Link switches with fiber.

I have two cisco switches with 2 GBIC ports each. I want to link them with fiber.
I have two ws-g5484 that was gave to me. What else do I need to link these switches?
Do I need media converters and if so how many.
Thank You
Bo Hunter

Media converters are necessary only when your switch does not have the correct fiber interface available.
Make sure the GBIC you have is compatible with your switch using the link below.
GE GBIC Compatibility Matrix
<http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6981.html>
Also, make sure your fiber is multimode (MMF) and that the link length meets the specs outlined in the data sheet, based on the fiber type:
GE GBIC Data Sheet
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6577/product_data_sheet09186a008014cb5e.html
Let us know if you have additional questions.
Tom

Similar Messages

  • Connect 2 switch with fiber

    Hi everybody,
    I´m trying connect two catalyst 3560 Catalyst switch through fiber.  I have a network in the office, it is working. Now, I need to take a switch in my office network (switch A) and add a new switch (switch B) for connect a near office. I have the same converter modulo in   both extreme (finisar trj8519p1bnl-mc), I configured the switch B with Ethernet wire (from 10.0.0.1) and I put an IP within to office range IP (the same that others switch).
    But when I connect the fiber in both switch port, the ports led are off. When I access to web interface from switch A, I can see the fiber port in yellow.
    Somebody can help me?
    Thanks!

    Disclaimer
    The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
    Liability Disclaimer
    In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
    Posting
    Unsure if this is your issue, but many Cisco devices, by default, won't run non-Cisco optics.  If not already doing so, you might try adding "service unsupported-transceiver" to your configuration.

  • Connecting 2 switches with Fiber

    Hi,
    I have a basic question regarding two 3750G switches I would like to connect using fiber.
    I have the 2 Twingig modules converter available for each switch.
    I need to know my requirement to connect these two switch by their uplink.
    I have already on my list:
    1 SFP module (GLC-SX-MM) the question is how many SFP modules will I need to connect these 2 switches as each switch has 2 Twingig port (hence 4 SFP ports available). since each Twing Gig port has 2 SFP module.should I use 1 Twin Gig module and ordre 2 SFP modules (GLC-SX-MM) for each switch (hence 4 GLC-SX-MM )for the connection to work ?
    Thanks for your guidance and related documentation you'll be giving.

    According to the following Cisco document, the Twingig converter module can be used with up to 2 SFPs; which would seem to indicate the use of 1 SFP in a Twingig converter module is supported.
    <http://www.cisco.com/en/US/docs/switches/lan/catalyst3750e_3560e/hardware/install/notes/1757202.html>
    You could install 2 SFPs per switch and run EtherChannel to gain additional uplink bandwidth.

  • Can I set port forwarding to replace my D-Link switch?

    I want to replace the D-link switch with Airport express, but I am wondering if I can set port forwarding on the Airport express? If yes, how many entries can I set?

    Is the AX connected via Ethernet to the internet AND is the AX configured to "share as single IP address"? If not, all ports are already forwarded directly through the AX and the port mapping option is not available.
    From Page 54 of Apple's "Designing AirPort Network" (direct PDF download link).

  • Connecting two Nexus switches with link

    Hi,
    I would like to connect two nexus switches with a link. Like one c5020 and one c5548p. How do i need to configure the ports at both the switches which will be joined with a fiber cable.
    For MDS switches such links becomes E-port and fabric is merged. Not sure what happenes at the Nexus swictches. Any input will be appreciated.
    Thanks,

    Do you have fc modules in each nexus? If so, they act much like the MDS 9148. All ports should be default auto speed and auto switchport mode. Insert fc-sfp's and a regular multimode fc cable between them. Default mode is fc switch.
    If that doesn't work, configure the mode on each port as E.
    Once done, the fc switch portion of each nexus will merge.
    Dave

  • Two switches connected with fiber in mode trunk - Problem

    Hi to all.
    Iam new in the forum, and my english is bad.
    I want to post a problem. I have two switches connected with fiber in mode trunk, in the switch C3550 i have this configuration:
    interface FastEthernet0/1
    description Enlace LAB Medicion
    switchport trunk encapsulation dot1q
    switchport mode trunk
    no ip address
    duplex full
    spanning-tree portfast
    In the switch C2960 this configuration, on interfaces Fa0/48, Giga0/1:
    interface FastEthernet0/48
    switchport trunk allowed vlan 1,20,229
    switchport mode trunk
    spanning-tree portfast
    interface GigabitEthernet0/1
    switchport trunk allowed vlan 1,20,229
    switchport mode trunk
    media-type sfp
    duplex full
    spanning-tree portfast
    The problem:
    The ip phones with Voice vlan (vlan 20), not find the DHCP server located in the data vlan (vlan 229)
    However, using the command:
    #switchport trunk native vlan 229
    The result is the voice vlan works, but the data vlan not and viceversa depending if the native vlan 229 is present.
    I will appreciate any suggestion.

    leolaohoo.
    The configuration on ports switch C2960, have the mode access with voice vlan 20:
    interface FastEthernet0/1
    switchport access vlan 229
    switchport mode access
    switchport voice vlan 20
    spanning-tree portfast
    interface FastEthernet0/2
    switchport access vlan 229
    switchport mode access
    switchport voice vlan 20
    spanning-tree portfast
    I will remove from trunk links:
    spanning-tree portfast
    Thanks alot.

  • Linking C2960s switches through Fiber optic patch panel.

    Hi, I have C2960s switches. I have to interconnect the switches through Fiber optic patch panel. Let me know which is the type of the connector used in the SFP ports.

    There are a types of connectors that you need to consider:
    1. Switch to Fiber Patch Panel
    2. Fiber patch panel to Fiber patch panel
    However, typically SFPs have LC type connection. With regards to Fiber Patch panel, typically (in my experience) SC type connection is used.
    I have attached screenshots of the connectors as well :)
    Don't forget to rate or mark as correct! :)

  • Which sfp module add in Sg300-10 for connecting with 4503 switch over fiber?

    Hello guys...
    i need help in network design...
    i have 2 cisco 4503 core switches with 48 port sfp that will use to connect at branches SG300-10 with 2 fiber that is single mode...
    which module should use in Sg300-10 that will compatable with 4503 fiber module?
    Please tell me if I will use the GLC-LH-SMD for  WS-C4500 with fiber optic card WS-X4448-GB-SFP what type of SFP do we have to use for the small business switch SG300-10?
    We could go for MGBLX1?
    if i am ok please reply if not please provide the correct one solution for my design...!

    Hello guys...
    i need help in network design...
    i have 2 cisco 4503 core switches with 48 port sfp that will use to connect at branches SG300-10 with 2 fiber that is single mode...
    which module should use in Sg300-10 that will compatable with 4503 fiber module?
    Please tell me if I will use the GLC-LH-SMD for  WS-C4500 with fiber optic card WS-X4448-GB-SFP what type of SFP do we have to use for the small business switch SG300-10?
    We could go for MGBLX1?
    if i am ok please reply if not please provide the correct one solution for my design...!

  • Internet provider switching to fiber optic. Will WRT54G router still work???

    I've recently learned that my internet provider is switching me to fiber optic. I've tried looking up the fiber optic thing on the internet but my knowledge about it is so limited that I'm not sure what to look for.
    Here is a link to a page on my internet providers website that has a tiny bit about it. It's called FiberConnect.
    http://www.rtc1.com/internet-rochester.htm
    Will my WRT54G router work with fiber optic?

    Yes it should work, just make sure you'd be able to connect to the internet when you connect your computer straight to the modem, then, install the router

  • Replace 3750x switches with equivalent fibre models

    We are currently using cisco 3750x's as our edge switches in our network (mix of 24 and 48 port switches).
    The office is being reconfigured and existing cabling is going to be replaced with fiber.
    What Cisco switch would be suitable (similar to 3750x) for gigabit fiber connectivity to desks?
    Thanks

    Disclaimer
    The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
    Liability Disclaimer
    In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
    Posting
    Most like your existing 3750X's would be, as noted by Leo, the 3750X-24S.  You can also, of course, stack them with your existing 3750X units.
    Regarding whether, as Leo suggests, they are "a sure waste of money", well I guess much would also depend on your cabling plant.  If your existing edge 3750X are in closets, and there's just a couple per closet, and you're just replacing floor copper, they probably are the most cost effective option.
    Unfortunately, they are getting dated, and I see Cisco has recently revised the product page to suggest considering the 3850 (or 3650) series, although those don't have an all fiber model.

  • Problems connecting two stacks with fiber

    I am having problems getting the 2 stacks to see each other with fiber. just your basic stacks, nothing fancy. Is there a line in the config that needs to be added? Fiber LED's are not lit.

    Hi!
    As you said the fiber LEDs are not lit, that means the ports are not 'up' so the stacking has not been done.
    Log into your switches and then run the command 'Show int interface name' to know the status of the fiber ports.
    Also check the connectivity of the stacking cables with the ports in the switch. Maybe you can take them out and then connect them again.
    HTH, please rate the post if it does.

  • Half Duplex/100M problem on 2960 switch with GLC-GE-100FX

    We have a 2960-24TC switch with GLC-GE-100FX SFP interface converter. We connected the switch to another switch through fiber, one end was GLC-GE-100FX and the other end was a 100/FULL ATI media converter. Both switches could talk to each other. The problem was the GLC-GE-100FX interface running at 100M/half duplex status and we couldn't change the port configuration. Is there a way to fix this problem? Your help would be much appreciated.

    Using show interface command. It shows half duplex. It's a new design on Cisco 2960-24TC switches, the Giga uplink ports are dual purposed. When I plugged GLC-GE-100FX SFP interface converter and connected it to a media converter, it showed half duplex. There's no way I could change the speed and duplex under that configuration.

  • Peer-Switch with vPC and non-vPC Vlan Port-Channels

    Hi,                 
    in a design guide i have noticed that it is best practice to split vPC and non-vPC vlans on different inter-switch port-channels. Now, if i want to use the Peer-Switch function, but the port-channel interface of the non-vPC-vlan channel moves into blocking state. The option spanning-tree pseudo-information has no influence. Is peer-switch possible in my kind of topology?
    Greeting,
    Stephan

    I believe absolutly possible. specifically coz peer-switch and spt pseudo-info are specific and local to cisco fabric services running as part of  vpc technology. Personally me has lab with vpc-domain compounded of 2 N5Ks. They are peer-switches with spt-pseudoinfo and they have MST running on non VPC links independantly from vpc.

  • New ESW-540 switch with cold start problems

    Hi
    A customer of mine is having serious problems with several ESW-500 switches.
    He started a discussion under Netpro, but haven't received any answers. This might be the right group?
    He wrote:
    I have two new esw-540 switches (one 48 port  and one 8 port),
    which are making unauthorized cold starts and  that gives me a lot problems.
    (now it is about three switches)
    I added:
    Hi
    My customer needs help with his problem.
    Here is some more information:
    There are three switches with the samHi
    A customer of mine is having serious problems with several ESW-500e problem now, all with the same errormessages from his log
    Ciscosw2  ESW-540-48   SN: DNI1452E71E SW Ver. 1.19 Boot Ver.1.0.0.04
    Ciscosw3  ESW-540-24   SN: DNI1433E507 SW Ver. 1.19 Boot Ver.1.0.0.04
    Ciscosw7  ESW-540-8     SN: CBT15230E9Z SW Ver. 1.1.19 Boot Ver. 1.0.0.07
    From ciscosw7:
    Nov 11 02:16:03 ciscosw7 %OS-F-MEMORY: OSMEMG_rn_free: Memory magic is invalid
    ***** FATAL ERROR *****
    Reporting Task: BNJR.
    Software Version: 2.1.19 (date  14-Jul-2010 time  17:12:34)
    0x184e9c
    0x182484
    0x564110
    0x392684
    0x395998
    0x568630
    0x2df10c
    0x2df654
    0x2e1138
    Nov 11 02:17:14 ciscosw7 %INIT-I-Startup: Cold Startup
    And he sent me a new errormessage today:
    Nov 13 01:38:14 ciscosw5
      %SYSLOG-F-OSFATAL:
      FATAL ERROR: BNJR: ABORT DATA exception
    ***** FATAL ERROR *****
    SW Version  : 2.1.19
    Version Date:  14-Jul-2010
    Version Time:  13:58:28
    Instruction 0x2EFB04
    Exception vector       0x10#
    Program state register
    0x20000013
    0x002ef7ac
    0x002f0390
    0x002f08d8
    0x002f23bc
    0x00134684
    Nov 13 01:39:27 ciscosw5 %INIT-I-Startup: Cold Startup 
    Need urgent advise...
    Thank you!

    Hello!
    My name is Robert and I am network engineer for the Cisco SBSC. This is the correct place for the ESW500 series.
    From the error messages you are seeing, I would recommend to disable the Bonjour service to see if that helps with the reboots. I am currently looking into the error messages you are getting to see if there is a solution. I would recommend giving us a call as well for immediate assistance on the error messages. Below is a link for our support center numbers.
    http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html

  • HT5624 my iphone is connected to a old account that i have used in a while i have a new icloud i tried reseting my phone but now i can get in becuase it linked in with my old account how can i fix this so i can log in with my new account?

    my iphone is connected to a old account that i have used in a while i have a new icloud i tried reseting my phone but now i can get in becuase it linked in with my old account how can i fix this so i can log in with my new account i reset my phone but i did it before on my new phone but this old is link to a account that i set up when i was so much younger can you advise what to do?
    Thanks

    Go into Settings App and turn OFF Find My iPhone. It will ask for your old password, but in the future you can use your new Apple ID account. If you need to reset the old password try this: https://iforgot.apple.com/password/verify/appleid?language=US-EN&returnURL=https ://appleid.apple.com/cgi-bin/WebObjects/MyAppleId.woa&app_id=93&app_type=ext

Maybe you are looking for