Line through display

My iMac has recently begun to slow down frequently, where I get the spinning beach ball and can't do a thing for periods at a time. This is intermittent, but it is more and more frequent.
Something I've noticed that has begun to occur around this same time is that occasionally, I'll have a white line going through the middle of the display. If there are windows open (like a browser window), it usually goes through that. If I'm in a browser and I hit refresh, it goes away. However, I can take a screen shot and capture the image.
Does this suggest a motherboard issue or graphics card failure? Or is it something else, perhaps?
Thanks for your suggestions,
Kevin

This afternoon, I ran the Apple Hardware Test that came with the restore disk and it passed. I also booted off the Snow Leopard disk and ran Disk Utility, checking the hard drive. It passed that.
My wife had a MacBook Pro with a similar problem, though the horizontal lines she was getting were thin black. The one on mine is wife and slightly wider. It extends through the browser (usually the top most app) and across the desktop. Turns out my wife had the logic board replaced and that fixed the issue, which is why I was worrying about that option.

Similar Messages

There are horizontal white lines through display picture, and some vertical blue lines. sometimes screen is all black, sometimes whited out, sometimes half white lines, half completely unvisible. white lines have spread from just a few on top

i just want to know if anyone has encountered this problem and if it is worth getting fixed/looked at. its an older nano so im thinking about just buying an itouch. any help is greatly appreciated!!

Hi, and welcome to Apple Discussions.
Problems like this can be caused by a cable pinched in the hinge. When you start seeing the display problems, does adjusting the angle of the display make a difference?
There is a known logic board fault in this model iBook which resulted in the iBook Logic Board Repair Extension Program. However, in my experience, if the logic board is involved with display anomalies, it causes the system to freeze up, necessitating a hard shutdown and waiting several hours for a restart. Another symptom of the logic board problem is if pressure on the case to the left of the trackpad on the left wrist rest improves the situation.
Based on my experience, it sounds more like a cable caught in the hinge, since you're not seeing system freezes. Let us know if adjusting the display's angle (a bit forward or a bit back) makes a difference.

My MacBook Pro has no sound every time it try to turn it up it displays a round cirlce with a line through it.

My MacBook Pro has no sound every time it try to turn it up it displays a round cirlce with a line through it.

Hi DeathDrone,
Welcome to the HP Community! I will be happy to help with your sound problems. However, I will need some additional information to better assist you. What is your operating system? What is your product number?
Find your product number on a notebook:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c00033108
Finding your OS:
http://windows.microsoft.com/en-CA/windows/which-operating-system
Thank you,
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

I upgraded the OS on my iMac to Lion from the App store; and after installation, it restarted and now the operating system won't start up.... it keeps displaying the apple/folder with a question mark and a circle with a line through it! Please help!

I upgraded the OS on my iMac to Lion from the App store; and after installation, it restarted and now the operating system won't start up.... it keeps displaying the apple/folder with a question mark and a circle with a line through it! Please help!

Try starting up with your Snow Leopard DVD and see if the disk can be repaired. Once you are at the installer screen go to the Utilities Menu and choose Disk Utility and choose repair disk. You might also want to try Diskwarrior.
Hope this helps.
Ben

Vendor Line Item display/ and Purchase order Field

FI Experts
We recently implemented the MM PO module in SAP, we are creating PO's automatically in SAp from a 3 party system. We are using field "Our Field" EKKO-UNSEZ to enter a reference from the 3rd party system. Our account payable have requested that they need this field to display in FBL1N "Vendor Line Item Display". I tried by using special fields but table is not available. Anyone has any suggestions? I know I can use BSEG and EKKO but it is too big of a table to use. Does this requires more of an ABAP report rather than just a simple QUERY report?
Your suggestions are appreciated.

Hi,
PO Nr. doesn't appear in Vendor line item, but yes, in GRIR account.
So when are you performing MIRO, you may use XREF3 field, which usually remains blank, through user exit (OBBH) for populating PO Nr. But yes, if you are processing MIRO of multiple POs, you may not be able to set multiple values.
BR

8800, battery symbol with red line through it. Won't boot. Please help!!!

I recently bought a 8800 and when I inserted a battery, all I got was a battery symbol with a red line through it on a dim screen. I changed batteries, tried to charge it via USB and from a wall outlet to no avail. I tried cleaning the contacts and tried uploading t a new OS, but it wont recognize the phone being connected when it actually is.    I am at the end of my rope with this phone and can't figure out what else to do. Is it just gone? Please help me
Solved!
Go to Solution.

Leave the device to charge 2-3 hours, and then, still connected to the USB cable, remove the the battery from the device a few seconds and reinsert it. If it boots--leave it to charge to 100% (check Options > Status for the percentage).
If it doesn't boot--try using a wall outlet charger if you are not. If you are connected via USB to the PC, make certain that you have Desktop Manager (or the USB device drivers) installed, which you can download below.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

No line item display in FAGLL03 & FBL3N GL line Item reports

Dear All,
I have parked the customer invoices with normal customer recon account and with special GL indicators. The system do not display parked lines for Special GL indicators. How can i display the line item display information in FAGLL03 and in FBL3n report.
Following settings have already been made are;
1. Fs00 = line item display check is on.
2. In initial screen for FAGLL03 & FBL3N Selection: Parked Items Parked items are displayed and checked.
The only information for parked special gl line items is get through FBL5N report only.
Kindly suggest in there any way that we can get report from GL line Item reports???
Regards

Some how client do not want the functionality

Difference in GL Balance display and GL line item display

Dear All,
Can any one help me why the difference between GL display and GL line items display?
Thanks in advance
regards
Elan

Hi,
You can do the following:
1. carryout gl balance carryforward from previous to current year : Use t.code:F.16
You can cross check the fs10n balance with FBL3N balance from previous years. Assume these balance are matching for previous year 2007 and 2008, you have this problem only in 2009, then you can carryforward this balance from 2008 to 2009 once again. Some times users may post some adjustment entries as per the auditors recommendations. If this balance is not matching from 2007 itself, then first carryforward the balances to 2008 then 2009. You can run this transaction no of times.
2. check the master data of gl account through t.code:FS04, whether any changes has been done to line item display field?
If you find any changes to line item display field then run the program "RFSEPA01" to get all the line items.
3.If your issue was not resolved even after the above two activities, then let me know the sap version you r working.
all the best
Prasad

General Ledger - Open Item Mgt/Line Item Display

Hello Experts,
GL Account was created with no tick in open item mgt and line item display. Business users posted few entries and now realised that the accunt type should be open item manageable and display should be at line item level. Going through the SDN forums, few experts suggested the workaround as follows:
1. Block for posting GL master
2. Make it zero balance in the account(clear existing trans)
3. Run program(SE38) RFSEPA01
4. Check Open Item Check box/Line Item Display
5. Unblock the GL master
6. Continue posting as normal.
However the above solution was recommended for 4.7 or earlier versions and for ECC 6, the recommendation was to open a totally new GL master with correct attributes and block the old GL master.
My client is running ECC 6.2 but requires this corrected asap and I wonder if anyone can suggest a better solution than creating a totally new GL master.
Appreciate quick resolution/advice.
Thanks
Mohammed.

Hi,
Please refer to Sapnote_0001356457_activate OIM, and it mentions in complete details how to handle OIM activation when documents are posted to it.
Regards,
SAPFICO

Profit center clearing accounts line item display

Dear all,
I have implemented document splitting at profit center level.
The zero balance clearing account (profit center clearing account) is open item managed and also line item display tick is put. eg both ticks are active.
I am trying to see the line items in the account using fbl3n,fs10n etc but am not able to view the line items althought the balance of the account is visible in fs10n.
the message i get is 'no line item selected'.
Pl suggest some way through which i can see the line items of the profit center clearing account.
Regards,
Rishikesh

Dear Venkatesh
I am also facing same problem, I am using T Code FAGLL03 to display Line Items for Zero Balance Clearing A/c but I am not getting line item display instead it is giving following error.
=========================================================================
Account 141010, company code VALC is clearing account
Message no. MSITEM111
Diagnosis
You have stored account 141010 in company code VALC as a clearing account. At the same time, you use line item management with this account.
System Response
Error message issued because line item display cannot read data for an account in a ledger if line items exist partially in the entry view together with clearing items for which there are no line items. In such cases, only the data with line items would be selected.
Procedure
Check the Customizing settings or account control. Change the settings so that only automatic postings without line items can be made to the account, or select a different account as the clearing account.
=========================================================================
Please do suggest me.
Thanks in Advance
Regards
Ratnakar

Reg fbl5n customer line item display

I n FBL5n report wbs element field value is not displaying
When posting the invoice through FB70
wbs element field name PROJK
I have searched in SDN but any thread not related to this one
Suggest me how to display the value
Regards
Suri
Edited by: mannem suresh9 on Dec 23, 2011 7:06 PM

Hi
If you don't have available this field, you can enhance FBL5N list. Please, see the article [Offsetting Account Description in FBL3N & FAGLL03 u2013 GL Line Item Display Reports|http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/8011026d-eb5d-2e10-b9bb-d0601949b86a?QuickLink=index&overridelayout=true] by Imran Mohammad Khan. K in this site.
I hope this helps you
Regards
Eduardo
PD: See also [Addition of Fields in Line Item Display Report Output for TCode FBL1N/FBL5N|http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/40d6c489-aa3a-2e10-db88-deb9114b6854?QuickLink=index&overridelayout=true] by Swapnoneel Mukherjee.
Edited by: E_Hinojosa on Dec 27, 2011 9:37 AM

Problem with cents:"G/L Account Bal. Display (FS10N) vs. Line Item Display

Dear colleagues,
We have used BSIS table within a batch input program using standard transactions such as F-02 and OASV, in order to leave several "old" G/L accounts completely up to zero, and therefore transferring their complete amount to "new" G/L accounts.
What we see in several "old" accounts after doing the transfer is that system still displays me 1, 2 or 3 cents in transaction FS10N......but if I double click for its G/L account line item display, system correctly tells me that the old g/l account is completely balanced. Logically, for I have checked in BSIS table through program which is the necessary amount to balance the old g/l account.
So we can say there is a lack of coordination between what I see in the first screen of FS10N and the Line Item display screen of the g/l account. No doubt, old account is completely balanced and well transferred to new g/l account (checked in BSIS table), but FS10N still reports few cents.........isn´t it somehow mischievous?
Does anyone know how to clean those cents (which actually are virtual cents)? Is there any sap note reporting this bug and providing the solution?
Thank you so much for your kind attention on reading my post and best regards.
F. Albisu

Dear Neeraj,
Yes you are right, there a lots of notes related to this issue.
I have found note 595776 which I think best fit with my problem. Would you hindly read it and confirm to me, from your point of view, I am in the correct track?
(Of course, the system I am talking to you abput, proceeded to the Euro Conversion in 2002)
Thanks!

In FI Line Item Display Purchase Document Not appearing

Dear All,
Could you please help me, how i can get the Purchasing document Number in Line Item Report .
Thank you in advance.
KSK

Hi
You have to add Purchase Document (PO) as a special field in the line layout variant through customizing to view PO in the FBL3N Line layout,
Go to SPRO Settings - **** - GL Accounting - GL Accounts - Master Records - Line Items - Line Item Display - Define Special fields for finding and sorting data"
A message will be displayed that it is a cross client change. Presse nter
Before adding the special field PO, the line layout variant does not have the field PO
Click on New Entries button
Give the Table as BSEG and Field as EBELN.
And save.
Assign points if useful.
thanks
radhika

Multiple line item display for PAYMENT ADVISE form(script) using F110 tcode

Dear All,
I am currently working on PAYMENT ADVISE script ( form ) - for which i have copied the
form F110_IN_AVIS to zform.
I am executing the form for output through executing Tcode - F110.
The output works for single line item entry of vendor line items - but doesnot support
for muliple line items.
I have checked the standard program - RFFOUS_C - which has include - RFFORI06 for remittance advice -which supports for single line item display.
Kindly advise me for the soultion of the same.
Regards
HC

Hi,
Do you manage to fix it ?
we experienced the same problems (mass printing smarforms F110), we would like to use one time F110, and generates all the spool, for all the line items.
Thanks
Any help would be grateful.
Thomas

Adding Special Field in the line item display

Dears Through SPRO settings, I added the field 'Group Account Number' (ALTKT) for the GL line item display.
It is now transported to Quality.
When I try to see that field in the change line item layout, I could not find that field for inclusion.
However, in the SPRO of Quality, I find that field already appearing.
Why it is not appearing in the FBL3N special field screen ?

Hi Niki,
I am not sure how you have added this filed but if you follow these steps you will have it.
1- Run FBL3N and make your settings and execute it (F8).
2- Go menu Settings > Special fields (You can run it by t code OBVU out of FBL3n also)
3- Add a new entry, select your field (BSEG ALTKT Group account number) and save it
4- Back one step (F3) and select "Change layout..." icon.
Now you have the field in "Hideen fields" column. Just select it as "show selected fields"
Regards,
Omid

Line through display

Similar Messages

Maybe you are looking for