Line rate is higher than attainable rate!

I've been on Infinity for 3 or 4 months now and have had consistently a BT profile of 72.3 to 72.86Mbps, the changes occuring after modem resets or power cycles. Attainable rate (via the standard modem hack) has been 75272 to 76184kbps. Line rate has been 500 to 900 kbps below the attainable rate.
A few days ago we had a major power cut in the local area including here, lasting for several hours and afterwards, everything worked as normal. Just now I decided to check my BT profile and modem stats, just out of interest, as you do. The results are interesting - my profile has gone up to 75.73/20.00 and the modem stats are what I thought was impossible - line rate is much higher than the attainable rate! Stats are below.
Line is stable and needless to say I am delighted - I am now getting speedtest d/l results 3Mbps higher than ever before (74Mbps), but can anyone explain how line rate can be above attainable rate?
Mode    VDSL2
Traffic type    PTM
DSL synchronization status    Up
DSL up time    272927
   Line Status
    Downstream    Upstream
Attainable rate (kbit/s)   75948   26179
SNR margin (dB)        5.4      15.1
Line attenuation (dB)      0          0
Output power (dBmV)         13      3.8
   Statistics
      Downstream    Upstream
Line rate (kbit/s)   78235    20000
CRC errors      0             0
FEC errors               981       178
HEC errors             2182    0

You must have a good line and probably have the cabinet in your front room!
Who knows! I wouldn't say it would be impossible to hit pass your attainable rate, i would only take these as estimates as much as everything else.
It was like when i was on copper, thinking my line could only sync at 4MB, but constantly synced at around 6.5-7MB which was good for me! lol!
If you want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side If the the reply answers your question then please mark as ’Mark as Accepted Solution

Similar Messages

Increase in attainable rates and sync speed

I've noticed that my line is now syncing at 79999 down and 20000up, lasst week, and for the past 6 months the attainable rate has been 60000 down and 15000 up,
I'm still only getting 71000 down via the bt speedtest and 9000up, getting slightly better results on bbc though.
Also noticed my latency to the bbc is down from 25ms to 21ms
have there been any changes to the network or is this the DLM deciding that my line is good enough to handle higher speeds?

I don't think your line will improve even more, as you are at the limit of your package.
If you look at your modem stats you will see both sync rate and max attainable rate. The max attainable rate will only change significantly if something changes in your line. The sync rate will change as DLM thinks fit. If you see your max attainable rate is over around 90000, then maybe you could get more stable sync rate if BT offered a higher level Infinity package.
DLM will always keep your sync rate below the max attainable for stability. For reference, my values are a good but not perfect:
Max: Upstream rate = 23773 Kbps, Downstream rate = 81184 Kbps
Path: 0, Upstream rate = 20000 Kbps, Downstream rate = 73999 Kbps
Down Up SNR (dB): 7.9 14.5
Over the month or so I have been monitoring, my max attainable has dropped slightly, from just over 85000 to values around 82000. My sync speeds have gone up a lot to reach their current appropriate value, because I had had a previous wiring issue that had lowered my DLM.

Has anyone had any luck compressing videos with resolutions higher than 1080?

Everytime I try, it fails instantly. Is this not allowed in Compressor 4? It was possible in Compressor 3.

I have a 4K video that I'd like to compress using H.264 or X.264 and restrict the data rate.
Here are some details of the video (created in Motion) I am trying to compress:
DIMENSIONS: 4096 x 2048
FORMAT: H.264
FPS: 24
DATA SIZE: 53.2 MB
DATA RATE: 52.03 MB
and here are settings that I would like to compress it with using Compressor 4.0.4:
CODEC: H.264 or X.264 (both fail)
FRAME RATE: current
KEY FRAMES: Automatic
DATA RATE: Restricted to 7000 kbits/sec (setting it to automatic or any other data rate also fails)
QUALITY: Best
HEIGHT AND WIDTH: 100% of source
I have been able to get a successful compression with this 4K video file using ProRes 422, so that leads me to think this is a codec problem, not a Compressor application problem. Furthermore, I have had the same problem just using Quicktime 7 to export a video with these settings, I get the same failed results.
In Compressor it gives me the message Failed: Quicktime Error: -108
and in Quicktime 7 it gives me the message Failed: qKitErrorCatchAll (-6662)
So, if you had any suggestions about a better codec to use, one that allows me to restrict the data rate on higher than 1080 video files, it would be much appreciated.
Thanks
Evan

WSUS throwing 13002, "Client computers are installing updates with a higher than 25 percent failure rate. This is not normal."

Hello,
Within the past two months our WSUS Server started throwing error 13002, "Client computers are installing updates with a higher than 25 percent failure rate. This is not normal." We currently have 252 computers with errors in WSUS,
and 33 updates with errors. We have never had issues up until two months ago. If you keep rebooting the machine, and keep running updates, they eventually all install. I believe I will see the machines with errors go away as the weekly scheduled
WSUS install runs over and over, and the machines reboot.
- We run IE8 in our environment and sometimes IE9.
- We have 300 clients, all running Windows 7 SP1 x64.
- Our WSUS server is running on Server 2008 R2. The WSUS build number is 3.2.7600.262.
- We created an alternate WSUS 4.0 server on Server 2012, and redownloaded all updates. We put one client on it and it is showing errors on 3 updates, KB890830, KB931125, and KB2917500.
- Clients are throwing errors 800F0902, 80242016, and 80070005.
- I've noticed something with the C:\Windows\SoftwareDistribution\Download folder on the clients. When an update runs and fails, there is a "Install" folder created inside this folder. If you try to open it after the failure you get
"Access Denied" If you reboot the machine, the install folder goes away. (I assume this is a temp folder created to run updates). I've checked the permissions on this folder on various machines and all seems normal. I think
this is the root of the problem, and why we need to keep rebooting to get all of the updates to run.
- I tried deleting the Software Distribution folder on a client after stopping the update service, then restarting the update service. The folder redownloads but the client still throws errors.
- I've gone through our Group Policies looking for anything that can cause this and found nothing. We've created a test OU blocking inheritance, and only applying a WSUS policy in it to make it get the updates internally. I then rebuilt multiple
machines using Dell KACE, and still had failures.
- We run SEP 11 and 12 on our clients. I've tried removing the AV, making sure the firewall was off, etc. It still throws errors.
- I've spoken with our network team, and installed wireshark on a few clients looking for network errors and found nothing.
- I've tried various Dell KACE scripted installs on test machines (erasing and rebuilding the machines from scratch), after which I run Windows Updates from WSUS. They have thrown errors.
- I've rebuilt a machine using Dell KACE, undomained it, then ran updates externally from WSUS going to Microsoft's site, and I'm still getting errors.
- I've tried removing all software from the Dell KACE build to where it is just installing the OS and I'm still getting errors.
- I tried taking a plain Windows 7 x64 DVD and installing that on a test machine, then without domaining it and without installing any other software, running updates from Microsofts update site. This seems to work, althrough it does throw some errors
but I believe those are related to having to reboot your machine in order to complete the updates (I can't remember that error code at the moment).
Has anyone else been experiencing this? Any suggestions as to how I can fix this?

Hi,
Error 800f0902
Please try the method in this thread:
Error
Code: 800f0902
Error 80242016
If you receive Windows Update error 80242016 while checking for updates, it might be caused by a connection interruption between your computer and the Windows Update servers.
80070005
Usually means access denied
Since it worked perfectly for a while, did you make any change on the server? Any applications new installed on clients?

Is it possible to raise the bit rate of songs higher than 256 on iTunes? If not what should i use or do to raise the bit rate of songs?

Is it possible to raise the bit rate of songs higher than 256 on iTunes? If not what should i use or do to raise the bit rate of songs?

Songs you rip from CD can have their bitrate increased to a maximum of 320Kbps from the iTunes preferences; alternatively, the default encoder can be changed to a lossless one. Songs from other sources have a fixed maximum bitrate.
(67928)

Exporting sound for dvd studio 4. Studio 4 is only accepting ac3, saying bit rate too high in ALL other formats. However, aa3 auto levels the sound, which is not wanted, and it also drops the volume by about 40%, also not wanted. How do I get around this.

I have successfully used various formats and bit rates of sound in DVD Pro 4 with no problems, AIFF, WAVE, (obviously preferable as they give a good quality of sound as intended). However, of late, DVD Pro 4 refuses AIFF, WAVE, and anything higher than the lowest ac3 bit rate/format. This is rendering an aweful sound, auto volume leveled - which gives a very unprofessional fluctuation in volume and making a ionsense of careful sound editing. It also renders the volume at about 30% - 40% lower than the original master requiring huge increase in amplifier volume settings to get a decent volume.I have tried every format and bit rate, but FCP and DVD Pro 4 will only accept the lowest ac3 setting.
I have customers awaiting video of their concerts, can not deliver with this sound issue.
very much appreciate some assistance here.
Phil TP

I suggest posting this in the Final Cut Studio forum where regular users of DVDSP are more likely to see your post and respond. When you do, I would expect someone will ask why you arent using Compressor in your workflow…)
Good luck.
Russ

Boosting Bit Rate for Higher Quality

In Two Pass VBR Best DVD (bit rate defaults to 6.2mbps), if I pump up the bit rate to 9mpbs or higher, will my DVD quality increase? File size is not an issue -- it's a 15-20 minute video.
David A.

In theory, yes.
However - +and this is key+ - increasing the bit rate past a certain point will reduce compatibility with many set-top players. For the most part, so long as you're using Dolby Digital audio, you can make due with increasing the average to, say, 6.5 mbps. I personally would not advise going higher than 6.5 mbps unless you're only using the DVD for playback on systems you know you can control (your home or you mac).
Also, there is a certain point of diminishing returns with encoding. The 90 preset (6.2 & 7.7) is already at the high end of things.

VDSL2 (887VA) Low upstream Attainable Rate

Hi,
Recently swapped out my standard ISP router with a 887VA however the upstream sync speed is rubbish compared to the standard one. Any ideas on what to try? The router is running Version 15.2(4)M7
Old router:
Connection Speed: 37543kbps 6669kbps
Line Attenuation: 22.4dB 0.0dB
Noise Margain: 6.4dB 6.6dB
Cisco:
odem Status:       TC Sync (Showtime!)
DSL Config Mode:   AUTO
Trained Mode:       G.993.2 (VDSL2) Profile 17a
TC Mode:       PTM
Selftest Result:   0x00
DELT configuration:   disabled
DELT state:       not running
Trellis:     ON              ON
SRA:            disabled           disabled
SRA count:        0           0
Bit swap:        enabled           enabled
Bit swap count:   5628           0
Line Attenuation:      0.0 dB          0.0 dB
Signal Attenuation:      0.0 dB          0.0 dB
Noise Margin:          6.1 dB          6.2 dB
Attainable Rate:   44480 kbits/s       921 kbits/s
Actual Power:       12.1 dBm       10.5 dBm
Per Band Status:    D1    D2    D3    U0    U1    U2    U3
Line Attenuation(dB): 16.9   45.8   70.1   19.6   N/A   N/A   N/A
Signal Attenuation(dB): 16.9   45.8   70.1   19.6   N/A   N/A   N/A
Noise Margin(dB): 6.1   6.1   6.1   6.2   N/A   N/A   N/A
Total FECC:       466074           18816
Total ES:       6           0
Total SES:       5           0
Total LOSS:       5           0
Total UAS:       590           590
Total LPRS:       0           0
Total LOFS:       5           0
Total LOLS:       0           0
Full inits:       6
Failed full inits:   0
Short inits:       0
Failed short inits:   0
Firmware   Source       File Name (version)
VDSL       default    flash:vdsl.bin (10)
Modem FW Version:   110802_1752-4.02L.03.A2pv6C035d.d23j
Modem PHY Version:   A2pv6C035d.d23j
Vendor Version:
           DS Channel1      DS Channel0   US Channel1      US Channel0
Speed (kbps):      0   36031   0   763
SRA Previous Speed: 0   36046   0   759
Previous Speed:      0   36046   0   759
Reed-Solomon EC: 0      402474   0   17071
CRC Errors:      0      1706   0   0
Header Errors:      0   0   0   0
Interleave (ms): 0.00   16.00      0.00      8.00
Actual INP:   0.00      8.00      0.00      4.00

Also from a Draytek VDSL router:
VDSL
Link Status Showtime
Firmware Version 1414c3
Basic Status Upstream Downstream Unit
VDSL Profile 17a
Actual Data Rate 7897 34984 Kb/s
SNR 59 68 0.1dB
Attainable Rate 9370 35367 Kbps
Electrical Length 173 173 0.1 dB

ORA-25307: Enqueue rate too high, flow control enabled

I am stuck. I have my stream setup and they were previously working on two of my dev environments well. Now when I get the streams setup the CAPTURE process has a state of "CAPTURING CHANGES" for like 10 seconds and then changes to state "PAUSED FOR FLOW CONTROL". I believe this is happening because the PROPAGATION process is showing an error of "ORA-25307: Enqueue rate too high, flow control enabled".
I don't know what to tweak to get rid of this error message. The two environments are dev databases and there is minimal activity on them so i don't think it's a case of the APPLY process is lagging behind the PROPAGATION process. Has anyone run into this issue?? I've verified my db link works, my stream admin user has dba access. Any help or advise would be greatly appreciated.
thanks, dave

As rule of thumb, you don't need to set GLOBAL_NAME=TRUE as long as your are 100% GLOBAL_NAME compliant.
So, setting GLOBAL_NAME=TRUE will not have any effect if your dblink is not global_name compliant
and if your installation is global_name compliant, you don't need to set GLOBAL_NAME=TRUE.
The first thing when you diagnose is to get the exact facts.
Please run this queries both on source and target so that to see what are in the queues and where.
Run it multiple time to see if figures evolves.
- If they are fixed, then your Streams is stuck in its last stage. As a cheap and good starting point, just stop/start the capture, propagation and target apply process. Check also the alert.log on both site. when you have a propagation problem, they do contains information's. If you have re-bounced everything and no improvement then the real diagnose work must start here but then we know that the message is wrong and the problems is elsewhere.
- if they are not fixed then your apply really lag behind for what ever good reason, but this is usually easy to find.
set termout off
col version new_value version noprint
col queue_table format A26 head 'Queue Table'
col queue_name format A32 head 'Queue Name'
select substr(version,1,instr(version,'.',1)-1) version from v$instance;
col mysql new_value mysql noprint
col primary_instance format 9999 head 'Prim|inst'
col secondary_instance format 9999 head 'Sec|inst'
col owner_instance format 99 head 'Own|inst'
COLUMN MEM_MSG HEADING 'Messages|in Memory' FORMAT 99999999
COLUMN SPILL_MSGS HEADING 'Messages|Spilled' FORMAT 99999999
COLUMN NUM_MSGS HEADING 'Total Messages|in Buffered Queue' FORMAT 99999999
set linesize 150
select case
when &version=9 then ' distinct a.QID, a.owner||''.''||a.name nam, a.queue_table,
              decode(a.queue_type,''NORMAL_QUEUE'',''NORMAL'', ''EXCEPTION_QUEUE'',''EXCEPTION'',a.queue_type) qt,
              trim(a.enqueue_enabled) enq, trim(a.dequeue_enabled) deq, x.bufqm_nmsg msg, b.recipients
              from dba_queues a , sys.v_$bufqm x, dba_queue_tables b
        where
               a.qid = x.bufqm_qid (+) and a.owner not like ''SYS%''
           and a.queue_table = b.queue_table (+)
           and a.name not like ''%_E'' '
   when &version=10 then ' a.owner||''.''|| a.name nam, a.queue_table,
              decode(a.queue_type,''NORMAL_QUEUE'',''NORMAL'', ''EXCEPTION_QUEUE'',''EXCEPTION'',a.queue_type) qt,
              trim(a.enqueue_enabled) enq, trim(a.dequeue_enabled) deq, (NUM_MSGS - SPILL_MSGS) MEM_MSG, spill_msgs, x.num_msgs msg,
              x.INST_ID owner_instance
              from dba_queues a , sys.gv_$buffered_queues x
        where
               a.qid = x.queue_id (+) and a.owner not in ( ''SYS'',''SYSTEM'',''WMSYS'') order by a.owner ,qt desc'
   end mysql
from dual
set termout on
select &mysql
/B. Polarski

Another Data Rate Too High Error Question

Hi all,
I have seen quite a few posts about pgc errors, but most of them deal with slideshows and not video; and I can't find anything with the REF=KApgc error.
I'm just putting all of my home movies onto an authored DVD, not rocket science. I'm using the 'Film Submenu' preset with only 5 main movies, things like Easter, Birthday, etc. My transition for each button is a slate (for lack of a better word) that says exactly what it is and when it happened, before each movie plays.
After I had everything set up, I realized I didn't have an ability to "play all" that would include these slates. Simple solution, make a 'play all' button that links to a timeline that has everything in it - the slate, then the movie, next slate, next movie and so on. (When I say movie - they are all .mov files rendered out from After Effects, even the slates)
My transcode settings are NTSC DV High Quality 7mb VBR 2 Pass and the "maximum quality" box is checked.
When I run the 'Check Disc' all is fine. Preview the disc, all is fine.
Build Disc: Hours of Transcoding then the error: Data Rate Too High at *timecode* REF=KApgc.
When this movie is by itself with a button click, it's fine. It's only in the "play all" timeline that it produces the error.
If the data rate isn't too high in one place, why is it too high in another? It's the same thing, just a longer timeline.
Please Help!
Thanks.

Thanks Jeff,
I feel kind of silly for not thinking of that as a solution to my play all dilemma. That's why you're the expert I guess.
A better solution would be to create a playlist of all of your other timelines; that way, only one copy of each gets burned to disc.
Hopefully the "data rate" error will go away with these changes.
-Jeff
Can I place my slates that are just assets (.mov) in the playlist or can I only put timelines in there?
Thanks again,
-Jim

Can a single tax code (v5) have more than one rate of intrest?

can a single tax code (v5) have more than one rate of intrest?..
v5 can it have both 4 % and 5 % ??
(v5 comes under a condition type jipc..it is used for cst in a PO)

in that case ,(two rates)
if i use
function module, CALCULATE_TAX_FROM_NET_AMOUNT
how will get correct tax amount?
coz i will just mention
bukrs,
tacode,
amount,
currency
in the FUNCTION MODULE..
also can u help me find VAT CST amounts RATES for a invoice?
if i use the above FM i get the follwoing error
'tacode v5 not found in procedure TAXINN'
functional guy says configuraion is right..
pls help..
i need to make purchase register...

Stumped - Video Bit Rate too High Error

I just upgraded to FCP 7x and I am trying to burn a disc on DV Studio Pro. It runs through the rendering fine, then when it is ready to burn it shuts down and says the video bit rate to high. So I went to the manual and the manual suggested changing the codec to Apple Pro 422, something like that. I did and am now still getting the same error. This has never happened before and I've been using FCP for 6 years. Anybody know what to do or has had a similar problem?

mvp productions wrote:
It runs through the rendering fine
Let's get some terminology correct. I believe you mean it "compresses" fine. How are you compressing the file. In Compressor?
the manual suggested changing the codec to Apple Pro 422
I think you may have misread that. All SD DVD's are made from m2v files for picture and ac3 or aif files for audio. Pro Res is an editing codec.
This is my quick and easy how to make a first play SD DVD.
Just send the sequence to Compressor (Right click the sequence and send or export to Compressor). From Compressor choose the settings for DVD Best Quality 90 minutes (If your project length is longer choose a longer time). Submit the files. This will create 2 files. An m2v for picture and ac3 for audio.
Bring both of those files into DVDSP. Add the files to the empty track (a green box). Right click the track and select first play. Build the DVD then Burn.

PCM problem - Muxer Bit Rate Too High

I'm continually receiving the error "Muxer error Bit Rate Too High." I've narrowed it down to the PCM audio that I'm using. I know many would recommend that I switch to .AC3. Unfortunately, that is not an option.
I received audio from 3 sources. From an audio post house, the quicktimes produced on my mac and the encoded PCM files from the Maestro real time mpeg encoder. The weird thing is that the PCM files from the real time encoder work fine. If I remove all the audio, but leave the PCM from Maestro...there are no issues.
I have even gone as far as outputting from FCP to dbeta and then re-encoding with Maestro and that didn't work.
Any help would be greatly appreciated.

Erik, you may be about to hate me, but I am just making sure I understand the process of elimination, you deleted all audio from all tracks and ONLY left the PCM audio on the main track and it did not build? And the same thing for each of the menus (all audio out of the project except for a menu at a time?)
1.) Not sure how you made the menus or you default preferences within DVD SP, but if the encoding rate for menus was high and it was a motion menu the spike could still happen.
2.) If the steps were as above, take a look at the build file on your computer to see where it is crashing out and/or watch the log to see what is being muxed when the projects crashes
3.) If in fact that leaving just the PCM audio in the track by itself (not the 5.1) you may want to delete preferences and the MPEG/PAR files that DVD SP creates and also repair permissions. Then take the PCM and try rexporting from Quicktime to AIF and use a different name for the file such as "SecondTry.aif" so it is clear it is the other file.
BTW which version of DVD SP are you running and which version of QT?

MUXER Bit rate too high

I am in the process of creating a PAL version of an existing NTSC DVD
I created PAL-compliant video files from iMovie.
Then, I took the existing NTSC DVDSP project, and:
- deleted the existing video files from the clips and the Assets
- Set the video standard to PAL
- Saved the DVDSP project under a new name
- Imported the PAL video files as assets and attached them to the clips.
I left the audio files as is (all AC3)
I kept the same menus (Menu1 has a PAL video as a background)
When I try to build, I get an Muxer Bit Rate too High error message right after the Auto play segment is processed (see log below)
The Autoplay segment is a slideshow made up of jpeg pictures with a "cube" transition. There are two audio streams and two subtitles streams (one in English, the other in French).
I never had that problem when burning the NTSC version. What do I need to change?
Here is the log of the build:
Building Project Tibétains bilingue PAL
01/03/07 08:45:52
Build Folder /Volumes/MAXTOR HD/PAL videos
Starting DVD Build 5TIBTAINS_BIL...
Compiler Initializing...
Precompiling Project 5TIBTAINS_BIL
Parsing Assets...
Encoding Assets...
Compiling VMG Information...
Created 13 PGCs in VTSM1
Created 13 PGCs in VTSM1
Created 5 PGCs in VTSM2
Created 5 PGCs in VTSM2
Created 5 PGCs in VTSM3
Created 5 PGCs in VTSM3
Created 9 PGCs in VMG.
4 Menu(s) will be created...
Compiling Menu PGCs...
Compiling Menu#1 (Menu 1)...
Rendering Menu:Menu 1,Language:1...
Rendering Menu:Menu 1,Language:2...
Compiling Menu#2 (Menu 2)...
Rendering Menu:Menu 2,Language:1...
Rendering Menu:Menu 2,Language:2...
Compiling Menu#3 (Menu 2a)...
Rendering Menu:Menu 2a,Language:1...
Rendering Menu:Menu 2a,Language:2...
Compiling Menu#4 (Menu 1a)...
Rendering Menu:Menu 1a,Language:1...
Rendering Menu:Menu 1a,Language:2...
Writing VIDEO_TS.VOB
Compiling Menu PGCs...
Writing VTS020.VOB
Compiling Menu PGCs...
Writing VTS030.VOB
3 VTSs and 9 Titles will be created...
Compiling VTS#1 (5 Tibetains21)...
Preparing Subtitles...
Muxing VTS011.VOB
Done.
Compiling VTS#2 (auto Play)...
Writing VTS020.VOB
Generating Transition: auto Play, Clip 1...
Generating Transition: auto Play, Clip 2...
Generating Transition: auto Play, Clip 3...
Generating Transition: auto Play, Clip 4...
Generating Transition: auto Play, Clip 5...
Generating Transition: auto Play, Clip 6...
Generating Transition: auto Play, Clip 7...
Generating Transition: auto Play, Clip 8...
Preparing Subtitles...
Muxing VTS021.VOB
Muxer Bitrate Too High
Thanks,
Pierre
Dual 1.25 G4 Mac OS X (10.3.9) DVDSP 3.3

While waiting for an answer, I tried a few things.
I solved the problem by re-doing the slideshow for the Autoplay segment.
I believe that the issue was the fact that I had converted the slideshow into a track in the NTSC version.
That track had to be removed and re-created in the PAL version (just like any other video asset).
Hoping that this will help someone else.
Pierre

Why do I get data rate too high error after capture and save? (using AJA Kona)

I record(capture) about an 70 min program with Adobe premiere CS5 once a week. About a year ago I got the error *data rate too high" when stopping "capture" when saving program to Video HD(2TB). The video recorded was OK but after about 15 min the audio was out of sync and garbled. I thought I had found the problem by defragging the video drive. I have not had any problems for about 50 weeks.. until this week-it happened again. I know the video drive(2TB) was defragged and only half full. I was able to recover the program since I back up the program on a DVD but had to go through a lot of problems massaging it since I send the program to a local ABC broadcast station in 16/9 SD and the DVD is rescored in 4/3 .
I have the CS5 program on a separate 2.5 GB drive. I am running Win7pro and have a RAID series of Intel Xeon ES410 processors.
Any help as to why I get this "Data Rate too High" when saving program would be appreciated.
Thanks much!

I have three Mitsubishi broadcast quality cameras (two HD -waiting on money for switcher and 3rd HDcamera). They feed to their camera control untints and then to a switcher and then into video computer and the C5S. I probably am not answering your question. I can access the computers from my home(I also have a CG computer). Is there some way I can tell you from the C5S program which the info you need? I have it ready to record for next week.
I know how to manipulate various functions but I do not know all the ins and outs of the Premiere settings-an IT man set those up for me two years and he is no longer available.
Thanks

Line rate is higher than attainable rate!

Similar Messages

Maybe you are looking for