Linksys SPA3102 "flashing" and incoming call problem.

I tried to do as much research as I could before posting, however i'm stuck =/.
My Setup:
Phone Port on wall Split into three phone ports, one with a fax in it, one with a splitter, one empty.
From the splitter I have a line into a D-link modem and a line into the back of the SPA3102.
From the D-Link modem i have an ethernet cable plugged into the SPA3102 [im not using the inbuilt modem, should i be ?]
Also from the D-link modem i have a D-link wireless router.
Then I have a line into a set of Telstra V900 cordless phones from the SPA3102.
I also have another phone connected directly to the PSTN line in another room.
The problem is when a call is coming in on the PSTN line the phone connected directly to the PSTN line rings however the phones connected to through the SPA3102 don't register the call until much after the PSTN phone does. I'm not sure how to go about fixing that.
Also should I pick up on the wired PSTN handset, how do I go about switching to the wireless handset. "flashing" i think it's called.
NOTE: I'm in the market for new wireless phones anyway as the telstra V900 ones are crap, any recmomendations ?
Any help would be appreciated.

First I didn’t understand what you meant for “I’m not using the inbuilt modem” for the SPA-3102. Did you mean you set the SPA-3102 as a bridged?
If you are using a phone splitter where one of the 3 phone ports is connected to the PSTN portion of the SPA-3102 and the other phone splitter port is into another phone and someone calls the PSTN line, the phone connected to the splitter will really ring for it gets a share of the signal coming from the splitter. The phone connected to the phone port (FXS) port for the SPA-3102 will ring only if the PSTN signal has successfully transferred the call to the from the PSTN line registration to the actual Line 1 registration. If that is not happening, there are some registration settings you need to check in the SPA-3102. One important parameter is the registration status of the Line 1 and PSTN lines. You can check that under the Info section just make sure you are login as admin advanced login with the SPA-3102. You should be getting registration state “registered” confirming that the VoIP information you set in the SPA-3102 is valid. If registrations are correct, maybe you need to know is the PSTN Line is transferring the call to the VoIP line section. Setting up this portion is discussed in this link:
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=5159&p_created=11686...
Hope this helps.

Similar Messages

HT1413 how to set the ringer to flash the camera flash for incoming calls

I have seen other iphone 4 have their riinger set up to flash the camera flash for incoming calls. I have not been successful to figure it out from the settings feature. does anyone know how to do this?

Hi jdflo50,
The feature you are talking about was introduced in iOS 5 Software Update v1.0:
http://support.apple.com/kb/DL1456
Accessibility improvements
Option to light LED flash on incoming calls and alerts for iPhone 4S and iPhone 4
Settings > General > Assessibility > LED Flash for Alerts
Hope this helps!
- Judy

When I have my handsfree plugged in, the sms-tone and incoming-call ringtone is only played in my earpluggs. Any suggestions anyone?

When I have my handsfree plugged in, the sms-tone and incoming-call ringtone is only played in my earpluggs. Any suggestions anyone?

I experience the same problem and it's extremely annoying. Have you found a solution yet?
Of course one might want to keep the earphones plugged in most of the time (if this is the way you prefer to answer you calls + talk on the phone) even if you're not using the phone/earphones. The ringtone does come through to to the speaker when someone calls… yet the sms signal DOES NOT and only plays in the earphones.
This means that the earphones must be unplugged after every call and then plugged in again before every call in order not to miss any sms:es! (Talk about unsafe driving e.g.!)
It would seem to be such an obvious setting/option to include in the iPhones settings. Why has Apple has completely missed this!? .... or is there a solution?
I have searched the internet but haven't found a solution?

I've installed ios 7.0.6 on my iphone 4 and lost voice on outgoing and incoming calls. My simm is ok, i've checked it, I've done a full clean and restore. Still no calls. Please help.

Hi there,
I've just installed ios 7.0.6 on my iphone 4 and now lost voice on outgoing and incoming calls.It rings on incoming and I'm told rings on the recipient's 'phone, but then no vocal communication...its just dead. My simm is ok, i've checked it, I've done a full clean and restore of the 'phone. Still no calls.
I've not caused any physical or water damage to the 'phone. I would welcome any help/suggestions to get my calls back asap.
Please help.
Miss liberty

Have you tried restarting or resetting your iPhone?
Restart: Press On/Off button until the Slide to Power Off slider appears, select Slide to Power Off and, after It shuts down, press the On/Off button until the Apple logo appears.
Reset: Press the Home and On/Off buttons at the same time and hold them until the Apple logo appears (about 10 seconds).
Also consider deleting and reinstalling the Mail Account in question.

Droid 2 Global Issues - notif. bar and incoming calls

Ok, I've had my Droid 2 Global for about a year now, and for the most part it has been fine. However, on the latest couple of updates, some really annoying "features" have come up. On the current update, the notification bar disappears randomly. Not known cause. Also, if the notification bar disappears, when I receive and incoming call, it doesn't display the "answer call" screen, showing the contact. This makes it difficult to answer the call, especially when the screen is locked. I have to go unlock the screen, and go to a screen like I'm going to call someone, and THEN I can see who is calling and maybe answer. If it hasn't gone to VM already. This is really stupid - first and foremost, this thing is a FREAKING PHONE. I should be able to answer a call.
Frustrated. Any ideas/help?
Thanks,
-Dirv
Details
=============
System version: 4.5.629.A956.Verizon.en.US
Android version: 2.3.4
Kernel version: 2.6.32.9-g177d714 mcbk83@il93lnxdroid01 #1
Build number: 4.5.1_57_D2GA-59

Ok, I've had my Droid 2 Global for about a year now, and for the most part it has been fine. However, on the latest couple of updates, some really annoying "features" have come up. On the current update, the notification bar disappears randomly. Not known cause. Also, if the notification bar disappears, when I receive and incoming call, it doesn't display the "answer call" screen, showing the contact. This makes it difficult to answer the call, especially when the screen is locked. I have to go unlock the screen, and go to a screen like I'm going to call someone, and THEN I can see who is calling and maybe answer. If it hasn't gone to VM already. This is really stupid - first and foremost, this thing is a FREAKING PHONE. I should be able to answer a call.
Frustrated. Any ideas/help?
Thanks,
-Dirv
Details
=============
System version: 4.5.629.A956.Verizon.en.US
Android version: 2.3.4
Kernel version: 2.6.32.9-g177d714 mcbk83@il93lnxdroid01 #1
Build number: 4.5.1_57_D2GA-59

I can't hear the outgoing and incoming calls but I can hear the ringer and I was able to call using viber in my iphone 4s 16gb.

I can't hear the outgoing and incoming calls but I can hear the ringer and I was able to call using viber in my iphone 4s 16gb.

Hello sadiepix,
The following article details several things that can be done to quell iTunes' constant need for authorization.
iTunes repeatedly prompts to authorize computer to play iTunes Store purchases
http://support.apple.com/kb/TS1389
Cheers,
Allen

Incoming call problem on iphone 4s

I've had this problem for a couple of days now and couldn't find anybody with the same issue:
My iPhone 4S will interrupt all incoming calls. My phone rings a few times then ends the call.
At my phone the call is left unaswered. On the other phone it says that I've answered, but theres
no voice or anything coming out.
I've tried all the basics:
-Shuttingdown the network
-Booting
-Reinstalling OS
Anything doesn't seem to work.
If you know any tricks or something please tell me.

Problem solved:
It was my operator that didn't work. I've got two sim cards and somehow the other card anwered the calls. Just transferred the calls from the other sim to this one and everything works great again.

Sipura SPA-3000 incoming calls problem

I have a very strange problem with my SPA-3000.
I can make any outgoing calls.
For the incoming calls:
1. I hear the ring
2. Callers do not hear anything (no ringing tones)
3. I pick up the phone and hear nothing
4. Callers still hear nothing and call does not connect
5. I hangup
6. Caller disconnect
What could cause such problems?
I forwarded ports 5060-5061 and 16384-16482 to the adapter.
P.S. I'm using pennytel services.
Thanks.

Matex2 wrote:I already had a STUN server and NAT defined.
I'm really stuck with any other suggestions.
I would run a quick test to see if it involves the determination of your external ip address. Determine your external ip address (run www.whatsmyipaddress.com on a pc attached to the router) and put the ip address on the Sip tab under Ext IP. This is not a permanent solution unless you have a static ip address, but if this solves the problem you know that has something to do with your router. Remove the entry after you run the test.
The basic diagnostic tool available is a sip debug trace. To do this you need a syslog program running on your pc. See this web page for a link to download a syslog program:
http://www.sipura.net/Documents/faq/Section_2.html#9
You setup your pc address under debug server on the SPA3000 system tab, you set the Debug Level to 3 and on the Line tab you set the Debug Option to FULL.
A sip debug trace will show the incoming sip invite, the responses and the startup of the rtp packets.
Message Edited by hw on 08-06-2008 06:30 PM

Q10 INCOMING CALL PROBLEMS

Hi there, I have a Blackberry Q10. All my Incoming Calls do not show the number from where the call is coming from, only "Unidentified Caller" this happens/displays to all my Incoming/Missed Calls. Is there any way I can fix this problem please??? It would be much appreciated

Johan789 wrote:
Hi there, I have a Blackberry Q10. All my Incoming Calls do not show the number from where the call is coming from, only "Unidentified Caller" this happens/displays to all my Incoming/Missed Calls. Is there any way I can fix this problem please??? It would be much appreciated
Johan, open your Phone application.
Swipe down from the top of the bezel to > Settings.
Tap Smart Dialing and set up your correct information in Smart Dialing... national number length, country code, etc.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Lenovo a850 incoming calls problem

Hello.
I have this good phone since 1 month.
Unluckly, since the beginning, i have an annoying problem with incoming calls.
Most of times i'm not reachable and the classical message "THe number you have dialed is busy on another call" is what people calling me normally listen to.
THis happens even if i'm not on another call.
I bought this phone from the most famous chinese shop on line it was already rooted when here.
SOmeone have experienced the same problem?
I have 2 sims.
I have tried to use it with only one or swapping the two. Nothing. Same thing
Any suggestion is appreciated.

Hi,
I have exactly the same problem, from time to time I cannot receive any incoming calls even though network is perfectly fine. The only difference is that it is with lenovo phone model S850.
I have bought the phone for less than two weeks and this problem crops up. I have to say if I knew of this existing problem I would never have bought this phone. From what I have read, this problem seems to be pretty common among lenovo phones (AND ONLY LENOVO PHONES SOMEHOW).
I am extremely disappointed. Why would someone buy a phone when it cannot carry out the very basic requirement of a phone "receiving calls properly". I could have bought a NOKIA for 50 quid and thats it. I wouldnt have to spend 150 quid for a piece of junk.
I also find it very disappointing and unacceptable why the lenovo company has not resolved this imminent and persisting problem depite numerous complaints.
I'm utterly disappointed in Lenovo and will never buy anything related to Lenovo again in the future (unless this problem can be permanently solved).

Why are my Text Contacts and incoming calls only are showing as "Message Received"

All of my text contacts messages just say "Message Received", but if I have set a ringtone for them, that is the ringtone that plays. The same is true of incoming calls, It will show the phone number, but not the assigned name. I don't know everyone's phone number! I barely remember mine!
HELP?? Please ?!
How do I get my caller ID to work properly again?
I have a Galaxy S3
Thanks

Hey there, celtmaidn! Thank you for bringing this matter to the community. I'm sorry that your Caller ID isn't providing you with the details you need, but I'm happy to help. If I understand correctly, incoming calls and messages do not display the name of any of your calls or messages, just the number. Does the same occur on your outbound calls and/or messages? Also, you may have a contact (example: Dave) that you have programmed in your S III with a mobile number, but "Dave" may have a home number as well. Have you confirmed that the number used for that call or message is the same one you have programmed into your device?
DionM_VZW
Follow us on Twitter www.twitter.com/vzwsupport

Canon Rebel T3 EOS Flash and Auto Mode Problems: Help Me!

I recently got a job as a photographer for the nightlife in my city. I went out and tried to shoot the other night. My camera isn't broken, but I had it in auto (green rectangle) and when I'd hit the shutter button, it would just flash, looking like it was having a seizure, and not take the picture. It eventually took the photos, but it flashed in their faces like 3 times before it actually took the photo. People cursed me out and it was awful. Why won't my camera just take the picture the first time??? Why does it say it's "busy" and how do I know when to take the photo to avoid pissing people off? Also, when I went to the "no flash" seting, it took the picture with no problem, but I absolutely NEED the flash to work. Please help me!

Bob has nailed it.... when auto-focus is enabled and the camera is using "One Shot" mode (the default focus mode), the camera will NOT take a photo until it can confirm that it was able to lock focus. To help the camera focus, it will attempt to use the pop-up flash and strobe it very quickly to create something which is more-or-less about 1 seconds worth of continuous light. You'll want an external speedlite flash for two reasons... 1) Several external flash models include a "focus-assist" beam.2) The external speedlite models are significantly more powerful than the built-in pop-up flash and can handle subjects at much greater distances. Normally I'd suggest a Canon Speedlite 430EX II... but Canon recently announced it replacement will be available in mid-septermber. The 430EX III-RT ... and it's the same price (the new model has a radio receiver and can triggered via radio instead of optical (optical triggers require line-of-sight... radio does not.) I'd much rather have the radio-eqiupped version. The focus-assist beam in the flash illuminates a red-pattern momentarily while the camera is focusing. This beam allows the camera to focus even in total darkness. It doesn't have to pulse the flash to work as a modeling light to achieve focus (it's actually much better than the 1-second long burst of light.)

Can´t ear and incoming call that is transfer

Hi I´m using the SPA9000 and SPA400 together with Polycom 301, 501 and 320 phones.
The SPA9000 works great when I transfer an incoming call from SPA400 to the analog FXS ports of the SPA9000 but when I pickup the call and try to transfer the call to an IP phone I can´t ear the person who call although he can ear me.
Other thing I want to know is how to set a pickup group for the incoming call and how to pickup the calls?
Sincerely,
Jose H

Tap the power button once to silence the ringing, twice to send to voicemail.

Telephone numbers and incoming calls

Do I need to have a telephone number in order to receive incoming calls? If not, how would anyone call me? What number would they use?

Hi Sagar,
I don't think you'd be able to monitor calls from a website but you could build a system that monitors calls and submits that data to a site using for example, http.
It's difficult to point you in a direction without more information, specifically about the phone system hardware. Many phone systems come with an api that allows you to interact with it. Which system will you be using?

Incoming calls problem!

HiIs there anyway i can make incoming call open full screen as in Lolipop you just have the small window saying acept or reject and in bright sunlight it hard to seeI am sure I had it open full screen or dialer before but been to call setting and can not find any thing

You would need to use a 3rd party app for that as there isn't an option for this to be changed or modified

Linksys SPA3102 "flashing" and incoming call problem.

Similar Messages

Maybe you are looking for