Line-in port not showing in sound preferences
On my G5 in system preferences/sound/input, "audio line-in port" doesn't appear. Only "internal microphone" is listed. Anyone seen this before? Thanks.
In case anyone viewing my question has the same issue, here is the solution I discovered:
Go to Applications/Utilities/Audio MIDI Setup
Under Audio Input/Source choose "Line In"
Good luck!
Similar Messages
-
JHeadstart not showing in Tools/Preferences
JHeadstart not showing in Tools/Preferences.
I have done exact as in instructions.:
Unzip JHeadstart10.1.2.0.x.zip (using folder names) to a folder of your choice, >>for example C:\JHeadstart (in the next steps referred to as <JHeadstartHome>). I have unzipped to c:\case\jheadstart
Find out in which folder JDeveloper 10.1.2 is installed (in the next steps
referred >>>to as <JDeveloperHome>).
In <JHeadstartHome>\config\jdevaddins you will find a number of JAR files,
which need to be installed as plug-ins for JDeveloper. Create a new
directory <JDeveloper_Home>\jdev\lib\ext\jheadstart and copy the JAR files
to that directory: You have now extended the JDeveloper 10g IDE with
JHeadstart specific functionality! My jdev directory is:
C:\jdev_extract\jdev\
I have created a directory: C:\jdev_extract\jdev\lib\ext\jheadstart
If you want to be able to use JHeadstart Designer Generator: in
<JHeadstartHome>\config\jdevaddins you will also find a file named
migration.xml. This file must be copied to the system directory of
JDeveloper, for example: <JDeveloperHome>\jdev\system10.1.2.0.0.1811.
The exact name of this directory depends on the build number of JDeveloper. There was no such directory I created a directory called:
C:\jdev_extract\jdev\system10.1.3.36.73
Because I have JDev version 10.1.3.36.73 copy the *.xml in their.
I have tried all other "extensions" name like directories and copy the
migration.xml in their as well. Still did not show under
Tools/migration
As the last step, we have to tell the plug-ins where the JHeadstart Home is. Start JDeveloper 10.1.2, go to the menu option Tools - Preferences, select the category "JHeadstart Settings" and enter the JHeadstart Home. It should report a valid JHeadstart Home and show the version and build number.This is probably better off posted in the JHeadstart forum but from your post you seem to be trying to use JDev 10.1.3 with JHeadstart as far as I'm aware a 10.1.3 compatible version of JHeadstart has not yet been released and you must therefore use JDeveloper 10.1.2 if you want to use JHeadstart.
Regards,
Lisa -
PE12 just installed, but Organizer share preference for emailing photos does not show any email preferences except the default Adobe. Have Visa with Windows Mail. Previous PE worked OK. How to resolve?
Please post Photoshop Elements related queries over at
http://forums.adobe.com/community/photoshop_elements -
Tones checkbox not showing up in preferences popup.
Tones checkbox not showing up in preferences popup along with the other checkboxes in itunes 12.0.1, please help me i am terrified.!!!
I am now attempting to "repair" my Adobe Acrobat installation to see if this might fix the issue.... I did this by opening Adobe Acrobat X1 Pro > Help >Repair ....Installation... I will let you know how it goes..
-
Line-in port not working with powered microphone
I'm not sure if this is an issue of me not understanding how line-in ports work or if there is actually something wrong with the line-in port/jack. So, I have a Sony microphone that is powered by one AA battery. The microphone has no problems because I can plug it in to my voice recorder and it works fine. However, when I plug it in to the line-in port of my PB, the PB does not pick up any sound. And yes, I have made sure that in the Sound preferences, I selected input source as "Line-in."
So, does this mean there is something wrong with the port, or does it mean I need to plug my powered microphone into an amplifier which plugs into the PB or....?
Thanks!
ConalHi Conal
There's probably nothing wrong with your line-in port - it's just that you've discovered the difference between "line level" signals and "mic level" signals! To put it simply, the output from a microphone (whether it operates on battery power or not) is far too low for a line level input to recognise - hence the reason you are not picking up sound on the PB. (Your voice recorder will be picking up sound because it's operating at mic-level).
The only way around this is to plug your mic into some form of pre-amp and then plug the line level output of the pre-amp into your PB. Personally I use a Tascam US-122 audio/midi interface and run the signals into the PB on USB. Works extremely well but I'm sure you'll be able to find a cheaper alteranative with a little bit of searching.
Hope this helps.
Bob
PowerBook G4 Mac OS X (10.4.6) 1.5GHz; 1 Gig RAM
PowerBook G4 Mac OS X (10.4.4) 1.5GHz; 1 Gig RAM -
Line in port not working?
I've bought a usb web cam and, with the help of "ichatusbcam", can now see a video picture in iChatAv. The web cam also has a in built microphone with a jack plug that goes into the line-in port in my MDD. However when I select the line in port in sound prefs I can't seem to get any sound. There is no flicker of movement that shows that sound is being received. If I plug in my usb microphone and select that then no problem - I can see the prefs pane showing sound input.
Any ideas or does it suggest that the in-built mic isn't working?
DaveIt "sounds" like you might need a preamp for the mic to bring up the input levels to line-in requirements.
Regards, -
Thunderbolt port not showing connected device
I'm trying to use my 2d iMac 27" as a second monitor. I have the two iMac's connected via thunderbolt ports systems do not show any devices connected to either port.
Also, CMD F2 function (Target Display Mode) is not working.
Has anyone else this problem?
ThanksThanks dastoelk & Russ,
That definitly sounds like the issue, but the only thing new on the drive since the last time I opened FCPX is some new P2 media that's buried in the "PROJECTS" folder and some NEFs from a school play I recently filmed, in the "Greater Tuna" folder. But I have other P2 media and NEFs on this drive that have been on it for a while. Also, forget to mention, runnig FCPX 10.0.9 -
LACP using 2x 10G ports not showing 20G?
I currently have etherchannel configured to 2x 10g ports.
Cat_6509#sh run int ten8/1
Building configuration...
Current configuration : 156 bytes
interface TenGigabitEthernet8/1
switchport
switchport mode trunk
channel-group 42 mode desirable
end
Cat_6509#sh run int ten9/1
Building configuration...
Current configuration : 156 bytes
interface TenGigabitEthernet9/1
switchport
switchport mode trunk
channel-group 42 mode desirable
end
Cat_6509#
Cat_6509#sh int t8/1
TenGigabitEthernet8/1 is up, line protocol is up (connected)
Hardware is C6k 10000Mb 802.3, address is fc99.4736.a2f0 (bia fc99.4736.a2f0)
Description: 10 Gig GEC to MADDC (Spanned VLANS)
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 5/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 10Gb/s
Cat_6509#sh int t9/1
TenGigabitEthernet9/1 is up, line protocol is up (connected)
Hardware is C6k 10000Mb 802.3, address is fc99.4736.a238 (bia fc99.4736.a238)
Description: 10 Gig GEC to MADDC (Spanned VLANS)
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 8/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 10Gb/s
Cat_6509#sh int po42
Port-channel42 is up, line protocol is up (connected)
Hardware is EtherChannel, address is fc99.4736.a2f0 (bia fc99.4736.a2f0)
Description: 10 Gig GEC to MADDC (Spanned VLANS)
MTU 1500 bytes, BW 20000000 Kbit, DLY 10 usec,
reliability 255/255, txload 7/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 10Gb/s <<<<<<<<<<<<<<<<<<<<<<< Should this be 20GB if the ports are bundled?
Cat_6509#show etherchannel 42 summary
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use N - not in use, no aggregation
f - failed to allocate aggregator
M - not in use, no aggregation due to minimum links not met
m - not in use, port not aggregated due to minimum links not met
u - unsuitable for bundling
d - default port
w - waiting to be aggregated
Number of channel-groups in use: 28
Number of aggregators: 28
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
42 Po42(SU) PAgP Te8/1(P) Te9/1(P)
Last applied Hash Distribution Algorithm: Fixed
Cat_6509#
Thanks
STHi WannaB
Oops you are right the configuration is in PagP. However I have another port channel from the 7706 to Fabric Interconnect which is configured as LACP that is still operating on 10G.
ethernet# show int po30
port-channel30 is up
admin state is up
Hardware: Port-Channel, address: 8480.2da5.c36c (bia 8480.2da5.c36c)
Description: UCS Fabric Interconnect A
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, medium is broadcast
Port mode is trunk
full-duplex, 10 Gb/s
ethernet# show port-channel summary
Flags: D - Down P - Up in port-channel (members)
I - Individual H - Hot-standby (LACP only)
s - Suspended r - Module-removed
S - Switched R - Routed
U - Up (port-channel)
M - Not in use. Min-links not met
Group Port- Type Protocol Member Ports
Channel
1 Po1(SD) Eth NONE --
2 Po2(SD) Eth NONE --
3 Po3(SU) Eth LACP Eth1/2(P) Eth2/2(P)
30 Po30(SU) Eth LACP Eth1/5(P) Eth2/5(D)
ethernet# sh run int eth1/5
!Command: show running-config interface Ethernet1/5
!Time: Thu Dec 11 02:43:46 2014
version 6.2(8a)
interface Ethernet1/5
description UCS Fabric Interconnect A
switchport
switchport mode trunk
channel-group 30 mode active
no shutdown
ethernet# sh run int eth2/5
!Command: show running-config interface Ethernet2/5
!Time: Thu Dec 11 02:43:48 2014
version 6.2(8a)
interface Ethernet2/5
description UCS Fabric Interconnect A
switchport
switchport mode trunk
channel-group 30 mode active
no shutdown
ethernet# -
Does not retain system sound preference settings
I use a Tascam US 1800 audio I/O with my Mac Pro, but I have to reset the System Preferences to the US 1800 every time I restart the computer. The computer defaults to Line In and Line Out.
I thought perhaps there was something wrong with the US 1800, so I tested it with my MacBook Pro and that computer retains the Sound preferences to the US 1800 when shut down and restarted. So it seems like the issue is with the Mac Pro.
Does anyone have an idea what may be causing this and how to remedy it?
Thanks!
dmThe permissions are totally wrong. It looks like someone has intentionally changed them.
First, since I don't know what other damage has been done, you should at the very least back up all data and then run Repair Permissions in Disk Utility. That action may fix some (not all) other files with wrong permissions, but it wont fix this one.
If you have more than one user account, you must be logged in as an administrator to carry out these instructions.
Triple-click anywhere in the line below to select it:
sudo chown 202:202 /L*/P*/A*/*.audio.*.plist; sudo chmod -N $_
Copy the selected text to the Clipboard (command-C).
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V). You'll be prompted for your login password, which won't be displayed when you type it. If you don’t have a login password, you’ll need to set one before you can run the command. You may get a one-time warning not to screw up. Confirm. You don't need to post the warning. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
Quit Terminal and reboot. -
Line items are not showing in fbl1n/fk10n
hello all,
Again i needs your help. this time i am not able to see the line items in fbl1n and fk10n. system shows 360 line items are displayed but no line item are showing in screen.In fk10n i am just able to see the period wise balance. but line item not showing. this issue is only with my 5 vendor. in case of other vendor, i am able to see as i wish.
please suggest me how to solve it.
regards
konishkoHi,
check the Reconciliation of that vendor.for that recon account line display should be selected.
For other vendors, reconciliation account is with line item display .selected. That might be the reason to show line items for remaining items.
check GL master of Recon acccount. -
CJI5 commitment line item report not showing po gross value
Dear All,
system is showing only net value in CJI5 report, actaully gross value of po must be reflected in CJI5 report and this happening in all po's like material, service's etc. example is as follows.
Example:
po net value: 1000
st 10%: 100
po gross value : 1100 (inclusive of all taxes, ed, disc. etc)
what could be the reason for not showing po gross value in commitment line item report.
Thanks & Regards,
SandeepHi,
As far as i know the commitment report will never show you the value that is inclusive of taxes. It will only show the net value of the PO.
I just tried a scenario in my system by creating a PO for a net value of 3000 GBP and based on the tax code i entered system calculated a tax of 525 GBP. However when i check CJI5 report it shows only 3000 GBP as commitment and not 3525 GBP. This is how the standard system behaves, i believe. You can cross check this in the table COOI. The COOI table also shows the net value of the PO and does not include the tax amount in commitment.
Regards,
Gokul -
Tax Line items are not showing seperately as per exp in FB60
Hi,
In FB60, I have booked the two expenses with tax code separately. While simulating the entry the tax lines are not showing separately as per expenses. For example:
Suppose my tax code = AB which is equal to 10% maintained in FTXP.
At present entry is coming as follows through FB60 is:
Debit Postage expenses 500 tax code AB
Debit Stationery expenses 400 tax code AB
Debit Tax 100
Credit Vendor 1000
But we need the entry is follows
Debit Postage expenses 500 tax code AB
Debit Stationery expenses 400 tax code AB
Debit Tax 50
Debit Tax 40
Credit Vendor 1000
But I change the tax code for second line AB to XY then calculation of tax entries shows separately according to expenses.
Please let me know where did I do the mistake in configu2026u2026..
Regards,
BabjeeHi!
Normally, all amounts being posted to the same GL Account and determined from the same tax code as automatically derived, will generate one common auto-generated line item. This is because tax reporting is usually based on tax code (external/tax reporting) and or GL account (internal/financial reporting).
In your first case since the tax code used for both line is the tax code was the same, it would be posting to the same GL Account - hence a common line item got auto-generated.
Check the Account Key and Assigned GL Accounts in T.Code FTXP. Additionally, check the Condition Type set-up (identified from FTXP) in T.Code SPRO / from menu IMG node Check Calculation Procedure.
Regards,
Ruchi -
What are criteria of F-44 to show line item or not show?
Hello all,
I had reversed mm doc (from migo) with mr8m then I used f-44 for clear vendor account.
The fi doc that occured had no line item, please tell me how to know what criteria of situation that show or not show line item in fi document.
Thanks for advance,
FonHi,
I have the similar case but opposite of that. When I use F-44 to clear vendor line items, it generates line itmes but I dont want system to generate it.
Kindly let me know the setting or criteria for the same.
Regards,
Niraj -
JDI plug-in not showing in NWDS preference
Hello
I have installed NWDS 7.11 Latest NWDS release and post steps also done.
Help -> Software updates -> Find and Install and Choose Search for updates of the additional installed features.
But JDI (Development Infrastructure) plug-in not showing in preference.
Please let me know how to connect from NWDS to SLD or how to install JDI plug-in?
Edited by: Rahul Mathur on Jan 26, 2012 12:32 AMHi,
I assume you refer to perspectives (like webdynpro, development infrastructure, etc) which are not available in your NWDS even after completely updating it via the update site.
If this is the case then check this note which among other also covers what to do if you face the problem of missing perspectives.
please have a look at this note:
#1566977 - NWDS on Windows 7
(http://service.sap.com/sap/support/notes/1566977)
Best Regards,
Ervin -
Purchased Ringtones not showing in Sounds folder
I have purchased a couple of ringtones from itunes but they are not showing up in my Settings\Sounds\Ringtone folder.
How does a person get them into that folder or have the iphone 4s recognize where they are so access can be gained.
Currently they can be seen in my Music app and when my phone is connected to my iMac I can see them in Devices \ iphone \ purchased area.
ThanksCheck to be sure they are really ringtones and not just music files that can be converted to ringtones. To check, right-click on the files in iTunes, select Get Info, on the Summary tab they must say Kind: Ringtone. If the don't, follow the steps shown in this video to convert them to ringtones, then sync them to your phone: http://cnettv.cnet.com/create-free-ringtones-itunes-10/9742-1_53-50093086.html.
Maybe you are looking for
-
I tried genius on iPad and I get a black box
So I tried turning on the genius on the iPad and as soon as I turned it on it gave me a black box about the size of the terms and condition thing then I can't download any apps or even move it form the feature screen Any one pls help me with this pro
-
Is iweb09 available on server osx 10.8.4?
is iweb09 available on server osx 10.8.4?
-
I recently was given a new ipod and today tried to sync my music to from my itunes (my last ipod finally packed up a few months ago). When I started to copy my music, only about 1/3 of has gone onto my ipod and I got a message saying 'ATTEMPTING TO C
-
How to download itunes on windows rt surface tablet
is there any way to download itunes on a window rt surace tabletg?
-
Process on value request for table control
I have 10 rows in a table control,when a F4 for a particular column in a row is called,process on value request is called here i call a customized F4 based on the structure mapped to the row,but unfortunaletly unlike the screen the mapped structure i