LInksys E1200 Wireless router is not responding after a while

Hi there, I have E1200 wireless router and it was working nicely for the whole last year with 2 mac laptops hooked up on it. About 2 months ago there were 1 mac,1 win laptop and a network printer. And again, it was working just fine at the beginning. I'm not sure when exactly it happened first, but now after working couple of hours internet gets off and router stops responding. If I try to reconnect to it from my laptop I just see an error message saying something about "Connection timeout". Also I don't know does it have something to do with the network printer, btw it's connected to the router via ethernet cable not wireless. Anyway, the only solution I've found so far is power off the router for a couple of secs and power it on again, which is obviously not a solution at all, it's annoying and not practical. The time it works fine before it dies is also not fixed, it might be even 10 hrs of working and sometimes only 1-2 hrs. My other suspicion is firmware. I upgraded it almost at the same time when new laptop and printer showed up. Maybe I have to downgrade it, but I couldn't find older version of it. It was HW v. 1, SW v.1.0.00, and now it's HW v.1, SW v.1.0.03. I'd highly appreciate if someone could help me out or at least show me direction where to dig in. Thanks.

It seems that router is intermittent. I suggest you observe your internet connection without the router which means connecting the computer to the modem (if you can) to isolate if your modem's internet connectivity is okay or stable. Upgrading the firmware to the latest is actually okay. Try to reset your router back to factory defaults by pressing its reset button found at the bottom for 10 seconds. When you do reset by the way, it will delete all the current settings that you have especially for the wireless. But you can take note of them before you reset the router. After the reset, you have to get the internet up and running again. You may refer to  the links below on how to get it up and running again for wired and wireless internet.
Setting up a Linksys router for DSL Internet connection
Setting up a Linksys router with Cable Internet service
Different ways in setting up your Linksys wireless router

Similar Messages

  • My Linksys E1200 wireless router stopped working

    Hi, my Linksys E1200 wireless router stopped working. When my checked my network it said "Limited Connection." However, when I connect my ethernet cable directly to the modem my internet works fine.
    Can someone help me with this?

    @JeffNewYork
    Are you getting that error hardwired to the router? Or wireless? Since the internet is working directly to your modem, you may need to reset and reconfigure the router depending on the settings from your Internet Service Provider (ISP).
    Setting up a Linksys router with Cable Internet service
    Setting up a Linksys router with DSL Internet service
    Setting up a router with a Static IP account
    Good luck! 

  • 8.1SP2 Webserver does not respond after a while

    Hello,
         I've had this happen several times. Nothing in the logs shows anything
    strange. It logs the HTTP requests coming in, but does not return a
    response.
         The process is still running, and the applications can connect to the
    port, but they hang on waiting for a response.
    My setup:
    Redhat Linux 9 w/ Weblogic Server 8.1 SP2
    I'm trying to connect to the /console app, but have also tried to access
    the / directory to make sure it wasn't just the console that was hung.
    Thanks

    Mylenium
    Thank you for the suggestions.
    I checked the WIndows log files. It reported the following error:
    The program Acrobat.exe version 10.1.1.33 stopped interacting with Windows and was closed. To see if more information about the problem is available, check the problem history in the Action Center control panel.
    Process ID: 4770
    Start Time: 01d0079a09bba381
    Termination Time: 13
    Application Path: C:\Program Files (x86)\Adobe\Acrobat 10.0\Acrobat\Acrobat.exe
    Report Id: 4f145db6-7391-11e4-8fc1-005056c00001
    I ran for the memory diagnostics as it showed the error with video card error. My NVDIA graphics card is not working properly. Do you think that could be a problem?I am running on Windows 7 64 bit computer. It also complains about the incompatibility with 64 bits.
    Thank you.

  • I JUST BOUGHT AND INSTALLED A LINKSYS E1200 WIRELESS N ROUTER AT HOME. MY IPHONE CONNECTS WITH A STRONG SIGNAL BUT WHEN I TRY TO USE THE INTERNET IT JUST LOADS FOREVER. HOW CAN I FIX THIS?????!!!!

    I JUST BOUGHT AND INSTALLED A LINKSYS E1200 WIRELESS N ROUTER AT HOME. MY IPHONE CONNECTS WITH A STRONG SIGNAL BUT WHEN I TRY TO USE THE INTERNET IT JUST LOADS FOREVER. HOW CAN I FIX THIS?????!!!!

    RESET YOUR ROUTER
    No. Reset your router.

  • I have a Linksys WRV200 wireless router and the wireless signal is not working properly so I cannot connect to the internet wirelessly. the wireless light has a fast green blinking light. how can I fix the router?

    I have a Linksys WRV200 wireless router and the wireless signal is not working properly so I am unable to connect to the internet wirelessly.  The wireless light is blinking green very quickly and I connect and disconnect from the network constantly.  How do I get the router to work properly

    Hello James,
    The flashing WLAN light means activity (data getting transferred). Try disconnecting all your devices and check whether the light is still flashing or disconnect the router from internet and do the check.
    Do you have your SSID as linksys or the default one? If your neighbor has the same SSID, then traffic could result from your neighbor's one. Try changing your SSID and password. Make your security WPA/WPA2.
    Hope this helps,
    Thanks
    Vijay

  • How to connect a E1200 wireless router to a machine tool network for wireless communications

    Hello all, I am new to the forum, hope someone can help me out. I am wanting to connect my E1200 wireless router to a machine tool in our factory that has programmable controllers and is connected to the machine components via ethernet connections. This is so we can troubleshoot the machine without having a wired laptop. We have several ethernet switches on the machine and a range of IP addresses say from 192.16.1.1 through 192.16.1.150, and 192.16.17.1 through 192.16.17.150, all of the addresses are not used but random addresses in the range. I would like to be able to connect my E1200 to either one of the networks without having to make a change in the router setup. I can make it work on either network but when I switch my cable to the other network it has to be reconfigured. I am currently connecting my data cable to a ethernet port on the router and changing my router address from 192.168.1.1 to 192.16.1.1 and selecting a range of 150 so it will assign numbers as needed. This works great until I change to the other network and I have to change my router address to 192.16.17.1, I know this can be done on some routers because the technicians from the machine builder use them when working on the machines. thanks

    On the basic setup tab make the changes shown below:
    This basically make the router disappear off the existing networks and turns it into a wireless AP.
    Then when you set your laptop's wireless adapter to whatever IP network you want to connect to.
    If you need to connect to your router again change the laptop's adapter IP to something like 192.168.200.2
    Keep in mind nothing ever gets plugged into the Internet Port on the router.
    What I do with these manufacturing machine's is put them on the company network with static IP's. Then so operators can transfer programs and view drawings I place ELO touchscreens at each location. For the Laser cutter operators that do nesting they have a desktop workstation for the CAD software and put the nests on a network share or direct to the laser cutters.
    Please remember to Kudo those that help you.
    Linksys
    Communities Technical Support

  • Linksys WRT110 Wireless Router

    I need to setup my Linksys WRT110 wireless router for  wireless use as well as a router between my cable modem and my desktop PC. So far, I cannot find any documentation on how this is done or if it is possible at all. When I called Linksys support they told me it can be done and provided me with a link to the instructions, however, they did not work. Does anyone know if this is possible? I need to setup in order to work from home and I cannot use a wireless connection to my cable modem but I need a router between my desktop PC and my cable modem. Oh, by the way, I have a new HP desktop which is running Windows 7.  I would appreciate any help someone can lend me.  Thank you. SHH

    From what i read on your post looks like your trying to use your wrt110 as a wireless access point and you want to still use your router near your modem.
    To do this what you have to do is disable your wrt110 as a dhcp server since your other router near your is acting as the dhcp server.
    So what you do is hook a cable to your wrt110 in port 1. type in 192.168.1.1 in the address bar of your internet explorer.For now this 192.168.1.1 number will get you into the wrt110 until you change it to 192.168.1.5  under setup you will see 2 areas. Under the ip address type in 192.168.1.5 so this make your wrt110 have this ip address.
    Below that you will see DHCP server setting disable this. So your wrt110 will not act as the dhcp server it will act as a wireless access point.
    Now if you type 192.168.1.1 in your web brower that will open the configuration screen of the router next to your modem. Which that dchp server setting will be enabled.
    So basically from your modem your first router will route the signal from the modem thru the router to the computers hooked to it. then say you run a cable from that router to the wrt110.So basically your just uplinking to the wrt110. only thing is your wrt110 will have to act as a access point instead of a router.
    Your main router configuration screen to get into it. you would type 192.168.1.1 in your brower after you setup your wrt110 an disable the dhcp server and set the ip to 192.168.1.5 when you type this number  the 105 number in your browser it will go into the web config screen of the wrt110
    So to access the web config screens of both routers they will have different numbers.
    1st router by your modem will be 192.168.1.1
    2nd wirless one will be 192.168.1.5 which you changed when you when in and disable it as a dhcp server since your 1st router by your modem acts as the dhcp server.
    Hopefully this will help. I know it does get a little confusing been there and done that more then once.  If not call linksys on the phone tell them what products you have and how you want it to work they will walk you thru it.
    My setup in my home from my modem it connects to a 4 port router, then from there to a 24 port switch then uplinks with a Power over Ethernet adapter which sends power thru this little adapter over the brown pair in the cable so you dont need a electrical outlet where you put your wireless access point/router. Then from my switch it uplinks with that POE to a Wrt110 upstairs in my home. I know what a pain this can be i've call them more then once to get mine setup and working.
    GOOD LUCK HOPE THIS HELPS

  • How do I connect my HP Laserjet 1102w directly to a Linksys AE3500 wireless router with USB option?

    I am trying to connect an HP Laserjet 1102w directly to an HP desktop model a172n with Windows Vista Home Premium OS (32 bit) through a new Linksys AE3500 dual band wireless router which has a USB port for a direct connection. The desktop can see the wireless router but not the printer.
    Is there a work around, a printer installer update, or some other solution that enables me to connect the desktop to the printer via the USB connection on the wireless router? I need to have one wireless laptop and one non-wireless desk computer able to use the one printer.
    Thanks for any assistance!
    Murleen Ray

    hi there,
    It seems as though this situation will require the Cisco connect software to function properly. Check out this article from the cisco knowledge base. It has the step by step setup specific to your case. Let us know if this helps or if you have already been through these steps.
    Best of Luck!
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • Hi,   I just bought a linksys WRT54G Wireless Router. My...

    Hi,
    I just bought a linksys WRT54G Wireless Router. My laptop was able to detect it wirelessly untill I changing the "Router Name" in the setup page(http://192.168.1.1)
    While saving the settings, the wireless network suddently disconnected. From that point onwards, I was not able to detect the wireless network with any computer at all.
    I tried unplugging it, resetting it, and even restory factory settings by holding the reset button for aprox 30 secs.
    What is wrong?
    Thanks in Advanced

    Recheck the wireless setting (SSID, encryption, DHCP, etc) on router management page again. Also make sure your computer's wireless adapter setting matches the one you set on router.
    picoHat
    Home Network, Wireless Network and Computer Networking Made Easy

  • Trying to setup my Linksys WRT54G Wireless Router but having trouble.

    Right, i will keep this nice and simple. I have had broadband internet for the past 10 days and yesterday i got myself a Linksys WRT54G Wireless router so both myself and my partner can connect our Macbook Pros up to the wireless internet.
    But the problem is we cannot seem to connect onto the wireless network. It shows up when searching for internet connecting even when its is open without a password or with a password it does not want to connect?!?!
    I can plug my laptop directly (as i am doing now) into the broadband modem and it works so i have no idea what is wrong? This afternoon we tried using a Windows Laptop and had the same problem. The wireless network shows up but when you enter the password that was entered on the 192.168.1.1 website it does not reconise it?!?!
    If you can reply speaking English and not too much computer language that would be fantastic.
    Many thanks

    Hi candn14 and welcome to the forums!
    Since internet connection is working fine on the laptop computer when plugged directly into the modem, you just need to configure your router settings.
    Are you using a DSL or Cable connection? Please see the links below on how to configure your router with your internet provider (ISP).
    Setting-Up a Router with Cable Internet Service
     Setting-Up a Router with DSL Internet Service
    Once you are finished doing so and your laptop is able to connect to the internet when connected to the modem > router > laptop, then you are now ready to configure the wireless settings of the router for you to be able to connect wirelessly.
    Here are the steps:
    Setting-Up the Wireless Settings on a Router
    And please secure your network w/ a password.
    Setting-Up Wireless Security on a Linksys Router
    Please feel free to ask any questions again if you encounter any problems. Hope this helps.

  • When I try to open firefox it says that it is not responding, after I disabled the adobe flash plug-in it worked, how do I get it to work with flash

    Since I updated my adobe flash player firefox keeps saying that it is not responding after I open it and it loads my home page, I disabled add-ons and went throught the process of figuring out which one it was and it was adobe flash, but without flash I cant access a lot of different sites, how can I fix this. I have tried uninstalling and reinstalling both firefox and adobe flash, but neither works!

    See "Hang at exit":
    * http://kb.mozillazine.org/Firefox_hangs
    * [[Firefox hangs]]

  • HT3917 My apple wireless keyboard is not working after new batteries installed

    My apple wireless keyboard is not working after new batteries installed.

    Do you get a steady green light to say there is a connection.    If not, are the batteries the right way round.   Do you have a monitor to tell the batteries strength. Is there a reading.   Are the batteries good quality ones, Duracell, Energiser or Apple rechargeables.

  • App Store not responding after upgrade to OS X Mavericks and installing free Keynote, Pages and Numbers app

    My App Store is not responding after upgrading to Mavericks and installing free Keynote, Pages and Numbers Apps.
    Also I tried to reboot and restart and nothing happens still unresponsive.
    Tried to click as many times as I can the App Store and it won't open.
    Please Help.

    Dongski
    I had the same problem and solved it myself.
    Please see discussion  https://discussions.apple.com/message/23556072#23556072
    Hope it helps

  • My Adobe acrobat X Pro does not respond after a minute I open up a pdf file

    I recently have installed Adobe Master Suite CS6 Collection. My Adobe acrobat X Pro does not respond after a minute I open up a pdf file. This happens every time when open a new pdf file. My operating system is Windows 7 pro ( Lenovo-64 bits). Any suggestions would be appreciated !!

    Mylenium
    Thank you for the suggestions.
    I checked the WIndows log files. It reported the following error:
    The program Acrobat.exe version 10.1.1.33 stopped interacting with Windows and was closed. To see if more information about the problem is available, check the problem history in the Action Center control panel.
    Process ID: 4770
    Start Time: 01d0079a09bba381
    Termination Time: 13
    Application Path: C:\Program Files (x86)\Adobe\Acrobat 10.0\Acrobat\Acrobat.exe
    Report Id: 4f145db6-7391-11e4-8fc1-005056c00001
    I ran for the memory diagnostics as it showed the error with video card error. My NVDIA graphics card is not working properly. Do you think that could be a problem?I am running on Windows 7 64 bit computer. It also complains about the incompatibility with 64 bits.
    Thank you.

  • Premiere Pro CS6 not responding after adding anything to timeline

    I had been using Premiere CS6 successfully for a while, but starting a few months ago, it started not responding after I did anything.  I can add a title and a transition succesfully to the timeline and it plays fine, but as soon as I add a picture or video clip, it immediately stops responding.  It's frustrating because the program used to work fine before.
    The only thing I can think of that might have affected it was when I upgraded to Mavericks, but I haven't read anything about any serious problems with Premiere running on Mavericks.  I have a late 2008 MacBook Pro.
    Thanks in advance for the help.

    Go to http://forums.adobe.com/community/premiere and, in the area just under Ask a Question, type in
    mavericks
    You may now read previous discussions on this subject... be sure to click the See More Results at the bottom of the initial, short list if the initial list does not answer your question
    I am Windows so did not bookmark the messages, but I have seen SOME message threads with SOME solutions for SOME mavericks problems

Maybe you are looking for

  • How to apply Filters to Camera in ViewFinder.

    Hi,I have work  Grayscale video effect,but don't find any other filter(effect) like  Sepia,Solarize etcvideo effect.If anyone know how to apply these effect  then please provide sample link or sample code for these.

  • Using more than one phone number on single iPhone for iMessage?

    Is it possible to intentionally have more than one phone number listed under Settings > Messages > Send & Receive?  I know I've heard of 'glitches' where more than one phone number is shown accidentally and how that is solved (signing out of iMessage

  • How do I set up automatic duplex printing for my HP Laserjet Pro400 M401n series?

    How do I set up automatic duplex printing for my HP Laserjet Pro400 M401n series from my PC  using windows 8?

  • Storage Unit Date

    Dear Experts Please advice which exit / badi / enhancement can be used to derive the same / orginal storage unit date in case when we transfer stocks from one storage location to other. when the stocks are transfered from one Sloc - WM location to ot

  • Batch create error /IWCOR/CX_DS_EP_PROPERTY_ERROR/

    Hi All, I am trying to create multiple records using $BATCH, but I am getting below error(I could able to perform READ& QUERY well but not successed with Create/update) HTTP/1.1 500 Internal Server Error Content-Type: application/xml Content-Length: