Line out device not showing up

For some reason, I have lost my Line Out device. I now only have Headphone device. This does not work on most of my applications. Anyone know a fix for this...

This is the Mac OS X v10.6 Snow Leopard > Installation and Setup forum. Your post has nothing to do with the forum topic and more to do with your Mac's hardware so perhaps posting over in that forum may help you expose your issue to folks with the same configuration.

Similar Messages

HT6337 Allow handoff between this mac and your iCloud devices not showing up in general preferences

Is anyone not seeing this? the Allow handoff between this mac and your iCloud devices not showing up in general preferences
Imac 2011 21" mid 2011

nevermind, Just figured out that my iMac does not support it. Thanks Apple, once again coming up with stupid functionality that only works when you pay more money. 3yr old machine, I guess I need to send it to scrap heap.

Device NOT showing up on my monitor when plugged in?

Iphone plugged in.
Device not showing up? Any ideas?

You're welcome.
This link applies to a Mac.
http://support.apple.com/kb/ts1591

Devices not showing up on I-pod, how to disconnect safely?

devices not showing up on I tunes for I pod, how to disconnect I pod safely

I fixed the problem on my own , hey I'm a genius!! I clicked on my i-pod tab on the left column in i tunes and where the options for podcast tab is just changed the sync option to all podcasts instead of last looked at. Now i have all my podcasts in the video podcast menu on my i pod.

Device not showing in iTunes for 'Wi-Fi Sync' and 'Sync Now' on phone only works(appears dark) when plugged in via USB so kinda defeats object. Any ideas please?

Device not showing in iTunes for 'Wi-Fi Sync' and 'Sync Now' on phone only works(appears dark) when plugged in via USB so kinda defeats object. Any ideas please?

Had the same issue. Tried everything that was posted for troubleshooting bye apple and on the discussions.
Finally, tried something that solved it and it works flawlessly now. I changed my wireless router.
I was using my ISP's supplied ZyXEL PN660 ADLS2+ with Wireless N. Swtiched to an older Linksys WRT160N and it is working beautifully now.
Take a look at your router, make sure the firmware is up to date, and that UPnP is enabled, and if all is correct, and you have done everything else, try another Wireless router if you can.

Firewire device not showing

Greetings
using a G5, tiger 10.4.9
I have been using this computer for many months with no problem using firewire devices. I recently set up a seperate user account on the computer for my daughter. Prior to this ( for many months)I had a fireiwre device - LACIE external HD -connected that would mount each time at startup and show up on the desktop. Now, I can't get the icon on the desktop of the LACIE to show when I startup. I connected a camera to the computer using firewire, but it too would not show ( before it would). When I connected the camera using USB, it showed up on the desktop. Looks like firewire devices not showing. I checkd System Profile and it shows the LACIE device as connected and functioning. But it won't show up on the desktop. Any ideas on why I can't ge the Firewire devices to show on the desktop?
Thank you in advance for you help. . . .
Brian
G5 Dual 2.7 Mac OS X (10.4)
G5 Dual 2.7 Mac OS X (10.4)
G5 Dual 2.7 Mac OS X (10.4)
G5 Dual 2.7 Mac OS X (10.4)

Sounds like you have the name wrong. Open Disk Utility and take a look to verify the volume name. Disk Utility will list the drive itself, then indented below that is the volume name. To verify that you are using the correct name, try launching Terminal and do a list command:
ls -a /Volumes/"Name of Volume"
Hit the return key and see if the contents of the volume are listed. There is a space after "ls" and another after "-a"--if you don't get anything or get an error then you might want to try
ls -a /Volumes
and try copying the name from the list and pasting into the AppleScript.
Francine
Francine
Schwieder

Why does new music downloaded on one device not show up in the library of the other device?, Why does new music downloaded on one device not show up in the library of the other device?

Why does new music purchased on one device not show up in the library of the other?

Hi Bev5638,
Welcome to the Support Communities!
The article below will explain how to set up Automatic Downloads for your computer and devices.
iTunes Store: How to enable Automatic Downloads
http://support.apple.com/kb/ht4539
Cheers,
- Judy

Lion 10.7.2 / iTunes 10.5 - Devices not showing up

Any device attached via USB is not showing up in iTunes. I have the following ipad2, iphone 3gs and itouch (latest gen)
USB connections are working as ipad2 and itouch devices show up in iPhoto.
I have a Mac Pro Early 2008 version.
I've tried the following:
1) switching USB ports on my Mac Pro
2) rebooting Mac Pro leaving devices powered on
3) rebooting devices leaving Mac Pro on
4) turning everything off, and booting Mac Pro first. waiting 2minutes and then powering on ipad2, iphone, itouch
Nothing seems to work. Hoping someone else is stuck in the same spot or can advise next steps.
Thanks,
Nick

So far the only solution I have been able to find has been launching the recovery partition and running disk repair. That will fix the problem until you trigger it again. Fortunately, or unfortunately, I have pinpointed what triggers it on my computer.
Seems to be a flaw in keychain access. When Safari's connection times out due to an expired certificate (common in university networks that require a log in every few hours), the security settings freak out and effectively shut down safari's ability to do anything. The fact that it attacks KeyChain access and iPhoto and more is just a really big system wide glitch. Here's the run down:
http://digit.algravitas.com/2011/10/major-networking-glitch-found-in-os-x-v10-7- 2/

Successfully enrolled devices not showing in profile manager

On a newly installed (from scratch, formatted etc) Mountain Lion server, I'm having an issue where I can successfully enrol a device, an iPhone with 6.1 iOS in this case, but the enrolled device does not show up in the devices?
I see a previous post in these communities with a similar issue, the solution was to add place holders after the device was enrolled, unfortunately this is not a solution for me, as soon as you re-enrol the placeholder dissapears I have another server running mountain lion at another site and this is working just fine.
Any solutions? I'm pulling my hair out with this. I have a niggling feeling that with the other server I had a similar problem when I upgraded to Mountain Lion and had to edit one of the ruby files in the profilemanager to display the devices but I can't remember where or when
Regards,
Stephen...

ok update to this problem:
If I enroll a Mac device, in this case the mini server itself then these are displayed under the device library.
also tried an iPad with iOS6 and this was successful, and displays in the device library.
Currently the iPhone is not displaying although enrolled successfully is an iPhone4 so I'm going to experiment with a few other devices and see whats happening

TAPI Device not showing in application

I've installed the CiscoTSP.exe onto a Windows XP machine and the "CiscoTSP001.tsp" provider is shown in the Windows "Phone and Modem" screen, however, when I run any TAPI application that lists all of the available TAPI line devices, there is no Cisco line device listed (have tried 3 3rd party apps and the windows dialer.exe).
Is there anything else that has to be setup and do you need a valid connection to the CM to get the line device listed?

First of all make sure you are installing the CiscoTSP version for corresponding CCM version.
If you already installed TSP then uninstall it and remove the directory from programe files. Also remove the Cisco Wave driver from Device Manager in Control Panel.
Note that if you install the SimClient software provided by Cisco on the same PC where CiscoTSP is installed. Then TSP will not show devices.
Now restart the PC and install the TSP agian. Hopefully it will work. Try run Phone1.exe application which is widly used among TAPI developers.

Devices not showing in Max

I just tried to install a USB-6251 in my Laptop (Toshiba Tecra S2). The units is detected and the driver installs. It shows up in the device manager as a properly installed device. However, MAX does not show the device. The Laptop has WInXP-Pro, 2GB RAM and LV 8.20.
When I tried the same thing on my desktop, the 6251 installed in the same way, and then the option to run Test Panels showed up and the
unit ran happily.
Incidentally, I have a minor problem with a PCMCIA 6024 which takes a long time to show up under DAQmx in Max, and a PCMCIA -16E4 which insists on showing up under DAQmx as a 6024 (16E4 is not supported by DAQmx). Both show up promptly and work fine under traditional DAQ.
I suspect there is some problem in the device registration part of the WinXP - NI interface. These boards do not list under the add-remove hardware icon either.
Thanks in advance
Sanjay Gupta
Chief Scientific Officer & Ex-Head
Advanced Centre for Materials Science
Indian Institute of Technology
Kanpur 208016
Phones: +91-512-2597830, 3927830(Off), 2574628 (Res), 9336117477 (Mob)
Fax: +91-512-2597459
E-mail: [email protected], [email protected], http://home.iitk.ac.in/~sg

David,
Things have gone from bad to worse. I tried the upgrade in the Laptop with no success, and now the desktop is also playing up.
I have a ner full installation of the Academic Site License- PDS, RT, RIO ... (the works) on both my systems, as I am a regular user of cRIO for almost 1-1/2 years:
The Laptop story now:
1. After upgrading to 8.50 (no problems in the install), MAX still not ssing anything.
2. I tried to close the Configuration Manager it did not even do that. One process (I think mxssvr) did not close.
3. Tried removing MAX. Removed a lot of other things, incl. LabVIEW.
4. Removed the entire NI Install. Removed all NI directories in Program Files, Documents and settings > ... etc. Also, the FPGA directories in c:\ etc.
5. Using Regedit cleaned up virtually all National Instruments entries in the Registry. In otehr words removed all traces of NI software I could.
6. Reinstalled LabVIEW .....
7. Reactivated everything.
8. MAX (4.1) still not working
9. Checked in Admin Tools > Services. Found Configuration Manager and nidevldu not active.
10. Tried to start them. Config Manager does not start (Error 1067: The process terminated unexpectedly). nidevldu does start if started manually.
The Desktop:
1. Everything was fine.
2. Upgraded to DAQmx 8.50 incl MAX 4.2.
3. Now MAX does not work.
4. Admin > Services shows both processes running.
5. Still to try to shut down and manually try and clean up Data.
6. I was looking at some examination solutions and was able to run code (LV legacy) in LV. Could not try out DAQmx as could not do the easy reset from MAX.
I may add that the Laptop has had LV 7.1 (also possibly 7.0), 8.0 (incl. beta), and 8.2! The desktop did not have the 8.0's.
Any ideas! What do I do now. I always have the option of reformatting drive C and starting from scratch, but am loathe to do so. Will take a full working day at least.
Thanks
Sanjay.
Chief Scientific Officer & Ex-Head
Advanced Centre for Materials Science
Indian Institute of Technology
Kanpur 208016
Phones: +91-512-2597830, 3927830(Off), 2574628 (Res), 9336117477 (Mob)
Fax: +91-512-2597459
E-mail: [email protected], [email protected], http://home.iitk.ac.in/~sg

Line items are not showing in fbl1n/fk10n

hello all,
Again i needs your help. this time i am not able to see the line items in fbl1n and fk10n. system shows 360 line items are displayed but no line item are showing in screen.In fk10n i am just able to see the period wise balance. but line item not showing. this issue is only with my 5 vendor. in case of other vendor, i am able to see as i wish.
please suggest me how to solve it.
regards
konishko

Hi,
check the Reconciliation of that vendor.for that recon account line display should be selected.
For other vendors, reconciliation account is with line item display .selected. That might be the reason to show line items for remaining items.
check GL master of Recon acccount.

Network devices not showing up under "shared" in finder bar

Ok so i have a network that consists of a maxtor nas device, 2 win xp pc's, 1 win7 pc, d-link 524 router, and my macbook pro. I would like to be able to transfer files between my mac and the devices and use the printer attached to my maxtor. My issue is that none of the computers show up under the "shared" section of finder or under network. I use to have this issue with leopard but it resolved itself. Now under snow leopard for a couple months and i have yet to get it work. I can access my mac and other pcs from a pc. Anyone know how to get my network to show up on my mac?

Your problem is very common under Snow. At first my shares did not show up under shared in finder windows. I, then, of course, used "Connect to Server" to connect to the shares--both Mac and PC. I found that the more I kept the shares active the more likely they were show up under shared. Then, I discovered that if I kept the computers from sleeping during the period of needed access they would tend to stay in shared without nearly so much keeping the connections active.
If you do not like the above work around, then there are two other possibilities. You can elect to show mounted items on your desktop. Do that and connect to each share. Then, go > users > unlock > + login options > try dragging the mounted shares to the login item window. If successful, then the shares should be available at login.
Another approach is to mount and connect as indicated above. Then, making an alias to the share should at least make things faster.

CJI5 commitment line item report not showing po gross value

Dear All,
system is showing only net value in CJI5 report, actaully gross value of po must be reflected in CJI5 report and this happening in all po's like material, service's etc. example is as follows.
Example:
po net value: 1000
st 10%: 100
po gross value : 1100 (inclusive of all taxes, ed, disc. etc)
what could be the reason for not showing po gross value in commitment line item report.
Thanks & Regards,
Sandeep

Hi,
As far as i know the commitment report will never show you the value that is inclusive of taxes. It will only show the net value of the PO.
I just tried a scenario in my system by creating a PO for a net value of 3000 GBP and based on the tax code i entered system calculated a tax of 525 GBP. However when i check CJI5 report it shows only 3000 GBP as commitment and not 3525 GBP. This is how the standard system behaves, i believe. You can cross check this in the table COOI. The COOI table also shows the net value of the PO and does not include the tax amount in commitment.
Regards,
Gokul

Tax Line items are not showing seperately as per exp in FB60

Hi,
In FB60, I have booked the two expenses with tax code separately. While simulating the entry the tax lines are not showing separately as per expenses. For example:
Suppose my tax code = AB which is equal to 10% maintained in FTXP.
At present entry is coming as follows through FB60 is:
Debit     Postage expenses     500 tax code AB
Debit     Stationery expenses     400 tax code AB
Debit     Tax               100
Credit     Vendor               1000
But we need the entry is follows
Debit     Postage expenses     500 tax code AB
Debit     Stationery expenses     400 tax code AB
Debit     Tax               50
Debit      Tax               40
Credit     Vendor               1000
But I change the tax code for second line AB to XY then calculation of tax entries shows separately according to expenses.
Please let me know where did I do the mistake in configu2026u2026..
Regards,
Babjee

Hi!
Normally, all amounts being posted to the same GL Account and determined from the same tax code as automatically derived, will generate one common auto-generated line item. This is because tax reporting is usually based on tax code (external/tax reporting) and or GL account (internal/financial reporting).
In your first case since the tax code used for both line is the tax code was the same, it would be posting to the same GL Account - hence a common line item got auto-generated.
Check the Account Key and Assigned GL Accounts in T.Code FTXP. Additionally, check the Condition Type set-up (identified from FTXP) in T.Code SPRO / from menu IMG node Check Calculation Procedure.
Regards,
Ruchi

Line out device not showing up

Similar Messages

Maybe you are looking for