Linksys vs. extreme

I am going to be buying a linksys router this weekend, but i have been looking at the airport extreme quite a bit today. i have seen where a lot of people are saying that linksys drops the connection alot, etc. i am sure AE isn't without its problems also, but would like to go all apple for compatability.
we currently have an imac, not configured for wireless and probably will never be wireless, and today just received an ibook. i want to be able to use the ibook all over the house ( 2 story).
What cables do i need to get w/ the airport extreme? is anything included?
i don't have an apple store or reseller anywhere near me to go out and buy one today, may order one over the internet. thanks for the help
deb  
imac g4 [10.3.9], ibook   Mac OS X (10.3.9)   fuji camera, hp psc 2210

Deb,
Either the Linksys or the AEBs will fit your needs. The AEBS comes with all the necessary wiring, as does the Linksys. You are aware that your modem must be equipped with an ethernet output for either router, or you will not be able to network your computers to share an single ISP connection (usb modems will not work). Furthermore, if you are using a dial-up connection, you must use the AEBS.

Similar Messages

  • Toshiba 4015 , Linksys wpc11 , Extreme Base Station cannot connect! Help

    I have one IP address coming into a wired router(linksys bsr41), The router has two good ports. I go directly from one port to a homemade pc and to the airport extreme base station with the second. I have a mac mini wired to the port on the base station. I use imac g5 wirelessly with no problems.
    I am trying to set up a Toshiba 4015 CDS to use wirelessly on my deck and I am having a lot of trouble. The Toshiba is upgraded to win 2000 and has 160 meg Ram. I am attempting to connect to the base station with a link sys wpc 11 wireless - b card. I have tried to change numerous setting on the base station but with no luck. I have power to the card but no link. I have used the linksys utility and it can't see the aebs and have tried a 3rd party utility recommended by linksys(freescape????) but it cannot see the base station either. Any suggestions would be greatly appreciated.
    I connect through dsl. Thanks, Mike

    When I connect cable to the lan port , I cannot connect with dhcp or with dhcp disabled.
    I tried both... restarting aebs and imac wireless and could not connect. When I disable dhcp I am forced to enter manual settings and I am not sure I have correct Ip address since it is behind my router. My internet provider said my base station would have to be behind the router because of a cloned ip address. I am not quite sure what that means. Thanks again for the help.....I have a xmas party to go to but will try further recommendations when I get home.

  • How do I make an Airport Extreme work with a Linksys WRT160N

    I have a Linksys WRT160N V3 Router that I have connected to my cable modem. I have an iMac in another room along with a PC based laptop. Range is fine to get them to connect wirelessly. However what I would like to do is to also connect my Blu-Ray device to the internet. However it isn't wireless. I was told I could use an Airport Extreme to bridge to my WRT160N. What I want to do is hardwire connect my Blu-Ray player and perhaps my iMac to the Airport Extreme using my WRT160n's access to the cable modem. Basically I'm trying to make to wirelss routers talk to each other. I can't seem to make the Airport Extreme work. Any assistance would be great.
    Thanks,
    Tim

    Welcome to the discussions, Gonzotoo!
    +I was told I could use an Airport Extreme to bridge to my WRT160N+
    Unfortunately, this is not correct. The AirPort Extreme does not have the capability that you need. If you could connect the Linksys and Extreme together using an ethernet cable, it would function as you wish. Or, if it's not possible to connect them using an ethernet cable, you might take a look at a pair of ethernet powerline adapters to accomplish the same task by using the AC wiring in your home.

  • Disappointed CISCO-LINKSYS ~~~ after-sales support of E4200V1 ~~

    Hi guys,
    I'd like to express my feeling of purchased E4200V1.
    I bought E4200V1 around 1 yr. Before that , I was considering E4200V1 (just has HW ver.1)  and  ASUS - RTN56U.
    Finally, I voted CISCO-LINKSYS.
    Hoewever, CISCO Development team does not keep the improvement of their product and they trend to release E4200V2.
    In contrast to ASUS,, their R&D pay their heart to customer to keep improvment of thier products
    http://usa.asus.com/Networks/Wireless_Routers/RTN56U/#download   Their firmware is keeping update.
    In E4200V1, even many victims (who chose E4200V1) compliant the firmware.
    But CISCO -LINKSYS seems like do not care.............
    Hey guy, will you select CISCO - LINKSYS series products next time ?  To me, absolutely not !
    koklee

    I have the same router as well. I agree with you. Cisco/Linksys are extremely slow on the firmware front to fix bugs and make new enhancements. I have suggested a traffic meter many times to monitor daily/weekly/monthly bandwidth. That alone is pretty standard on all new routers. Yet Cisco/Linksys still does not have one today. Even with the lateast EA4500.

  • Advanced? Network Setup Help

    Hi All,
    I revisited my network problems (posted earlier) and everything is now working peachy.
    My current setup:
    cable modem -> airport extreme -> wireless computers
    (wan) | ---> linksys router ---> VOIP
    |--> Buffalo Linkstation
    |--> wired computer
    Ok. If I plugin to the linksys router I can see the Buffalo Linkstation (which is a shared NAS drive).
    I can't however see the Buffalo via wireless. I am positive this is due to my configuration of the network - I DHCP (10.1.X.X) w/ the Airport Extreme and DHCP (192.168.X.X) with the Linksys. While technical, I don't mess with network configuration very often.
    My question - what can I do to set it up so that the wireless computers can see computers / NAS drives on a plugged in router? The configuration is changeable btw (ie cable modem -> linksys -> airport extreme) if necessary.
    Thanks for the help in advance!
    David

    gnash, Welcome to the discussion area!
    Your problem is caused because you have 2 routers in your network. Therefore the wired computers are on a different subnet than the wireless computers.
    One solution is to replace the Linksys router with a simple Ethernet switch or hub.
    Another solutions is to reconfigure the AEBS so that it does not distribute IP addresses and then connect your network like this:
    modem->Linksys->[LAN] AEBS
    In this configuration, the Linksys will provide IP addresses to both the wired and wireless clients.

  • Wired port not conencting

    I have a poor wired connection running to my bedroom - only 4 wires available instead of the 8 wire Cat-5. I have had an old Airport connected (original model) and it worked fine. I tried to upgrade to the new Airport Extreme and the internet connection does not work. The Airport Extreme works fine at other locations so I dont think it has the problem. Further, I cannot get my Apple TV or Mac Book Pro to connect at this wire. The original Airport still connects fine, however. The ethernet is operating on wires 1,2,3 and 6 only.
    Any thoughts? (I realize that this is not proper set-up, but this is all I can do)

    Not sure what else to try. Could the wire type be part of the problem? Not using cat-5 but using 8 wire phone cable, and four of the wires are being used for the phone jack. Still seems strange that everything would be fine with Airport device (802.11B only) and not with any of the 802.11G or N devices I have tried (Linksys, Airport Extreme N, Apple TV)

  • Wireless printing with 2 (or more) printers + manual network configuring

    Here's my previous question:
    Network configuration: Cable modem (Linksys)-Wired cable router (Linksys)-Airport Extreme Base Station. Wired cable router is used for VOIP phone which is left on 24/7. Base station is shut off when not in use. I had 2 printers, HP multifunction and Samsung color laser printer connected to the Airport via a USB hub, but I could only print from 1. The printer I wanted to use had to be ON and then the Airport turned on to recognize it. So, I purchased a dLink DPR-1260 wireless printer hub. It had to be configured with a Windows operating system, which I did with an XP business laptop. The printer hub had to be configured wired and then the Cat 5 cable removed. The IP address: 10.0.1.2 (dynamic) is what Airport gives whenever anything is plugged into that port. MAC address: 001E589D8035 (which is what the printer hub says on it). SSID is correct. Raw TCP port and LPR/LPD enabled. Re-established Firewall and WPA2 security. Both printers work fine (even scan on HP) wirelessly with Windows XP laptop.
    However, neither printer works with either MAC (G5 or iBook) Although they both (HP & Samsung) appear to be ready and start the printing process by downloading percentages of the job.
    New info: The IP address of the dLink (DPR-1260) print server is now 10.0.1.3 (Airport is 10.0.1.2) I can connect to 10.0.1.3 thru Safari (or Firefox) and see the device info. I can't configure there. dLink told me to manually configure in network preferences. Their instructions told me to manual change the print server address to 102.168.0.x (x not 10). Then make Appletalk active. When I tried to add the DPR-1260 on the network is said IP Config 10.0.1.3 in use by 00:1e:58:9d:80:35 I guess I need to start over. How can I add the DPR-1260 manually to the network?

    xee -
    You have two simultaneous problems. Print Server setup, and network-capable CUPS driver required for each printer. Unless either printer is a postscript one, the drivers provided by the manufacturers are Carbon-type, limited to exactly what they programmed it for - probably USB only. That's why Airport Extreme/Express have an advantage over other print servers - Apple has put Mac-to-Mac printer sharing into Extreme/Express, so a USB-only driver works over the network. Other print servers require use of the industry-standard comm protocols LPD or raw port 9100 (=HP Jetdirect) or IPP. Those standard protocols are provided by CUPS and you have to use a CUPS driver with them.
    Make it work:
    1. Allow the print server to get its IP address just as it has.
    2. Install CUPS drivers:
    http://www.linuxfoundation.org/en/OpenPrinting/macosx
    or
    http://www.printfab.net

  • Airport Extreme: How to connect a Linksys VOIP device via ethernet

    Hi there!
    I am trying to connect Linksys PAP2T device via ethernet to my Aiport Extreme. It gets an address assigned 10.0.1.2 but when I access the device, I am not able to connect to internet. Do I need to key in my network password anywhere?

    Okay, so to answer my own question after considerable sleuthing . . . for anyone else trying to do this:
    Connect your computer to the bridge using an ethernet cable, then open a browser and enter the following address: http://169.254.1.250
    This will take you to a login page: leave the username field blank, enter "admin" in the password.
    You will see the Cisco setup page. I selected manual setup and entered the name of my network and password. I got a progress bar and finally the wireless network light on the bridge started flickering.

  • Argh! Trying to Replace Linksys with New Airport Extreme...

    Been fighting with this for hours...about ready to take the new Airport Extreme back ...Here's the deal:
    I currently have a very wired and wireless 2story home professinally set up with 2 Linksys devices as the primary network and a couple previous generation airport expresses as extenders.   Due to video, audio and other systems the primary router for the network/WAN closet out in the garage needs to remain on the primary Linksys (non wifi) router.  I want to replace the Linksys Wifi router (see below) that is puposely set up and has worked for several years as a double NAT config with the new Airport Extreme but i have tried duplicatiing the exact configs from the Linksys router and all the various ways you can use the Airport Express in DHCP/NAT and even in Bridge mode and it still wont work!  I've never considered Linksys software easier (and definately more flexible and informative) to use than Apple until this experience!  Very frustrating....  I'm being very explicit and using the typical Linksys config profiles below so as to hopefully help you translate this into specific configs i can wrangle into the Airport Extreme to make it work like the 
    Current Primary Network:
    Current WAN Router / + 24 Port Switched LAN Network (for wired ethernet access ports used throughout house) > Linksys BEFSX41 + Linksys 24 port Switch locted in a custom built data /video / audio closet in garage
    WAN IP:  DHCP
    LAN IP:  192.168.1.1
    Subnet Mask: 255.255.255.0
    Current WiFI Network > Linksys WRT160Nv2 (currently conected to the 24port switch via a hardwired ethernet wall port upstairs in my office) 
    Internet Connection Type: Static IP
    WAN IP:  192.168.1.2
    Subnet Mask: 255.255.255.0
    LAN IP:  192.168.0.1
    Subnet Mask: 255.255.255.0
    Per config notes from the network engineer who i worked with to build this network when i built the house
    "this allows the 192.168.0.x wifi device to successfully route to the 192.168.1.x wired router (and vice versa)"
    My goal is to replace the Linksys WRT160Nv2 with the new Airport Extreme (whose range and ability to reach both upsatirs and outside to the beach is MUCH better) and locate it DOWNSTAIRS and connect it in the same way as the Linksys (via an ethernet port in the living room) to the same switch / router in the data closet.  
    I have tried to set up the new Airport Extreme to replicate this config several different ways both bridged and not bridged (including telling it to ignore the double NAT warning) with the latest.   I am pretty sure non-bridged is the right way to do it but i seem to lack a config parameter to tell the Airport Extreme to replicate the equivalent of the WRT160Nv2 settings despite trating all the submenues and options on the airport extreme set up / Airport Utility App.  Do i have to telnet directly into the Airport Extreme config files to do this natively?  Help!
    PS - no i cannot / will not put the Airport Extreme in to replace the primary Linksys router in the data closet - there is no way it will fit or that its wifi could penetrate the EMI and insulation of all the other electronics in the data closet out in the garage and get a good connection into the house

    The trick on the airport extreme is to change the DHCP .. when you change the DHCP it changes the actual IP of the AE..
    So go to the setup and open the dhcp, in the network options and you can select by arrow the first two octets and replace the third.
    I just posted info on this in another post..
    https://discussions.apple.com/thread/5134560?tstart=30
    Does this answer your question, as I am a bit unclear otherwise??
    I have to say I do not like using double NAT.. it is becoming worse and worse as the amount of material on the internet that requires interactive connection increases.. you block so much by doing this.. double NAT is an issue .. not just ignore the warning.
    There is no reason why you need double NAT.. you should have a single flat network. If you need to keep some things isolated from others the correct way to do it is vlan.. but you will need a better router than the old linksys to do it. And possibly a managed switch. Nowadays a managed 24 port gigabit switch is not a bad price at all.

  • Can't use my HP Deskjet F4580 Wireless Printer with the AirPort Extreme Base. The printer is NOT connected at the USB port of the AirPort Extreme, and is placed in another room. It worked just fine with my previous router (Linksys WRT54G). Help me!

    Hey Guys!
    I just got my AirPort Extreme Base, but I can't use my HP Deskjet F4580 wireless printer with it.
    The printer is not connected to the AirPort Extreme's USB port. It is placed in another room, and I'd like to use it (the printer) wirelessly (not connected to the USB port os the AirPort Extreme), as I used to. There is no place for the printer close the AirPort Extreme. It worked just fine with my previous wireless router (Linksys WRT54G). I'm very disappointed with the AirPort Extreme Base Station because of that!...
    Can you help me? Please?!
    Thanks Folks!

    This must be a tough one, no suggestions at all.

  • Adding 3 Airport Extremes to Linksys WGT4400N in Bridge Mode  Not working

    I have a network that starts in a homerun closet and is expanded across 5 acres to differnet locations via CAT5e.
    Homerun Closet has Linksys WGT4400N with Cat5e running to three different locations on property. The cables are within length limitations.
    1st Airport Extreme N Running in Bridge Mode Connected and Working in Main House
    2nd Airport Extreme N Running in Bridge Mode Connected and Working in Guest House
    3rd Airport Extreme Replaced with new one Connected and Not Working in Office. This Airport Extreme N is configured just like the others but it cannot see the network. Cables Verified with Testers and Mac Pro at office location, works when ethernet cable is directly connected to system.
    Not sure what is going on. IS there s limit to the number of Airport Extreme N's used as bridges?
    I have 2 of ther working and the last is not. First Airport Extreme N for office was bad replaced.
    Thank You
    GldnSabre

    The Netgear wireless server has control over what what devices are allowed to connect.
    Unless you tell the Netgear what devices you want to allow to connect, it will allow any wireless device to connect as long as it knows the wireless network password.
    IF.... .you were using two AirPort Extremes, and not a Netgear, the two Extremes would communicate to each other....so you would only have to enter Timed Access settings on one router and other AirPort would automatically pick those settings up.
    But, even this was not the case until the last year or so when Apple updated firmware.  A few years ago, you might have had 2 Apple AirPort Extremes on the network, but you still had to manually set up Timed Access on both devices separately.
    Bottom line, you need to setup the equivalent of Timed Access on the Netgear router.

  • Extremely Slow Internet From Linksys WRTU54G-TM

    Hi all,
    I'm hoping someone can help me with this issue. I got the Linksys WRTU54G-TM for T-Mobile's @home service. According to the store employees, I should be able to just plug it in and it should work. I got it home, disconnected my old router (a Linksys WRT54G) and plugged it in. After a few minutes, the phone was up and working and sounds good; however, the internet coming off of the router is extremely slow (both wired and wirelessly). So slow that pages won't load. The title bar will tell you where you're trying to go; however the page will not load.
    Before calling for help, I contacted my internet provider (Cox Cable in Phoenix) and verified that the network was working and that my modem (Terayon brand) was good. When I hook the modem directly to the computer I get my full connection (around 20 megs down). Then I called T-Mobile and was connected to Linksys since the router was connecting and providing phone service.
    I spent an hour on the phone with Linksys. We flashed the firmware to the latest build, reset the modem to factory settings, reset the modem via the button on the back all the while power cycling the whole setup numerous times. The rep had me check some settings on my computer and I was able to ping from the cmd prompt. In the end, she felt that I received a bad router and said I should return it. She never mentioned cloning the MAC address; however, I saw that on the T-Mobile forums and tried it - no luck.
    I took the router back to the T-Mobile store and the rep happily exchanged my router for a new one. I got it home, plugged it in and have the same problem. Phone works, internet doesn't pass through the router properly.
    I went ahead and flashed the new router and reset it factory settings and that did not help (all the things I did with the Linksys rep with the first router). I'm going to be calling T-Mobile/Linksys again tomorrow but I wanted to see if there was anything anyone in these forums may know what I could try.
    With the second router, I did try plugging it into my old router (modem - old router - new router), the phone worked and the internet worked (both wired and wireless); however, the internet is not as quick as going through one router and I do not want to have two routers set up.
    Secondly, I looked at the configuration of my old one and set the new one to the same exact settings; however, one setting could not be matched. My old router is set to an operating mode of GATEWAY, the new one is set as ROUTER. The only options on the new one are router and bridge. Could this be the issue?
    It was recommend on the T-Mobile forums to run a speed test and post the results, which I can do tonight after I get home from work. 
    I've searched these forums, Google, the T-Mobile forums, the Cox forums at dslreports.com, and tons of other places and cannot find an answer. Based on the size of Cox, it's hard to believe I'm the only one with this issue. Any help would be appreciated. I have until Sunday to return the router and cancel the service without any termination fees.

    Try the following settings on the router...
    Change the Wireless Channel to 11-2.462GHz under Wireless tab...Under Advance Wireless Settings,Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304.Under Security tab,uncheck the option "Block Anonymous Internet Requests "...Power Cycle the router and check..  

  • I just bought the AIrport Extreme to replace an older Linksys wireless g router. But I am still getting a fairly low signal, not showing much improvement from the previous router. What gives?

    I just bought the airport extreme router to replace my older linksys g router because of a poor signal. Now that I have the new router running, I'm not seeing much improvement from the previous router! What gives?

    I too recently bought the Extreme to replace an old Linksys G and discoverd that the range of the new Extreme was surprising less than the Linksys.
    Nothing had changed otherwise; both routers were installed in the same place (on floor, under a cabinet in the middle of my house).
    I returned the Airport Extreme to Amazon and bought another (the latest version), and the same problem exists, i.e., I can't get a signal at the corners of my small home with the Airport, where I once could with the Linksys.
    I'm puzzled, but think that difference must be that the Linksys has 2 large external antennas and the Extreme's antennas are mounted internally.
    I've also noticed that Apple sells a wall mount for the Airport Extreme and am assuming this is to get the Airport up and out into the open in order to improve its 'send and receive' characteristics, no?
    If your Extreme is hidden in a cabinet or under some piece of furniture, I suggest you move it into the open and see if this helps extend its range.
    Hope this helps.
    John

  • HT4260 I have an AirPort Extreme and a linksys router. What is the best way to get 6-8 wired connections with ac speeds?

    I have an AirPort Extreme and a linksys router. What is the best way to get 6-8 wired connections with ac speeds?
    Appreciate your assistance.

    The answer depends on whether the AirPort Extreme is your main router....or...the Linksys device is your main router.
    In either case, the two devices must connect together using a wired Ethernet connection using CAT5e or CAT6 cabling.
    Any version of the AirPort Extreme produced within the last 5 years will have Gigabit Ethernet ports. In order to get the same speeds from the Linksys router, it will also need to be Gigabit Ethernet capable.
    If you need additional Ethernet ports, you will need to add a Gigabit Ethernet switch to either the AirPort Extreme or Linksys router.
    It is assumed that your other devices connecting to the AirPort Extreme and Linksys router will also have Gigabit Ethernet capability.
    Not sure why you mention "ac" speeds in your post. This relates to wireless connections, not wired.

  • Connect to Linksys Cable Gateway via AirPort Extreme Base Station?

    Thank you in advance for any replies.
    I have the following new setup:
    A G3 Blue tower running OS X 10.4.10 is successfully connected to the internet via a Linksys WCG200 Cable Gateway connected to RCN's cable internet service. The WCG200 unit has wireless capacity though it's connected to the G3 tower via ethernet cable.
    A second Mac (G3 iMac DV running OS X 10.4.10) is in another room in the office. I'd like to set it up with internet by wirelessly connecting with the existing WCG200 unit using an Airport Extreme Base Station (AEBS) I've recently acquired. To ensure a smooth process, I reset the AEBS to factory settings and installed the AEBS software (version 4.2) onto the iMac DV. Finally I plugged in the AEBS into the iMac DV using an ethernet cable plugged into the AEBS's WAN port (AirPort Admin Utility advised me to do so).
    That's the hardware configuration. Working out the software and configuration details is proving 'niggly'.
    First, I used the AirPort Setup Assistant to configure the AEBS. I told it to Set up a new Base Station, then to set it up as connecting to the internet using a Cable modem (the top option of two—the second was to set it up with internet through a LAN). I set up the name and passwords for the Base Station and had the utility configure the AEBS accordingly.
    No internet connection occurred. I tried using the Internet Connect utility in the Applications folder, but no button or visible option for connecting via AirPort appeared, as the Setup Guide indicated it should, only a button for a VPN appeared.
    I called Apple and asked whether it was even possible to connect to the internet using the AEBS talking wirelessly to the WCG200 unit. A tech told me it could be done by going into the AirPort Administration Utility, going into Configuration, clicking on the WDS tab and inputting the MAC address for the WCG200 unit, then going into the Airport tab and typing in the channel that the WCG200 is using. Note that the WCG200 unit has 3 MAC addresses listed; one each for “modem MAC address,” “WAN-MAN MAC address,” and “WAN-DATA MAC address”. I used the “modem MAC address.
    The Apple tech added that it might need further tweaking, but that Apple couldn’t provide this tweaking and that I might check various forums if need be.
    I followed the Tech’s advice, at which point the utility informed me that it couldn't use DHCP or NAT with this setup’ and to make sure that the "Distribute IP Addresses" checkbox was deselected under the Internet tab. This I did, but it was already deselected. I told the utility to update the AEBS accordingly, and restarted everything, including the 2 Macs and the WCG200.
    Result:
    No connection.
    Tried it again with the Ethernet plugged into the AEBSs LAN port, still no connection.
    Help! Can’t I get the AEBS to even see the WCG200? I know wireless is properly functioning in the WCG200 because another user with a Windows laptop connects to it wirelessly. The Mac Tech also mentioned that this could be relatively easy with an AirPort Express piece of hardware (Card? Base station?) but that it would be difficult with the Airport Extreme Base Station.
    At this point we’re willing to spend $100 on getting this up. What would be our best option in terms of equipment, or can connectivity be accomplished with what we have?
    Thanks again,
    skyheart

    skyheart, Welcome to the discussion area!
    In theory using WDS would provide what you need.
    In reality the Linksys device is not compatible with Apple's WDS and therefore this will not work.

Maybe you are looking for