Link down on control plane

Hi Everyone!
What will be if delete Control-plane from Cisco route?

I doubt its got anything to do with the control plane of the router. As the control plane is not a link of any sort. It is like brain of the router and helps perform routing related functions.
Can you check show log on the router around the time the issue occurred? Control plane may manage some interface states like PPP, LACP etc. Check the router logs, it may point you what exactly is happening and you can address the issue accordingly.
-Terry

Similar Messages

Link between phase and control plan

Hi there!
Someone knows if there is possibility to link a control plan with a phase?
And then approve a phase only if a related control plan is completed?
Thank
Bye
Luciano

Hi,
This is not possible in standard functionality till SAP cProject suite 4.0
Niranjan
Let me know if it helps !!!

6807-XL - Control plane interface showing down in logs and NMS

Getting the below logs on the switch and NMS station is also showing the CPP interface is down.
Jul 01 12:09:55: %LINEPROTO-5-UPDOWN: Line protocol on Interface Control Plane Interface, changed state to down
Any thoughts?

Getting the below logs on the switch and NMS station is also showing the CPP interface is down.
Jul 01 12:09:55: %LINEPROTO-5-UPDOWN: Line protocol on Interface Control Plane Interface, changed state to down
Any thoughts?

Do you know a unicast protocol for the Ethernet control plane?

Hi,
Does anyone know a protocol for the Ethernet control plane which has a unicast destination address?
MVRP, MMRP, MSTP, RSTP, all these protocols have a multicast reserved destination address.
Perhaps we have to look non-802.1Q control plane protocols.
Best regards,
Michel

Hi Peter,
> I wonder if any of the OAM protocols, especially the one providing the loopback/ping test is unicast-based.
In G.8013 (07/2011) section 7.3:
"The Ethernet loopback function (ETH-LB) is used to verify connectivity of a MEP with a MIP or
peer MEP(s). There are two ETH-LB types:
• Unicast ETH-LB.
• Multicast ETH-LB".
> In any case, think of LOOP frames sent by Catalyst switches to detect self-looped ports. In these frames,
> the source and destination MAC address are set to the unicast MAC of the egress port.
As I said above, it's a good case for my little study.
The LOOP frame, from Cisco, was certainly interesting and important before 2004.
Since 802.3ah-2004 we have the OAM remote loopback (in link OAM, and not network OAM as ETH-LB).
Best regards,
Michel

Ethernet/networking link down // AppleYukon2 - en0 link down

*Massive writing into a Volume located on a NAS // Ethernet/networking link down // AppleYukon2 - en0 link down*
Scenario
Writing a massive data into a volume (sparsebundle) on a NAS (network attached store).
*Problem / Error*
Always during this process the Ethernet link down.
Then the MAC OS X (10.5.6) freeze – no reset, no shutdown and no volume eject – after trying some clicks the spinning wheel comes and only soft reset or hard reset shutdown.
*Technical Info*
Wireless Device: Linksys - WRT54G firmware updated
NAS/External Hard Drive: Iomega - Home Network HD firmware updated
MacBook Pro // Mac OS X (10.5.6) // 2.2 GHz Intel Core 2 Duo // 2 GB
Logs
+LOG 1+
Apr 8 18:56:30 wslyMac /System/Library/CoreServices/backupd[207]: Backup requested by user
Apr 8 18:56:30 wslyMac /System/Library/CoreServices/backupd[207]: Starting standard backup
Apr 8 18:56:36 wslyMac /System/Library/CoreServices/backupd[207]: Mounted network destination using URL: smb://admin@STORAGE-7AB4/TimeMachine
Apr 8 18:56:36 wslyMac /System/Library/CoreServices/backupd[207]: Backup destination mounted at path: /Volumes/TimeMachine-1
Apr 8 18:56:58 wslyMac kernel[0]: AppleYukon2: 00000000,00000001 sk98osx sky2 - - sk98osx_sky2::replaceOrCopyPacket tried N times
Apr 8 18:57:07 wslyMac hdiejectd[231]: running
Apr 8 18:57:08 wslyMac kernel[0]: jnl: disk1s2: replay_journal: from: 8088064 to: 15072256 (joffset 0x7d0000)
Apr 8 18:57:25 wslyMac kernel[0]: jnl: disk1s2: journal replay done.
Apr 8 18:57:25 wslyMac fseventsd[37]: event logs in /Volumes/TimeMachine_Backup/.fseventsd out of sync with volume. destroying old logs. (1989 18 2969)
Apr 8 18:57:25 wslyMac /System/Library/CoreServices/backupd[207]: Disk image /Volumes/TimeMachine-1/wslyMac_001b63b30d6b.sparsebundle mounted at: /Volumes/TimeMachine_Backup
Apr 8 18:57:25 wslyMac /System/Library/CoreServices/backupd[207]: Backing up to: /Volumes/TimeMachine_Backup/Backups.backupdb
Apr 8 18:57:29 wslyMac fseventsd[37]: log dir: /Volumes/TimeMachine_Backup/.fseventsd getting new uuid: CBE196F1-1008-4BFB-8D4A-AD9504E68ACF
Apr 8 18:57:59 wslyMac /System/Library/CoreServices/backupd[207]: Event store UUIDs don't match for volume: Macintosh HD
Apr 8 18:58:00 wslyMac /System/Library/CoreServices/backupd[207]: No pre-backup thinning needed: 29.79 GB requested (including padding), 245.17 GB available
Apr 8 19:20:31 wslyMac kernel[0]: AppleYukon2: 00000000,00000017 sk98osx sky2 - - sk98osx_sky2::replaceOrCopyPacket tried N times
Apr 8 19:21:35 wslyMac kernel[0]: AppleYukon2: 00000000,0000001b sk98osx sky2 - - sk98osx_sky2::replaceOrCopyPacket tried N times
Apr 8 19:21:53 wslyMac kernel[0]: AppleYukon2: 00000000,0000001e sk98osx sky2 - - sk98osx_sky2::replaceOrCopyPacket tried N times
Apr 8 19:23:32 wslyMac kernel[0]: AppleYukon2: 00000000,00000004 sk98osx sky2 - - sk98osx_sky2::replaceOrCopyPacket tried N times
Apr 8 19:23:37 wslyMac kernel[0]: AppleYukon2: 00000000,00000001 sk98osx sky2 - - sk98osx_sky2::replaceOrCopyPacket tried N times
Apr 8 19:23:41 wslyMac kernel[0]: AppleYukon2: 00000000,00000011 sk98osx sky2 - - sk98osx_sky2::replaceOrCopyPacket tried N times
Apr 8 19:25:32 wslyMac kernel[0]: smbiodsendall: Timed out waiting on the response for 0x32
Apr 8 19:25:38 wslyMac kernel[0]: AppleYukon2: 00000000,000003e8 sk98osx sky2 - - sk98osx_sky2::replaceOrCopyPacket timedout
Apr 8 19:32:07 localhost kernel[0]: npvhash=4095
+LOG 2+
Apr 8 22:03:19 wslyMac /System/Library/CoreServices/backupd[356]: Backup requested by user
Apr 8 22:03:19 wslyMac /System/Library/CoreServices/backupd[356]: Starting standard backup
Apr 8 22:03:19 wslyMac /System/Library/CoreServices/backupd[356]: Mounted network destination using URL: smb://admin@STORAGE-7AB4/TimeMachine
Apr 8 22:03:19 wslyMac /System/Library/CoreServices/backupd[356]: Backup destination mounted at path: /Volumes/TimeMachine-1
Apr 8 22:03:26 wslyMac /System/Library/CoreServices/backupd[356]: Disk image /Volumes/TimeMachine-1/wslyMac_001b63b30d6b.sparsebundle mounted at: /Volumes/TimeMachine_Backup
Apr 8 22:03:26 wslyMac /System/Library/CoreServices/backupd[356]: Backing up to: /Volumes/TimeMachine_Backup/Backups.backupdb
Apr 8 22:03:26 wslyMac /System/Library/CoreServices/backupd[356]: Ownership is disabled on the backup destination volume. Enabling.
Apr 8 22:03:26 wslyMac KernelEventAgent[35]: tid 00000000 received unknown event (256)
Apr 8 22:03:27 wslyMac /System/Library/CoreServices/backupd[356]: Event store UUIDs don't match for volume: Macintosh HD
Apr 8 22:08:22 wslyMac /System/Library/CoreServices/backupd[356]: Backup content size: 66.6 GB excluded items size: 44.6 GB for volume Macintosh HD
Apr 8 22:08:22 wslyMac /System/Library/CoreServices/backupd[356]: No pre-backup thinning needed: 26.46 GB requested (including padding), 249.57 GB available
Apr 8 22:08:22 wslyMac /System/Library/CoreServices/backupd[356]: Waiting for index to be ready (909 > 0)
Apr 8 22:40:50 wslyMac kernel[0]: AppleYukon2: 00000000,0000009c sk98osx sky2 - - sk98osx_sky2::replaceOrCopyPacket tried N times
Apr 8 22:40:50 wslyMac kernel[0]: AppleYukon2: 00000000,00000008 sk98osx sky2 - - sk98osx_sky2::replaceOrCopyPacket tried N times
Apr 8 22:40:50 wslyMac kernel[0]: AppleYukon2: 00000000,00000004 sk98osx sky2 - - sk98osx_sky2::replaceOrCopyPacket tried N times
Apr 8 22:41:20 wslyMac kernel[0]: smbiodreconnect: Reconnected to STORAGE-7AB4
Apr 8 22:41:49: --- last message repeated 1 time ---
Apr 8 22:41:49 wslyMac kernel[0]: disk1s2: 0x48 (UNDEFINED).
Apr 8 22:41:50 wslyMac kernel[0]:
Apr 8 22:41:50: --- last message repeated 1 time ---
Apr 8 22:41:50 wslyMac kernel[0]: jnl: disk1s2: dojnlio: strategy err 0x5
Apr 8 22:41:50 wslyMac kernel[0]: jnl: disk1s2: end_transaction: only wrote 0 of 463360 bytes to the journal!
Apr 8 22:41:50 wslyMac kernel[0]: smbiodreconnect: Reconnected to STORAGE-7AB4
Apr 8 22:41:50 wslyMac fseventsd[39]: disk logger: failed to open output file /Volumes/TimeMachine_Backup/.fseventsd/00000000005a57d8 (Invalid argument). mount point /Volumes/TimeMachine_Backup/.fseventsd
Apr 8 22:41:50 wslyMac kernel[0]: smbfssmb_reopenfile: Reopen 1a with open deny modes failed because the modify time has changed was 1239244850s 0ns now 1239244910s 0ns!
Apr 8 22:41:50 wslyMac kernel[0]: smbfssmb_reopenfile: Warning: pid 360(diskimages-helpe) reopening of 1a failed with error 5
Apr 8 22:41:50 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A -AE37-350EFD1764B1)(Error) IndexCI in ci_ftruncate:ftruncate(53 /Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A- AE37-350EFD1764B1/live.0.indexPostings, 131072) error:22
Apr 8 22:41:50 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A -AE37-350EFD1764B1)(Error) IndexCI in initPayload:ftruncate err: 22
Apr 8 22:41:50 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A -AE37-350EFD1764B1)(Error) IndexGeneral in notify_lowspace:low space for device 234881029 (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A -AE37-350EFD1764B1)
Apr 8 22:41:50 wslyMac mds[33]: (Error) Volume: LOW DISK SPACE device:234881029
Apr 8 22:41:50 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A -AE37-350EFD1764B1)(Error) IndexCI in ci_ftruncate:ftruncate(54 /Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A- AE37-350EFD1764B1/live.0.indexPostings, 131072) error:22
Apr 8 22:41:50 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A -AE37-350EFD1764B1)(Error) IndexCI in initPayload:ftruncate err: 22
Apr 8 22:41:50 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/B8028080-DC7D-4A98 -813F-46DA8DCFF8AF)(Error) IndexCI in ci_ftruncate:ftruncate(48 /Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/B8028080-DC7D-4A98- 813F-46DA8DCFF8AF/live.0.indexPostings, 4096) error:22
Apr 8 22:41:50 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/B8028080-DC7D-4A98 -813F-46DA8DCFF8AF)(Error) IndexCI in initPayload:ftruncate err: 22
Apr 8 22:41:50 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A -AE37-350EFD1764B1)(Error) IndexCI in copyFileOrFd:error (22) opening 0.indexGroups
Apr 8 22:41:50 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A -AE37-350EFD1764B1)(Error) IndexCI in recoverIndex:Unrecoverable error: could not recover groups file (0.)
Apr 8 22:41:50 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A -AE37-350EFD1764B1)(Error) IndexCI in CIMetaInfoCreate:Tried to create index when index already existed /Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A- AE37-350EFD1764B1
Apr 8 22:41:50 wslyMac /System/Library/CoreServices/backupd[356]: Error: (-50) SrcErr:NO Copying /Applications/Utilities/System Profiler.app/Contents/version.plist to /Volumes/TimeMachine_Backup/Backups.backupdb/wslyMac/2009-04-08-220327.inProgre ss/0788B97B-3F1C-4331-90E0-7FAE0EDDC3D1/Macintosh HD/Applications/Utilities/System Profiler.app/Contents
Apr 8 22:41:50 wslyMac /System/Library/CoreServices/backupd[356]: Error: (-50) SrcErr:NO Copying /Applications/Utilities/System Profiler.app/Contents to /Volumes/TimeMachine_Backup/Backups.backupdb/wslyMac/2009-04-08-220327.inProgre ss/0788B97B-3F1C-4331-90E0-7FAE0EDDC3D1/Macintosh HD/Applications/Utilities/System Profiler.app
Apr 8 22:41:50 wslyMac /System/Library/CoreServices/backupd[356]: Indexing a file failed. Returned -1132 for: /Applications/Utilities/System Profiler.app, /Volumes/TimeMachine_Backup/Backups.backupdb/wslyMac/2009-04-08-220327.inProgre ss/0788B97B-3F1C-4331-90E0-7FAE0EDDC3D1/Macintosh HD/Applications/Utilities/System Profiler.app
Apr 8 22:41:50 wslyMac /System/Library/CoreServices/backupd[356]: Aborting backup because indexing of file failed.
Apr 8 22:41:50 wslyMac /System/Library/CoreServices/backupd[356]: Stopping backup.
Apr 8 22:41:50 wslyMac /System/Library/CoreServices/backupd[356]: Error: (-50) SrcErr:NO Copying /Applications/Utilities/System Profiler.app to /Volumes/TimeMachine_Backup/Backups.backupdb/wslyMac/2009-04-08-220327.inProgre ss/0788B97B-3F1C-4331-90E0-7FAE0EDDC3D1/Macintosh HD/Applications/Utilities
Apr 8 22:41:50 wslyMac /System/Library/CoreServices/backupd[356]: Copied 1738 files (4.0 GB) from volume Macintosh HD.
Apr 8 22:41:55 wslyMac /System/Library/CoreServices/backupd[356]: Backup canceled.
Apr 8 22:41:56 wslyMac /System/Library/CoreServices/Finder.app/Contents/MacOS/Finder[117]: StatusMonitor::volumesChangedCallBack returned -47
Apr 8 22:42:06: --- last message repeated 1 time ---
Apr 8 22:42:06 wslyMac /System/Library/CoreServices/backupd[356]: Failed to eject volume /Volumes/TimeMachine_Backup (FSVolumeRefNum: -113; status: -47; dissenting pid: 0)
Apr 8 22:42:06 wslyMac /System/Library/CoreServices/Finder.app/Contents/MacOS/Finder[117]: StatusMonitor::volumesChangedCallBack returned -47
Apr 8 22:42:56 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/B8028080-DC7D-4A98 -813F-46DA8DCFF8AF)(Error) IndexCI in ci_ftruncate:ftruncate(43 /Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/B8028080-DC7D-4A98- 813F-46DA8DCFF8AF/live.0.indexIds, 32768) error:22
Apr 8 22:42:56 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/B8028080-DC7D-4A98 -813F-46DA8DCFF8AF)(Error) IndexCI in openindexfile:ftruncate error: 22, size: 32768, live.0.indexIds
Apr 8 22:42:56 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/B8028080-DC7D-4A98 -813F-46DA8DCFF8AF)(Error) IndexCI in ContentIndexOpenBulk:Could not open /Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/B8028080-DC7D-4A98- 813F-46DA8DCFF8AF/live.0.; needs recovery
Apr 8 22:42:56 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/B8028080-DC7D-4A98 -813F-46DA8DCFF8AF)(Error) IndexCI in copyFileOrFd:error (22) opening 0.indexGroups
Apr 8 22:42:56 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/B8028080-DC7D-4A98 -813F-46DA8DCFF8AF)(Error) IndexCI in recoverIndex:Unrecoverable error: could not recover groups file (0.)
Apr 8 22:42:56 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/B8028080-DC7D-4A98 -813F-46DA8DCFF8AF)(Error) IndexCI in CIMetaInfoCreate:Tried to create index when index already existed /Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/B8028080-DC7D-4A98- 813F-46DA8DCFF8AF
Apr 8 22:42:56 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A -AE37-350EFD1764B1)(Error) IndexCI in copyFileOrFd:error (22) opening 0.indexGroups
Apr 8 22:42:56 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A -AE37-350EFD1764B1)(Error) IndexCI in recoverIndex:Unrecoverable error: could not recover groups file (0.)
Apr 8 22:42:56 wslyMac mds[33]: (/Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A -AE37-350EFD1764B1)(Error) IndexCI in CIMetaInfoCreate:Tried to create index when index already existed /Volumes/TimeMachine_Backup/.Spotlight-V100/Store-V1/Stores/DE7D5030-E962-480A- AE37-350EFD1764B1
Apr 8 22:50:21 localhost kernel[0]: npvhash=4095
Apr 8 22:50:17 localhost com.apple.launchctl.System[2]: fsck_hfs: Volume is journaled. No checking performed.
Apr 8 22:50:17 localhost com.apple.launchctl.System[2]: fsck_hfs: Use the -f option to force checking.
Apr 8 22:50:21 localhost com.apple.launchctl.System[2]: launchctl: Please convert the following to launchd: /etc/mach_init.d/dashboardadvisoryd.plist
Apr 8 22:50:21 localhost com.apple.launchd[1] (com.apple.blued): Unknown key for boolean: EnableTransactions
Apr 8 22:50:21 localhost com.apple.launchd[1] (org.cups.cupsd): Unknown key: SHAuthorizationRight
Apr 8 22:50:21 localhost com.apple.launchd[1] (org.ntp.ntpd): Unknown key: SHAuthorizationRight
Apr 8 22:50:21 localhost DirectoryService[11]: Launched version 5.6 (v514.24)
Apr 8 22:50:27 localhost kernel[0]: hi mem tramps at 0xffe00000
Apr 8 22:50:22 localhost DirectoryService[11]: Improper shutdown detected
Apr 8 22:50:27 localhost kernel[0]: PAE enabled
Apr 8 22:50:27 localhost kernel[0]: 64 bit mode enabled
Apr 8 22:50:27 localhost kernel[0]: Darwin Kernel Version 9.6.0: Mon Nov 24 17:37:00 PST 2008; root:xnu-1228.9.59~1/RELEASE_I386
Apr 8 22:50:27 localhost kernel[0]: standard timeslicing quantum is 10000 us
Apr 8 22:50:27 localhost kernel[0]: vmpagebootstrap: 511374 free pages and 12914 wired pages
Apr 8 22:50:27 localhost kernel[0]: migtable_maxdispl = 79
Apr 8 22:50:22 localhost kextd[10]: 417 cached, 0 uncached personalities to catalog
Apr 8 22:50:27 localhost kernel[0]: 101 prelinked modules
Apr 8 22:50:27 localhost kernel[0]: AppleACPICPU: ProcessorApicId=0 LocalApicId=0 Enabled
Apr 8 22:50:27 localhost kernel[0]: AppleACPICPU: ProcessorApicId=1 LocalApicId=1 Enabled
Apr 8 22:50:27 localhost kernel[0]: Loading security extension com.apple.security.TMSafetyNet
Apr 8 22:50:27 localhost kernel[0]: calling mpopolicyinit for TMSafetyNet
Apr 8 22:50:27 localhost kernel[0]: Security policy loaded: Safety net for Time Machine (TMSafetyNet)
Apr 8 22:50:27 localhost kernel[0]: Loading security extension com.apple.nke.applicationfirewall
Apr 8 22:50:27 localhost kernel[0]: Loading security extension com.apple.security.seatbelt
Apr 8 22:50:27 localhost kernel[0]: calling mpopolicyinit for mb
Apr 8 22:50:27 localhost kernel[0]: Seatbelt MACF policy initialized
Apr 8 22:50:27 localhost kernel[0]: Security policy loaded: Seatbelt Policy (mb)
Apr 8 22:50:27 localhost kernel[0]: Copyright (c) 1982, 1986, 1989, 1991, 1993
Apr 8 22:50:27 localhost kernel[0]: The Regents of the University of California. All rights reserved.
Apr 8 22:50:27 localhost kernel[0]: MAC Framework successfully initialized
Apr 8 22:50:27 localhost kernel[0]: using 10485 buffer headers and 4096 cluster IO buffer headers
Apr 8 22:50:27 localhost kernel[0]: IOAPIC: Version 0x20 Vectors 64:87
Apr 8 22:50:27 localhost kernel[0]: ACPI: System State [S0 S3 S4 S5] (S3)
Apr 8 22:50:27 localhost kernel[0]: mbinit: done
Apr 8 22:50:27 localhost kernel[0]: Security auditing service present
Apr 8 22:50:27 localhost kernel[0]: BSM auditing present
Apr 8 22:50:27 localhost kernel[0]: rooting via boot-uuid from /chosen: 402D8D77-0836-3192-8A63-554D726141DC
Apr 8 22:50:27 localhost kernel[0]: Waiting on <dict ID="0"><key>IOProviderClass</key><string ID="1">IOResources</string><key>IOResourceMatch</key><string ID="2">boot-uuid-media</string></dict>
Apr 8 22:50:27 localhost kernel[0]: FireWire (OHCI) TI ID 8025 built-in now active, GUID 001e52fffe3817fa; max speed s800.
Apr 8 22:50:27 localhost kernel[0]: Got boot device = IOService:/AppleACPIPlatformExpert/PCI0/AppleACPIPCI/SATA@1F,2/AppleICH8AHCI/PR T0@0/IOAHCIDevice@0/AppleAHCIDiskDriver/IOAHCIBlockStorageDevice/IOBlockStorageD river/FUJITSU MHY2120BH Media/IOGUIDPartitionScheme/Customer@2
Apr 8 22:50:27 localhost kernel[0]: BSD root: disk0s2, major 14, minor 2
Apr 8 22:50:27 localhost kernel[0]: jnl: unknown-dev: replay_journal: from: 15129600 to: 2979328 (joffset 0x7d01000)
Apr 8 22:50:27 localhost kernel[0]: [Bluetooth::CSRHIDTransition] switchToHCIMode (legacy)
Apr 8 22:50:27 localhost kernel[0]: [Bluetooth::CSRHIDTransition] transition complete.
Apr 8 22:50:27 localhost kernel[0]: [HCIController][configurePM] power parent ready after 1 tries
Apr 8 22:50:27 localhost kernel[0]: AppleIntelCPUPowerManagement: initialization complete
Apr 8 22:50:27 localhost kernel[0]: jnl: unknown-dev: journal replay done.
Apr 8 22:50:27 localhost kernel[0]: HFS: Removed 4 orphaned unlinked files or directories
Apr 8 22:50:27 localhost kernel[0]: Jettisoning kernel linker.
Apr 8 22:50:27 localhost kernel[0]: Resetting IOCatalogue.
Apr 8 22:50:27 localhost kernel[0]: GFX0: family specific matching fails
Apr 8 22:50:27 localhost kernel[0]: Matching service count = 1
Apr 8 22:50:27 localhost kernel[0]: Matching service count = 2
Apr 8 22:50:27: --- last message repeated 4 times ---
Apr 8 22:50:27 localhost kernel[0]: Previous Shutdown Cause: 5
Apr 8 22:50:27 localhost kernel[0]: NVDANV50HAL loaded and registered.
Apr 8 22:50:27 localhost kernel[0]: GFX0: family specific matching fails
Apr 8 22:50:27 localhost kernel[0]: ath_attach: devid 0x24
Apr 8 22:50:27 localhost kernel[0]: Override HT40 CTL Powers. EEPROM Version is 14.4, Device Type 5
Apr 8 22:50:27 localhost kernel[0]: mac 12.10 phy 8.1 radio 12.0
Apr 8 22:50:27 localhost kernel[0]: GFX0: family specific matching fails
Apr 8 22:50:27: --- last message repeated 1 time ---
Apr 8 22:50:27 localhost kernel[0]: Matching service count = 0
Apr 8 22:50:27 localhost kernel[0]: yukon: Ethernet address 00:1b:63:b3:0d:6b
Apr 8 22:50:27 localhost kernel[0]: AirPort_Athr5424ab: Ethernet address 00:1e:52:71:2c:52
Apr 8 22:50:30 localhost mDNSResponder mDNSResponder-176.3 (Sep 30 2008 16:59:38)[16]: starting
Apr 8 22:50:30 localhost fseventsd[38]: event logs in /.fseventsd out of sync with volume. destroying old logs. (3603 22 3778)
Apr 8 22:50:30 localhost rpc.statd[30]: statd.notify - no notifications needed
Apr 8 22:50:31 localhost kernel[0]: AirPort: Link Down on en1
Apr 8 22:50:30 localhost /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[33]: Login Window Application Started -- Threaded auth
Apr 8 22:50:30 localhost fseventsd[38]: log dir: /.fseventsd getting new uuid: B621E1D8-11D5-49D5-90F5-6E32BEDC8615
Apr 8 22:50:30 localhost bootlog[45]: BOOT_TIME: 1239241808 0
Apr 8 22:50:30 localhost blued[46]: Apple Bluetooth daemon started.
Apr 8 22:50:31 wslyMac configd[14]: setting hostname to "wslyMac.local"
Apr 8 22:50:33 wslyMac kernel[0]: AppleYukon2 - en0 link active, 100-Mbit, full duplex, symmetric flow control enabled port 0
Apr 8 22:50:35 wslyMac org.ntp.ntpd[26]: Error : nodename nor servname provided, or not known
Apr 8 22:50:35 wslyMac ntpdate[60]: can't find host time.apple.com
Apr 8 22:50:35 wslyMac ntpdate[60]: no servers can be used, exiting
Apr 8 22:50:39 wslyMac kernel[0]: IOHIDSystem: Seize of IOHIDPointing failed.
Apr 8 22:50:39 wslyMac kernel[0]: IOHIDSystem: Seize of IOHIDEventDriver failed.
Apr 8 22:50:39 wslyMac kextd[10]: writing kernel link data to /var/run/mach.sym
Apr 8 22:50:43 wslyMac /usr/sbin/ocspd[75]: starting
Apr 8 22:50:43 wslyMac com.apple.SystemStarter[28]: Starting HP IO Monitor
Apr 8 22:50:43 wslyMac com.apple.SystemStarter[28]: Starting HP Trap Monitor
Apr 8 22:50:43 wslyMac com.apple.SystemStarter[28]: /Library/StartupItems/HP Trap Monitor/HP Trap Monitor: line 15: /Library/Printers/hp/hpio/HPIO Trap Monitor.app/Contents/MacOS/HPIO Trap Monitor: No such file or directory
Apr 8 22:50:46 wslyMac loginwindow[33]: Login Window Started Security Agent
Apr 8 22:52:36 wslyMac authorizationhost[95]: MechanismInvoke 0x125de0 retainCount 2
Apr 8 22:52:36 wslyMac SecurityAgent[96]: MechanismInvoke 0x101660 retainCount 1
Apr 8 22:52:37 wslyMac SecurityAgent[96]: NSSecureTextFieldCell detected a field editor ((null)) that is not a NSTextView subclass designed to work with the cell. Ignoring...
Apr 8 22:52:37 wslyMac loginwindow[33]: Login Window - Returned from Security Agent
Apr 8 22:52:37 wslyMac SecurityAgent[96]: MechanismDestroy 0x101660 retainCount 1
Apr 8 22:52:37 wslyMac authorizationhost[95]: MechanismDestroy 0x125de0 retainCount 2
Apr 8 22:52:37 wslyMac loginwindow[33]: USER_PROCESS: 33 console
Apr 8 22:52:37 wslyMac com.apple.launchd[1] (com.apple.UserEventAgent-LoginWindow[91]): Exited: Terminated
Apr 8 22:52:37 wslyMac com.apple.launchd[108] (com.apple.AirPortBaseStationAgent): Unknown key for boolean: EnableTransactions
Apr 8 22:52:42 wslyMac Dock[118]: _DESCRegisterDockExtraClient failed 268435459
Apr 8 22:52:44 wslyMac /System/Library/CoreServices/coreservicesd[56]: SFLSharePointsEntry::CreateDSRecord: dsCreateRecordAndOpen(wsly Hiroyuki Mompean Ueda's Public Folder) returned -14135
Apr 8 22:53:02 wslyMac /System/Library/CoreServices/SystemUIServer.app/Contents/MacOS/SystemUIServer[1 24]: CPSGetProcessInfo(): This call is deprecated and should not be called anymore.
Apr 8 22:53:02 wslyMac /System/Library/CoreServices/SystemUIServer.app/Contents/MacOS/SystemUIServer[1 24]: CPSPBGetProcessInfo(): This call is deprecated and should not be called anymore.
Apr 8 22:54:42 wslyMac kernel[0]: AppleYukon2 - en0 link down
Apr 8 22:54:46 wslyMac kernel[0]: AppleYukon2 - en0 link active, 100-Mbit, full duplex, symmetric flow control enabled port 0
Apr 8 22:54:52 wslyMac kernel[0]: AppleYukon2 - en0 link down
Apr 8 22:54:53 wslyMac kernel[0]: AppleYukon2 - en0 link active, 100-Mbit, full duplex, symmetric flow control enabled port 0

I've had this problem with this computer as soon as I remember starting to use it.
You should have taken it back to apple immediately.
You need to try a clean install of the OS.. yosemite has known bugs especially with the wireless and if you upgrade installed the OS it can just get worse.
You should do a clone of the hard disk and a Time Machine backup etc.. to make sure you don't lose files.. but a clean install will at least show if it is driver issue or actual faulty hardware. Is the laptop still in warranty / Applecare.. if so return it to apple for checking.

Rule for Control Plane traffic Transparent Firewall

Hi Everyone,
ASA working in routed mode traffic is allowed by default from high security inside to low security outside.
But in case of transparent firewall control plane traffic from inside to outside it is not allowed by default.
Need to know the reason behind this?
IS this due to transparent firewall layer 2?
Regards
MAhesh

Hello Chintan,
the VRF access link where the CE is connected is part of the VRF and isn't a member of the Global Routing Table anymore.
So any possible attempt to build an LDP session cannot impact on the backbone MPLS control plane.
If you want to specify all the acceptable LDP sources in a receive-ACL or in Control plane policing as part of a security plan that will be another matter.
Only on Carrier Supporting Carrier scenario you have an MPLS LDP or BGPv4 with labels session between PE and CE.
Hope to help
Giuseppe

Control Plan ..

Hi,
Guide me with the usage of Control Plan (Transcation QPCP) ?
Please shae docs iff possible //

Hi Mayank,
I personally have not implemented CP in any project, but have a good link that am sharing with you.
Link : {http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/0063c232-199e-2c10-5482-eed82c19b416?quicklink=index&overridelayout=true]

Control Plan for FMEA

Hi,
I created control plan using QPCP transaction. I clicked on FMEA Tab and assigned the FMEA in the control plan. The traffic light status is coming in red. Kindly let me know where i am going wrong.
Regards,
Pragalathan

Hi,
This is because of Non transfer of Characteristics from FMEA to Control Plan...
Refer below link for process:
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/0063c232-199e-2c10-5482-eed82c19b416?quicklink=index&overridelayout=true
Check & revert.
Regards,
Anup

Not able to access the links to Essbase Console, Planning and Shared Servic

Hi,
I am trying to access the links to Essbase Console, Planning and Shared Services but I get the following error message.
Error 404--Not Found
From RFC 2068 Hypertext Transfer Protocol -- HTTP/1.1:
10.4.5 404 Not Found
The server has not found anything matching the Request-URI. No indication is given of whether the condition is temporary or permanent.
If the server does not wish to make this information available to the client, the status code 403 (Forbidden) can be used instead. The 410 (Gone) status code SHOULD be used if the server knows, through some internally configurable mechanism, that an old resource is permanently unavailable and has no forwarding address.
I tried to restart all the services on all the servers and also restarted the servers but it didn't work.
I found some more errors in the starter file on the Linux box.
{\rtf1\ansi\ansicpg1252\deff0\deflang1033{\fonttbl{\f0\fswiss\fcharset0 Arial;}}
{\*\generator Msftedit 5.41.15.1515;}\viewkind4\uc1\pard\f0\fs20 Detected Java version: 1.6 in: /srv/Oracle/Middleware/jdk160_21/jre\par
Detected OS: Linux\par
parsing buildfile /srv/Oracle/Middleware/EPMSystem11R1/common/config/11.1.2.0/resources/instance/start.xml with URI = file:/s\par
rv/Oracle/Middleware/EPMSystem11R1/common/config/11.1.2.0/resources/instance/start.xml\par
Project base dir set to: /srv/Oracle/Middleware/EPMSystem11R1/common/config/11.1.2.0/resources/instance\par
[antlib:org.apache.tools.ant] Could not load definitions from resource org/apache/tools/ant/antlib.xml. It could not be found\par
.\par
[property] Loading Environment env.\par
Build sequence for target(s) `start' is [start]\par
Complete build sequence is [start, stop, ]\par
\par
start:\par
[starter] oracle.as.management.opmn.optic.OpticException: Error in starting opmn server\par
[starter] Operation aborted because of a system call failure or internal error\par
[starter] at oracle.as.management.opmn.optic.OpmnAdmin.executeCommand(OpmnAdmin.java:310)\par
[starter] at oracle.as.management.opmn.optic.OpmnAdmin.startOpmnServer(OpmnAdmin.java:87)\par
[starter] at com.hyperion.cis.ant.starter.OPMNStarter.startAndReloadOpmnCtl(OPMNStarter.java:177)\par
[starter] at com.hyperion.cis.ant.starter.OPMNStarter.init(OPMNStarter.java:47)\par
[starter] at com.hyperion.cis.ant.starter.StarterEngine.load(StarterEngine.java:133)\par
[starter] at com.hyperion.cis.ant.starter.StarterEngine.execute(StarterEngine.java:105)\par
[starter] at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:288)\par
[starter] at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)\par
[starter] at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)\par
[starter] at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)\par
[starter] at java.lang.reflect.Method.invoke(Method.java:597)\par
[starter] at org.apache.tools.ant.dispatch.DispatchUtils.execute(DispatchUtils.java:106)\par
[starter] at org.apache.tools.ant.Task.perform(Task.java:348)\par
[starter] at org.apache.tools.ant.Target.execute(Target.java:357)\par
[starter] at org.apache.tools.ant.Target.performTasks(Target.java:385)\par
[starter] at org.apache.tools.ant.Project.executeSortedTargets(Project.java:1337)\par
[starter] at org.apache.tools.ant.Project.executeTarget(Project.java:1306)\par
[starter] at org.apache.tools.ant.helper.DefaultExecutor.executeTargets(DefaultExecutor.java:41)\par
[starter] at org.apache.tools.ant.Project.executeTargets(Project.java:1189)\par
[starter] at org.apache.tools.ant.Main.runBuild(Main.java:758)\par
[starter] at org.apache.tools.ant.Main.startAnt(Main.java:217)\par
[starter] at org.apache.tools.ant.launch.Launcher.run(Launcher.java:257)\par
[starter] at org.apache.tools.ant.launch.Launcher.main(Launcher.java:104)\par
[starter] oracle.as.management.opmn.optic.OpticBadXMLConfigException: Error reading formFactorFile: /srv/Oracle/Middleware/\par
user_projects/epmsystem6/config/OPMN/opmn/.formfactor (/srv/Oracle/Middleware/user_projects/epmsystem6/config/OPMN/opmn/.form\par
factor (No such file or directory))\par
[starter] at oracle.as.management.opmn.optic.OpmnPhone.refreshFormFactor(OpmnPhone.java:628)\par
[starter] at oracle.as.management.opmn.optic.OpmnPhone.getLocalOpmnPhone(OpmnPhone.java:99)\par
[starter] at oracle.as.management.opmn.optic.OpmnQuery.getLocalOpmnQuery(OpmnQuery.java:77)\par
[starter] at com.hyperion.cis.ant.starter.OPMNStarter.init(OPMNStarter.java:48)\par
[starter] at com.hyperion.cis.ant.starter.StarterEngine.load(StarterEngine.java:133)\par
[starter] at com.hyperion.cis.ant.starter.StarterEngine.execute(StarterEngine.java:105)\par
[starter] at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:288)\par
[starter] at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)\par
[starter] at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)\par
[starter] at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)\par
[starter] at java.lang.reflect.Method.invoke(Method.java:597)\par
[starter] at org.apache.tools.ant.dispatch.DispatchUtils.execute(DispatchUtils.java:106)\par
[starter] at org.apache.tools.ant.Task.perform(Task.java:348)\par
[starter] at org.apache.tools.ant.Target.execute(Target.java:357)\par
[starter] at org.apache.tools.ant.Target.performTasks(Target.java:385)\par
[starter] at org.apache.tools.ant.Project.executeSortedTargets(Project.java:1337)\par
[starter] at org.apache.tools.ant.Project.executeTarget(Project.java:1306)\par
[starter] at org.apache.tools.ant.helper.DefaultExecutor.executeTargets(DefaultExecutor.java:41)\par
[starter] at org.apache.tools.ant.Project.executeTargets(Project.java:1189)\par
[starter] at org.apache.tools.ant.Main.runBuild(Main.java:758)\par
[starter] at org.apache.tools.ant.Main.startAnt(Main.java:217)\par
[starter] at org.apache.tools.ant.launch.Launcher.run(Launcher.java:257)\par
[starter] at org.apache.tools.ant.launch.Launcher.main(Launcher.java:104)\par
[starter] Caused by: java.io.FileNotFoundException: /srv/Oracle/Middleware/user_projects/epmsystem6/config/OPMN/opmn/.formf\par
actor (No such file or directory)\par
[starter] at java.io.FileInputStream.open(Native Method)\par
[starter] at java.io.FileInputStream.<init>(FileInputStream.java:106)\par
[starter] at java.io.FileReader.<init>(FileReader.java:55)\par
[starter] at oracle.as.management.opmn.optic.OpmnPhone.refreshFormFactor(OpmnPhone.java:623)\par
[starter] ... 22 more\par
( Feb 06, 2012 04.33.13 PM ) Pass [00 min 05 sec] Starting BPMS_bpms1_Server\par
[starter] oracle.as.management.opmn.optic.OpticException: Error in starting opmn server\par
[starter] Operation aborted because of a system call failure or internal error\par
[starter] at oracle.as.management.opmn.optic.OpmnAdmin.executeCommand(OpmnAdmin.java:310)\par
[starter] at oracle.as.management.opmn.optic.OpmnAdmin.startOpmnServer(OpmnAdmin.java:87)\par
[starter] at com.hyperion.cis.ant.starter.OPMNStarter.startAndReloadOpmnCtl(OPMNStarter.java:177)\par
[starter] at com.hyperion.cis.ant.starter.OPMNStarter.start(OPMNStarter.java:115)\par
[starter] at com.hyperion.cis.ant.starter.StarterEngine.start(StarterEngine.java:190)\par
[starter] at com.hyperion.cis.ant.starter.StarterEngine.execute(StarterEngine.java:112)\par
[starter] at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:288)\par
[starter] at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)\par
[starter] at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)\par
[starter] at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)\par
[starter] at java.lang.reflect.Method.invoke(Method.java:597)\par
[starter] at org.apache.tools.ant.dispatch.DispatchUtils.execute(DispatchUtils.java:106)\par
[starter] at org.apache.tools.ant.Task.perform(Task.java:348)\par
[starter] at org.apache.tools.ant.Target.execute(Target.java:357)\par
[starter] at org.apache.tools.ant.Target.performTasks(Target.java:385)\par
[starter] at org.apache.tools.ant.Project.executeSortedTargets(Project.java:1337)\par
[starter] at org.apache.tools.ant.Project.executeTarget(Project.java:1306)\par
[starter] at org.apache.tools.ant.helper.DefaultExecutor.executeTargets(DefaultExecutor.java:41)\par
[starter] at org.apache.tools.ant.Project.executeTargets(Project.java:1189)\par
[starter] at org.apache.tools.ant.Main.runBuild(Main.java:758)\par
[starter] at org.apache.tools.ant.Main.startAnt(Main.java:217)\par
[starter] at org.apache.tools.ant.launch.Launcher.run(Launcher.java:257)\par
[starter] at org.apache.tools.ant.launch.Launcher.main(Launcher.java:104)\par
( Feb 06, 2012 04.33.31 PM ) Pass [00 min 05 sec] Starting OHS\par
( Feb 06, 2012 04.41.51 PM ) Fail [08 min 20 sec] Starting FoundationServices\par
\par
BUILD SUCCESSFUL\par
Total time: 8 minutes 55 seconds\par
Please let me know how to fix this issue. Also please let me know where else can I find the logs to the errors.
Thanks.

The logs would be a good place to start, if you are not sure where to look post your OS and planning version.
Cheers
John
http://john-goodwin.blogspot.com/

How can I activate drill down report for planned line items please urgent?

Hi Everyone,
Please suggest me how can i activate drill down report for planned line items in internal orders. S_ALR_87012993. Please suggest me, I'll award full points. I am unable to do it in client system, which has already line items. I tried in my sys with new config it is working.
Kind regards
Arvey.

Hi
It is based on the reports attached in the Report Group - TCODE: GR53
In the Report Group screen
Press CONFIGURE This is to attach any Drill Down reports.
Press the Insert Line icon
As is the screen may be used to insert a Report Writer report group. To add an ABAP, press other report type
Double click on ABAP Reports
Enter the name of the ABAP and ENTER
<b>RCOPCA08 Profit Center: Plan Line Items</b>
VVR

Occasional problem with eth0 link down after booting

Hi,
Every so often after booting up the PC there is not any working network connection. Looking through the output of dmesg, I find "eth0 link down" messages. Not knowing a lot about networking lead me to resort to rebooting to resolve the problem, and rebooting does indeed resolve the problem. Today I discovered the post at [url http://bbs.archlinux.org/viewtopic.php?id=117728] which suggests similar behaviour.
I played around with ifconfig and initially thought I was seeing the same behaviour, but believe I was mistaken. I can't actually confirm until it happens if my new found knowledge will actually resolve the problem without rebooting.
I'd like to try and track down the source of the problem, and either file a bug report or take some other (configuration) measure, but need help tracing it.
Hardware in question is: Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
and I'm using the testing repository in Arch. Any help appreciated.
Cheers,
James.

I have the exact same problem and I have the exact same ethernet controller/chip.
I've not looked that much why it was doing this. Maybe auto-negotiation fail for I don't know which reason, maybe something else, hard to tell. I might try to investigate this a bit more next time it does me this.
That said, what I'm doing when I'm seeing that my eth0 has no carrier, I'm doing a "ip link set eth0 down", wait a few seconds, and then a "ip link set eth0 up", and then it's usually fine. Since I'm personally using static IP addresses, I also have to re-add the default route after that, i.e. a "ip route add default via 192.168.1.1" to be able to go out of my LAN again. This will be different if you are using DHCP.

Link down on Oracle 10R2 - RAC

Dear All..
This is my first post, I have question related with RAC environment.
I setting up RAC on spesifications bellow:
- 3 HP server using intel xeon and 4G RAM each.
- Hitachi SAN
- Linux Centos 4.2
- Oracle 10g Release 2
- ASM 2 and OCFS 2
In installation steps, I found no problems. And the IP configuration used are:
# Public Network - (eth0)
172.20.141.1 linux1
172.20.141.2 linux2
172.20.141.3 linux3
# Private Interconnect - (eth1)
192.168.0.1 int-linux1
192.168.0.2 int-linux2
192.168.0.3 int-linux3
# Public Virtual IP (VIP) addresses for - (eth0)
172.20.142.1 vip-linux1
172.20.142.2 vip-linux2
172.20.142.3 vip-linux3
==========================================
Hangcheck 30 seconds, margin is 180 seconds
==========================================
[root@linux2 ~]# grep Hangcheck /var/log/messages |
tail -5
Apr 24 13:09:59 linux2 kernel: Hangcheck: starting
hangcheck timer 0.5.0 (tick is 30 seconds, margin is
180 seconds).
Apr 25 13:24:42 linux2 kernel: Hangcheck: starting
hangcheck timer 0.5.0 (tick is 30 seconds, margin is
180 seconds).
==========================================
setup O2CB_HEARTBEAT_THRESHOLD=301 pada file
/etc/sysconfig/o2cb
==========================================
But when I am trying to test the server using very hard
environment test (transactions and reporting using application
build by Delphi), just likes production ones, I found an error
occurred, eth0 : link down. The times it happen was random
(1 month 3 times - averages values).
And this is the error log.
==========================================
linux2 error log
==========================================
Apr 22 07:55:01 linux2 crond(pam_unix)[4288]: session
closed for user root
Apr 22 07:55:18 linux2 kernel: eth0: link down
Apr 22 07:55:19 linux2 kernel: eth0: link up, 100Mbps,
full-duplex, lpa 0x45E1
Apr 22 07:55:24 linux2 kernel:
(0,0):o2net_idle_timer:1330 connection to node li
nux3 num 1 at 172.20.141.3:7777 has been idle for 10
seconds, shutting it down.
Apr 22 07:55:24 linux2 kernel:
(0,0):o2net_idle_timer:1341 here are some times t
hat might help debug the situation: (tmr
1145667314.798878 now 1145667324.796791
dr 1145667314.798856 adv
1145667314.798892:1145667314.798893 func (c9943f19:505
) 1145429443.839194:1145429443.839197)
Apr 22 07:55:24 linux2 kernel:
(2248,1):o2net_set_nn_state:421 no longer connect
ed to node linux3 at 172.20.141.3:7777
Apr 22 07:55:26 linux2 kernel:
(0,0):o2net_idle_timer:1330 connection to node li
nux1 num 2 at 172.20.141.1:7777 has been idle for 10
seconds, shutting it down.
Apr 22 07:55:26 linux2 kernel:
(0,0):o2net_idle_timer:1341 here are some times t
hat might help debug the situation: (tmr
1145667316.353964 now 1145667326.352424
dr 1145667316.353945 adv
1145667316.353965:1145667316.353966 func (c9943f19:505
) 1145429355.325673:1145429355.325679)
Apr 22 07:55:26 linux2 kernel:
(2248,1):o2net_set_nn_state:421 no longer connect
ed to node linux1 at 172.20.141.1:7777
============================================
linux1 error log
============================================
Apr 22 07:55:02 linux1 crond(pam_unix)[10395]: session
closed for user root
Apr 22 07:57:58 linux1 kernel:
(2319,0):o2net_set_nn_state:421 no longer connect
ed to node linux2 at 172.20.141.2:7777
===========================================
linux3 error log
===========================================
Apr 22 07:55:03 linux3 crond(pam_unix)[14329]: session
closed for user root
Apr 22 07:56:50 linux3 kernel:
(2512,0):o2net_set_nn_state:421 no longer connect
ed to node linux2 at 172.20.141.2:7777
Any body have an advice or solution to overcome this problem.
Thanks for helping.
Best Regards,
Car Elcaro.

$cat opmn/conf/ons.config
localport=6101
remoteport=6200
loglevel=9
useocr=on
2007-02-09 13:43:16.441: [    RACG][1] [15217][1][ora.cgwdb02.ons]: Number of onsconfiguration retrieved, numcfg = 2
onscfg[0]
{node = cgwdb01, port = 6200}
Adding remote host cgwdb01:6200
onscfg[1]
{node = cgwdb02, port = 6200}
Adding remote host cgwdb02:6200
ons is not running ...
2007-02-09 13:43:16.454: [    RACG][1] [15217][1][ora.cgwdb02.ons]: clsrcexecut: env ORACLE_CONFIG_HOME=/u01/oracle/product/10.2.0/crs
2007-02-09 13:43:16.454: [    RACG][1] [15217][1][ora.cgwdb02.ons]: clsrcexecut: cmd = /u01/oracle/product/10.2.0/crs/bin/racgeut -e USRORA_DEBUG=0 540 /u01/oracle/product/10.2.0/crs/bin/onsctl ping
2007-02-09 13:43:16.454: [    RACG][1] [15217][1][ora.cgwdb02.ons]: clsrcexecut: rc = 1, time = 0.531s
2007-02-09 13:43:16.454: [    RACG][1] [15217][1][ora.cgwdb02.ons]: end for resource = ora.cgwdb02.ons, action = check, status = 1, time = 0.743s
2007-02-09 13:43:17.421: [    RACG][1] [15239][1][ora.cgwdb02.ons]: onsctl: shutting down ons daemon ...
Number of onsconfiguration retrieved, numcfg = 2
onscfg[0]
{node = cgwdb01, port = 6200}
Adding remote host cgwdb01:6200
onscfg[1]
{node = cgwdb02, port = 6200}
Adding remote host cgwdb02:6200

Srw224g4 fiber link down

Support,
Yesterday for no apparent reason the fiber link between my SRW224G4 and SLM248G went down. Luckily I have a backup SRW224 switch with a mini-GBIC. I tried both ports on the SRW224G4 switch. Neither would sync with the SLM248G switch. I moved the mini-GBIC to the SRW224 switch. This got the network back up.
Why did not SRW224G4 switch fail? I've looked through the logs and only see link down entries. Is there a way to test the switch to see why it failed? Do I need to relpace the switch? Is it still under warranty? What are my options??
Thanks,
Bill V

i've checked the datasheet for the device and the warranty period is 5 years. you already tried to use a different mini-gbic card for the device, right? i suggest that you try to swap the gbic card also to verify if that will work.

Solaris 8 says: "Link down, Cable Problem?"

I have these on my home LAN:
1. Sun Ultra 5 Solaris 8
2. Win 2000 PC
3. Win NT laptop
They are all hooked into a LinkSys Router.
The Router is hooked into my Motorala Cable Modem.
Here's the problem:
The PC and the laptop can see each other on the LAN.
The Solaris 8 is only visible on the Lan INTERMITTENTLY.
The lights on the Router for the PC and laptop are always ON.
When I reboot the Solaris box, the lights on the Router sometimes come ON, and sometimes they stay OFF. When they stay OFF, I see the message: "Link down, Cable Problem?" during reboot.
I have tried different cables, and tried various combinations of the 4 avalable ports on the back of my Router.
If I plug in the Sun box DIRECTLY into my cable modem, then I don't see the above message. (but then I don't have a LAN anymore)
Please help, I've been struggling with this for a while now.
Thanks,
Irshad Ahmed (I am relatively new to Sun)

Hi
You have not indicated if you have the router ethernet ports working
at 100Mbps or 10Mbps. Depending on this sometimes, Sun systems may
not be correctly auto-negotiating their ethernet port settings.
You may set these parameters to force Sun Ultra 5 to a 100Mbps mode or a 10Mbps mode.
For forcing it to 100Mbps, Full Duplex mode and disabling the auto-negotiation, put these entries in /etc/system:
set hme:hme_adv_autoneg_cap=0
set hme:hme_adv_100T4_cap=0
set hme:hme_adv_100fdx_cap=1
set hme:hme_adv_100hdx_cap=0
set hme:hme_adv_10fdx_cap=0
set hme:hme_adv_10hdx_cap=0
Conversely, if you want to force your Sun to work on 10Mbps, Full
duplex mode, (if your router does not support 100Mbps) in the same
/etc/system file, put the following entries :
set hme:hme_adv_autoneg_cap=0
set hme:hme_adv_100T4_cap=0
set hme:hme_adv_100fdx_cap=0
set hme:hme_adv_100hdx_cap=0
set hme:hme_adv_10fdx_cap=1
set hme:hme_adv_10hdx_cap=0
One of these should solve your problem. You need to reboot the system
after putting these entries.
You can also check the port at the OK prompt using the command
"watch-net". This test the onboard ethernet interface.
You may also apply the hme patch released by Sun that fixes many
known problems with hme ethernet driver. The patch id is 108981-03.
It is available from the site :
http://sunsolve.sun.com
HTH
Shridhar
Sun-DTS

Value drop down list control in ADOBE Form

We are on SP16 currently. We are developing an ADOBE interactive online
form using ABAP WebDynpro.
To display search help of a few fields like Vendor Number, G/L Account
Number, Cost Center, we are using 'Value Help Drop Down List' control
availalbe in WebDynpro Native group.
After the form gets loaded on the broswer, first time the search help
control works absolutely fine for any of the field. But only once. Once
one search help gets displayed, none of the other search value drop
down control gets clicked. But please note that normal drop down (with
fixed values) gets clicked and allows to choose any entry from it. It
also allows to enter values into other text box controls. Only Search
Value Drop Down list stops working.
For Example: We have 2 search help drop down list controls (one for
LIFNR and another for WERKS) and 1 drop down list control (Fixed Values
to be displayed for selection).
After form gets displayed on ABAP WebDynpro, if we click on LIFNR, the
search help for LIFNR will come and it will allow to select vendor
number from it. But after that, it doesn't allow to select WERKS nor
even to LIFNR. If we click on WERKS first, it will work perfactly fine
but then, it will not allow LIFNR or WERKS after that. In any of the
case, it will always allow to select the values from Fixed Value Drop
down list.
Please note that we dont have SAP Portal into the landscape.
Is there any bug in the control?
Please provide the solution ASAP.

Hi Reema,
We are using ZCI type of form. So, I dont think there is any need to run the report for ZCI_Update.
And the display type of Interactive Form in ABAP WebDynpro is 'NATIVE' which is the same we dragged the control from (WebDynpro Native).
Is there any work around to display search helps on ADOBE Interactive forms apart of this control?
Appreciate your quick answer.
Thanks & Regardss,
Sandip Kamdar

Link down on control plane

Similar Messages

Maybe you are looking for