Linksys WET54G connected to HP 420 AP change key types

Linksys WET54G connected to HP 420 AP change key types. it works for a day or so and suddenly it change the key-type from WPA-TKIP to WEP. communication fails of course. Restart the units will make it to work again sometimes you will have to restart it several times. some ide what the problem may be ?

Sorry we don't have an answer for you. Recommend you try the Linksys by Cisco forums at http://forums.linksysbycisco.com. Hopefully you find the solution there.

Similar Messages

Linksys WET54G problem

Hi,
I have a problem with my Linksys WET54G ethernet bridge.
Every time I set it up and then try and use it I don't get a connection.
This is my setup
iMac Snow G3 600MHz running OSX 10.2.8 connected via ethernet to
Linksys WET54G ethernet bridge which connects to
BT Voyager 2091 wireless modem router.
I can set the network connection preferences so I can get to the Linksys WET54G setup page and can see my wireless network.
When I close that browser and then change the network connection preferences to set the IP address using DHCP then I can't connect.
The Mac keeps assigning itself an IP address.
The WET54G does work OK - I'm writing this using a Win2000 PC connected to it.
Why does the iMac assign itself an IP address instead of using one from the modem/router?
Any help appreciated.
Regards
Jeremy Young

Hi,
Well here I am replying to my own post, just in case it help someone else in the future
I did get this combo to work:
I used a static IP address in the WET54 - something like 192.168.1.60
Then I use a static IP address in the Mac - something like 192.168.1.65
I also added the router IP address as the gateway - 192.168.1.1
And finally I added the DNS server from my router - I found this by going to the router setup and selecting manual DNS - and copying the numbers there.
Now everything is OK and I can surf without wires!
Jeremy Young

I have a Linksys Wrt54gs connected to a Cable modem. it w...

i have a Linksys Wrt54gs connected to a Cable modem.
it worked for about 8 months.
My kid pressed a button by accident and now it won't work.
the router just keeps resetting.
i unplugged everything.
conencted 1 computer, and everything is fine.
Received DHCP address.
Once i plug in a second computer it starts rebooting.
Both computers are set to DHCP.
NO internet connection is connected at this time for troubleshooting purposes.
Nothing is connected to the ethernet port on the Linksys router (port for internet access), only 1 and 2 are connected.
i reset the router and still nothing.
i can connect 1 computer via wireless and 1 computer via direct connection and all is good. Once 2 devices are connected via direct connections it starts resetting.
i can even connect the modem to the router (for internet access), and connect to the linksys router via wireless from my computer and get internet access.
But once i direct connect 2 connections, the router starts resetting.
i have reset and reboot it with every combination i can think of.

Its good that its working now.
If it happens again, try this :
Press the reset button on the router for 30 seconds. The Power light will start flashing. Turn the Router and the Modem OFF. Turn the modem ON first, wait for 10 seconds, turn the router ON, wait for 10 seconds, you should be ONLINE !!!
Do this when the computer os connected to the router with a cable.
than on the computer open Internet Explorer and in the Address Bar type : 192.168.1.1 and hit enter.
It'll ask for the password. The default password is admin.
Once in the setup page. Click on the Wireless tab.
In there Change the Network Mode to mixed. And change the SSID to your name.
Change the Channel to 11. And Enable the SSID Broadcast.
Save the settings here. After that Click on Wireless Security and configure it accordingly and Save the settrings.
Than click on Advanced Wireless Settings. In there Disable the SES function.
What is the firmware on the router ?
Click here to see the updated list of firmware.
For information on upgrading the firmware on the linksys routers :
http://linksysfirmwares.googlepages.com/upgradingfirmware
For information on wireless security :
http://linksysfirmwares.googlepages.com/wirelesssecurity
Message Edited by theonkar on 08-20-2008 04:48 AM
C | EH
linksyshelp.blogspot.com

My wireless keyboard no longer connects with my iMac since changing the batteries. It now shows as not connected, not paired and not configured. A friend recently connected his iPad to the iMac and since then the problem started. Any ideas to resolve this

My wireless keyboard no longer connects with my iMac since changing the batteries. It now shows as not connected, not paired and not configured. A friend recently connected his iPad to the iMac and since then the problem started. Any ideas to resolve this?

a friend told me that he wants my os x cd for my macbook pro to upgrade his imac.
The discs that come with your Mac are "machine specfic" and cannot be used on another Mac.

Linksys E1200 Router not saving Port Forwarding changes

Hi!
I am currently attempting to port forward on my Linksys E1200 Router and am not succeeding in saving my settings. I am attempting to open port 25565 though both Single Port Forwarding and Port Range Forwarding, and whenever I click the "save settings" button, I receive a full window message stating that my changes have been saved. Upon clicking this, I return to the previous screen whereupon my changes have been erased and my port has not been forwarded. Can anyone assist me with this? I've searched for hours through forums and tech help websites, but I can't find anyone else with this issue.
Issue:
Linksys E1200 Router not saving Port Forwarding changes.
I have tried:
-Restarting the Modem
-Restarting the browser
-Restarting the computer
-Tried to Port Forward through both the Single and Ranged Port Forwarding

Hi there. You can try another browser or a different computer. If it is the same thing, upgrade the firmware of the router. You can refer to this link on how to http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=0a6881b90224439b92c8d8f19ca42e5d_21511.xml&pid=80&...

My Ipad and itouch cannot be connected ti wireless router tried changing setting still cannot connect

my Ipad and itouch cannot be connected ti wireless router tried changing setting still cannot connect

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Iphone wont leave the settings app. cant turn off or return to home. tried connecting to itunes and no change

tried upgrading to ios7 then said i didnt have enough storage so attempted to delete apps in usage and turned my icloud on, now iphone wont leave the settings app. cant turn off or return to home. tried connecting to itunes and no change. help!

You need to reset the phone, but that requires a functioning on/off (lock) button. Time to visit Apple.

AP log got Connection lost to WLCCP server, changing to Stand-Alone Mod

Our customer has about 200 Autonomous APs(Version=c1200-k9w7-tar.123-2.JA2),WLSM(Maintenance img(1.1(2)),Application img=12.2(15)XR2), Sup720 IOS=s72033-jk9o3sv-mz.122-18.SXD3.bin.The static WDS point to WLSM,somme of AP will fail with log"Connection lost to WLCCP server, changing to Stand-Alone Mode".
Any ideas about solutions on this?

You will receive this error message if the AP loses its connectivity with the WDS. This can happen if the radios are flapping, as well as if there are problems with authentication / registration with WDS. If the AP is powered using POE, please ensure that you configure the proper poe support on them. Also check if authentication is happening correctly. Debugs on the AP and the logs on the AAA server will help troubleshoot this issue.

How to change nat type 3 to nat type 2 for Plastation 4?

how to change nat type 3 to nat type 2 for adaptation 4? i am havng a complicated time with this im'm just trying to play online and been at it fotr 3 days i have tried about everuyhing n portforwarding.com i have a Cisco Linksys E1000

Hi ceasar14. I actually found some steps (from a source) that worked for me. I'm not sure if it will work for you. Here are the steps:
1. Get the MAC address of your PS3. To find your MAC address simply go to
Settings > System Settings > System Information
2. Assign a static IP address on your PS3.
3. Access your router's user interface to open a few ports.
4. Under Applications and Gaming > Port Range Forwarding, open the following ports:
TCP: 80, 443, 5223
UDP: 3478, 3479, 3658
5. Once this is done, powercycle your PS3 and the router.
6. Run a connection test and check if it is now on NAT2.
Good luck.

Hello! I have in my home 2 iMac, 2 iPad, 2 iPhone, and 1 air base extreme. I don't succeed to connect more than one divice from similar type. I tried everything what I knew. I build another network, etc...

Hello! I have in my home 2 iMac, 2 iPad, 2 iPhone, and 1 air base extreme. I don't succeed to connect more than one divice from similar type. I tried everything what I knew. I build another network, etc...
So only one imac, only one ipad..and so on simultain.
More over, all the divices are conect through wifi to air base but are not receiveing internet as i told above.
I need to disconnect one device to have internet on the second one from the same type!
Could somebody help me?
Many Thnaks,
dan

If your network configuration is:
Cable modem > (Ethernet cable) > [WAN] AEBS > (wireless) > Macs, then
AirPort Extreme Base Station Setup (AEBS) w/High-Speed Cable Modem
Modem/Router Power ReCycling
- Power-off the Cable modem, AEBS, & computer(s). (If possible, leave the modem off overnight.)
- Power-on the Cable modem; Wait at least 30 minutes.
- Power-on the AEBS; Wait at least 5 minutes.
- Power-on the computer(s)
Perform a "hard" reset of the AEBS.
- (ref: http://docs.info.apple.com/article.html?artnum=107451)
Setup the AEBS
With the network components powered down, set up the AEBS, using the AirPort Admin Utility, connect your computer directly (using an Ethernet cable) to the LAN port of the AEBS, and then, try these settings:
AirPort tab
- Base Station Name: <whatever you wish or use the default>
- AirPort Network Name: <whatever you wish or use the default>
- Create a closed network (unchecked)
- Wireless Security: Not enabled
- Channel: Automatic
- Mode: 802.11b/g Compatible
Internet tab
- Connect Using: Ethernet
- Configure: Using DHCP
- WAN Ethernet Port: Automatic
Network tab
- Distribute IP addresses (checked)
- Share a single IP address (using DHCP & NAT) (enabled)
Once you verified that you can get Internet access for all of your computers, you should secure your wireless network. To do so, I suggest that you make these changes:
AirPort tab (optional)
- Create a closed network (checked)
Change Wireless Security
- Wireless Security: WPA Personal
Base Station Options - WAN Ethernet Port
- Enable SNMP Access (unchecked)
- Enable Remote Configuration (unchecked)
- Enable Remote Printer Access (unchecked)
Wireless Options
- Transmitter Power: 10%
Access Control tab (optional)
- + <add the computer(s) that will access this wireless network>

I want to change the type of a Result Set

Hello all,
I was using a ResultSet object to store the results of a query, and when i attempted to use the ResultSet function "last()", i had a SQL exception saying that I cannot use this function on a ResultSet of type TYPE_FORWARD_ONLY. How can I change the type of a ResultSet to be for example TYPE_SCROLL_SENSITIVE, so that i can use the 'last()' function? I can only find a function caleed getType() but i want a function to allow me to set the type of the ResultSet.....
Thanks a lot

The type is determined when you create the Statement or PreparedStatement object. See the documention for Connection.createStatement or Connection.prepareStatement.

Change lock type on large table

I have a table which is about 2G size. the lock type on this table is set as AllPage. I think this cause performance issue when issue select query, many SH lock applied. I try to change the lock type to datarow, which should have no lock when issue select as document indicated.
but when I try it with DBArtisan, it took longtime and never end. Then I stop the app and connect it again. I found the lock type do change it to datarow. but there is a new table name like mytab_3309ac22 created.
then I try to change lock type again on other table and got following info:
You can not run Alter Table Lock in this database because the 'select into/bulkcopy' option is off.
Looks like dboption changed. So want to know if this is safe for data when change lock type? how to ensure it is done properly?

Hi Kent,
The problem is that allpages has different physical structure than datarows.
Changing from one format to another requires to rewrite the whole table.
There are a few ways to achieve this goal.
a) running the alter table directly:
alter table x lock datarows
This command causes to make the change internally. This is the fastest way to do that, but it requries to set the 'select into' option on the database. And that might be problematic because it breaks the the transaction log sequence.
If you don't have the option set on the database you are not able to run the command.
b) doing it manually:
1. create a second table with datarows scheme
2. copy the rows to the table
3. dropping the old and renaming the new table
If you have a very busy system with little time for downtime then that would be the only solution. You can create triggers to manually log all the changes on the old table if that process would take too long.
At the end you would have to add all the foreign keys to the new table. And of course recreate the indexes.
I don't exactly know what DBArtisan is doing, but since you don't have the 'select into' option then probably it is running the second option. This new table with name mytab_3309ac22 might be the effect of the operation broken in the middle. How many rows has this table have? And what is the scheme?
If you have plenty of time then I would recommend to run the alter table command together with the 'select into' option. Anyway you won't have any progress bar during this operation so it is very hard to predict the time of the operation.
HTH,
Adam

Change cursor type in Yosemite

Is there any way to change the type of cursor in Yosemite? Not the arrow pointer for the mouse or trackpad, but i mean the cursor -- right now it's just the default vertical line, but could I change it to a block, like in the Terminal application? I can't find anything in the accessibility window of preferences.

You can't. The recordset returned by a command object (which
is what's used
in the 8.02 update) is always a read-only, forward-only,
server-side cursor.
If you need to change any of that, don't use the Execute
method of the
command object. Construct a recordset with the options you
want. Do NOT
set the active connection on the recordset; leave that out.
Pass the
command object as the source of the recordset object, then
use the
recordset's Open method. That's pretty convoluted, but it
lets you retain
the most DW-generated code.
Your other option is to use the recordset object only and
plain text
parameters like DW 8.01 rather than a command object with
parameter objects
like DW 8.02.
That change was fundamental to the ASP server model and
probably should not
have been part of any update, but saved for the next release.
It at least
deserved more than a .0x update to the version number. At
least call it
8.1.
"riprod7" <[email protected]> wrote in
message
news:e8jdb6$ou0$[email protected]..
>I have never been more unhappy with an update in my live,
I basically have
>to
> learn everything from scratch again with DW 8.02.
>
> When pulling a recrodset you used to be able to set the
CursorType in the
> code. That is gone now.
> As a result I cannot use rs.MoveFirst or rs.Move -2 to
browse around
> records.
> I get the following error.
>
> Microsoft OLE DB Provider for ODBC Drivers error
'80040e24'
> Rowset does not support fetching backward.
>
> How do I change the CursorType in this horrible update!
Thanks
>

How can I use srvctl command line for change "Failover type" and "F method"

Hi all,
I am using Oracle One Node (11.2.0.3), and I have a service:
/u01/11.2.0/grid/bin/srvctl config service -d orcl
Service name: orcldb
Service is enabled
Server pool: orcl
Cardinality: 1
Disconnect: false
Service role: PRIMARY
Management policy: AUTOMATIC
DTP transaction: false
AQ HA notifications: false
Failover type: NONE
Failover method: NONE
TAF failover retries: 0
TAF failover delay: 0
Connection Load Balancing Goal: LONG
Runtime Load Balancing Goal: NONE
TAF policy specification: BASIC
Edition:
Preferred instances: orcl_1
Available instances:
I would like to change "Failover type" and "Failover method" to:
Failover type: SELECT
Failover method: BASIC
How can I do that? Is there any graphical tool for it? Or, How can I use srvctl command line for change it?
Thanks in advance.
Leonardo.

user10674190 wrote:
Hi all,
I am using Oracle One Node (11.2.0.3), and I have a service:
/u01/11.2.0/grid/bin/srvctl config service -d orcl
Service name: orcldb
Service is enabled
Server pool: orcl
Cardinality: 1
Disconnect: false
Service role: PRIMARY
Management policy: AUTOMATIC
DTP transaction: false
AQ HA notifications: false
Failover type: NONE
Failover method: NONE
TAF failover retries: 0
TAF failover delay: 0
Connection Load Balancing Goal: LONG
Runtime Load Balancing Goal: NONE
TAF policy specification: BASIC
Edition:
Preferred instances: orcl_1
Available instances:
I would like to change "Failover type" and "Failover method" to:
Failover type: SELECT
Failover method: BASIC
How can I do that? Is there any graphical tool for it? Or, How can I use srvctl command line for change it?
Thanks in advance.
Leonardo.srvctl modify service -d database_name -s orcldb -q TRUE -m BASIC -P BASIC -e SELECT -z 180 -w 5 -j LONG
Also see
11gR2(11.2) RAC TAF Configuration for Admin and Policy Managed Databases [ID 1312749.1]

How to change latency type to fast?

How to change latency type to fast?

ADSL Line Status
Connection information
Line state:
Connected
Connection time:
5 days, 03:08:00
Downstream:
16,403 Kbps
Upstream:
948 Kbps
ADSL settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
3.1 dB / 4.7 dB
Line attenuation (Down/Up):
30.5 dB / 16.2 dB
Output power (Down/Up):
20.9 dBm / 12.2 dBm
FEC Events (Down/Up):
313987846 / 3701
CRC Events (Down/Up):
2155 / 18271
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
Loss of Link (Remote):
0
HEC Errors (Down/Up):
49173 / 14016
Error Seconds (Local/Remote):
0 / 17361

Linksys WET54G connected to HP 420 AP change key types

Similar Messages

Maybe you are looking for