LINKSYS SRW 2048 bug on the web console ?

Hello,
hope you can help us.
we are experiencing a bug on 2 LINKSYS SRW 2048, that we use since more the 4 years now.
We are currently configuring them for Vmware, we never accessed them trough the console (web gui), but now that we need the switch to be configured (vlan, trunk, ec..) it suddenly reboot every time we enter user and password and press the enter key.
We know that they are pretty old but we just wanted to give it a try...maybe someone of you alreday encountered the same problem.
best regards,
Robi

Dear Lati,
Thank you for reaching Small Business Support Community and for your time and patience regarding your inquiry.
I would first suggest you to reset the switch; unplug it, wait a minute and plug it back in, then try the console connection through hyperterminal as described in the chapter 4 of the admin guide;
http://www.cisco.com/en/US/docs/switches/lan/csbms/srw2048/administration/guide/SRW-US_v10_UG_A-Web.pdf
If the problem persists reset the router once more and try the web-based utility as described by the same admin guide, chapter 5.
If you are still unable to login the device I would then suggest you to contact the Small Business Contact Center for further assistance and please do not hesitate to reach me back if there is anything I may assist you with in the meantime.
https://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
Kind regards,
Jeffrey Rodriguez S. .:|:.:|:.
Cisco Customer Support Engineer
*Please rate the Post so other will know when an answer has been found.

Similar Messages

How do I get the Web Console on top, in FireFox 21 Mac?

In Firefox 21, the Web Developer Web Console seems to be fixed to the bottom with no option to change it. In previous version of FF, there was an option to put it on the top of the window. The bottom is a bad place for the Web Console, especially for Mac users. For one, the status line is right above the command prompt when something is loading or I'm moused-over a link, so I can't type in the prompt. Also annoying as a Mac user, when I bring the mouse too close to the bottom of the window, to type in the console prompt, my dock pops up. Whenever I want to use the console prompt, I have to bring the window up an inch to keep my Mac OS dock from popping up.

I prefer relative inside positioning to a separate window getting in the way. You must assume that I already know what the Web Developer console is to basic extent; it's not a tip to point out an elaborate and separate option that is already known to all who are familiar with the console. Perhaps I didn't explain my problem correctly. I think I meant Web Developer Web Console "above" not "top", but yes "top" to CSS definition of top, including whatever it is called in GUI terms "above", but not like window above or top in layers.

Steps to extend the schema if I have no access to the web console

Hello,
I am usin DS 6.2. The web console is not applicable in my case. So I must extend the schema manually.
I want to add an attribute type and an objectclass. I do have a test server and I did
ldapsearch -L -b "cn=schema" objectclass='*'
and then took what I need:
dn: cn=schema
changetype: add
attributeTypes: ( 1.3.6.1.4.1.42.2.27.9.1.333 NAME 'orclnetdescstring' SYNTAX 1.3.6.1.4.1.1466.115.121.1.40 X-ORIGIN 'user defined' )
objectClasses: ( orclservice-oid NAME 'orclservice' SUP top STRUCTURAL MUST cn MAY orclnetdescstring X-ORIGIN 'user defined' )
When I do:
ldapadd -c -h hostname -p 389 -D "cn=Directory manager" -w password -f myldif
adding new entry cn=schema
ldap_add: Object class violation
I tried to add these lines
attributeTypes: ( 1.3.6.1.4.1.42.2.27.9.1.333 NAME 'orclnetdescstring' SYNTAX 1.3.6.1.4.1.1466.115.121.1.40 X-ORIGIN 'user defined' )
objectClasses: ( orclservice-oid NAME 'orclservice' SUP top STRUCTURAL MUST cn MAY orclnetdescstring X-ORIGIN 'user defined' )
to 99users.ldif and restarted the server. No progress.
any idea please?

You can either use 2 "changetype:modify" operations (not changetype:add since you're trying to modify an existing entry), or you can stop you DS, then edit the 99user.ldif by hand and start it again .

Open the Web Console when a pop-up opens

Suppose I am working with a webpage and I have the console open.
Then, I click in an element, and the javascript code that handles the event decides to open a new window.
That window does not have the console open, so I miss some details of the http traffic, etc.
What I am doing now is to hit Ctrl+Shift+K as fast as I can, or use Fiddler.
But there must be a setting somewhere where I can say "Always open the console when a new window is open", Right?
I googled a bit, but I couldn't not find an answer.

Hi bcartolo,
Not a problem. You can open the Web Console by first going to Tools > Web Developer Tools > Web Console
Then try [https://addons.mozilla.org/en-US/firefox/addon/firegestures/ Firegestures] to customize this.

Why can't the Web console in FF9.01 not see extensions I've added to the Array class (object)?

I've added a number of new methods to the Array object in Javascript. My scripts see them fine, but the Web console reports them as 'undefined'. Apparently the console cannot see my changes. Why is that?

Not the same. It should be like the orange indicator for an imported clip in the camera import window. It's really quite sophisticated in iMovie. When you switch projects the orange line changes to reflect what's in the open project so a clip might have the orange indicator when one project is open in the timeline, and not when another project is open. It's a really useful tool, because it even shows what parts of a clip have been used in the open project.

Security BUG in the web container!

Hello,
I have just accidently discovered a security BUG in the web container. The bug permits you to view the source of the JSP page (welcome page).
To reproduce the bug, do the following:
1. Create a web application. Create new page with name Index.jsp. Add "Index.jsp" into the web.xml as a welcome file.
2. Deploy it under, let's say, "SecurityBugWebApp".
3. Access http://host/SecurityBugWebApp/ or http://host/SecurityBugWebApp/Index.jsp - everything should be as usual - you should see a normal output of a JSP page.
4. Access http://host/SecurityBugWebApp/Index.JSP (notice the case of the ".JSP" ). You should be able to see the source code of the web page. This bug even works if it is under security constraint! This doesn't seem to work, however, with JSPs not listed in the welcome file list.
Sincerely,
Sergei Batiuk.

Peter,
Thank you for your suggestion. This makes sense to
try. I'm actually using a trial license of AS7 with
no updates. I've found update 1 online with free
trial, however, do you know if AS7 update 2 is
available with a trial license and where it might be
located for download?
you can get AS7 update2 Platform edition from here.
Platform ed. is FREE for both development and production deployment
http://wwws.sun.com/software/download/products/3fb01655.html
AS7 update2 Standard Edition can be downloaded from here.
Standard Ed is free only for development, you need to buy a license to use it in production.
http://wwws.sun.com/software/download/products/3f7df408.html
Peter

Unable to login to the web console cisco Prime assurance 9.0 password not working :(

Hi all,
I was able to install the Cisco Prime 9.0 assurance
I am entering the correct username and password still I am not able to login to Web admin page
How do i reset the password and login to the web admin console??
Plz help... urgent...
Rgds,
Rebecca....

Thanks Rob so much
yes i booted the NCS from the DVD and installed the applications
now i have two NCS appliances one is running PI 1.2 and other LMS 4.2

Linksys SRW 2048 constant blinking and slow

Hi all. I tried to search but was not very successful with finding my answer but my problem is that all of the ports are constantly blinking fast. Is this normal?
I have the 2048 switch connected to a linksys wrvs440n router on port 48. Even the non connected ports are blinking dimmly. The internet appear slow as well. If I directly connect a PC to the router (bypass switch) the internet speed is greatly increased.
I am not sure what to look for in the webview. Does anyone have any ideas that I can try?
I even get this constant blinking if only one PC and the router is connected.
THANKS

THanks eepro. The ports that have a pc connected to are blinking constantly which I thought meant a collision was occuring. the other ports are only dimly lit and blinking but I think that just may be the other lights lighting them up from behind the front panel. The problem is even if there is only one pc connected there still seems to be constant blinking on that one port....
The switch just came new from linksys on a warrantee return.
Thanks

Yahoo is no longer loading right due "background" and "font weight" according to the web console but I've cleared the cache and checked the zoom and style settings. What else could suddenly be casuing this issue?

Using Firefox 4.0.1
Get the following errors:
[16:40:58.140] YUI is not defined @ http://www.yahoo.com/:977

Hi,
According to your description, my understanding is that the error occurred when you accessed SharePoint site through form based authentication.
How did you configure the form based authentication?
Here is a link about the steps required to configure FBA in SharePoint 2010 for your reference, and check the steps to see if there anything wrong in your configuration:
http://www.codeproject.com/Articles/352841/How-to-Configure-Form-Based-Authentication-FBA-in
Through the common error message, we cannot find what exactly caused the error.
Here is a similar thread for you to take a look:
http://social.msdn.microsoft.com/Forums/sharepoint/en-US/120ab535-63d2-4205-a51f-1987e9c0cf79/sharepoint-fba-the-content-type-texthtml-charsetutf8-of-the-response-message-does-not-match-the?forum=sharepointgeneralprevious
Best regards.
Thanks
Victoria Xia
TechNet Community Support

In Firefox 30, how can I disable the Web Developer console?

I use a keyboard macro program. Its settings, however, are preempted by the Web Developer tools' shortcuts. Therefore, I either want to (a) totally disable the Web Developer console or (b) remove/reset the shortcuts used by it.

The prefs for disabling some DevTools (devtools.*.enabled) are there on the <b>about:config</b> page, but I'm not seeing anything in the code that they are supported and tests only include a few prefs.
Disabling the developer toolbar works, but not disabling any of the tools in the web console AFAICT.
*http://mxr.mozilla.org/mozilla-release/source/browser/devtools/framework/test/browser_dynamic_tool_enabling.js
I'm not sure if there is a bug about this or needs to be filed?
Why have prefs if they aren't working (I tried it with lockPref as well)?

Workspace studio IDE Vs OSB Web Console

When to use OSB Web Based console and when to use Workbench studio - what are pros and cons - and what is the benefit of one over the other.
Also, which is better in Software Development Life Cycle like building the code and then deploying on the server etc.
Thanks
AB
Edited by: AAB on May 27, 2010 7:43 PM

From a developer perspective we have chosen for the approach of using workshop and deploying locally. We still have a development server to do some more thoroughly testing. But there are some limitations when using a single development server for all your developers, you can for example have only one debug session/connection. More than one person deploying all their code changes (with bugs) directly on one server will not be a very workable situation either.
When you use workshop you have a environment better suited for developers. You can use a code respository to checkin/checkout your project. Editing your message flows is much user friendlier. In the web frontend this is not an easy task. When you edit a flow in the web console you need to do this within a session. When you are developing this does not work very nice. You want to do your changes more quickly and not to be slowed down by this kind of things. The web console to my opinion is better suited for administrators and configurators.
Of course there are some disadvantages to the workshop. For plain development of the services with limited additional requirements to implement concerning security and so on it works. But some more complex configurations can only be done in the web console. For example if you want to add basic authentication to a business service I could only do that in the web console. I currently do not have a list of all these things. But if you look at the editable fields etc. in the web console these are more extensive than in workshop.
Futhermore the workshop is sometimes a little buggy. Copying project and resources does not always work. It crashes sometimes and I even had colluegues that corrupted their project just using the workshop. I have not experienced that yet. So expect to run into some weird unexplainable behaviour once in a while. Restaring workshop or deleting your local server and creating a new one usually fixes a lot of these problems.
Last but not least it is not known (to me) yet what will happen to workshop in the (near) future. It is still supported in the 11g version but I expect oracle will try to get everybody use JDeveloper. So bug fixing in the workshop might be not their number one priority. So it could also mean that workshop will not implement all new features of OSB in the long run forcing people to siwtch to JDeveloper in the end. But that is just a thing I am guessing as I am more of an eclipse fan than a JDeveloper fan ;-) The web console will always be there so if you do not want to invest in learning workshop it is the safest choice. But developing in it and versioning your code in a respository becomes more of a challenge.

Web console doesn't accept login

I am having some problem logging into the web console on one of my Solaris 10 8/07 machines. The web console is online, and showing no errors in any of it's (or the system's) log files. However, when I try to use the root username and password to log in, it tells me the password is not correct. The same root username and password work for logging in at the console. Has anyone seen this problem before?
I have patched the machine with all the latest patches available as of April 16th/08....uname -a shows 127112-11
This machine has N1 System Manager installed on it as well.
Thanks in advance,

It seems as if the console login is working fine. I can log in from both the console and via SSH as root. The problem I am having is that the Sun Java Web Console installed on this machine does not seem to be linked with system authentication ( I can't log in as root, though I can on my other Solaris 10 8/07 boxes ).
The Java Web Console is a standard part of Solaris installation (well, "Entire System" cluster, at least), and is accessed via https://localhost:6789/

How can I get a printable list of the web sites in a tab showing both the name of the site and it's location?

I use tab groups for specific projects and would like to print/save a list of the websites used on each project. Using the list function on a tab group produces a list of the web-sites which can be printed/saved via PrtSc and Word. How can the web-site addresses be included? With this list available I would then close the tabs.

Someone might have created an add-on for this, although I didn't find one in a search.
Could I suggest this workaround for now:
(1) Use the Bookmark All Tabs feature (right-click a tab when your tab group is displayed) to save all tabs to a new folder on the bookmarks menu. Some tips in the "How do I bookmark all of my open tabs?" section of this article: [[How to use bookmarks to save and organize your favorite websites]].
(2) Export bookmarks to an HTML file. Unfortunately, this will be all bookmarks, not just the ones you want, but hang in there. This article has the steps: [[Export Firefox bookmarks to an HTML file to back up or transfer bookmarks]].
(3) Open the exported HTML file in Firefox or your favorite WP program. Now you can either:
(A) Copy/paste the live links for your tab group into your preferred form of archival storage. Or
(B) Print (e.g., select the relevant bookmarks and use the Print Selection feature). However, in order to show the URLs, you need to hack the page a little bit.
(i) In Firefox, you can run a little script in the Web Console on the bookmarks page. Press Ctrl+Shift+k to open the web console. Copy the following line of script, then paste it next to the caret (">") in the web console and press Enter. The URLs should appear after the links.
for(var i=0; i<document.links.length; i++) {document.links[i].parentNode.appendChild(document.createTextNode(' ['+document.links[i].href+']'))}
(ii) In Word, there probably is a macro to split the hyperlink fields into the display text and URL. If Word is your preferred tool, I'll see whether I can write one.

Error in Web Console After UR4

After installing UR4 I now get the following error when opening the web console:
After updating to UR4   know get:
Server Error in '/OperationsManager' Application.
Could not load file or assembly 'Microsoft.EnterpriseManagement.Presentation.Core.Server' or one of its dependencies. The parameter is incorrect. (Exception from HRESULT: 0x80070057 (E_INVALIDARG))
              Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it
originated in the code.
Exception Details: System.IO.FileLoadException: Could not load file or assembly 'Microsoft.EnterpriseManagement.Presentation.Core.Server' or one of its dependencies. The parameter is incorrect. (Exception from HRESULT: 0x80070057 (E_INVALIDARG))
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Assembly Load Trace: The following information can be helpful to determine why the assembly 'Microsoft.EnterpriseManagement.Presentation.Core.Server' could not be loaded.
I am running on windows 2012r2 and sql 2012 both fully up to date on patches and service packs
Not sure if it helped or made it worse but I have tried:
Removing and then adding back the ASP.net IIS features
Did a repair on the web console feature then uninstalled and reinstalled the web console as well.

SOLVED:
Deleted temp files in: C:\Windows\Microsoft.NET\Framework64\v4.0.30319\Temporary ASP.NET Files
IIS reset --- all worked after That.

Web console doesn't use 3rd party security cert

I set up a Mobility Service 2.1 server with a 3rd party public security cert.
The system authenticates through GroupWise 2014, set up via trusted app.
It works fine as far as mobile devices using the cert, but the Web console for the server does not use the same cert.
I've found nothing in the documentation outlining where the security cert for the web console is specified.
Anyone have any idea in what file this is defined?

gathagan wrote:
> I've found nothing in the documentation outlining where the security cert for
> the web console is specified. Anyone have any idea in what file this is
> defined?
Yep -
You can also use the same mobility.pem file that you created earlier for
securing the Web
Admin Console. To do so, do the following:
1. Change to /var/lib/datasync/webadmin on the Mobility Service.
2. Back up the existing server.pem file (cp server.pem server.bak)
3. Copy the mobility.pem file that you created earlier into
/var/lib/datasync/webadmin, and
name it server.pem.
4. Restart the Web Admin (rcdatasync-webadmin restart).
Danita
Novell Knowledge Partner
GroupWise Mobility Service 2.0 Guide - http://bit.ly/1cv13RE
If you find this post helpful and are logged into the web interface,
show your appreciation and click on the star below...
Are you a GroupWise Power Administrator? Join our site at
http://www.caledonia.net/register

LINKSYS SRW 2048 bug on the web console ?

Similar Messages

Maybe you are looking for