Linksys EA2700: No Internet Conection

Im not able to conect to the internet threw my router, but i am able to with my modem. Someone pleese help i dont want to pay for a new one and Cisco wants me to pay $30 for phone support.

RainbowDashBrony64 wrote:
yes it has, it just stopped working one morning
You may try to power cycle first the router and the modem by turning them off and on then check the internet again. If ever it is still not working, follow the suggestions made by thebluemamba_24 if everything work okay from the modem, reset, and reconfigure the router. Check out these sites for instructions:
Setting up a Linksys router with Cable Internet service
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=0ff4c94586a345d082828ec2161aaecf_3686.xml&pid=80&r...
Setting up a Linksys router for DSL Internet connection
http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=3687

Similar Messages

No Internet access without replugging WAN to Linksys EA2700

Every time after the router (Linksys EA2700) is powered off and restarted, there is no interent access available. The router configuration status reports an Internet Address of 0.0.0.0 and all the devices at home are left with a wifi without Internet access. I have to unplug the WAN from the router and plug it in again while it is turned on to restore internet access (and a normal Internet Address is seen from the status page). The WAN works fine with the routers I had previously. I wonder if I have to perform this every time I power on the router. Do you have any suggestions? I have tried resetting the router and reinstalling Cisco Connect but that didn't work.

It would be best to isolate the concern by connecting a computer to the modem. Observe the performance of the modem’s internet connection within 24 hour. If there is nothing wrong with the modem’s performance then you now need to deal with the router. Make sure that the router’s firmware has been updated then reset the router after a firmware upgrade. If you have determined that the problem is really with the router then you might need to return the router and have it replaced.

Problem with linksys EA2700

I've got a problem with my linksys ea2700. one time my network components get an ip-address like 192.168.x.x, the other time they get an ipaddres 10.184.x..x, I want that all my components will get the 10.184.x.x address, how can I solve this problem?

If your modem has a capability to be a DHCP server then just configure your EA2700 router as bridged. In that way, the EA2700 router will just act as a pass through device.
Setting up your Linksys Wi-Fi or Smart Wi-Fi Router to Bridge Mode

No Internet conection!

Since 24 days I have no Internet conection! I have conection by Airport to another computer. Since 24 days I have tried to solve this problem, but I didn´t manage. I tried it several times with the diagnose of Safari.
I asume the problem must be solved in the configuration of Network! Because in the diagnose Airport is colored yellow and the message says that Airport gave itself a code(?) and therefore it´s possible that I don´t have acces to the Internet!
Who has advice?
Eduard Lid
P. s. my computer has returned today of repairs!
MacBook Mac OS X (10.4.11)

Hi Eduard,
Just to clarify here, you're connecting to the Internet on your MacBook via another computer (Internet sharing). That other computer, which is receiving the inbound ISP connection is connected to what? A router? A modem? Is it dial-up, DSL, cable, WAN?
On this other computer, is that computer able to connect to the Internet?
This document should assist with reconfiguring Internet sharing in OS X 10.4
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh336.html

Using CC without internet conection

How can CC programs be used when no internet conection is available? Thanks

Hi Ram2014 ,
Welcome to Adobe Forums
You can go through the link mentioned below and read the first question in the FAQ provided-
http://www.adobe.com/products/creativecloud/faq.html
Let us know if that helps !
Thanks
Garima

TC Internet Conection problems

Hello,
I've had my time capsule for a few months working perfect.
A week ago I started having problems with the internet conection. I've read about different people with similar problems but here it goes:
TC conected to cable modem
iMac OSX 10.8.2 conected to TC via ethernet.
Apple TV, Macbook Air OSX 10.8.2, iPhone, etc conected wirelessly.
I have no access to the internet but the TC light stays green and all the modem lights are on.
So everything seems ok but I just cant access the internet on any device conected to the wireless signal. Sometimes it will work for just a few minutes, sometimes for hours. But keeps doing that all day, for a week now.
I called the internet company and they had some stuff done on their network the same day that I started to loose the internet.
But they have already fixed the problem and I keep getting internet problems.
Should I have the TC replaced?

Factory reset and follow the instructions..
Then reboot the whole network.. restart from off.. everything off..
modem.. wait 2min
TC.. wait 2min
Client computers.
Make sure everything gets correct IP address.
If you have issues, install 5.6 utility if you use lion or even mountain lion.. then you have access to the log.. without it you have nothing.
How to load 5.6 into ML.
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. it is very simple.. drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. drill down.. applications utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall 6.1 so don't try.. and you cannot or should not run them both at the same time.. so just ignore the toyland version.. the plastic hammer.. and start using 5.6.. a real tool.
For screen shots see this post.
https://discussions.apple.com/thread/4668746?tstart=0

Can a Rented movie be seen without internet conection?

Can a Rented movie be seen without internet conection?

Yes. An internet connection is only required when transferring a rental from your computer to or from an iDevice. I watch them all the time on my iPad on airliners without an internet connection.

New computer, downloaded itunes but it says there is an error. cant conect to store. check internet conections. but internet is on and working.

Help...
Just downloaded itunes on new computer. Unable to access itunes story. Telling me to check my internet conections, internet is fine though????

Hi.
I have that issue too. I have disabled the anti-virus plus firewall. I've even corrected the host file but nothing works.

Problems with linksys EA2700 and software issues

Hello
Once I setup the EA2700 wireless router, I was able to setup my Iphone and Ipad and use the internet. Problem is no one else can. I setup the conncetion and use the password on their devices but to no avail. I tried to access the tool software and it keeps coming up with browser not supported,load the newest version of windows, which is strange since it had no issues when I first installed it. I am using Windows 7 Home Premium and have Internet Explorer 11.
Any help is appreciated
James

Hi jcargile. That’s seems odd, because the minimum system requirements for windows web browser is Internet Explorer 8 or higher. You may try using a different browser (Mozilla Firefox or Google Chrome) and then access the Linksys Smart Wi-Fi page again. Once you’re in, you may play with the wireless settings of the router. You can try using channels 11, 6, 3, 9, or 1, pick the one with the best result. By the way, what is the security set on the router? Because most of the time the security set on the router, play a big part.

How to reconfigure my Linksys EA2700 wi fi router

I made the mistake of resetting my router (EA2700) when it was down and now I need to reconfigure it. Can anyone help me or do I need to pay tech support at Linksys?
Thanks

I recommend that you phone contact your regional Linksys support office and ask for help and information...

Linksys EA2700 VS. RV180-K9-NA

have some questions bout these routers EA2700 and RV180-K9-NA 1. can it handle TWC ultime speed 2. is it a very good reliable router i have tried linksys be4 and some werent 3.can it handle several devices all at the same time without slowing down ? btw i know il need a sepret wifi thing for the RV180 whats the better faster more reliable choice ?
Solved!
Go to Solution.

According to scenario if you are more concerned about wired speed than there will not any issue. Since both the router have Gigabit Ethernet Ports.
The basic difference between the two routers is: EA2700 supports DUAL band wireless capabilities where as RV180-K9-NA is used for VPN connectivity but does not have wireless feature.
Here is the link for more information about RV180-K9-NA: http://www.cisco.com/en/US/prod/collateral/routers/ps10907/ps9923/ps11995/c78-697397_data_sheet.html
Here is the link for more information about EA2700: http://homesupport.cisco.com/en-us/support/routers/EA2700

No Internet conectivity/clock error when installing FB4.7 (trial)

I follow these steps:
Install as trial-> (License) Accept -> Sign In Required (Click Sign In) [here I get the error: "Please connect to the Internet and retry: Either your computer is offline or the clock on your computer is set incorrectly"]
I've tried the "Connect Later" option that continues the installation procedure until the end, but when I try to open FB4.7 I get stuck at exactly the same point; it asks me to sign in and I get the same conectivity error.
Any ideas?

Hi Srikishan,
Thanks for your fast answer.
I installed MaxDB DMB GUI from the directory: \NWABAPTRIAL70206_64\MAXDBTOOLS
and logged in with username u201Ccontrolu201D and used the password I gave in the installation.
This was new for me and I learned something new about database management. Thank you for that.
I solved the error but it was just a really stupid mistake from me.
A friend told me once that when installing Netweaver I have to put the date in the future so that the license wonu2019t expire . So before I installed Netweaver I set the date to 2099.
That was the problem, when I didnu2019t do that then there was no error message.
Again thanks for helping.
Regards, Robin
Edited by: Robin Vleeschhouwer on Oct 28, 2011 10:01 AM
Edited by: Robin on Oct 28, 2011 10:01 AM

Airport Extreme, Linksys Router WRT54G: Internet is Impossibly Slow

I have a problem regarding wireless internet activity on my Powerbook G4. In my house, I have a Linksys Router (WRT54G) that has worked fine for other laptops (including an iBook running Airport Extreme, a Powerbook G4 running Airport, and an iMac running Airport) for many years. When I got a refurbished Powerbook G4 1.67 GHz with Airport Extreme, I found that while Airport could be configured to recognize the wireless network (with a WEP 40/128-bit encrypted key), it barely works on the computer. The signal strength is strong (the laptop is hooked up right above the Linksys router), but the Internet barely works at all. Surfing to webpages takes 10-20-30 sec to work, and often the connection seems to drop off all together. Something is clearly wrong because despite the fact that this is my fastest computer with the fastest wireless capability, it runs at a slower pace than any computer I have ever used on the web.
I was wondering if anyone has had similar problems with getting Wireless Extreme on Powerbook G4s to work with this particular (and older) model of Linksys wireless browser (WRT54G). Some Internet sleuthing led me to believe that perhaps the router firmware needs to be updated or something like that, but I haven't really found any definitive answers. If there is anything wrong on the laptop-OS-side, I have no idea. I would appreciate any pointers that you can provide!
Thank you to all,
Matthew
Computer:
Powerbook G4
1.67 GHz
1 GB DDR SDRAM
OS 10.4.8
Wireless Router:
Linksys
Model: WRT54G
Powerbook G4 Mac OS X (10.4.8) 1.67GHz, 1GB DDR SDRAM

Hi all,
Thank you for your help. Unfortunately, my problems persist.
I was able to reset my router and to configure it again on the web-based router configuration.
As per your suggestion, I tried switching the Wireless Network Mode to "G-only." Not only did this kick off my older computers on the network (an old iMac and an older Powerbook G4, both with normal airport), but it did not fix the speed problems on the new Powerbook G4/with Airport Extreme. I am back on the mixed setting now in order to get most of the computers on the network back to their old working states...
I also tried disabling my WEP encrypted key but found that this did not speed anything up at all.
I have upgraded my firmware from its previous version, v 1.41.2 (very old!), to the latest from the Linksys website: v 4.30.5. This has not helped at all either.
Is it possible that there is any setting on the Powerbook/Airport Extreme itself that is causing these problems?
Thank you all again for your help,
Matthew
Powerbook G4 Titanium Mac OS X (10.4.7) 1gHz, 512mb RAM

G3 and wireless internet conection

I have a 2yr old indigo iMac. I just bought a new iMac g5. How can I set the old machine up for a wireless Internet connection? I have a designated line for dsl in my home office and I want to put the older machine in another room for the wife & kids.

If this is an indigo 250 mhz iMac, there is no airport slot to install a card into. Only the blueberry 350 mhz machines and 400 mhz and up machines have airport slots. if you do have an airport slot, you also need the airport card adaptor.
Another option is ethernet based wireless bridges like those from linksys, dlink, belkin or macsense. Avoid usb based ones. nothing but problems with those.

Linksys ea2700 in bridge mode

I *think* I have my ea 2700 setup for wireless bridged mode, using this article:
http://kb.linksys.com/Linksys/GetArticle.aspx?docid=28cee6a2fb0d4176a2210942d1d5836c_Setting_up_the_...
however, I notice that that article doesn't say anything about the wireless setup of my ea 2700 - do I configure it? In other words, when you setup your router in bridged mode, do you see two wireless networks, the old one and the new one? Or does the bridged router become like an antenna for the old router? I have a 2wire Uverse wireless router (the old router) - I can still connect to it after the ea2700 bridged setup. I can't connect to my new ea 2700 - it doesn't seem to like the password. Am I supposed ot be able to connect to it?

There’s a quick tip on that link you posted above (below) which I suggest you should do:
QUICK TIP: The Wireless Network Name (SSID) for each router must be different to avoid conflict for devices which will connect to the wireless network
To manually setup the wireless settings of your router, follow the steps from this link: http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=22532.

Linksys EA2700: No Internet Conection

Similar Messages

Maybe you are looking for