Linksys Router WRT54GS ver.6 Power Adapter AC 100 - 240V

Were can i buy a Power Adapter Input Voltage: AC 110 - 240V and Outputs: 12VDC  500ma for Linksys Router WRT54GS ver.6
thanks
Message Edited by stewartroberts on 05-27-200706:01 PM

I have  a couple for sale. I am asking $12 a piece if you are interested.

Similar Messages

  • Is the power adapter rated 100-240v for the HP Stream 13 Laptop ?

    Hi,
    I want to buy it. and i want to be shore about the voltage...
    .....Is the power adapter rated 100-240v for the HP Stream 13 Laptop ?
    Thank You.

    I might have tested it myself a few months ago, I cannot remember the results but I believe booting from the SD slot is not supported by the UEFI firmware. It is mentioned here in the comments of this Amazon review for the Stream 11: "I have not been able to boot ANYTHING from the micro-SDXC slot. I can install Ubuntu on it, but I cannot boot from it. I don't know if booting is even possible."

  • HELP I have a wireless Linksys router WRT54G connected th...

    HELP I have a wireless Linksys router WRT54G connected through my cable company broadband modem on a Mac. I have another computer to which I installed wireless capability because it didn't come with it. This required attching some piece of equipment to the back of the PC which enabled it to get on the internet without another cable modem. My question is this. If I get an iphone or a laptop(with built in wireless ability) will I automatically be able to go on the web because of the router on the Mac.

    yes certainly... if you get any wireless device in network that would certainly connects to a wireless n/w of router...

  • Airport Extreme, Linksys Router WRT54G: Internet is Impossibly Slow

    I have a problem regarding wireless internet activity on my Powerbook G4. In my house, I have a Linksys Router (WRT54G) that has worked fine for other laptops (including an iBook running Airport Extreme, a Powerbook G4 running Airport, and an iMac running Airport) for many years. When I got a refurbished Powerbook G4 1.67 GHz with Airport Extreme, I found that while Airport could be configured to recognize the wireless network (with a WEP 40/128-bit encrypted key), it barely works on the computer. The signal strength is strong (the laptop is hooked up right above the Linksys router), but the Internet barely works at all. Surfing to webpages takes 10-20-30 sec to work, and often the connection seems to drop off all together. Something is clearly wrong because despite the fact that this is my fastest computer with the fastest wireless capability, it runs at a slower pace than any computer I have ever used on the web.
    I was wondering if anyone has had similar problems with getting Wireless Extreme on Powerbook G4s to work with this particular (and older) model of Linksys wireless browser (WRT54G). Some Internet sleuthing led me to believe that perhaps the router firmware needs to be updated or something like that, but I haven't really found any definitive answers. If there is anything wrong on the laptop-OS-side, I have no idea. I would appreciate any pointers that you can provide!
    Thank you to all,
    Matthew
    Computer:
    Powerbook G4
    1.67 GHz
    1 GB DDR SDRAM
    OS 10.4.8
    Wireless Router:
    Linksys
    Model: WRT54G
    Powerbook G4   Mac OS X (10.4.8)   1.67GHz, 1GB DDR SDRAM

    Hi all,
    Thank you for your help. Unfortunately, my problems persist.
    I was able to reset my router and to configure it again on the web-based router configuration.
    As per your suggestion, I tried switching the Wireless Network Mode to "G-only." Not only did this kick off my older computers on the network (an old iMac and an older Powerbook G4, both with normal airport), but it did not fix the speed problems on the new Powerbook G4/with Airport Extreme. I am back on the mixed setting now in order to get most of the computers on the network back to their old working states...
    I also tried disabling my WEP encrypted key but found that this did not speed anything up at all.
    I have upgraded my firmware from its previous version, v 1.41.2 (very old!), to the latest from the Linksys website: v 4.30.5. This has not helped at all either.
    Is it possible that there is any setting on the Powerbook/Airport Extreme itself that is causing these problems?
    Thank you all again for your help,
    Matthew
    Powerbook G4 Titanium   Mac OS X (10.4.7)   1gHz, 512mb RAM

  • Linksys Wireless Card (Linksys Router) in G4 Power Mac works fine until...

    Linksys Wireless Card (Linksys Router) in G4 Power Mac works fine until...
    new software upgrades on the 14 August 2006 (yesterday) which includes Airport 4.2.
    The Linksys wireless PCI card (WMP54G) was installed just under a year ago with no problems. There was no need to install drivers, the Apple Mac recognised it and used it as a wireless card. I was browsing the internet last night (14 August) and the software updates downloaded in the background. Once it finished downloading, it requested for a re-start. I carried on browing the internet and then switched off my machine and went to bed.
    When I turned on my computer in the morning, the wireless card no longer activates. The computer recognises there is a card but there is no connection to the router (meaning no internet). The router settings have not changed at all.
    I believe it could be the Airport 4.2 update has interfered with the Linksys Card, but I'm not sure. I've been through all the Assist functions etc and there is no luck. It does seem that the big update released on the 14th August has played its part.
    Any opinions and assistance on getting the card back to normal, and if possible assistance in removing the new updates to previous drivers/settings.
    Thanks people.
    G4 Power Mac Dual Processor Mirrored Doors   Mac OS X (10.3.9)  

    Sorry, I do not have a solution for you but I have the same problem upgrading from Jaguar to Panther (on my home machine not listed which is a G3 b&w). Now my WMP54G doesn't see any wireless network (I used to be able to see several in the 'hood), and Apple Profiler recognizes the card. Apple updater changed the Airport system files, I believe.
    Is it possible to find the old Airport software and install over current system to get it working again? I doubt Apple still offers the old airport software, but if someone has it, maybe it can be installed with Pacifist.
    We need some wireless help here, community.
    2.5 GHz Dual PowerMac G5 | 3GB RAM | SuperDrive   Mac OS X (10.4.6)  

  • Linksys router wrt54g works with pc laptop but not mac desktop

    i have a linksys router wrt54g. using my pc laptop i configured the router with a wep password. my pc laptop asked for the wep once and has no problems connecting everytime i turn it on. my older(powermac2,1) desktop (mac os x) asked for a wep password i entered one of the four given me by the router and it worked. on later attempts to access the router i have been unsucessful. i am asked for a wep password and when i enter it i am told the password is not correct. when i reset the router, airport has no problem connecting but i have no security. also i can't access the router online like i can with the pc laptop.
    can anyone help???
      Mac OS X (10.4.8)  

    try a "$" before your password

  • Linksys Router WRT54GS keeps timing out after Lion upgrade

    Since we upgraded to Lion we keep loosing wifi and Internet. Have to switch off the router. Then it works again for about a few minutes.
    Please help!
    Router is Linksys WRT54GS
    Lion is: 10.7.1
    Thanks in forward
    Bernhard

    Batteman87 wrote:
    I've had the exact same issue. Same router and everything. Worked like a charm with Snow Leapord but since the update it doesn't.
    Unfortunately the WRT54GS is from 2005 and there are not longer Firmware updates available for that model.
    http://homesupport.cisco.com/en-us/wireless/lbc/WRT54GS
    On Mac's there is problem with wireless access points using a 2.4GHz/5GHz mixed mode if both parts of the wireless network have the same name (SSID) but due to technical rules two different addresses (BSSID) for the different wireless modes.
    On that the Mac switches between the radio bands to provide allways "the best" connection.
    That causes disassociation from the wireless what shows you then the well known effects in your wireless.
    Also a band hopping "Guest Network" may disturb the connection if there is no dedicated name (SSID) is set for the Guest Network.
    On the WRT54GS
    Check that the "Guest Network" is disabled.
    Check that WPA2 Personal AES (not TKIP) is the security mode. See -> http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=22050
    Eventually change network mode from mixed (default) to "wireless-N Only" or "wireless-G Only" if the 2nd BSSID cause trouble with the Mac. -> http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=22555
    On the Mac
    Generally follow the instructions here -> http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=15805
    On System Setup - Airport (WiFi) main page uncheck (disable) "Ask to join new networks"
    Eventually set up a new location for your home network.
    Eventually delete all obsolete wireless networks from the "known networks" list including your WRT54GS
    Delete also the corresponding key's from Kechain Acceess
    Reboot the Mac
    Configure your home wireless on the Mac from scratch.
    Eventually try the Linksys Forum to find more information.
    http://homecommunity.cisco.com/t5/Wireless-Routers/bd-p/Wireless_Routers
    Regards - Lupunus

  • Wireless Problem, Router WRT54G Ver. 6

    Hello,I recently i bought a Wireless WRT54G router so i could play my Xbox Live wirelessly. However, when I am playing on the Xbox I do not get internet on my computer (yes, the router is wired via ethernet to the computer). When I am on the computer the Xbox gets no signal. So what I am saying is I can only use the computer or the Xbox at once, not both at the same time. I have called Technical Support 2 times, and they told me to download the newest firmware, I did that and I am still having the same problems. I am decent with computers, like i usually fix my own computer stuff, but this one is really not making sense. Any help is greatly appreciated. Thank You.

    The Xbox web site does not list the WRT54G version 6 as being compatible with Xbox 360.   They do list versions 1, 2, and 3 of this router as being compatible.  Are you sure that version 6 works?
    Also, have you power cycled your entire system (modem, router, Xbox and all computers) since the last changes were made.  If not, please do this, then retest.

  • I just got a Linksys router (WRT54GS), and when I get to step 8, it keeps asking me for a password?

    I recently got a Wireless-G Broadband Router modele WRT54GS. When I get to step 8 on the setup disk, I press "Next", and it starts to check my computer's settings. It then asks for a password, so I enter "admin" like I've been told. It starts to check my computer's settings again, and then asks for the password. It keeps happening. Am I doing something wrong?
    I have Windows 7. I'm getting signal, but it's not letting me connect to the internet at all (except for Google, for some reason). Oh, and it's brand new, straight out of the box. Thanks.

    Perhaps you need to do the manual way of setting up the router.
    For Cable connection, here's the procedure.
    For DSL connection, here's the procedure.

  • Linksys Router WRT54G v.4 Problems

    Slow sluggish connection just like everyone else. Previously I fixed this problem by adding DNS Servers: 4.2.2.1 and 4.2.2.1 to the list and this fixed the problem. This worked great for a few months then all of a sudden that stopped working and the DNS settings are preventing my connection. If I take the dns servers out of the list the connection works again but its slow and sluggish again. Anyone have any ideas? Linksys blames apple as usual.
    Any help or ideas is greatly appreciated.

    When you allow your Linksys to provide the DNS server information, are the DNS servers being provided the ones your ISP recommends?

  • Linksys Router WRT54G

    I reset my router today and when I go through the setup it asks for a password when it checks my computer settings I have no idea what password it wants so I try everyone I know, No dice. Is it asking for the password that came in th box or something? cause I lost the book. Can anyone help?

    As you reset the router, it went to the factory default settings...and as the router's default password is admin, you have to type the password as admin in lower case...do not type anything in the username. 

  • HT201700 can I use the usa power adapter in china?

    I've just move to china and I don't know whether I can use the same power adapter 60W, 100-240V I brought from USA

    thanks

  • WRT54G ver. 2 stopped working online

    Hello, just recently my wireless router (WRT54G  ver. 2) stopped working online. Two nights ago I believe it stopped. I can still go online when I plug my computer directly into my modem (Linksys BEFCMU10  ver. 4).
    ~ Both of my wireless adapters (WUSB54G  ver.  4) still can connect to the router, of course they don't recieve internet either.
    ~ I verified everything was plugged in, and nobody unplugged it the day it stopped working.
    If you have any questions, please ask.
    Thank you.

    did you had a power surge or thunder storm in your area? coz sometimes it can affect the settings on the router
    have you tried unplugging both your modem and router for a few minutes and plugging them back in? were you still unable to get internet back?

  • WRT54G ver.6 Admin page not available

    Hi, Two days ago I saw on linksys website new firmware and decided to upgrade.I guess the installation went wrong, and my router WRT54G ver.6 ended up faulty. The problem is that I cannot access the router's Admin page (http://192.168.1.1), the browser gives me message "connection interrupted - The connection to the server was reset while the page was loading." The power light on the router when it starts is steady, no blinking. I can ping the router and as far as I can see it's fully functional in its default mode. I can access internet via cable and wifi. The ssid is Linksys.
    I tried all kinds of hard reset, I guess evertything I could find on your forum. 
    Is there hope for my router or is it "Bricked"? 
    Thanks for your Help
    S...

    Hard reset your router -
    Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
    Also make sure that your computer is set to 'Obtain IP Address Automatically' , disable any firewalls, security softwares on the computer before trying to access the setup page...
    If it does not work try connecting a different computer/laptop to the router's ethernet port and see if you can open the setup page...

  • WRT54G ver.6 "Dead ?"

    I need some Help i have a linksys wireless router WRT54G ver.6.(Vista)  It was working fine for years then I come home from work and can't get internet.  By-passed router and I get internet.  All lights on router are saying working ok but can't get a connection. I can't even long onto the IPS address for the set-up? I tried all of the Vista repair but gives me an answer at the end can't fix problem.  I'm ok with computers but not an expert. but I'm thinking it's a readability problem with the internet?  Any help or maybe it's time to buy a new one?  Thanks

    Have you tried a hard 30-30-30 reset? First power off your router and remove all cables.  Then plug back in the power cord and let it boot.  When the power light stops blinking and is solid, locate the recessed reset button and press it in holding for 30 seconds. Remove power while still pressing in the reset button for 30 seconds more. Place power back to router for 30 last seconds and release the reset button.  Power off the unit and plug your main PC back into port 1 and your modem back into the WAN port. Power on and reconfigure your settings.  Test unit to see if your internet functionality has returned.

Maybe you are looking for