Linksys E2000 firmware bug for v1.0.02 build 4Jul. 9, 2010

I run a website where I help people setup port forwarding in their router.
So I do know how everything works.
I own the e2000 and port forwarding has always worked. I updated the firmware and port forwarding works on the single port forwarding page and on dmz. but the port range forwarding page is no longer working. no rule added to that page will work. but the same rules will work on the single port page.
I want to report this bug in hopes it will get fixed.
Till then does anyone have a download link to an older firmware?
Thanks
Shane

Glad that it worked!
Please click "Accept as Solution" on the post that helped you solve the problem and Give Kudos.
Cheers!
OnnagokorO

Similar Messages

Linksys WRVS4400N Firmware Bug!

i have problem whit my Firmware. I can not open all order of FTPs and i can`t Upload on a FTP and this of all Computers. Test: Cute FTP FileZilla Client SmartFTP Whats this for a bug? Its WDS coiming soon on WRVS4400N?

since it seams like you are having an issue with your firmware , you can perform a factory reset by holding in the button in on back of the router for 30 seconds, wait about 2 minutes and try to upgrade to the latest firmware.
Below is a link to help you with the firmware upgrade.
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=4030&p_created=11601...
Good Luck,
Ttech

Ios 5 possible firmware bug for iPhone 4; Voice command/text-to-speech doesn't work properly.

I upgraded an AT&T and Verizon iPhone 4 to the ios 5 firmware, and I am having the same exact issues for both phones. When using the voice command a few times, the audio voice does not come through the "speaker" (referring to the speaker located at the bottom of the phone). Instead, the audio voice goes through the receiver which is on the front face of the phone, on the right of the camera.
For example, say you want to use the voice command to dial a phone number. You would enable voice command by depressing and holding down the "Home" button and give the command "dial...1-800-452-3456", the phone would then repeat the phone number back to you through the "speaker". However, when I did this a few times, the voice instantly goes to the receiver instead. I found no way to fix this problem. I tried the following and none of these solutions worked:
Turned the phone off and back on again
Hard reset (held down the Home and Lock button for 10 seconds)
Restored the phone, and set the phone up as a "new iPhone" instead of restoring from back up
After trying to restore both iPhones and still have the same issue, I made an appointment to visit Apple. I took the Verizon iPhone 4 to Apple, and the employees handed over a refurbished iphone in hopes to solve this issue. However, this refurbished phone still had the same exact issue.

Of course I checked my apps library and found nothing. However I'm looking at the status while sync is processing, I'm 100% sure that app is not synced to my iTunes library
Yep, I can always manually "transfer purchases" to my iTunes library. But this is not the point. On my old iPhone 4 and new iPad (3rd gen), it will sync all newly installed apps from my iOS devices to my iTunes library, no need to click "Transfer Purchases" again.

Linksys E2000 router is incompatible with Linux?

Hi All, I have Cisco/Linksys E2000 router setup for home wireless network. I had been setup while ago and well working since then. Now the challenge: I need to know or to change the wireless guest network password. Linux support says it can be done ONLY using a local application, not the web interface. And only from Windows computer. In my situation, I have Linuxes, blackberry, players and other network equipment but no Microsoft software. I did not know that router doesn't work with Linux when I bought it. Had anybody resolved similar issue? Thanks Yu

Sorry the software is only supported on Windows or MAC. You will need this to administer the Guest network.

E55 Thread for Firmware Bugs

I noticed that there isn't yet a thread in order to report E55 firmware bugs, so I started this
Here the firmware bugs I've found:
- Hidden WLAN: when you search for wireless access points (for example from the main screen) the phone see always one "hidden wlan", that is not there!
- Default phone numbers: when you have more phone numbers for a contact, you can choose one of these as default for messaging or dialing, but even if you do that, E55 keep asking you what number to use every time you make a sms
- Organizer major bug: sometimes (80% of times!) when you edit a memo in Organizer, or when you move it (by changing the start date), you will see that also the end date has changed (adding 1 or more days), even if you didn't touch it! And even if the start and the end date originally matched! So if you had a memo covering one day, now it covers more days, and the end date can't be changed again (you set the correct date, save, and none happens). This make the memos totally unusable!
- Organizer minor bug: when you open Organizer, and then open a memo, you have to select the information that you want to modify (text, date, synch) and click one more time to edit the memo. But: if you select the "date" or the "synch" row, instead of the "text" row, and then click "modify", the memo is open alway with the cursor on the "text" row. So, the capability of selecting others rows, is pretty useless.
I hope some Nokia guy will notice this thread so there informations can be useful for a future firmware release, also because I'm getting crazy with the memos issue!!
Roberto
Moderator note: word 'official' removed from title, as this may mislead users to believe that the information presented comes from or is in some way endorsed by Nokia.
Message Edited by michaels on 05-Oct-2009 10:06 AM
Message Edited by michaels on 05-Oct-2009 03:31 PM
Roberto Dapino
http://www.stormvision.it/blog

hi olandesevolante
about ur first and second issues u face they r not realy bugs, why?
for the first one: i faced that with my E51 in a place i visited before, that hidden WLAN maybe a conflict from another type of waves other than that of wlan using same frequency
and about the second issue: default phone numbers is a feature that only set for making calls but when u make an sms the phone will ask u to choose between numbers present unders the same contact name even if u set a default number, so it is not a bug but that is the normal firmware properties
for the rest of issues , they sound like real bugs
i hope i helped a little and i wish those bugs will be removed in the next firmware
Message Edited by michaels on 05-Oct-2009 03:31 PM
Phones I bought from 1st till now:
3210 / 3310 / 3410 / 6310 / 6600 / 6020 / N72 / E51 / X2-00 / 5310 xpress Music / E90 Communicator
If you like my post or it helped you, Give me Kodo

Huawei e870 Firmware Upgrade for LinkSys WRT54G3G

All
Is there any information available about if LinkSys will be releasing a firmware upgrade for the WRT54G3G to allow the use of the Huawei e870? If so, is there an estimated delivery date?
Many thanks!
cjm

All
Is there any information available about if LinkSys will be releasing a firmware upgrade for the WRT54G3G to allow the use of the Huawei e870? If so, is there an estimated delivery date?
Many thanks!
cjm

Linksys E2000 Fail

So the other day I am having problems with my router , I stop by Best Buy and pick up a Linksys E2000 . Almost the top of the line router, out of the box it will not talk to the modem. Ok I have Charter come and replace the modem, plug back in the brand NEW router still will not get a IP from the modem. I update the firmware in the router and ask Linksys support for help and still it will not connect to the internet. This is the 2nd Linksys product I have got in the last 2 years that have failed or failed to get fixed by Linksys !

most cable providers don't have mac clone registration security on their lines but on some that do, you need to have that done no matter what the brand of your router is. Are you doing the MAC Address clone procedure on the primary computer? Are you doing it while wired on the router? The wired adapters mac address is the one you have to put into the router mac address clone subtab so you'd get connected. I would suggest you take a look at the mac address you are getting while directly connected to the modem first then write it down, go to the router setup page and see if the same numbers and letters appear, if not then change it to that and turn off everything then turn them back on. That should get you online.
"Sometimes your knight in shining armor is just a retard in tin foil.."-ARCHANGEL_06

Firmware upgrade for WRT54G v7

is there no firmware upgrade for WRT54G v7? i didn't even find version7 as listed in linksys page for routers....

Click on Download and save the file on your Desktop..
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...In the address bar type - 192.168.1.1...Leave the Username blank & in Password use dmin in lower case...Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab-Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...Wait for few seconds until it shows that "Upgrade is successful" After the firmware
upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Where do I get an SMC Firmware Update for my 21.5 inch Late 2009 iMac?

Hello Apple Support Communities,
I have a 21.5 inch, Late 2009 Intel iMac. Currently it is running OSX Lion. It is also running Bootcamp with Windows 7 Professional Installed. Recently the Hard drive crashed on me and I ordered a new generic Hitachi from an Apple Reseller. I took all the precautions and asked all the questions, but when I finished the hard drive replacement, the fans within the iMac started running on High. The other people in my office Hate this. I did some research and found that there is a firmware update for the SMC that I should be installing. I looked on the webpage where apple directs you to find out if you need this update, but I can't find my exact specs on the page (here is the page for reference: http://support.apple.com/kb/HT1237) I can only find an update for the 27 inch model. I tried running that one and the system tells me "This software is not supported on your system."
Here are the specs that the page requested me to find:
Model Identifier:          iMac10,1
Boot ROM Version:          IM101.00CC.B00
SMC Version (system):          1.52f9
Someone please help, this has been bugging me for a while.

I took all the precautions and asked all the questions,
Then I trust you saw this before you did the replacement. Apparently, it's not just a question of getting a drive from the same manufacturer to use with the proprietary cable.
http://blog.macsales.com/2751-proprietary-cable-can-put-the-brakes-on-upgrading- late-09-imacs
It's acting as if the temp sensor is not connected. I have it bookmarked amidst thousands of bookmarks but can't remember the name right now. There is some program out there that, in the absence of getting data from the internal sensor, will regulate the fan speed based on the SMART temp. If I think of it, I'll post back.
Here it is. It's meant for the 2011 iMac Apple drives, but I don't see why it wouldn't work in your situation.
http://www.hddfancontrol.com/
BTW, I think John Galt is thinking of the 2011 iMac drives, not the late 2009s, which are not quite as impossible.

Help setting up my Linksys E2000 to play a game

I just recently bought a Linksys E2000 router. Works great while searching the internet and such.. But I get huge lag spikes while playing Call of Duty Modern Warfare 2. I know its not my computer. When I take it to work and hook up to my jobs wireless connection I can play lag free. Also if I disconnect the router and hook up directly to my cable modem I can play lag free. SO I am fairly certain that the problem lies in my router settings.. Can any of you help me out? I don't have the slightest idea how to set up a router. I know the game says my Nat needs to be completely open while playing the game and that I should forward certain ports. I have no clue how to do either of that.. I will copy and paste some instructions from the forums for the game for you all to see. Thanks in advance for any ideas.
Brian
Required Ports for Modern Warfare 2
In addition to the required ports for Steam, Modern Warfare 2 requires the following ports for multiplayer:
UDP 1500 (outbound only, no forward needed)
UDP 3005 (outbound only, no forward needed)
UDP 3101 (outbound only, no forward needed)
UDP 28960 (inbound/outbound, must forward to act as a multi-player host, but no forward or inbound traffic needed to find and join games)
Steam Client
UDP 27000 to 27015 inclusive (Game client traffic)
UDP 27015 to 27030 inclusive (Typically Matchmaking and HLTV)
TCP 27014 to 27050 inclusive (Steam downloads)
Dedicated or Listen Servers
TCP 27015 (SRCDS Rcon port)
Solved!
Go to Solution.

You don't really have to set up a static IP for your computer. All you got to do is reserve that IP in DHCP reservation on your router. Get the MAC address of your computer, put that in the DHCP reservation located on the setup page under Basic Settings. Choose the IP you want, within the scope of DHCP. Make sure to save it. So everytime you connect to the router, it will assign that IP to your computer.

How to get a open NAT type with a linksys E2000 on PS#

I called customer service and they were completely clueless, told me I had to pay for the Tech support to fix it. I have a Linksys E2000 and I cannot get a open nat for my PS3, tried the DMZ, and XBox settings but that obviously didnt work. So anybody have any ideas before I return this $100 router???
Solved!
Go to Solution.

I've been having the same problems but on my Xbox. I'm going to try this:
On router:
1 - Status tab
   Get DNS 1 & 2
On Xbox:
2 - Static IP on Xbox
   IP: 192.168.1.xxx
   Mask: 255.255.255.0
   GW: 192.168.1.1
3 - DNS Addresses on Xbox
On router:
4 - Forward ports
   TCP 80
   UDP 88
   Both 53, 3074
5 - Security tab
   uncheck Block Anonymous Internet Requests
   disable uPnP?
6 - Reset devices
I'll let you know how it goes.

HP Laptop and Linksys E2000

I cannot get the HP laptop HP dv6915 connected to a Cisco Linksys E2000 router. I have updated drivers for the WiFi card but can't get connected via the wireless connection. Cisco is no help at all. Does anytone have the magic answer on how to make this connection?

Hi:
The only thing I can think of, is because the E2000 is a selectable dual band router, you should make sure it is set for the 2.4 GHz frequency. If it is set to the 5 GHz frequency, your wireless card won't pick it up. According to the specs on your notebook, it has a wireless G (2.4 GHz) card.
Paul

WHY DOESNT NOKIE POST MORE FIRMWARE UPDATES FOR OT...

I AM NEW TO THIS BOARD AND HAVE FOUND THAT NO MATTER WHAT I DO TO UPDATE MY NOKIA 6230i (FIRMWARE AND RADIO SOFTWARE)I MEET A BRICK WALL.
IT SEEMS NOKIA ARENT INTERESTED IN GIVING YOU SUPPORT ONCE YOURE PHONE IS ANY MORE THAN A YEAR OLD.
THIS TO ME IS VERY UNFAIR AS I HAVE SPENT A LOT OF CASH ON THIS PHONE TRYING TO UPDATE VISUAL RADIO USING THE DIRECTIONS PROVIDED WITH NO SUCCESS AS THESE DIRECTIONS DO NOT WORK AS I CANT FIND ANYWHERE TO DOWNLOAD THE THE NEW VISUAL RADIO WHILEST ON WAP.
THIS TO DATE HAS COST ME £75 TRYING TO FIND THE LINK.
ALSO I HAVE BEEN ASKING FOR THE FIRMWARE UPDATE FOR THE 6230i AS I SEE THIS AS BEING FAIR AS EVERY OTHER MOBILE THAT IS BEING POSTED CAN BE UPDATED OVER THE AIR AND THROUGH SOFTWARE UPDATE.
WHY CANT MINE AND MANY OTHERS.
EVEN IF NOKIA POSTED THE LAST RELEASED FOR EVERY MOBILE EVEN FOR THE OLD ONES I WOULD BE VERY GREATFUL .
MY NOKIA HAS A VERY OLD FIRMWARE V3.40 THIS NOKIA KNOWS IS FULL OF BUGS AND SHOULD BE HELD ACCOUNTABLE FOR POSTING THE FIXES UNTILL THERE ARE NO BUGS TO SORT WITHOUT EXCESS COST OR HAVING TO VISIT A RECOMMENDED REPAIR DEALER.
I WANT IT FREE JUST LIKE THE NEXT GUY SO NOKIA POST THE FIRMWARES AS SOON AS POSSIBLE AS I AM COMPLETELY FED UP WITH THIS FONE AND ITS BUGS.
YOURS SINCERELY
AN UNHAPPY CUSTOMER

First of all, please locate the Caps Lock key of your keyboard; all upper case text is hard to read, and traditionally considered as shouting. Of course, you may already know that, and intended to shout.
Anyway, most phones do not have the built-in support for do-it-yourself firmware updates.
For such phones your options are (if you think you need a firmware update):
- Take/send the phone to an authorized Nokia service/repair center, where the update can be done.
- Buy relativelt expensive flashing equipment and locate illegally distributed firmware files and try it on your own with that.
My advise is to go for the former rather than the latter option. The former should cost you anything (at least not for as long as the phone is under warranty & excluding what it takes for you to go there).
As to downloading "THE NEW VISUAL RADIO WHILEST ON WAP", I don't know what you mean by that. I don't know a 6230i, but either it comes with Visual Radio built-in or not. Any updates/fixes to it would come with a firmware update, but not over WAP.
Note also that you don't need the Visual Radio service to listen to FM radio channels, and most radion stations do not support the "Visual" bit at all (if they do, the support is indicated in the station directory in the radio app on the phone).

Firmware wishlist for the MuVo Sport C

I would like to start a thread to discuss the suggestions for firmware update for the MuVo Sport C00. FYI, I am running firmware version .0.0. Please post your comments or ideas to my suggestions, or reply with your own comments.
Before I begin, I'd like to say that I think the C00 is an awesome sports player, but it could definitely be improved. My Fiance has the Rio Cali 256, which is also a good sports player. Right now I think it's a toss up between the Cali and C00, but I think the C00 has the potential to outshine the Cali. (I like the Cali's separate volume controls, but I dislike how it falls out of the armband.)
Here are my suggestions in my order of importance:
[urgent] Fix the stopwatch so that the user can change tracks while the stopwatch is running. You should be able to press "Menu' and toggle between stopwatch and music modes while the stopwatch is running.</LI>
[urgent] Fix shuffle mode so that it truly shuffles playback from internal and external memory. Right now it appears to select songs from internal memory 90% of the time. Also, I don't think the player has ever selected anything over the 200th song on the player for shuffle playback at the root level.</LI>
Provide the ability to select a specific song for playback from the Menu. Right now, you can only select the folder for playback and then navigate to a specific song from there.</LI>
Reorder the Menu icons, and place "Folder", "Stopwatch", "Music" and "Play Mode" next to each other. This would allow for easier and faster navigation while running.</LI>
That's all I can think of now. Does anyone know how to submit these to Creative's dev team so they can consider them for a future firmware update?
Message Edited by sixseven on 05--2005 02:50 AM

Definitely, point one in the list is the most urgent one (making player functions accessible without having to stop the stopwatch). This ridiculous flaw leads to the situation that from day one after buying the device it rests unused in my drawer. I do not agree that there is no marketing for this device. Actually, I bought this thing for 20 Euro after I read in an ad that this was the ideal mp3 player for sports. Maybe for 00m runners this is right (you barely change a music track during the2 seconds). But for any distance above 000m it is just laughable.
I wish there would not have been marketing at the time when I searched for a sports-mp3 player. I wouldn't have fallen into the trap to buy this crap. And that Creative is not able to provide a firmware upgrade which corrects this bug for about .5 years now is enought reason for me to make a BIG detour whenever I see a Creative product on a shelf.
Axel

Firmware bug: $CCERT must not be used in Report_Rule

Prolog
"Report Rule" can be configured with URL's used to save phone's current configuration. Starting with 7.5.2b firmware it is possible to configure more than one URL here. The semi-colon has been used as separator. It caused issues because semi-colon can be used in casual URL, so the separator has been changed to space in 7.5.5 (see Bug in Report_Rule parsing (SPA50x, fw 7.5.x) for more)
As of 7.5.7 firmware, the 2048 certificates has been introduced and value of $CCERT variable may contain text "Installed (2048 bits)". It cause other issue related to Report Rule parsing.
Issue & how to repeat
$CCERT can be used on "Report Rule" no longer because of wrong parsing order.
The author of firmware first call variable expansion for complete "Report Rule" string, then split the result by space in attempt to found second URL.
With Report Rule configured to https://test.local/Report.php?Product=$PN&CERT=$CCERT it is parsed to:
first_rule is https://test.local/Cisco/Report.php?Product=SPA508G&CERT=Installed, second_rule is (2048 bits)
It is wrong result. In advance, it reveal the characters inserted into URL by variable expansion are not escaped properly.
How to fix
The order of parsing steps needs to be reversed. Report Rule need to be split into parts first, then variable expansion should be called for both parts independently. Also, strings expanded from variables should be url-encoded properly.
Disclaimer
I will not call SMB support to report this bug to them. Assuming the Cisco is interested to repair firmware bugs a staff member monitoring this forum will create ticked by self. I wish that all relevant information including the depth-in analysis has been disclosed here. I'm ready to provide further details or create test environment if necessary. I'm just not willing to call the Support center as I'm not willing to explain all those complex things described here by phone (and they doesn't accept written reports).
For those non-Cisco-staff users affected by issue - feel free to report the issue to Support center, if you are willing to do it. You are allowed to use information disclosed here, or just refer to this report. I don't care the authorship.

Post Author: CompositeID
CA Forum: .NET
You are not alone on this one, I am having the very same issue as you are and . Everything functioned just fine the last time the application was deployed was deployed and there was nothing changed to any of the reports or code which handles the reports; however, this time I am having the same issue. I added the parameters to the report to check to see if they were actually being recognized by the report and they do show up, but it refuses to filter the records and brings back every record. The report works properly if I run it just directly in Crystal though. I sure hope someone can enlighten us Paul.
Update: Well, I finally figured out what was causing my issue. The issue had to deal with the actual older version of the CrystalReportViewer control and the newer version supplied by the update. I had suspected it was something minor that I had overlooked when doing the update. Hope this gets you going as well. Cheers

Linksys E2000 firmware bug for v1.0.02 build 4Jul. 9, 2010

Similar Messages

Maybe you are looking for