Line in Picture

I have a white line running the length of the TV. I assume the set was damaged by kids etc... However, I switched sets and the line is starting to appear on a brand new set. Is it possible this is something caused by verizon equipment?
If so, how to solve and then replace?
Thank you

Where on the TV are you seeing this line? Do you see the line on every channel or just some of them?

Similar Messages

Color Laser 2605dn Prints Lines on Pictures

Color Laser 2605dn Prints Lines on Pictures.
Normally all txt prints ok but I cannot get rid of the horizontal and vertical lines ( if the image prints vertical) on all images that it prints.
I rarely use this printer. I have gone under settings/print quality and calibrated but it does not fix the problem.
Please help.
Thank you.
JB

Looks like a high voltage power supply issue with the black only. Since the laser/scanner on this model uses 1 motor for 2 colors that would eliminate the laser/scanner. Repair by a repair shop may cost more than the printer. Only suggestion I can give to is do a google search for the service manual and download it. Look for instructions for the removal of the high voltage ps and remove it and then put it back in. There is always the possibility one of the connectors has become loose and is causing the issue. Good Luck.

Add a line to picture

hi!
i read coordiantes from a file.
after that i want to draw line after line, such as the coordinates. to a picture.
i can draw every line, but the lines which had been draw before are gone.
please help me:
Attachments:
View.zip ‏18 KB

Hello rauchi,
Have a look at this code, it is not from me, I found it a while ago on this forum ; whoever wrote it, well done !
I hope this will help you
When my feet touch the ground each morning the devil thinks "bloody hell... He's up again!"
Attachments:
Drawing.zip ‏255 KB

Photosmart C6380 lines in picture prints

I am having problems printing 4x6 photos on the 6380. Set settings to best picture printing and have black lines running vertically down the picture. Unable to figure out how to fix, any suggestions?

Hello there! Welcome to the forums @mrbovidar ,
I saw your post about how your scans are now quitting in the middle of a scan job, from your Photosmart C6380. I hope to help you out, and would like to start with a few steps and questions for you.
To see if the problem is hardware related, opposed to software related, try a few copies from the front panel of the unit and let me know if the copies also cancel during a copy job.
Regardless of the copy results, try a reset and ensure the printer is plugged in directly to the wall outlet, avoiding power bars and surge protectors. This ensures the printer is receiving full power, and I have personally witnessed this alone, fixing a scanning communication issue. It's worth a shot.
Reset:
Press the Power button to turn on the product.
With the product turned on, disconnect the power cord from the rear of the product.
Unplug the power cord from the wall outlet.
Wait at least 30 seconds.
Plug the power cord back into the wall outlet.
Reconnect the power cord to the rear of the product.
If the product does not turn on by itself, press the Power button to turn it on.
Try a scan again, and let me know what happens during the copies and scans.
Also, let me know:
Which OS you're running on your computer.
If the scanning will work to any other device.
If you have tried another USB cable.
I hope to hear back from you, have an awesome day
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

I use title line under picture to print info-all info has disappeared

HELP! I use my Iphone to record daily activities at my job site. It has been working beautifully (I thought) I import the pics into Iphoto 09 and since there are no books offered that arn't all cutesy. (Older versions had "Yearbook" which was perfect) I discovered that if I double clicked on the title line under each picture I could put in a brief description of each picture, this was even easier and faster than using the books and it printed out fine. I recently had need to go back three months to check a pic for some info and all info has disappeared in all pictures, (over a years worth of documentation up in smoke) just the time and date remain. is there anyway of recapturing this info? If not 09 is useless to me and I will need to go back to an earlier version. Evidently this info will only remain as long as the computer is not turned off (who knew??) Any advice would be appreciated. Mel

Welcome to the Apple Discussions. First try deleting the iPhoto preference file, com.apple.iPhoto.plist, that resides in your User/Library/Preferences folder, reboot and try the contact sheet again.
If that doesn't help, backup and launch iPhoto with the Command+Option keys depressed to rebuild the library. Select the last three options.
Click to view full size
Again, try the Contact sheet. The custom titles and/or descriptions are kept in the library's database file. Have you viewed the older files and their titles since upgrading to iPhoto 09? How did you do the upgrade to 09? If done wrong that can remove all the metadata.

Strange lines blur picture turning out weird

Hello
a while back i had this problem where pictures wher looking funny when blurred but never realy had an answer
this is what i am talking about http://imgur.com/cs7Fy7M
Now i took this with my phone because when i take a screenshot people say the picture looks fine ,
I have tried alot of things but i can't fix it
here is a picture of it as a ascreenshot http://imgur.com/5Yq7wDc
I realy want a fix for this as most of my pictures become crap when i try to make something nice in photoshop !
thx for any reply and i hope i can finally fix this
greets

Please post images directly on this Forum (with the camera icon).
In which bit depth do you work (Image > Mode > … Bits/Channel)?
Does turning off »Use Graphics Processor« in the Performance Preferences and restarting Photoshop have any bearing on the issue?

White line - No picture

I hafe an old Toshiba 35" color TV CX35E60 with nothing but white line across screen.
Ready to give away to someone who would repair it.
Need to know the part that is needed and cost of it.
Thanks.

Probably the thumbnails in your iPhoto library are corrupted.
Try to rebuild the thumbnails:
Hold down the option and command keys (⌥⌘) at the same time and double-click the iPhoto icon.
From the window that will pop up use the rebuild thumbnails option.
If you do not have acurrent backup of your iPhoto library, it would be safer to make a backup, before you try this.
Regards
Léonie

Why Horizontal Lines in IPhoto pictures only?

Just recently began getting horizontal lines in IPhoto pictures only. Does not occur anywhere else when printing with EpsonCX6400. Changed ink cartridges, did a nozzle check, Head Cleaning, & Head Alignment on printer but still get horizontal lines on pictures printed from IPhoto only. Other items printed such as, web pages, emails, etc do not have these horizontal lines. Any suggestions.?

No - contact Apple for a redo and/or refund - http://www.apple.com/support/photoservices/returns/
LN

PM QS 933 w/ ATI Radeon 9200 Card: Picture rolls vertical line on TV Output

Has anyone who uses an ATI Radeon 9200 Mac video card with s-video out ,
when connecting it to your TV, do you see vertical picture rolls?
I've tried installing Switch Res X to see if that would fix the issue,
however it only address Monitor and not TV resolution.
Is this a drawback of the card, or is there a way to tweak it so it
can display without the picture constantly rolling from bottom to top
the faded white line on picture?

The way I have it setup is thusly:
ATI Radeon 9200 Mac Card is set in PCI slot, no other monitor cards exist.
S-VHS little yellow adapter (S-VHS to RCA) plugged into S-VHS slot,
then three way ( Video, Stereo Audio) RCA cable is plugged into that
running directly into AUX RCA front ports of TV.
Picture Quality, Audio Quality is great. Color and Luminance is great.
Only problem is when picture plays from Mac to TV, a faint ghosted
( 10%- 15%) veritical white stripe rolls from top to bottom to
and then again.
Funny thing is...I inserted a DVD Recorder between the Mac and the TV to
see if I could record it so I could make a screen grab of the recording
to post here for everyone, but the recording shows NO VERTICAL LINE ROLL.
So my guess is that it is in the TV. I could try swapping out TVs,
but since all my TVs are analog, ( and 32") I don't and can't afford
to switch to an LCD of the same size right now, and if it is a bug
in the card's way of synching to a TV, esp. Analog, then it would repeat
the process.
I also looked on ATI/AMD's website, nothing in its' FAQ or Support DB.
I plan on trying to call them if I can't figure this out.

MacBook Pro Repeatedly Loads Purple & Teal Stripe, Gray, Light Blue, Bright Blue and Bright Blue Stripe Screens Instead of OS after Optical Drive Replacement by Apple (PICTURES INCLUDED)

17 inch March 26-29 (order date – shipping date) 2011 MacBook Pro, 256GB Solid State Drive, 2.3 GHz Quad-core Intel Core i7, 1 processer, 4 Cores, 256 KB L2 Cache per core, 8 MB L3 Cache, 8 GB Memory (8GB 1333MHZ DDR3 SDRAM - 2X4GB), AMD Radeon HD 6750M Video Card, Intel HD Graphics 3000 with 512 MB total of VRAM. 110 GBs of free/unused disk space remaining.
Full Specs are in subsequent post.
The issues described in the title continue even after I’ve reinstalled the operating system twice (Snow Leopard) and installed Mavericks (which is working fine and even faster). I’ve tried many commands to repair this.
If anyone has experienced any of the symptoms above or below, your advice and response will be much appreciated as well as marked. These are the details:
My Early 2011 MacBook Pro has had the typical blue screens, screen freezes and graphics issues since I bought it about three years ago but nothing like this and NEVER any load issues until about a month ago. That was when my superdrive replacement was put in.
Since then my MacBook Pro will go into hard freezes or kernel panics. Then I’ll have to power it down manually and power it up manually. It’ll then refuse to load the OS until after multiple tries. It started out just 2 or 3, then 4 or 5, then 6-12, then 20. Now it takes over 30 boots to load the OS. These boot issues also occur even if it doesn’t freeze, i.e.: when I shut it down or restart it naturally (via the Apple menu, etc.).
95% of the time it’ll load to a gray screen instead of the OS. 4% of the time it’ll load to a light blue screen. Then there are the others: the first time this happened it loaded to the striped purple and teal screen shown in the picture. This happened the next four times then intermittently for about 5 or so more times.
It also loaded gray flickering screens. Flickering screens also occurred right before it froze and had to be manually powered down and up. Then it began to load regular gray and light blue screens and all flickering screens stopped. And then bright blue screens a couple times intermittently for a few days, sometimes with lines. Sometimes it’ll load to a blank/black screen as well. I’d reset the NVRAM and SMC but it still continued, happening multiple times a day, each time taking more and more hard shut downs and hard power ons to finally load the OS.
Until I installed Mavericks, every time it finally loaded the OS Finder began indexing. After Mavericks this has occurred 95% of the time.
After talking to Apple Support they had me do a NVRAM and SMC reset again over the phone. The MacBook Pro refused to load the entire time we were on the phone. After the call it got worse. It froze over 6 times that day and at worse took over 30 boots to load the OS.
I finally had time to deal with it the next day when it froze again. After over 25 boots it loaded and I put in the Snow Leopard OS dvd and ran Disk Utility. I verified the hard drive and it said it was fine. Repaired the disk anyway and it gave this message at the end:
“Updating boot support partitions for volume required”.
Next I tried to start in safe mode and it just hung up for hours. Then started up in single mode and it loaded the OS. It then loaded normally for three times in a row. I reinstalled Snow Leopard. Everything loaded normally. I waited an hour or so and then I downloaded Mavericks. 5 or so hours later Mavericks was installed. Everything hardware wise was fine for a day and all software issues were easily fixable incompatibilities. My Mac was even faster with Mavericks. However, Photoshop did give a perhaps relevant message:
“Photoshop has encountered a problem with the display driver, and has temporarily disabled GPU enhancements. Check the video card manufacturer’s website for the latest software.
GPU enhancements can be enabled in the Performance panel of Preferences.”
(I have OpenGL enabled in Photoshop and it was already checked when this error occurred).
Two days ago I went to Disk Utility to repair permissions while logged in to a non-admin account. Verified and repaired the disk, then verified permissions. Everything fine. After repairing permissions however, it gave a weird error box:
"Unapproved caller, SecurityAgent may only be invoked by Apple software".
The box stayed “stuck” in the Disk Utility window. My MacBook Pro then failed to do anything. I manually powered it down and up. It loaded to a gray screen with the error message box again: "Unapproved caller, SecurityAgent may only be invoked by Apple software".
It then refused to load anything else but this message box on a gray screen even after rebooting it multiple times in safe, verbose and single modes and after resetting the NVRAM and SMC. I went online with an iPad and entered in the error and got some advice. I tried to run fsck and erase the /var/folders/ via single user mode but it still loaded to a gray screen with the error message. I just decided to skip to the end and Cmd-R loaded into recovery mode and reinstalled Mavericks again. That worked: the message has not appeared since.
Some people have said this error is related to a hard drive cable failure. I know that this cable was tampered with during the optical drive replacement procedures because I watched them do it.
Everything was fine for a day. Then yesterday my MacBook Pro froze while trying to open a VLC file. It took 12 boots to load the OS. I tried single mode once and verbose mode once. 10 times it loaded to gray screens, even in those mode. A Safe boot lead to a bright blue screen. Finally reset the SMC and it loaded on the 12th time.
Just five hours ago the same thing happened except it took over 30 boots to load the OS. Single, verbose and normal boots, NVRAM and SMC resets lead to gray screens. Safe boots lead to bright blue screens with and without lines (see pictures). Finally loaded on a normal boot.
I know I should have tried safe booting, verbose, single and recovery modes, disk utility, fsck and other command methods earlier this month but in the end, these methods have not solved the problem anymore than resetting the NVRAM or SMC.
There seems to be conclusive evidence that it’s a hardware problem, stemming from last month, the FIRST AND ONLY time my MacBook Pro was opened up. Maybe it’s the hard drive cable, but it could also be the graphics card and/or logic board (something that’s always been defective on this MacBook Pro, in my opinion). Many early 2011 MacBook Pro owners have given evidence to the latter possibility online.
The first time it started it seemed to stem from me using iPhoto and Photoshop a lot. I had both running continuously for about two weeks. This is another reason for suspecting the graphics card/logic board is at fault (in addition to three years of screen/graphics glitches). And since the card is soldered to the board and the board connected to the cable...I also have serious battery draining issues, something else that got bad after the Apple Superdrive repair. And the battery is connected to the board...
Also, since downloading Mavericks, windows from every app get blurry/fuzzy when I scroll or zoom in. I have read that this is happening to a lot of folks though for various reasons.
I guess it could always be the hard drive. I just don’t know. I’m taking it in to Apple, but can't right away because it’s not local. I know they’ll be able to run a test on the hard drive. I wanted to see if anyone else has had this problem (especially the purple and teal striped screen) before they start poking around, possibly creating another problem that goes beyond my Apple Care Plan allotment.

SPECS OF MY MACBOOK PRO:
Model Name: March 26-29 2011 MacBook Pro (order date – shipping date)
Model Identifier: MacBookPro8,3
Processor Name: Quad-core Intel Core i7
Processor Speed:    2.3 GHz
Number of Processors:    1
Total Number of Cores: 4
L2 Cache (per Core): 256 KB
L3 Cache: 8 MB
Memory: 8 GB Memory (8GB 1333MHZ DDR3 SDRAM - 2X4GB)
HARD DRIVE: 256GB Solid State Drive
DISPLAY: MBP 17" HR Antiglare WS Display
AMD Radeon HD 6750M:
Chipset Model: AMD Radeon HD 6750M
Type:    GPU
Bus: PCIe
PCIe Lane Width:    x8
VRAM (Total): 1024 MB
Vendor: ATI (0x1002)
Device ID: 0x6741
Revision ID: 0x0000
ROM Revision: 113-C0170L-573
gMux Version: 1.9.24
EFI Driver Version: 01.00.573
Intel HD Graphics 3000:
Chipset Model: Intel HD Graphics 3000
Type:    GPU
Bus: Built-In
VRAM (Total): 512 MB
Vendor: Intel (0x8086)
Device ID: 0x0126
Revision ID: 0x0009
gMux Version: 1.9.24
Displays
Color LCD:
Resolution: 1920 x 1200
Pixel Depth: 32-Bit Color (ARGB8888)
Main Display: Yes
Mirror: Off
Online: Yes
Built-In: Yes
Battery Information:
Model Information:
Serial Number:    C01111403GLDGKMAE
Manufacturer: DP
Device Name: bq20z451
Pack Lot Code:    0000
PCB Lot Code: 0000
Firmware Version: 0406
Hardware Revision: 0001
Cell Revision:    1102
Charge Information:
Charge Remaining (mAh): 4583
Fully Charged:    No
Charging: Yes
Full Charge Capacity (mAh): 7765
Health Information:
Cycle Count: 276
Condition: Normal
Battery Installed: Yes
Amperage (mA):    -4487
Voltage (mV): 11306
System Power Settings:
AC Power:
System Sleep Timer (Minutes):    15
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes):    15
Wake on AC Change: No
Wake on Clamshell Open: Yes
Wake on LAN: No
Current Power Source: Yes
Display Sleep Uses Dim: No
GPUSwitch: 2
Battery Power:
System Sleep Timer (Minutes):    15
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes):    5
Wake on AC Change: No
Wake on Clamshell Open: Yes
Display Sleep Uses Dim: No
GPUSwitch: 2
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed:    No
AC Charger Information:
Connected: Yes
ID:    0x0100
Wattage (W): 85
Revision: 0x0000
Family: 0x0085
Serial Number:    0x007ad8c5
Charging: Yes
Current operating system: 10.9.3 (Mavericks) ; Installed on 6/21/14
Previous operating system: 10.6.8 (Snow Leopard); Installed 4/4/11
        Reinstalled multiple times. Last reinstall: 6/21/14

Trouble recording a guitar line in.

Hey guys, I'll try to make this as short and detailed as possible. I plug my guitar into my computer using the Line In, using a ME-70 as a preamp, but the computer doesn't register any sound.
Let me try to explain how I'm setting it up:
-My guitar is connected to the 'guitar in' on my ME-70
-I use a 1/4" to 1/8" converter on the 'Rec Out' jack in the ME-70 to connect to the line in on my computer.
-I turn the preamp on my ME-70 on.
-Go to System Preferences/sound, use the input audio as Line in
Pictures:
[IMG]http://i253.photobucket.com/albums/hh74/mexicoxx93/Picture2-8.jpg[/IMG]
[IMG]http://i253.photobucket.com/albums/hh74/mexicoxx93/Picture5-1.png[/IMG]
I checked, made sure all the volumes were on, and everything was plugged in properly. however, no matter how hard I strum, or what I put the volumes at, there is no response in the input level. Every cable functions perfectly, and when I plug headphones into the Rec Out jack it sounds great. what can I be missing?
thanks for your help.

I am also having trouble getting my guitar to show up in Garageband. I have followed every tutorial I can find online (they all say the same things anyways). I set computer audio preferences and GB preferences to line-in, and experimented with mono 1, mono 2, and stereo 1/2 line in sources in GB. No love from any of them. No sound at all. My guitar has active pickups and all cables work elsewhere. The line-in does show a bit of input when unplugging the cable from the computer so the input isn't dead.
Any help would be awesome.

Export only of developped pictures

Hi, I am a beginner in Lightroom 4.3.
I loaded some folders with my pictures. In Lightroom I developed some of it, others I did not.
Now I want to export only those pictures which I developed. I know, I can manually select at the bottom line all pictures showing a +/- sign and the export them. This is quite a lot of work with my 800 pictures.
Is it possible to tell Lightroom that it just selects and exports the developed pictures?

Ahhhh, I was scratching my head over that one (trying to provide answer).
My thought was to simply filter on the appropriate attribute or metadata, but a criterion of "has adjustments" is not available for filtering (though it is for Smart Collections). I wonder why Lightroom's filter criteria aren't the same as for Smart Collections?   An oversight?
Phil

Picture "slides" and keeps scrolling after I stop

When I use the touch pad and I scroll something on-line, the picture stops as it should.
After a couple of seconds the screen moves a bit as if I am scrolling some more, then moves again, then sometimes again!
What the...?
Any ideas?
Thanks,
Mike

More likely it is a hardware defect.
Have you restarted your phone?
If so, and the issue has persisted, backup your phone and restore it from a backup, then restore as new.
If neither of those resolves the issue, make an appointment at an Apple store near you and have a Genius examine it as it's most likely a hardware failure.
~Lyssa

Are we going to get the ability to fade or make photos transparent again? This was my most used Picture Frame application for the teaching slides I create.

Even Powerpoint has this feature. Why would Apple dum down this previously powerful piece of software that made creating soft teaching slides so much fun?

I just dragged in an image from the desktop (using the Black theme) and, in the pane over to the right, it shows "Border" as "No Border". I click on that and I get to choose "Line" or "Picture Frame". Is Picture Frame what you're looking for?
Additionally, the "ragged edges" is there, too. Change to the Renaissance theme, set an image to have ragged edges, swich back to the theme you want to use, then, with that object selected, under "Styles" add this to your list of styles by clicking the PLUS sign.

Dynamic Picture Displaying in the Group Footer Section

Hi all,
I am building a sales quotation layout for SBO in crystal 2008.
The layout has only one group. The first line in each group in considered to be a slaes tree father.
For every group i need to display the picture of the "father" in the group footer (one picture for every group).
I get up to the stage when for each line in the detailes section i have a picture, but for all the lines other then the "father" line the picture is supressed.
My problem is moving the displayed fahter picture from the detailes section to the group footer section. Every time i copy the picture field to the group footer nothing is displayed.
Any idea?
Thanks,
Udi

A group footer will dis[lay contents of the last record. You need to sort records to ensure that the last record contains link to your dynamic image.
Ian

Line in Picture

Similar Messages

Maybe you are looking for