Link C3850 to Dell 8132F Using SFP Interconnect (copper)

I am introducing new Cisco C3850 switches into an existing Dell environment. This will be a phased replacement so I have a need to link the 3850's to Dell 8132F's. My 3850's each have a C3850-NM-4-10G network module and the Dell switches have SFP+ ports. So the plan is to link the switches using 10GB links. I would like to use the copper SFP+ interconnect cables. But the distance between the switches require a 10 meter cable (SFP-H10GB-ACU10M). But the 3850 specs only list the 5 meter (SFP-H10GB-CU5M) cable as supported.
So I have two questions. First is if the 10 meter cable will work and second has anyone run into any issues linking the 3850's to Dell switches via 10GB.

I think I answered my first question. Doing a bit more digging I found the "Cisco 10-Gigabit Ethernet Transceiver Modules Compatibility Matrix" which shows the SFP-H10GB-ACU10M is supported on the 3850 with OS XE 3.6.0E installed.
Still would like to know of anyone linking the 3850 to the 8132F however...

Similar Messages

New iMAC to Dell 3008 using Mini DisplayPort to Dual-Link DVI Adapter

I just brought the new iMAC 27" iCore7. Previously I was using old MBP with dual link DVI to DELL 3008 and they did fine.
But Today I connect the Dell 3008 to my new iMAC using Mini DisplayPort to Dual-Link DVI Adapter...They could not work properly...
The dell shows images in red with flickers....
I've contacted the phone for help...and they said nothing could be done????!!!!!
Anyone could help??
THX

just update my progress...
I had made calls to Apple technical support center in HONG KONG for help...
To my surprise...they even did not understand what I was saying(Or just pretending...)....One interesting guy said I could take the new iMAC back to service center to change the 4850 display card to older version...or call DELL for help!!!!!
Fuxking Apple technical support center in HONG KONG
I was almost hopeless until I found a minidisplay port to display port cable in Circuit Assembly:
http://estore.circuitassembly.com/products/Mini-Displayport-to-Displayport-Adapt er-Cable.html
ONLY $14.95 !!
They sent the cable to me in 3 days time...and I hooked it up right away when I received it today...my Dell 3008 could display 2560 x 1600 normally again!!!!!
The problem is: Apple is still selling its FUNCTIONLESS Mini DisplayPort to Dual-Link DVI Adapter at high costing....sounds like cheating others....
What' s wrong with the Apple nowadays???

Sfp interconnect between 2960 and 3560

Hi,
Can anyone tell me if the sfp interconnect cable can be used between 2960-48TC-L and a 3560-48PS-E?
Thanks
Andy

in short, YES.
the 3560-48PS-E has the 4 SFP ports.
the 2960-48TC-L has two 'dual purpose' uplinks which can support SFP or copper.
(you can only use one type at a time; not SFP and copper simultaneously)
please see the following links for more info on those two devices:
2960 -
http://www.cisco.com/en/US/products/ps6406/products_data_sheet0900aecd80322c0c.html
3560 -
http://www.cisco.com/en/US/products/hw/switches/ps5528/products_data_sheet09186a00801f3d7d.html

CISCO CATALYST 3560 SFP INTERCONNECT CABLE

What is the advantage of using this SFP cable over a 1000BaseT GBIC and daisy chaining the switches together?
Just curious???
Thanks!

The advantage comes down to cost. Whether you can realize this advantage depends on the distance between the two Catalyst 3560 switches.
If the distance is less than or equal to 50cm, then one SFP Interconnect Cable (CAB-SFP-50CM=) at US$250 is a much less expensive way to connect the two switches than two 1000BASE-T SFP (GLC-T=) at US$395 each = US$790 plus a Cat5 or better UTP Gigabit Ethernet crossover cable.
If the distance is greater than 50cm but less than or equal to 100m, then the 1000BASE-T SFPs are your least expensive option. The alternative is MM or SM fiber.
If you have to connect a Catalyst 3560 SFP interface to another Catalyst switch that takes GBICs, then the SFP Interconnect Cable is not even an option. From 0 to 100m, 1000BASE-T SFP and GBIC (WS-G5483=) would be your least expensive way to go.
If there's any chance you will be redeploying these switches somewhere else in the future, you may want to put the 1000BASE-T SFPs in now. That way you'll already have them when you need them later.

Help Needed - My BB 8520 Curve has this message-CRTranRec::GetLinkedRecordID:Invalid linked record id while sychronisation using the desktop software

Hi!
Need some help with the same:
Help Needed - My BB 8520 Curve has this message-CRTranRec::GetLinkedRecordID:Invalid linked record id while sychronisation using the desktop software

Hi sameer197301 and welcome to the BlackBerry Support Community Forums!
To clarify, are you seeing this message displayed on your BlackBerry® smartphone or on your computer?
Thanks.
-CptS
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

How do i go about linking 2 laptops 3 ipads using the same itunes and to stream all films and music

how do i go about linking 2 laptops, 3 ipads using the same itunes and to stream all films and music through the house.

make sure they are all using the same itunes store account and turn on home sharing
http://support.apple.com/kb/HT3819 - more info about home sharing
-mvimp

How do i link to a specific tab using the spry tabbed widget

Hello i'm working on a microsite using the spry tabbed widget. I'm having trouble figuring out how to link to a specific tab using a an external link.
here is the site. http://www.efaxcorporate.co.uk
for example: if i wanted to give a user a url link specifically tab#2.
Im sure this is really easy i just can't seem to figure it out.

Try http://foundationphp.com/tutorials/spry_url_utils.php

How to I set an internal link in a PDF document using Preview? After setting a link under the Tools/Annotations menu, the link doesn't work and no detailed instructions are provided.

How to I set an internal link in a PDF document using Preview? After setting a link under the Tools/Annotations menu, the link doesn't work and no detailed instructions are provided via the Help menu other than it showing the pull-down menu selection to make.

No. I am able to use the other features such as underlining, highlighting, adding rectangles and oval and save those changes.

If I get a user to enter their name as a variable and I am linking one movie to another using a button, is there a way to carry the user name forward into the second movie?

If I get a user to enter their name as a variable and I am linking one movie to another using a button, is there a way to carry the user name forward into the second movie?

Hi there
See if the link below helps
Click here
Cheers... Rick
Helpful and Handy Links
Captivate Wish Form/Bug Reporting Form
Adobe Certified Captivate Training
SorcerStone Blog
Captivate eBooks

How do I keep the source document open when linking to a target document using the destination option in Adobe X?

How do I keep the source document open when linking to a target document using the destination option in Adobe X? Have several links to create in the source document and want to keep the source document and target document open at the same time.

Go to Edit - Preferences - Documents and un-tick "Open cross-document links
in the same window".

Hello, I have includes a Web link in an image. When I convert the document in PDF, the link remains inactive. Could use me? Thank you.

Hello,
I have includes a Web link in an image.
When I convert the document in PDF, the link remains inactive. Could use me?
Thank you.

No version of Pages will allow images to be links. We always got around this by bracketting the image with text and making the link in that.
Pages 5 has lost the ability to have cross links in pdfs and seems to have a bug that disables any links after the first page.
Peter

Sending PDF forms (created using SFP) as Email Attachment

Hi,
     I have created bunch of ADOBE forms using SFP. They are not interactive forms. created using ADOBE Live cycle designer.
I have the Function module and by executing I can view the PDF form in print preview mode. But I have to save this in backend and attach to email.
I have a program that have to send one of the forms created in SFP as email attachment to outside SAP.
Please advice how to achieve this.
Thanks,
Sanjeev

Hi ,
Please find below a code sample for your requirement
*& Report ZENVOI_PDF_MAIL
REPORT zenvoi_pdf_mail MESSAGE-ID ad.
TYPE-POOLS : abap .
DATA : data_for_update TYPE zdemopdf ,
       hexa            TYPE solix_tab.
DATA : fm_name   TYPE funcname ,
       param     TYPE sfpoutputparams,
       doc_param TYPE sfpdocparams ,
       output    TYPE fpformoutput .
param-nodialog = abap_true. " suppress printer dialog popup
param-getpdf = abap_true.
doc_param-langu = sy-langu.
doc_param-country = 'FR'.
doc_param-fillable = abap_true.
doc_param-dynamic = abap_true.
CALL FUNCTION 'FP_FUNCTION_MODULE_NAME'
EXPORTING
    i_name     = 'ZDEMO_PDF'
IMPORTING
    e_funcname = fm_name.
CALL FUNCTION 'FP_JOB_OPEN'
CHANGING
    ie_outputparams = param
EXCEPTIONS
    cancel          = 1
    usage_error     = 2
    system_error    = 3
    internal_error = 4.
CHECK sy-subrc EQ 0.
CALL FUNCTION fm_name
EXPORTING
    /1bcdwb/docparams = doc_param
    data_for_update    = data_for_update
IMPORTING
    /1bcdwb/formoutput = output
EXCEPTIONS
    usage_error        = 1
    system_error       = 2
    internal_error     = 3.
CALL FUNCTION 'FP_JOB_CLOSE'
EXCEPTIONS
    usage_error    = 1
    system_error   = 2
    internal_error = 3
    OTHERS         = 4.
CALL FUNCTION 'SCMS_XSTRING_TO_BINARY'
EXPORTING
    buffer     = output-pdf "PDF file from function module
TABLES
    binary_tab = hexa.
* Envoi du mail
** CLASS-DEFINITIONS
DATA: send_request       TYPE REF TO cl_bcs.
DATA: document           TYPE REF TO cl_document_bcs.
*DATA: sender             TYPE REF TO cl_sapuser_bcs.
data: sender            TYPE REF TO if_sender_bcs.
DATA: recipient          TYPE REF TO if_recipient_bcs.
** INTERNAL TABLES
DATA: l_mailtext TYPE soli_tab.
DATA: iaddsmtp   TYPE TABLE OF bapiadsmtp.
DATA: ireturn    TYPE TABLE OF bapiret2.
** VARIABLES
DATA: mail_line LIKE LINE OF l_mailtext.
DATA: bapiadsmtp         TYPE bapiadsmtp.
DATA: subject    TYPE so_obj_des.
DATA : att_subject TYPE so_obj_des.
DATA : w_except TYPE REF TO cx_root .
CONSTANTS : c_defmail TYPE ad_smtpadr VALUE
                 '[email protected]' .
FIELD-SYMBOLS : <smtp> TYPE bapiadsmtp.
*Set subject of the mail
subject = 'Exemple de PDF interactif'.
* Set text of the mail
mail_line = 'Merci de remplir le formulaire et nous le retourner'.
APPEND mail_line TO l_mailtext .
att_subject = 'Template du PDF'.
TRY.
* Create persistent send request
    send_request = cl_bcs=>create_persistent( ).
* Get sender object
    sender = cl_sapuser_bcs=>create( sy-uname ).
*    sender =
*      cl_cam_address_bcs=>create_internet_address( '[email protected]' ) .
* Add sender
    CALL METHOD send_request->set_sender
      EXPORTING
        i_sender = sender.
* Read the E-Mail address for the user
*    CALL FUNCTION 'BAPI_USER_GET_DETAIL'
*      EXPORTING
*        username = sy-uname
*      TABLES
*        return   = ireturn
*        addsmtp = iaddsmtp.
*    LOOP AT iaddsmtp ASSIGNING <smtp> WHERE std_no = 'X'.
*      CLEAR bapiadsmtp.
*      MOVE <smtp> TO bapiadsmtp.
*    ENDLOOP.
*    CASE bapiadsmtp-e_mail.
*      WHEN space.
        recipient =
     cl_cam_address_bcs=>create_internet_address( c_defmail ).
*      WHEN OTHERS.
*        recipient =
*     cl_cam_address_bcs=>create_internet_address( bapiadsmtp-e_mail ).
*    ENDCASE.
* Add recipient with its respective attributes to send request
    CALL METHOD send_request->add_recipient
      EXPORTING
        i_recipient = recipient
        i_express    = 'X'
        i_copy       = space
        i_blind_copy = space
        i_no_forward = space.
* Set that you don't need a Return Status E-mail
    CALL METHOD send_request->set_status_attributes
      EXPORTING
        i_requested_status = 'E'
        i_status_mail      = 'E'.
* set send immediately flag
    send_request->set_send_immediately( 'X' ).
*Build Document
    document = cl_document_bcs=>create_document(
                        i_type    = 'RAW'
                        i_text    = l_mailtext
                        i_subject = subject ).
*     add attachment to document
    CALL METHOD document->add_attachment
      EXPORTING
        i_attachment_type    = 'PDF'
        i_attachment_subject = att_subject
        i_att_content_hex    = hexa.
* Add document to send request
    CALL METHOD send_request->set_document( document ).
* Send document
    CALL METHOD send_request->send( ).
    COMMIT WORK.
CATCH cx_send_req_bcs INTO w_except.
CATCH cx_address_bcs INTO w_except.
CATCH cx_document_bcs INTO w_except.
ENDTRY.
Hope this help you .
Best regards

When I use dynamic link how do I continue using it after closing and reopening a project?

Hi
Im very new to AF
I cant seem to find the answer to this in any tutorials.
When I using dynamic link, how do I continue using it after closing and reopening a perm pro project?
Thanks
Philip

Hi Kevin
Thank you very much for such a quick reply.
I actually figured it out. As usual it was fairly obvious solution.
I opened both project at the same time.
Thanks again and sorry for waisting your time.
R
Philip

Embedding linked PSD's in AI using AS/JS

Hi,
I am looking at a way of embedding linked PSD files into an AI doc using either Applescript or Javascript. The AI docs I work with already have the PSD's placed as linked images. I am using Illustrator CS2 (12.0.1) on a Mac, running OS 10.4.10.
I need to ensure that the PSD files are embedded with the "Convert Photoshop layers to options" option set, so that the blending options set on the PSD layers are honoured when brought into Illustrator. This works fine when done manually, as the "Photoshop Import Options" window appears for each PSD I embed.
I encounter a problem when trying to embed a PSD using AS/JS though. In both cases, there are no options available to be used in conjunction with the 'embed' command. 'Embed' seems to assume and use the "Flatten Photoshop layers to a single image" option, which does not honour the PSD layer blending settings.
i Things tried:
*tried setting the Photoshop options to preserve layers in AS prior to running 'embed' i.e.
>set photoshopOptions to {class:Photoshop options, preserve layers:true, pixel aspect ratio correction:false}
>set IllustratorPreferences to {class:Illustrator preferences, Photoshop file options:photoshopOptions}
I have tried the equivalent in JS too.
I can see that the preference is being set, but this still has no effect on the 'embed' command as these prefs relate to opening PSD files in AI only (same "Photoshop Import Options" window though?!)
*have looked at UI Scripting in AS - I am able to select and press the "Embed" button in the Control Palette in AI, but AI does not respond at all, i.e. I can see the "Embed" button change colour when clicked but nothing else. Other UI elements in AI respond correctly to being clicked, just not the buttons in the Control Palette.
So any help/guidance/suggestions etc would be greatly appreciated.

You need to expand and ungroup after the trace. Then delete the white you do not want. I missed a little piece in the last screen shot. But you get the idea. I put a black background behind the trace.
Traced:
Expanded and ungrouped:
White selected:
White deleted:

I have samsung corby gts3653 mobile and need to connect internet to mac through it but it doesn't have wifi and pcsuite for mac and how could i able to connect it through gprs? GPRS is active in mobile but unable to link it with macbook pro(using lion os)

i have samsung corby gts3653 mobile and need to connect internet to mac through it but it doesn't have wifi and pcsuite for mac and how could i able to connect it, through gprs? GPRS is active in mobile but unable to link it with macbook pro(using lion os) can any one reply.

Until the MacBook Air was released and supported in 10.5, the Mac did not consider USB to be a valid Networking Protocol. So set the Mac with USB solutions aside.
To connect computer-to-computer, you typically need to be using an Ethernet crossover cable. Assigning the same address to two Ethernet devices is never the solution -- it gives a Network Conflict, just as you said.
If your Windows box has some mechanism for Sharing its WiFi connection over Ethernet, you would have to follow its rules. Whether that means Manually assigning an Ethernet Address in the same range or the PC will provide the Address, I do not know.
Best success may be running an Ethernet cable to your Wired/Wireless Base Station, or using a "gaming adapter" (Ethernet-to-Wireless no drivers required) connected to the Mac's Ethernet port to give it WiFi access. What is your Base Station {Cable, DSL, FIOS, Other} ? Ethernet cables can be up to 100 meters (an American Football Field). Often the Base Station can be moved closer for more convenience.

Link C3850 to Dell 8132F Using SFP Interconnect (copper)

Similar Messages

Maybe you are looking for