Linksys router not compatible with os x maverick

is any body has the same problem.

HI,
I asked four questions.
You answered one of those.
You are not going to progress very fast at this rate.
The PortForward.com site has a set of Screen Shots of this device http://screenshots.portforward.com/routers/Linksys/E3200/
I was looking at them and found this on the Wireless set up page
I am not familiar with this PIN number method.
I am presuming the Manual option provides the SSID name and the Passphrase  that other routers may use for WPA encryption.
There is also a page on USB Connected Drives being used suggesting it has similar capabilities to an Apple Time Capsule.
Therefore the device is not that old.
It can be Wireless.
How you are connected to it I still have no idea.
7:22 pm      Sunday; December 1, 2013
  iMac 2.5Ghz 5i 2011 (Mavericks 10.9)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad

Similar Messages

  • IPod 4,1 will not update to iOS 7. I updated my iMac to 10.9.1 (maverick). Latest Numbers version on iMac is not compatible with Numbers on iPod. Ideas? Can I go back a version with Numbers?

    iPod 4,1 will not update to iOS 7. I updated my iMac to 10.9.1 (maverick). Latest Numbers version on iMac is not compatible with Numbers on iPod. Ideas? Can I go back a version with Numbers? I downloaded old version of Numbers 2.0.1 from DVD but with both versions the 2.0.1 will not open.  So both versions are present but only the new version functions. I tried to drag the new version to the trash but the old version still runs error message and will not open. I did not try to restart with the new version in the trash.

    Maybe. See:
    Reverting to previous version of Numbers

  • Be Warned - Mavericks is not compatible with Microsoft Office 365!!!!!!!!!!!!!!!

    Be Warned - Mavericks is not compatible with Microsoft Office 365!!!!!!!!!!!!!!! 
    I upgraded to Mavericks on 4 seperate computers, an 2 iMacs, MBPro and an MBAir and ALL four no longer connect to Microsoft Office 365 email accounts either with Office 2011 or the built in Mac apps.  Apple support says "Microsoft knew for a year that Mavericks was coming out and it their job to make it compatible".  I repsonded that their own Apps like Mail, Contacts and Calendar don't work either and they attempted to trouble shoot those apps only to no avail after 4 hours and a Mavericks reinstall.  I have also tried an Office reinstall.
    Right now I am no where, stuck between two companies who say it's the other guys fault......

    Me again:
    A colleagues more formal description of the problem:
    We have had a major problem with people working directly off of the afp reshares with MS Word.
    Word creates "Word Work Files" and usually is able to store them in either "Share/Temporary Items/uid/TemporaryItems/" or "Share/.TemporaryItems/folders.uid/TemporaryItems" as long as permissions are correct.
    This works under 10.5.7 seed release 9J39 with direct attached storage, but with the Xsan reshared the word work files appear in the same folder as the opened document even though the permission for temporary items are correct.
    This causes a number of issues, one being that if one user has a document open and another clears out the word work file then the open document cannot be saved.
    Another issue that we have seen is where the word work file is created and then the original document disappears (although I think this may be another user housekeeping the word work files again).
    We have tried to persuade users to work on local copies of the documents instead, but old habits die hard...

  • How do i reinstall mountain Lion after installing maverick. Maverick  is not compatible with FileMaker 13 server. Maverick is now objecting to reinstalling Mountain Lion. Where do I go from here? Help?

    How do i reinstall mountain Lion after installing maverick. Maverick  is not compatible with FileMaker 13 server. Maverick is now objecting to reinstalling Mountain Lion. Where do I go from here? Help?

    If you can download the ML installer you can make a bootable install media by using:
    http://liondiskmaker.com/
    If your Mini came with ML you can also boot to Internet Recovery
    OS X: About OS X Recovery
    and it will install ML. Make sure you boot to Internet Recovery and not the Recovery Partition. If to the partition you will only get Mavericks.

  • Disk utility 12 not compatible with Mavericks

    I upgraded my late 2008 Mac Book Pro to Mavericks several months ago and just tried to open Disk Utility and get a message that the version I have is not compatible with Mavericks.  Mine is Disk Utility 12, is there an upgrade available?  I looked on the Apple site and couldn't find one.  Thanks!

    Well, I'm not on my Mavericks machine at the moment, but my Mountain Lion machine has Disk Utility 13, so Mav must have at least that or higher.
    Since Disk Utility is not a stand alone application, but an integral part of the OS, I'd suggest you use your recovery partition - hit Command + R keys during restart/boot up and choose to reinstall the OS. That should bring everything up to date.

  • CS5 not compatible with Mavericks 10.9.3?

    I just spent 2 grands with the new iMac Mavericks 10.9.3 and now someone told me all my CS5 apps are not compatible with it and I have to upgrade?  Seriously????

    CS5 is unsupported. It might work, it might not but you're on your own.

  • Epson Stylus Photo PX710W is not compatible with Mavericks

    I still cannot scan with my Epson Stylus Photo PX710W. My scan driver (scan.app version 3.7.1) is not compatible with Mavericks. Who can help me?
    Epson does not react to my question when the correct driver will be available.
    Epson indicate to their FAQ’s, but this is will not help since the ICA scan only works when my printer/scanner is connected to my Mac via USB. I bought this EPSON printer/scanner because it was wireless. Now after just 3 years I miss this important option.
    I see a lot of discussion about Epson scan drivers but little help from Epson
    Who can lead me to an appropriate scan driver for my Epson device?

    I disagree a bit because my Epson printer/scanner worked very well for over 3 years. It worked under Snow Leopard, Lion and Mountain Lion. But since I installed Mavericks my scanner doesn't work anymore. It's just a case that Epson is very slow in upgrading the drivers within an appropriate time on the one hand and not giving any foresight how long it takes to repair drivers on the other hand. Their website is inadequate and gives me absolute no information at all. I can understand their vision when it comes to printer/scanners which are very old i.e 10 years and mor. But not for relatively new printer/scanners.
    So, if anybody can help i'll be very greatefull.

  • The truesuite is NOT compatible with Mavericks!!!!!

    The truesuite is NOT compatible with Mavericks!!!!! Do you wanna solve this problem in a short time? Please HELP me!!!!

    http://support.apple.com/kb/TS5338?viewlocale=en_US&locale=en_US

  • HT2476 I recently upgraded to OS X Mavericks and now I cannot open any of my Microsoft apps. Is Mavericks not compatible with Microsoft Office 2008? If not, how do I revert back to Mountain Lion?

    I recently updated my Macbook Pro to OS X Mavericks and now I cannot access any of my Microsoft Office apps. Is Mavericks not compatible with Microsoft Office? If not, how do I revert?

    Welcome to Apple Support Communities
    Office 2008 and 2011 are compatible with OS X Mavericks.
    If you are using Office 2008, I highly recommend you to reinstall the latest Office 2008 update > http://www.microsoft.com/en-us/download/details.aspx?id=36897 Note that Office 2008 is not supported by Microsoft anymore

  • What wireless router is compatible with Mac OS X 10.8.1?

    I just purchased a new cisco Linksys wireless router that is not compatible with OS X 10.8.1.  Which routers ARE compatible, besides the Apple AirPorts?

    Your Linksys router should be compatible, however the firmware might need updating once you get online.
    Your router will have an IP address in the ranges 192.168.1.1 or 10.0.1.-
    Connect your router to your Mac via Ethernet cable (They usually supply one with the router and don't worry which end goes where the Mac LAN socket is bi-directional)
    Also connect your router to your telephone line - Its likely you have an ADSL service because if you have a cable service they provide a modem normally.
    Now open your Web browser (Safari is the only one installed be default) . Type in the IP address and a Javascript control panel will launch
    Enter the default password and username (They are on a label on the router )
    Your now have the ability to set up your router.
    Your will need the password and user name supplied to you by your ISP at a minimum.
    Enter these and most modern routers automatically configure the basic networking setting.
    You now need to go to the security setting and set this as WPA2 Personal (NOT Enterprise) or WPA2 with AES and TKIP which ever it refers to and create a pass-phase. WRITE it down
    You should be online.
    Your router may need a firmware update LInksys units usually do but that is a different and long story for a separate thread.
    Personal experiences with Linksys routers in the Mac evironment are not so good and they have tended to get hot lock up or fall over from time to time resulting a hard reboot being necessary.
    To-date the very best and most stable performance has been with an Airport Extreme/Time capsule connected to a cable modem.
    Regrettably you still need a separate modem to use this with ADSL services.
    Shootist007 the fact that Apple use a separate full application (Actually two are available at the moment 5.6 for enterprice and 6.1 for home networking) gives direct control rather than relying on javascript and firmware errors.
    Its actually a better solution

  • I downloaded CS6 and am having issues with my print driver. It is not compatible with the HP 2600n and have tried to download drivers given to me by adobe ( (Jupiter 3) but it is not working. after a few days. Its a temporary fix and is still looking for

    I downloaded CS6 and am having issues with my print driver. It is not compatible with the HP 2600n and have tried to download drivers given to me by adobe ( (Jupiter 3) but it is not working. after a few days. Its a temporary fix and is still looking for the HP driver when i boot up. It also will not save in any print or postscript format. Does anyone know how to fix?
    Currently use a Mac with the latest Mavericks 10.9.4

        Oh boy! Acting kind of weird seems to be an understatement, aquaequus!
    What type of troubleshooting were we able to do with you? I want to make sure that we can get some sort of resolution for this problem.
    It is quite possible the battery door may get your phone in working order again. I'm not sure if the store has it in stock, but it is available in our warehouse for $14.99 which can be ordered via customer service.
    Tamara H.
    Follow us on Twitter @VZWSupport

  • Font Book "not compatible" with 10.9 after upgrade from 10.7

    I upgraded from os x 10.7 to 10.9 on my iMac and now my font book won't open. I keep getting a message that says my version of font book is not compatible with 10.9. Is there a way to reinstall font book?

    No,
    You should download and install the 10.9.4 combo update. OS X Mavericks 10.9.4 Update (Combo)
    As with any system upgrade or update it is wise to backup first.

  • Cannot update to 3.5 on older MacPro and 3.5 not compatible with 3.4.5

    It appears that you cannot update Aperture to 3.5 on older Macs. Worse yet the new update is not compatible with the previous version.
    The questions are  ---
    Is this a temproary issue or a permanent issue?
    Can I regress back to version 3.4.5 to get my compatibility back ?
    I have multiple computers I use to work on my photography.
    I use a older Mac Pro Vintage late 2007 that cannot be updated beyond OS 10.7.5. This is currently my primary photo computer.
    With 3ghz Quad cores and over a terabyte of drive space no need to update yet except for not being able to load the latest OS.
    I also use a MacBookPro Vintage Late 2011 and it was just updated to Mavericks. I use this to edit my photos on the go.
    I will consider updating to the latest Mac Pro when it becomes available but what to do until then and a warning to others.

    Actually, I had this same problem - accidentally upgraded my library on my Mac Air to 3.5, but am not running Aperture 3.5 on any of my other, older Macs.  I *was* able to downgrade the library back to 3.4.5.  BAsically, I had to open the library on a computer running Aperture 3.4.5 in library repair mode (holding down command and option when opening).  In the ensuing dialog I had to choose to rebuild the library.  I first tried just repairing, and it seemed to work, but next time I opened Aperture I got the "library can't be opened iwth an older version of Aperture" message.  Rebuilding it seems to have done the trick.
    A more detailed explanation (though not written for this particular scenario) is here:
         http://www.apertureexpert.com/faq/common-aperture-questions-issues-and-rep/how-d o-i-repair-or-rebuild-my-aperture-library-or-permission.html
    Having restored the library to 3.4.5 format, I downgraded Aperture on my Air to 3.4.5 as well and it's been smooth sailing.  Just make sure you have Mavericks set up to *NOT* automatically update your apps, or you'll end up in the same situtation all over again when it silently upgrades Aperture to 3.5 again.
    Good luck!

  • I just upgraded to os 10.9.5. When I try to open iPhoto, I am told that the version I have(9.3), is not compatible with the os. But it came with it when I upgraded. What do I have to do to get an iPhoto that works with 10.9.5? TIA

    I just upgraded to os 10.9.5 on my 15 " macbook pro from os 10.7.5. When I try to open iPhoto, I get the message that it is not compatible with the os. How can that be??? It came with the upgrade. It says the version of iPhoto is 9.3. How do I get an iPhoto that works with os 10.9.5? TIA

    This screenshot shows which previous versions of iPhoto are compatible with Mavericks.  It also indicates which versions qualify for a free upgradeto iPhoto 9.5.1 and which require a purchase:
    Note 1:  every day more users are reporting problems with iPhoto 8.1.2 so I've included it in the non compatible category.
    Note 2:  If your previous version of iPhoto was iPhoto 7 (08) or earlier you'll need to download and run the iPhoto Library Upgrader 1.1 application on the library before opening it with iPhoto 9.5.1

  • ICloud apps Not Compatible with older versions if iWorks

    CAUTION
    If you haven't upgraded to the new version of iWorks that was released with Mavericks today, do NOT open any of your files in iCloud. If you do, you will no longer be able to open them with your older versions of the iWorks apps.
    For example, Apple today released Pages version 5.0. The last version of Pages was 4.3 (released in Dec 2012). If you create a new document in Pages 4.3, save it to iCloud and then open it in iCloud using Safari, you will no longer be able to open the same document in Pages 4.3. When you try, you'll get an error that you need a newer version of Pages.
    In other words, it's now imperative that you upgrade to the latest version of the iWorks apps that were released today as the earlier versions are NOT compatible with the iCloud apps.
    Hope this helps.

    The FAQ for iPad Pages has always made it clear that Pages import and export formats were Pages 09 only.  Nobody here can tell why Apple made it that way, but you can give them your views here:
    http://www.apple.com/feedback/pages_ipad.html

Maybe you are looking for

  • GTC Creation Problem with OIM9.1.0.1866.50 BP12

    Hi, I have installed OIM 9.1.0.1 on OAS. After BP12 was installed, I can't create a GTC connector (step 3: Modify Connector Configuration). An error ocurres when I try to do the following steps: -Create a new field in OIM stage ( String, 100 chars, m

  • Infospoke data extraction fail

    Hello Experts, I created an infopoke for my cube and extracting the data into a DBtable. I get this error: 'Unable to activate the table /BIC/OHZISPKA1' Where ZISPKA1 is the infospoke created. Any suggestions appreciated. Thanks, SWM

  • Migrating data from LookUp Table to Main Table without taking extract

    Dear Experts, Is there any way if we want to migrate full data from LookUp Table to Main Table in the same repository without taking the extract from MDM DM and not importing it using Import Manager? Thanks Gaurav Kumar Sharma

  • Sim card tray will not open

    I cannot get the sim card tray to open

  • Image of cluster

    hello, I my App. I need to print several controls into a JPEG file. I am able to use the "Get Image" method (and Get Image Subset VI) with every control except one: a cluster. Look into the attached VI. Could someone tell me how I could print the com