABA

    I accidently tried to open a power point presentation with the windows media player, How do I change the settings back to open it through power point?