Linksys SRW224G4 firmware upgrade fail!!!

Hi,
I have a switch SRW224G4 from Linksys and doesn't work now after an firmware upgrade!
If is possible, I need that switch so a rapid answer will be appreciated!
Simple, here the result when I try to install the firmware "ls_106-12216.ros" or "SRW224G4P_SRW248G4P_image_v1020.bix" that came from your web site!
Here the result for "ls_106-12216.ros"
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>>>
Writing to flash 0x32d980 records...
Setting checksum: 0x19527ef1 , Address: 0x0
OK.
Flash programming success.
Perform WARM BOOT ...
------ Performing the Power-On Self Test (POST) ------
UART Channel Loopback Test........................PASS
Testing the System SDRAM..........................PASS
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.0.06 Built 23-May-2005 16:58:25
Linksys SmartSwitch based on 88E6218 with ARM946E-S.
32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
FAIL !!! Check image for valid file.
Please download a new image.
Here the result for
Downloading code using XMODEM.
-- Download complete --
Wrong file format. Writing aborted.
Perform WARM BOOT ...
Thanks,
Steve

I just tried updating the firmware in my SRW224G4 using the file "fesm-12216.ros" as indicated based on my bootloader version 1.0.0.06.
Now it's stuck in a reboot loop. Here is the log from Hyperterminal starting from the update:
Startup Menu
[1] Download Software
[2] Erase Flash File
[3] Password Recovery Procedure
[4] Enter Diagnostic Mode
[5] Set Terminal Baud-Rate
[6] Back
Enter your choice or press 'ESC' to exit:
Downloading code using XMODEM.
-- Download complete --
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>
Writing to flash 0x2e4180 records...
Setting checksum: 0x1709abda , Address: 0x0
OK.
Flash programming success.
Perform WARM BOOT ...
------ Performing the Power-On Self Test (POST) ------
UART Channel Loopback Test........................PASS
Testing the System SDRAM..........................PASS
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.0.06 Built 23-May-2005 16:58:25
Linksys SmartSwitch based on 88E6218 with ARM946E-S.
32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
Decompressing SW from flash
100%
OK
Running from RAM...
*** Running SW Ver. 1.2.2a Date 05-Apr-2007 Time 15:35:50 ***
HW version is 00.00.02
Base Mac address is: 00:12:17:5d:08:d5
Dram size is : 32M bytes
Dram first block size is : 16969K bytes
Dram first PTR is : 0xF6D840
Flash size is: 8M
01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading startup configuration.
01-Jan-2000 01:01:08 %ERHG-F-SEND: BOXP_perform_smi_scan_of_devices_in_slot: inv
alid device type is found: 268374443 on device 0
***** FATAL ERROR *****
Reporting Task: ROOT.
Software Version: 1.2.2a (date 05-Apr-2007 time 15:35:50)
***************** SYSTEM RESET *****************
It just repeats this over and over. The unit is out of warranty. Can I do anything to get this switch back up and running?
Should I try reloading the firmware again or updating the bootloader?
Any help would be most appreciated!
Thanks.

Similar Messages

Linksys e4200v2 firmware upgrade fails -bad file

I'm trying to upgrade my frmware to the lastest one (classic firmware)
I've downloaded this file multiple times http://homedownloads.cisco.com/downloads/firmware/1224693043651/FW_E4200_2.0.37.131047.zip
When I try the firmware upgrade (manual upgrade) and select the file, it always complains about the file being corrupt (using the .ssa file in the zip).
How can I solve this issue?
Kind Regards, Jurgen

Hi, I’ve noticed that all smart routers’ classic firmware starting from E4200 v2 to EA4500 contains .ssa as the file extension. So, the moment you load a firmware with that file extension then the router should automatically read it. What you can do is to use other browsers or better yet use another computer just to isolate the problem. If that will not work then try the following:
Download the tftp utility (select version 4)
Disconnect the modem from the router and just have the computer connected to the router's ethernet port
Assign a static ip address on your computer
Lower the speed of the computer's LAN card to 10 half duplex
disable any firewall or anti-virus software on your computer
Run the tftp utiilty

Firmware upgrade failed, printer now say i has firmware version 0. attention light lights up

Hey all
I had a problem printing a pdf on my mac, and then tried to upgrade my mac driver and printer firmware.
But the firmware upgrade failed for some unknown reason. And now the printer just have the ready and attentions lights on constantly.
I have tried to restart and reset the printer many times, and tried the HP firmware upgrade utility several times, with no luck. It just say it was "failed to upgrade"
Any idea what to do ??
My printer is a HP Laserjet Pro CP1025nw
Thanks
Jan

Hello Jan
It definitely sounds like the firmware update failed. Firmware is like a devices Operating System. Without it, it can't do much. This is backed by the "failed" message and that your printer reports it has version 0.
The printer will need to be serviced. Please call HP Phone Support at 1-800-474-6836.
Don't forgot to say thanks by giving "Kudos" to those that help solve your problems.
When a solution is found please mark the post that solves your issue.

Creative Zen Microphoto - "Firmware upgrade failed&qu

Hi,
two days ago my Zen Microphoto started in "Recovery Mode".
I had no means of getting out. I first selected "Clean Up" and rebooted, still "Recovery Mode".
Then I downloaded the latest firmware version for it:
ZENMicroPhoto_PCFW_L6__3_0.exe
Then I selected "Upgrade Firmware", acknowledged with "Yes", the firmware was deleted, but the windows firmware application said "no player connected" after connecting the player.
Okay, after googling a bit, I found out that I needed to downgrade from WMP to WMP 0.
I (painfully) did this and after installing an additional Registry Key via fixup.cmd the
ZENMicroPhoto_PCFW_L6__3_0.exe
detected the player (hurray!). It showed "Current Player Firmware Version .20.0 " and "Upgrade File Version .3.0".
When clicking on "Upgrade" at the windows application, the blue progress bar appeared and the player showed "Recovery Mode" and a blinking USB logo.
What it did NOT show afterwards was a gear symbol with "Upgrading firmware" (which I found on a screenshot in the internet).
When the blue progress bar of the windows firmware upgrade application reached about 85% it halted and after minute the windows firmware application showed "Firmware upgrade failed!" while the player only showed a black screen with "Recovery Mode" and the green battery symbol at the top.
I also tried the same procedure with
ZenMicroPhotoP4S_PCFW_LB__20_0.exe with the same result: "Firmware upgrade failed!"
Any ideas how to "repair" the player
Toddl
Message Edited by Toddl on 04-2-2008 09:40 AM

I have this same problem except with the Zen Vision: M. Any help would be appreciated.

Firmware upgrade fails

I am having trouble upgrading the firmware on my WRE54G. My hardware is v.3 and the existing firmware is 3.01.01.
I downloaded the latest firmware and extracted the .img file. I went to the admin page of the expander, pointed it towards the new firmware, and hit "go." After a minute or so it said something like:
Firmware upgrade fail.
Fail!
No reasons are given.
Anybody have any idea what is going on?
Thanks,
Garth

I had a similar problem upgrading firmware with my WRT300N. What i did to solve the problem was first i downloaded and went through the winzip program given for the router, then i went back to the webpage of the router and retried the upgrade and it worked. I actually ignored by routers version, and downloaded and went through each winzip program and each firmware upgrade for every different version . **i only downloaded the firmware up to my version and my version**.
Message Edited by DaveY on 11-15-2007 07:01 PM

Vision:M - "Firmware upgrade failed!&qu

After spending several long, long hours rolling back WMP, trying different USB ports, installing and uninstalling various software, and borrowing friends' computers, I FINALLY got the firmware upgrade software to recognize my mp3 player. With great delight and an intense feeling of satisfaction, I clicked the "Upgrade" button and waited for several minutes, only to get a "Firmware upgrade failed!" message. I've tried the "Reload Firmware" option more than once, only to receive the very discouraging "Harddisk Problem". I've tried everything I can think of, from formatting to rebooting to resetting to reloading, but to no avail. I'm now left, like so many others, with a $300 bookend. Now what? I'm completely demoralized.

Well, being the stubborn person that I am,?I didn't listen to your advice andYesterday, against all odds from what I read on this forum, and being told that I would end up with an expensi've paperweight,? I decided to take the plunge and upgrade my Zen Vision M 30MB. ?I downloaded the newest firmware .6, saved it on my laptop which runs WMP 0, disabled all applications, including Norton and virus and spyware programs, as well as Creative's detector, connected my Zen Vision M to the USB dri've, double clicked the new firmware file, and followed the instructions. The new firmware started installing, within 3 minutes my player rebooted and then the library started rebuilding and within 5 minutes the process was SUCCESSFULLY COMPLETED!!!!!My player is working better than ever, it has all the new upgrades, album art, never went into Recovery Mode, and most important of all, I didn't lose any of my 2500 songs, hundreds of photos, slideshows and numerous videos, even my personal wallpaper and themes remained the same. I subsequently took the player to my desktop which runs WMP to test it'sand lo and behold, my player was immediately recognized, i transferred music and pictures without any problem and my player is now drag and drop compliant ?through Windows Explorer. My faith in Creative is unfaltering, I also own a MUVO TX FM, a Zen Micro and a Zen Sleek Photo and never had any problem with any of them.

WRK54G firmware upgrade fails: file pattern error.

When I attempt to upgrade the firmware in my WRK54G router, the upgrade fails with this error message:
Upgrade action is not finish!!
Upgrade file pattern error.
The linksys download page says the file size is 1.10 MB.
The size of the file I downloaded (WRK54Gv2_1_00_1) is also 1.10 MB (1,160,036 bytes). So it appears the file was downloaded successfully.
I had no problem upgrading the firmware to version 1.1.
Please advise.
Thank you

What is the hardware version of your router? Is it version 1, version 1.1 or version 2? Where did you download the firmware of your router? Is it from the US website.
On the US website you have 3 wrk54g, one is version 1, version 1.1 and v2.
"When love and skill work together, expect a masterpiece."

WRT350N- Firmware Upgrade Failed

when upgrading with .bin file (v1.05.8) via Administration - Firmware Upgrade, it fails when status showing 76% completion.
Please help what i need to do?
I already tried to boot in safe-mode to minimize programs running (firewall, etc), still showing Upgrade failed.
/v
Message Edited by viva on 10-20-2007 06:56 AM
(Edited subject to keep threads from stretching.
Thanks!)
Message Edited by JOHNDOE_06 on 10-20-2007 06:59 AM

Go to the control panel/network connections and right click on the local area connection. Click properties and roll down to highlight Internet protocol TCP/IP. Click the properties button and check "use the following IP address". Fill in 192.168.1.5 and tab through. The subnet mask will fill itself out to 255.255.255.0
make the preferred DNS server 192.168.1.1 (the router) and click okay.
If the computer succeeds in getting an IP address (verify this by opening a command window and typing "ipconfig" and seeing what it say under the local area connection), type ping 192.168.1.1 in the same command window and see if the router responds.
If so, you can use the TFTP.exe utility from linksys, available from linksysinfo.org at
http://www.linksysinfo.org/forums/downloads.php?do=file&id=4
Run this program, point it at the router IP 192.168.1.1 and show it the bin file you want to use. Might be a good time to use the released firmware rather than a beta. But that is your call. You can get the latest firmware from the linksys page.
If you are unable to ping the router, try putting the ethernet cable in a different port. Don't ask me why, but when my router bricked, it would only work on slot 4. Found this out by accident, but I was able to fix the router when I did this. If it does not work on any slot, you may be screwed. Call linksys and ask for a RMA to get a replacement. I would not tell them you bricked it with a beta firmware!

SGE2010P 48port Gigabit POE Firmware Upgrade fails

I have a Linksys SGE2010P 48 Port switch with POE and I cannot get the firmware to upgrade.
I have downloaded the firmware software from the site: http://www.cisco.com/en/US/products/ps9985/index.html
Everytime I run the EasyUpgrade application I get the error after it starts the Telnet session:
"Did not find device information. Application will terminate"
I cannot find any reason why this is happening. I know that I have a SGE2010P and I know that I am downloading the correct firmware.
Am I missing something?

I am having the same issue where the "Easy upgrade" utility fails. When I try to upgrade firmware via the Web GUI, I am able to upload the "Software Image" & when I click "Done" the Firmware Upgrade screen displays again without any status and/or notifications relating to the firmware that was just "successfully" uploaded (according to the screen at least).
I was able to successfully upgrade the Boot Version from : 2.0.0.00 to 2.0.0.03 with this same process so what is going on with the Firmware update?
It is as if the Firmware is uploading to the switch but the update is not running.
Help!

Linksys SRW224G4 FIRMWARE UPDATE

Hi, i want to update firmware to a Linksys SRW224G4 switch.
My switch model and version are:
Serial Number
Model Name
SRW224G4
Hardware Version
00.03.00
Boot Version
1.0.2
Firmware Version
1.2.1b
I try update firmware via http, but nothing occurs. I download firmware version 1.2.3 (latest)
I try TFTP with the same result.
I get no messages, no error, no logs, nothing.
I`m using VLAN, and trying update from a notebook conected to a managed port.
I try reboot, turn it off and on, but firmware don`t update.
What I`m doing wrong?
Where can I found a manual step by step to update Linksys Switch?
I have three of them and I want to be most update possible.

Can some one please help....
I have exactly same problem
We have a SRW224G4 V1.1 Switch.
Serial Number
Model Name
SRW224G4
Hardware Version
00.03.00
Boot Version
1.0.2
Firmware Version
1.2.1b
On the Front of the Switch it say SRW224G4 v1.1
Is it possible to upgrade to Firmware version 1.3.2.0. ... because I can't get it to load this firmware.
I'm doing it via HTTP upgrade and when it restarts after upgrading, it returns to the current Version 1.2.1.b again.
Have I misunderstood something???
Firmware file is 1.3.2.0.ros
And I have done like discribed i the following link:
http://www.cisco.com/en/US/products/ps9967/products_qanda_item09186a0080a36480.shtml
Release Notes attached as PDF File and user guide
Is it possible to contact Cisco direct by mail about this????

Spa508 firmware upgrade failed

I bought a spa500ds and need to upgrade the firmware on my 508G to use it.
When I try to upgrade to 7.5.4, or 7.5.3 I get a failure. I was able to upgrade to 7.5.1a fine. All firmware was downloaded from cisco this morning and unziped
I see my tftp server giving the file.
I get upgrade failed: 12. corrupt file in my syslog
Any idea where to look next?

It states on the release notes of 7.5.4, that upgrading from 7.5.1a you should first upgrade the phone to 7.5.2b.
Have you done this upgrade step?
Joao

WRT54GS V.4 Firmware upgrade failed.

Hi,
I need help on the unit on the firmware upgrade.
Info:
Device Model No.: WRT54GS v.4
Webpage firmware Version: v1.06.3
I had download the Version 4 firmware and upgrade fail.
Please help!!!!
Thanks

Are you getting any specific error..?
Which browser you are using...?
Are you upgrading the router's firmware from wireless computer...?
Use the hard-wired computer (connected to the router) and try to use Internet Explorer to upgrade the router's firmware and check.

SRW224G4 firmware upgrade

Hi I have questionS:
1. Can I upgrade SRW224G4 in web browser from 1.2.1b to 1.2.2b boot version 1.0.2?
2. After firmware upgrade will be in switch the same configuration or default?
Thank you.

Hi,
The upgrade should work fine from a browser, i recently upgraded one of my switches.
Configuration should remain the same after the upgrade.
However, SRW series tend to have some problems, so:
- backup your configuration before upgrade (it's best practice to always backup all configs before any upgrade on any switch)
- have a serial console ready with Xmodem software, in case the upgrade goes bad...
Cheers,
Tamas

Portege R400 - Firmware upgrade fails for 3G card

During the Firmwareupgrade of the embedded 3G Card(Expedite EU870D) in my Protege R400 I have a power fail. On next start I can't countinue with the upgrade. The Card don't work anymore.
The Modem and the COM Ports I can't see in the Device Manger. Is there a solution for that Mistake? Thanks for help!
Pumbkin

Why you do the firmware update?
You should do this only if the Vodafone SIM card is not working properly!
I found this info which pop ups before running a firmware upgrade!
+Cautions in the FW Update:+
+Please be sure to read this carefully before upgrading the FW.+
+1. FW Upgrade is not needed when Vodafone SIM card is working properly under customers environment. Run the FW upgrade only when Vodafone SIM card is not detected. Please note that the FW is no longer revertible to the prior state once upgraded.+
+2. This upgrade tool is applicable for the following models with built-in 3G module:+
+ Portege R400+
+ Portege R500+
+ Tecra M9+
+3. Please exit 3G communication and close the Connection Utility before running the FW upgrade.+
+4. Close all the applications before running the FW upgrade. Please DO NOT launch any application during the upgrade process.+
+5. Please make sure to use an AC adaptor to power the computer during the FW upgrade process. Power failure during the upgrade process may lead to 3G modem failures.+
+6. Please DO NOT Suspend/Hibernation/Shut Down the computer during the FW upgrade process. Doing so may lead to 3G mode+
So please firstly these points before you would try to upgrade the firmware!

Zen Micro 5GB Firmware "Upgrade Faile

Zen MicroFirmware: 2..02?Have just bought it from america, have tried installing both firmwares from the site, and both of them say "Upgrade Failed!" I havent installed any of the software from the disc except the Zen Micro driver, my pc didnt need this but i thought it would be best to. Also i can only add tracks to it through WMP 0, i cant drap and drop in windows explorer, why is this? On my old creative muvo n200 i could do this fine!?Some help please. Do i need to erase the firware in the recovery menu? I am just running the downloaded applications when my player has the docked icon on the screen.
Message Edited by ajay6 on 03-5-200607:28 PM

Thanks for help.
Major problem solved.
Already upgraded to new firmware.
I do it by:
1. uninstall all creative application and plugin.
2. using registry cleaner to clean the registry.
3. downgrade WMP to WMP0
4. Detected by WMP as MTP device, loading firmware upgrade, closed WMP. upgraded.
Now it Working fine already, just still have some problem is:
. Only WMP can detect it, all creative application can't detect it..
thanks anyway.

Linksys SRW224G4 firmware upgrade fail!!!

Similar Messages

Maybe you are looking for