Linksys SRW224G4 Fail After Firmware upgrade

Hello Everyone,
I am a newbie in this forum, so please excuse me If I may not make all things right.
I have a serious problem with my Linksys SRW224G4 managed switch.
After the one and only time that I have tried to update its Firmware, a couple of weeks ago,
although that the firmware upgrade ended with a success, When I tried to reboot the switch
the device went broken. Now it does not recieve an IP from the DHCP, hence I cannot see it in a list
with the IP scanner.
I have read and followed the manual, in order to be able to connect to the switch with Hyper Terminal
via an RS232 serial port cable and managed to reach up to the following screenshot.

It's not unrecoverable. It just looks like the existing image didn't take and the boot process wants you to load a new one over the serial link. You're using HyperTerminal, so you already have what's necessary to load the image.
As soon as the switch indicates that it's downloading code using XMODEM, select the file transfer option in the HyperTerminal menu and upload the "SRW2xxG4_FW_1.2.3.0.ros" file using XMODEM. It will take awhile, but should recover the switch.
Also, make absolutely sure that you're using an SRW224G4 revision 1.1. If you upload the firmware from the 1.0 firmware, this sort of thing will happen.
If you happen to have a revision 1.0 switch, you can still recover it via XMODEM, but use the "fesm-12216.ros" firmware instead.

Similar Messages

PC-Suite sync fails after Firmware upgrade of E65

After firmware upgrade of E65 PC-Suite stops syncing Calendar & Contacts from outlook. No error messages, just "0 entries has been updated".
- PC-Suite updated to 7.0.9.2
- Outlook 2003
- XP Prof.
Any ideas?
Solved!
Go to Solution.

The funny thing is - the notes are synced???? If I restore some old contacts they'll double up in outlook, so I think the problem is, that the sync app doesn't see the outlook contact & calendar folder.
Does somebody has an idea?

Crippled 192.168.1.1 page after firmware upgrade

hi,
i recently upgraded the firmware of my WRT160N V2 to 2.0.03.
but since then when i login i get a crippled page on 192.168.1.1 with not even a menu. so i cant even downgrade. is there something i can do?

It is good to know that the issue is resolved
After firmware upgrade it is always recommended to reset and reconfigure the router and I think that is why you were unable to see the menu on the setup page of your router.

T410i SSD user and master password problem after firmware upgrade

Hello.
I have problem with my Corsair Force 3 120GB SSD. After firmware upgrade of SSD my master and user HDD passwords are no longer valid. I'm stuck on BIOS screen and cannot unlock my SSD. After firmware upgrade procedure i got BSOD. Same happened during firmware upgrade on my previous SSD (INTEL X25-M 80GB) but after restart everything was OK. Please help!
Previous firmware version: 1.3
Current firmware version: 1.3.3
SSD connected to another computer shows RAW partition data, but firmware version is 1.3.3 - seems like update was successful.

My X301 Intel x18 got bricked also after a BIOS update then secure erase (was going to sell it). I plugged it to a USB kit and onto a desktop and it was recognised and able to format. But plugging it back to the lenovo it is still a brick. My lucky star there was warranty it was replaced by lenovo.
You may want to try it and extract the data, if it works. And hopefully you can still format it and made it work pluggin back to the lenovo.

Content Copier wont restore after firmware upgrade

I upgraded my N95 8GB to the latest firmware this morning (30.0.018), took 2 complete backups using Contect Copier V4 prior to doing so, but after the upgrade every attempt to restore contacts, settings, etc has failed.
I've tried doing the recommended re-formatting procedure, followed by a restore, which did not help. I've tried restoring individual items only, instead of the whole lot, which also didn't work.
According to the log at the end of the restore, the restore completed successfully. Reality suggests otherwise though.
Could anyone please help?
Thanks,
Adriaan

Right, I've tried using OVI, which did NOT resolve the problem. In fact, it gave identical results to the content copier included with the nseries suite.
I've written to Nokia support who have replied as follows:
"In this instance, allow me to suggest a few workarounds in order to rectify the issue on hand.
First, I suggest that you delete any data not needed from your Nokia N95 8GB to free up the internal memory of your phone before restoring the backed up file. I would like to also suggest that you select the content files that you want to restore to the Nokia N95 8GB. Once you have connected your Nokia N95 8GB to the PC and launched the "Content Copier" application, please select the content file types that you want restored on the phone.
However, if you are still unable to restore the backed up file to your Nokia N95 8GB, there may be inherent issues with your Nokia N95 8GB that may prevent you doing so. In this case, please take your phone to your nearest Nokia Care Point for an assessment. The Nokia Care Point will assess if a repair is required and advise if this may be covered under warranty."
So it looks as if I'm going to have to take it in for repair...

N97 cannot use as modem after firmware upgrade

Hi, sorry if this is a repeat post but driven to distraction.
I use my N97 as a modem to connect to the internet from my laptop when I'm away from home. Since upgrading the firmware I cannot connect through 1 touch access or direct through dial up.
When attempting to connect through 1 touch I get as far as connecting device and then I get the message "Failed to connect device".
I have removed the modem through internet properties and reinstalled PC Suite (after using PC suite cleaner). I am running windows 7 but was connecting through 7 before the firmware upgrade.
Now I'm at a loss. Anyone got any ideas?

Saw another post here that said they make a completely new network with a different name and it worked. I decided to give it a try and it actually did work!!! Don't have any clue why but I don't really care since my network is running again.

Nokia 5800 XM: Problems after firmware upgrade

Hello all,
I upgraded my firmware to V 50.0.005, cause that's what Ovi store told me to do in order to download ovi maps.
However, now, when I open my internet browser it automatically opens full screen which is really not my preference. But when I click "options" it just shuts down.
Also when I enter Ovi store now, at first it seems fine but after loading an app page it crashes saying no more than "Something went wrong".
Thanks in advance for your help.

Hello, I'm afraid I don't have an anser to this, but I too appear to have the same problem. After upgrading to v 50.0.005 I get the following problems relating to web browsing. 1. If I attempt to download anything I get the following error :- Script alert: A critical internal service has failed. after which I click on OK and the browser/application shuts down (and the connection closes). This happens when web browsing e.g. when attempting to download a BBC podcast or using the Ovi Store application to download something. Also it happens whether I'm using my provider's 3G network or a wireless network. 2. If in the browser I click on "options" the browser shuts down. I admit that in order to get Ovi Maps I have previously debranded my phone in order to get the necessary firmware updates, but I haven't had this problem with any of the previous ones. FWIW the Ovi Maps application appears to work well and manage to keep the internet connection up for a long period when online. Does anyone else have this problem? Can anyone suggest anything or will we simply have to hape that the next firmware update comes quickly and cures the problem? Thanks in advance.

Battery life of 15 Minutes after Firmware Upgrade

Now that my system has had the firmware upgrade, I dont get more than about 5 minutes of battery life.
Prior to that I was getting a good 2.5-3 hours ish.
Now, it dies after 5 minutes.
I find it suspicious that this happened immediately after the FMC firmware upgrade.
I understand that the firmware cannot be downgraded easily.
Or is there, please let me know.

Recently my battery on my 15" MacBook started reporting 75% in the OS but the system would shutdown without notice -- also, when I put the computer to sleep (sometimes for only 20 minutes) it would completely lose its charge and shut down.
This started happening after I loaded the new firmware, but I thought it was related to a failing battery, not the FW update… now I’m curious.
I purchased a new "spare" and sent the original one back to Apple for testing. The spare has not had any problems since, but it has only been a few days. I've heard nothing back on the other battery.
I’ll post back if I have any problems with the replacement.

No power after firmware upgrade on nomad jukebox zen xtra

I have the nomad jukebox zen xtra 30gig that froze up over a year ago after i tried to install the firmware upgrade. After the unsuccessful attempt, the mp3 player stopped working.... I mean no power at all. I've changed the battery and recharged the battery from an outside source...still no luck. I can't even try any of the suggestions anyone gives on this site because I have no power.Does anyone have this problem? More important, does anyone have this problem and know of a solution?I've already set my pc back to wmp 0, I have the firmware on the desktop waiting. Now all I need is some power on this unit so that i can try some of the suggestions that seems to be working for people. Thank you

I have the same problem too, but my unit is a?Creative Normad Junebox Zen Xtra 40GB. I was trying to find a solution to my problem when I read about your problem. I have pressed the reset button, on / off switch, removed the battery, reinstalled the battery, and nothing seems to work. I was hoping you?might get a solution to this problem, so that I might be able to fix my MP3 player. If I hear of a solution, I will let you know, thanks for sharing. Issue:? While updating the firmware to the Zen Xtra 40 GB, the unit powered down and?has never came on again. There seems to be no real reason why the unit should not power up. The battery and the AC adapter are working correctly. I am very disappointed in Creative...

No contacs after firmware upgrade on N70

Hi
I did a firmware upgrade yesterday on my N70 using NSU. Of course I did a backup using the uptodate Nokia PC suite. After the firmware upgrade I saved the data back to the phone aagin using the Nokia PC suite. Everything looks good except that no contacts are there.
I did the upgrade again just to make sure that everything went OK with the same result.
Can some help or has the same problem?
Firmware V 5.0638.3.0.1 18-09-06 RM-84
PC Windows XP SP2
Nokia PC Suite 6.82.22.0
NSU 1.2.0en
Best regards
Chris

not sure about your PC Suite version but this has been well documented in these forums and I had the same problem and with N70. I think it was mentioned as a PC Suite issue, or a combined PC Suite issue N70 issue with many people reporting it. Anyway nothing you can do but enter your contacts or transfer from another phone

HP Laserjet p1102w - after firmware upgrade / Smart Install update - down to 1MB free memory

Hello,
I have a Laserjet p1102w running off a laptop with Windows 7 64-bit. Just bought the printer this month.
After updating the firmware to 20120814 version and updating the SmartInstall update utility for the 20120814 version as well, I am now down to 1 MB free memory (out of 8MB originally). [Another LJ p1102w updated prior to these updates has 3MB free memory.]
Because I have 1MB free memory, the printer is almost a brick. It can print simple text based pages - however, printing any page with a graphic or a PDF file will cause the printer to take forever to receive data - essentially preventing printing a page on my new printer (while printing the same page instantaneously on my older nonupdated p1102w).
Is there any way to fix this problem, given there is no memory upgrade option? Otherwise, this printer is a brick.
Thank you in advance for a reply - especially from HP.

Hi cyskim,
Did you tried turning the printer off and on after updating the firmware? This should clear its memory, including any memory may affected during the firmware upgrade proccess .
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

HP 5524 Wireless does not work after firmware upgrade

HI,
I have just purchased an HP5524. After initial problems setting up the WPA key from the printer screen, I connected via USB, found the printer and swapped to wireless successfuly. I then installed the printer software on all my computers at home successfully over wireless.
The printer then needed a firmware upgrade to support eprint (?), which is successfully connected, downloaded the fireware, installed and went through the boot cycles successfully.
However, ever since wireless will not work. Before I return it to the retailer as "not fit for purpose" I thought I would ask the forum. The diagnostics downloaded a tool, which I went through, but this did not offer solutions that I had not already tried.
Thank you

Hi,
Thank you for posting you query,
In order to resolve the issue, please make sure the printer is placed closer to the router and uninstall the printer drivers already installed and then start the instalaltion and seelct teh connection type as wireless network. Then select use USB to configure wireless and when prompted conenct the USB cable and then select the network and enter the encryption key follow the onscreen instructions.
If the issue still persisits, please open the browser and in the address bar enter the IP address of the router and click on GO. This will take you to the router configuration page. On the router page, please click on Wireless Setup and please make sure SSID Broadcast is enabeld and the Wireless Mode is set to Mixed or 802.11 B/G/N and the Wireless Channel is set to 11 and click on Apply. Then try to connect the printer to the network by using the CD.
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"
(Although I am employed by HP, I am speaking for myself and not for HP)

Fans And Voume after FirmWare Upgrade

Hey there!
I have two very positive pieces of information, some repeated:
1) The volume of my speakers and "line out" was weak at best prior to the FirmWare upgrade. Now, it is positively explosive! I mean, the volume control works just like I would have expected. Perfect...
2) The fans are coming on more consitantly. I can actually hear them now, which makes me wonder... The temp on the Hard Drive has not gone above 92 since I upgrade the firmware (not that I have noticed however).
Bob

Hi Bob!
What did you use to check the temperature?
I installed the 10.4.6 and the firmware, and now I could cook an egg on the keyboard. I didn't have the heat problem before, now after the updates, I am fried (literally).
Gus

Iomega Storcenter ix4-300d stuck at 95% after firmware upgrade

Hi,
I upgraded my device after I got an email that there is a new firmware:
An update to version 3.2.10.30101 of the Iomega StorCenter ix4-200d software is now available
I installed the update but now it is stuck at 95% after rebooting.
Never had any problem before the firmware upgrade.
Any advice?

Hello BelgianTomas
I recommend that you first power down the unit if the unit has not completed the boot process. Then re-seat all disks and try booting the unit again. Please do not try to access the web interface until the power led is solid white.
Next would be to try moving the internal disks to different bays to see if a different drive order wil allow the unit to boot.
If that does not help, LenovoEMC suppor should be contacted for more advanced options.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Udisks inhibiting fails after system upgrade

Hi,
To keep my cdrom silent I have in rc.local this line:
udisks --inhibit-all-polling &
It worked fine, but stopped working after yesterdays upgrade
Now it (in console) returns:
Inhibit all polling failed: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken.
And in kernel.log I found this:
May 29 20:58:27 Mypc2 kernel: [ 2160.206487] INFO: task udisks-daemon:2105 blocked for more than 120 seconds.
May 29 20:58:27 Mypc2 kernel: [ 2160.206491] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
May 29 20:58:27 Mypc2 kernel: [ 2160.206494] udisks-daemon D c109b5e5 0 2105 1 0x00000000
May 29 20:58:27 Mypc2 kernel: [ 2160.206500] f4b29d8c 00000086 f4b29d04 c109b5e5 00000001 00000000 f4a9f980 f533de00
May 29 20:58:27 Mypc2 kernel: [ 2160.206507] f2748400 f533de00 f4b29d14 c127164f 000000c3 f6006380 c14c4380 f4a9f8c0
May 29 20:58:27 Mypc2 kernel: [ 2160.206514] f4a9fa84 f533de48 f533dfd4 c14c4380 f6006380 f4a9f8c0 c142df60 00000000
May 29 20:58:27 Mypc2 kernel: [ 2160.206521] Call Trace:
May 29 20:58:27 Mypc2 kernel: [ 2160.206531] [<c109b5e5>] ? __rcu_read_unlock+0x185/0x190
May 29 20:58:27 Mypc2 kernel: [ 2160.206536] [<c127164f>] ? sock_def_readable+0x5f/0x70
May 29 20:58:27 Mypc2 kernel: [ 2160.206541] [<c11a3a42>] ? kobject_get+0x12/0x20
May 29 20:58:27 Mypc2 kernel: [ 2160.206546] [<c1195a8f>] ? get_disk+0x6f/0x120
May 29 20:58:27 Mypc2 kernel: [ 2160.206552] [<c131ad9d>] __mutex_lock_slowpath+0x10d/0x2b0
May 29 20:58:27 Mypc2 kernel: [ 2160.206556] [<c131af4b>] mutex_lock+0xb/0x20
May 29 20:58:27 Mypc2 kernel: [ 2160.206560] [<c1131447>] __blkdev_get+0x47/0x320
May 29 20:58:27 Mypc2 kernel: [ 2160.206564] [<c1131762>] blkdev_get+0x42/0x290
May 29 20:58:27 Mypc2 kernel: [ 2160.206567] [<c11319fe>] blkdev_open+0x4e/0x70
May 29 20:58:27 Mypc2 kernel: [ 2160.206572] [<c1102e36>] __dentry_open+0xe6/0x300
May 29 20:58:27 Mypc2 kernel: [ 2160.206576] [<c1104186>] nameidata_to_filp+0x66/0x80
May 29 20:58:27 Mypc2 kernel: [ 2160.206579] [<c11319b0>] ? blkdev_open+0x0/0x70
May 29 20:58:27 Mypc2 kernel: [ 2160.206584] [<c111124f>] finish_open+0xaf/0x1a0
May 29 20:58:27 Mypc2 kernel: [ 2160.206587] [<c1110043>] ? do_path_lookup+0x53/0xe0
May 29 20:58:27 Mypc2 kernel: [ 2160.206591] [<c1111838>] do_filp_open+0x1d8/0x6a0
May 29 20:58:27 Mypc2 kernel: [ 2160.206595] [<c11affff>] ? kstrtoll+0xf/0x80
May 29 20:58:27 Mypc2 kernel: [ 2160.206600] [<c115ac27>] ? sysfs_release+0x77/0x90
May 29 20:58:27 Mypc2 kernel: [ 2160.206604] [<c11041f5>] do_sys_open+0x55/0xf0
May 29 20:58:27 Mypc2 kernel: [ 2160.206608] [<c1103569>] ? filp_close+0x49/0x70
May 29 20:58:27 Mypc2 kernel: [ 2160.206611] [<c11042b9>] sys_open+0x29/0x40
May 29 20:58:27 Mypc2 kernel: [ 2160.206615] [<c10037df>] sysenter_do_call+0x12/0x28
I looked at packages that were upgraded yesterday, and here are few that can be relevant to this issue:
[2011-05-28 22:48] upgraded udev (167-2 -> 171-1)
[2011-05-28 22:49] upgraded udisks (1.0.3-2 -> 1.0.3-3)
[2011-05-28 22:51] upgraded kernel26 (2.6.38.6-1 -> 2.6.38.7-1)
[2011-05-28 22:51] upgraded kernel26-headers (2.6.38.6-1 -> 2.6.38.7-1)
[2011-05-28 22:52] upgraded udev-compat (167-2 -> 171-1)
So what might be wrong? Any ideas?
Thanks

What if you disable polling of a specific device with " udisks --inhibit-polling /dev/the_devicename & " ? So without 'all', and using the_devicename that "ps aux | grep udisks-daemon" shows?
And have you tried using and udev rule instead of a line in rc.local? For example I use this to disable polling a card reader:
# /etc/udev/rules.d/02-udev-disable-cardreader-polling.rules
SUBSYSTEM=="block", ENV{ID_VENDOR}=="APPLE*", ENV{ID_MODEL}=="SD Card Reader*", ENV{UDISKS_DISABLE_POLLING}="1"

Linksys SRW224G4 Fail After Firmware upgrade

Similar Messages

Maybe you are looking for