Line reset after faults in area

Hi,
A fault in our area caused my line to drop dozens of times yesterday. Now I am stuck at 12 db SNR and a slow connexion and low IP profile. Now the faults in the area have been fixed can I get a mod here to carry out a reset on my line to get me back to my normal 6db SNR / 8000 / 7000 IP profile ?
thanks guys
Solved!
Go to Solution.

xDSL
xDSL
Mode
ADSL_G.dmt
Traffic Type
ATM
Status
Up
Link Power State
L0
Downstream
Upstream
Line Coding (Trellis)
On
On
SNR Margin (dB)
12.6
24.0
Attenuation (dB)
37.0
22.0
Output Power (dBm)
19.9
12.1
Attainable Rate (Kbps)
6436
1188
Rate (Kbps)
6080
448
K (number of bytes in DMT frame)
191
15
R (number of check bytes in RS code word)
8
16
S (RS code word size in DMT frame)
1.00
1.00
D (interleaver depth)
64
8
Delay (msec)
16.00
16.00
INP (DMT symbol)
1.29
0.26
Super Frames
405330
405330
Super Frame Errors
2
0
RS Words
27562440
3445679
RS Correctable Errors
542
2
RS Uncorrectable Errors
5
0
HEC Errors
4
0
OCD Errors
0
0
LCD Errors
0
0
Total Cells
98808740
0
Data Cells
1111069
0
Bit Errors
204
0
Total ES
1
0
Total SES
0
0
Total UAS
0
0

Similar Messages

Line reconnected after fault can I get my IP Profi...

Have had a fault/disconnect on my line for the past week and a half preceeded by a lot of disconnects which forced down the IP profile. Openreach engineer reconnected the line this morning and I was hoping the IP profile would be reset but it is at 0.35, can this be overidden?
On the Kilkhampton exchange 20CN.
Thanks.

welcome to the BT community forum where customers help customers and only BT employees are the forum mods
in order for the forum members to help please can you post the adsl stats from your router you may need to 'show detail' to get all stats (if hub enter 192.168.1.254 in your browser and navigate to adsl or if HH4/5 then go to troubleshooting then logs and you are looking for 2 line together when hub last connected to internet and they will show your connection speed and noise margin or if netgear enter 192.168.0.1). Then run btspeedtester (MAC users may have problems). when first test completes then run diagnostic test and post the results ( do not reset the router).
your profile should automatically correct itself given 3/5 days stable connection - maybe even sooner
Someone may then be able to offer help/assistance/suggestions to your problem
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

HT4859 How do I retrieve my photos from the cloud after a reset. My photos are gone from my phone, and I backed them up on iCloud?

How do I retrieve my photos from the cloud after a reset. My photos are gone from my phone, and I backed them up on iCloud? when I restored it, no camera roll pictures?

Try restoring the backup again. Sometimes it's successful the second time. You could also try restoring an older backup. iCloud will have your last 3 backups is you have sufficient storage space in your account.

Things are so hard to find in the new pages! Like where is the place where I can adjust the line spacing AFTER a paragraph? Grrr.

Things are so hard to find in the new pages. Does anyone know where to find the "adjust line spacing after paragraph" control?

Oh I just solved my own question! Drop down pops when you click the arrow attached to spacing.Just in case anyone else has the same question.

10 days training period after line reset

Hi,
So on Monday morning the engineer finally turned up and did line reset which in results I was getting my full speed (47.5/9). And very low pings 16ms to bbc.co.uk, abou 6ms on 1st hop but this morning hh5b decided to restart in results my ping went up by 12ms, now 28ms to bbc.co.uk and it decreased my speed by 3mb. Can anyone explain me how 10 days of training period works? I thought the router must stay stable for more than 10 days. Is it still training my line after router drop?
I suspect interleaving turned on on my line but why after only 2 days instead of 10 training days?
I have been told by engineer that I am very far away from the cabinet around 800m and that the line is working in 100% just after line reset and it wont stay like that.
Best regards

Tonight I have noticed that I can't open any website (it takes about 3 minutes to open any website) and I am having a high packet loss on teamspeak3. The Noise Margin dropped from stable 6.0 to 4.5-5.0. It forces me to reboot my router but I don't want to, because my speed will drop and ping will go up occasionally. What can I do in that situation?
Some stats:

Request a Line reset?

I upgraded to Infinity about 6 months ago. The line speed never increased from what we'd had originally - we went from 5mb ADSL to ... 5mb Infinity.
I meant to complain and try and get it sorted but you all know that process and I just didn't have the time or the patience.
Anyway, so... two days ago we had a phone fault. Engineer comes out, finds the issue out in the woods and fixes it, no problem. However when he's testing our line before he goes, he sees our old data cable (from the wall to the router) and says it's not good enough. He says it's probably giving router issues and throttling our bandwidth.
I bought a new twisted pair data cable and whoomph, we jumped to 6mb just like that, and the ping has doubled in speed - browsing is lightning fast now.
But we are still WAY off what the Availability Checker said we'd achieve, and way off what the engineer said he *thinks* we should be getting based on his tests... He said MAXIMUM possible would be about 25mb, which in his experience suggested we should be looking at 15 - 18mb. He also said we may need a line reset before we see any real speed improvement (after replacing the cable).
6mb is great an all, and I'm not one to look a gift-horse in the mouth, but when I upgraded I was promised 12-18mb, and we're still way off that.
So, all that said and done... Should I ask for a Line Reset from BT, or will the speed likely increase automatically over the next few days?
Solved!
Go to Solution.

your connection will recover but it could take a few weeks.
resetting you connection at present can only be done following an engineer visit so surprised engineer did not organise that before he left
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

System should not allow to delete PO line Item after GR/IR

Hi,
I am working on a SAP Retail Implementation project.
Currently the system is allowing us to delete the PO line items after doing GR or IR against that PO line item. But the clients requirement is that the system should not allow to delete PO line item after doing GR/IR.
We are using Account Assignment Category-N, Item Category-S.
Please let me know if you have the solution for this requirement.
Thanks in advance
Thanks & Regards,
Suresh

Hi,
Standard SAP will not allowed the PO to be deleted once it was GR done. The controlled is on the attributes of message to set as "E"
Message no. 06115
But if invoiced takes place, the is the point that PO can be deleted.
You have to do have a Enhancement using MM06E005, insert you logic here to check PO history tables like EKBE, then check if invoice " Q" (BEWTP) exist, the PO cannot be deleted once the user delete the PO line and SAVE it. Ask you developer to help you on the following coding.
Use MM06E005 and EXIT_SAPMM06E_012
IF SY-TCODE = 'ME22N'.
IF sy-ucomm = 'MESAVE' OR SY-UCOMM = 'YES'..
LOOP AT TEKPO.
IF TEKPO-LOEKZ = 'L'.
SELECT SINGLE BELNR FROM EKBE INTO BELNR1 WHERE EBELN = TEKPO-EBELN AND EBELP = TEKPO-EBELP AND BEWTP = 'E'.
IF SY-SUBRC = 0.
SELECT SINGLE BELNR FROM EKBE INTO BELNR2 WHERE EBELN = TEKPO-EBELN AND EBELP = TEKPO-EBELP AND BEWTP = 'Q'.
IF SY-SUBRC = 0.
Regards,

A very good friend of mine dropped her iphone into water and now it is not working.Her husband recently passed away and text messages from him and from well wishers after his decease are feared lost. Is there any way to retrieve them?

A very good friend of mine dropped her iphone into water and now it is not working.Her husband recently passed away and text messages from him and from well wishers after his decease are feared lost. Is there any way to retrieve them?
I suggested contacting Compub in Nassau St as the info is priceless and worth the trouble of trying to regain?
Any thoughts? The poor lady is very distress

If she has backed up her iPhone she can replace that iPhone and set up the new iPhone from her backup.
You can put the iPhone that went into water into a plastic baggie with either new silica gel packets (preferred) or raw rice and let it sit for 4 - 5 days. After that time remove the phone and connect it to power for at least a half hour. While it is still connected to power reset it by holding down the power and hold button, wait for the Apple logo then let go of the buttons. Might take several tries. If it revives immediately back it up.

Creating and Selecting a line in After Effects CC?

OK, So I suppose this is a two part question...
But there is a little thing in After Effects CC that is annopying me alot, and it could just be me, and the way I've been doing things...
1) The way I have creating a simple Line in After effects, is by using the pen tool, placing two points, and then just using a stroke on the Shape Layer, and no fill. Is this the most efficient way to creating a line in After Effects? It's what i have always done, and it's not until CC that it has been a pain.
2) The reason why it's inconveniencing me is when i try to select that Shape Layer in the Comp Viewer! For some reason, in CS6, when i wanted to select that line, i could just click on it, and it selects the layer, Now, when i click on the line i just made, nothing happens, no where in the line that i can click or highlight will it select the layer of that line, Instead, I have to click the very center of the composition for some reason. there is small unseen point there that i either have to click exactly, or click and drag in that area, in order to select the layer, which gets annoying if there are many line at any given moment. This point is also where the anchor point for the layer is placed.... Is there any way to change this? To be able to change some setting so that when i click on the line itself, it selects it, and to have the Anchor point be placed in the center of the two point i make?

But I do this kind of thing all the time. The last 5 projects involved 8 stroked horizontal and vertical shape layers drawn with the path tool that I had to move around the screen. I also had a bunch of little shapes that were only 5 X 5 pixels. These layers are nearly impossible to grab in the comp window at even 200% zoom factor without inadvertently grabbing the wrong layer or scaling the layer when you try to move it in the comp window.
It is like trying to drive a screw with a hammer. It will kind of work but you will do a much better job if you use a screwdriver and the screw will remain undamaged. Hence, selecting small assets in the timeline and moving them around with the transform properties from the timeline is using a screwdriver. Using the direct selection tool is just the wrong tool for this and it always has been. You have to have some real estate to grab on to if you expect to move a layer without scaling it.
You can mitigate the scaling problem for small layers by adding a simple expression to scale so the layer always stays at 100% but this will just automatically fix the scale problem and won't help moving the layer around in the comp window very much.

BB Line Reset Question

Hi - had issues with BB speed - ip profile was set to only 0.25mbps. BT did a line reset on Monday lunchtime. IP profile is still set ot 0.25mbps. Contacted BT who said it would take 10 days for the line to stabilise and spped will vary in that time.
Surely the IP Porfile should have been increased as part of the reset or will it automatically increase during the stabilisation period ? Normal speeds are 2-3mbps.
Thanks

ok got them
ADSL line status
Connection Information
Line state
Connected
Connection time
0 days, 00:03:12
Downstream
4,608 Kbps
Upstream
448 Kbps
ADSL Settings
VPI/VCI
0/38
Type
PPPoA
Modulation
G.992.1 Annex A
Latency type
Fast
Noise margin (Down/Up)
6.2 dB / 21.0 dB
Line attenuation (Down/Up)
47.0 dB / 29.0 dB
Output power (Down/Up)
7.0 dBm / 1.6 dBm
Loss of Framing (Local/Remote)
0 / 0
Loss of Signal (Local/Remote)
0 / 0
Loss of Power (Local/Remote)
0 / 0
FEC Errors (Down/Up)
0 / 0
CRC Errors (Down/Up)
0 / 0
HEC Errors (Down/Up)
0 / 0
Error Seconds (Local/Remote)
0 / 0
Hide Details

Thin lines appear after flattening PDFs

Hello,
Whether we export a layout using one of the PDF/X standards or tell Acrobat Pro to flatten afterwards, the file appears to have thin white lines bordering all the previously semi-transparent areas. Upon zooming in as close as possible, these lines appear to be very negligibly thin and thus not likely to appear in print. However, this of course makes the PDF unusable except for printing (it looks bad at normal zoom with all these random boxes).
Is this normal behavior or should we be choosing another PDF preset or PDF exporting method? Has anyone had any problems with commercial printers showing these artifact lines?
thanks,
JP

The flattener creates what is referred to as "atomic regions" as part of the flattening process...basically it divides the content up, creating or maintaing vector objects and rasters as needed. After flattening, these "artifact" lines are sometimes visible at those atomic region boundaries if, in Preferences under Page Display > Rendering > Smooth Line Art is turned on. This setting has a tendency to exaggerate those lines, which is what you are seeing. When printed they should not be visible.
Can the files be saved as PDF/X4 which supports live transparency? Keeping the transparency live should also mean a smaller file size than a flattened file.

Mouse tracking always reset to a specific area point

Hi,
My iMac mouse always reset to a specific area of my screen every time I move it.
I thought that it was the magic mouse tracking that was bugging but it's not : the same problem occurs when I'm using the ScreenSharing app with my computer on sharing mode.
I tried to restart the computer, empty the PRAM after unplugging the computer but nothing worked..
Here's the specs of my iMac :
iMac 27-inch, Late 2012
3,4 GHz Intel Core i7
32 Gb of ram
NVIDIA GeForce GTX 680MX 2048 Mb
OS X Yosemite 10.10.1
Someone could help me please?

Everything is ok finally : I haven't seen that the pen of my graphic tablet was layed down on it..! -_-

How can we substitute the invalid option "reset after read" in FP-CTR-500 + FP-1600 frequency measurement application?

We nned to incorpore the values of 2 frequency signals (0-10 Khz)into a process controlled by a VisualBasic application running on 1 PC with W'95. Because the FP-CTR-500 working with FP-1600 hasn't the option "reset after read", the process of reading is a bit complicate, and sometimes, we receive wrong values of frequency from those devices. Could you help me? Is there any extremely reliable method of reading? Best regards,
Puho

For frequency measurement information on the FP-CTR-500/502 modules. Please see KnowledgeBase Article #1TB63SUS
http://digital.ni.com/public.nsf/3efedde4322fef19862567740067f3cc/d8db42f9fdc3607e862568640047f144?OpenDocument
Ultimately, the FP-CTR-500/502 modules are not designed for frequency measurement, although it is possible to use them to measure frequency. The one thing is that it works best to do the measurements over relatively long integration periods (1/4 second or more).
Regards,
Aaron

Line resets and stuck profiles (question not issue...

One of the mods in their calls to me mentioned that they are happy to do some line resets for me but want to avoid them too often since this caused the DLM to get concerned over the line status. [I have no reason to doubt this statement]
Now in my case what I sometimes could do with is getting a IP profile unstuck ie when it passed the point where it should have changed but has not and yes the BT system says that it did.
Is this the same thing as a line reset (which one would think it shoudl not really be) and if not can anyone confirm that this does not anger the DLM?
[the reason for asking is that normally my profile should go up within 24 hours at most which is bearable but recently it has stuck twice, ie BT says 1000 but speedtester and throughput showed 750].
If my post was helpful then please click on the Ratings star on the left-hand side If the the reply answers your question fully then please select ’Mark as Accepted Solution’

To clarify, first the image is placed, then there is a rectangle over the image whose frame is slightly larger than the image frame, with transparent fill, and set the stroke to thick white with transparency lowered to induce the "reflection" sort of effect. Take a look at this screenshot: http://screencast.com/t/AYQDwx3g7w
Hope this helps.
Cheers
Parikshit

CC 2014 trial. MPEG MOVIE clips flickering on my time line! after render, and after export. tried all kinds of sequence settings,taking out transitions and effects ,even the audio tracks.....still flickering. They play fine outa the project files!? HELLL

CC 2014 trial. MPEG MOVIE clips flickering on my time line! after render, and after export. tried all kinds of sequence settings,taking out transitions and effects ,even the audio tracks.....still flickering. They play fine outa the project files!? HELLLLLPPPPP!!!!

We can not see your computer, your settings or even know what your source files are because we are not in the same room as you are!
We cant see what you are doing wrong ...so you will have to tell us a lot more and show us some screen grabs of your settings.

Line reset after faults in area

Similar Messages

Maybe you are looking for