Linksys WRT54G power/cable issues.

So I just bought a Linksys WRT54G for $4 at a flea market, but the lady didn't have the exact power cable, so I just grabbed whatever was the closest. The power cable works, but every couple of minutes the router's power light will start blinking and the internet is out. The good news is it comes right back on after about 20 seconds and I also have an original Linksys power cable from my other router, which fixes the issues.
In conclusion....I know the power cable is whats causing it. A new oem charger is like $12 from amazon, but is there any cheaper alternatives from walmart/etc?
Unless someone knows if there is something else causing the issue, but like I said, when I plug an original linksys charger in it from another linksys router, the issue is not there.

Universal power adapters should work provided with the proper output voltage and amperage. It's adjustable so it would be easier to match the requirement. Check your original linksys adapter then match the output voltage (V) and amperes (A or mA).

Similar Messages

  • Linksys WRT54G v5 - Connection issues

    Good evening,
    I picked up a new WRT54G (v5) the other day to replace an old BEFW11 router, and so far have been far less than impressed.  I have one computer on the wired connection, and one on wireless.  It seems, though, that if the wireless system is running any P2P software (Limewire, in this case), or anything else which creates a large number of simultaneous connections (BitTorrent for d/ling CD images, for instance), the router simply dies.  Although any existing TCP connections are fine (e.g. MSN Messenger switchboard connections, though not _new_ conversations), it is virtually impossible to generate any new TCP connections.  They appear to connect immediately, and then disconnect less than a second later.  This occurs for HTTP, SSH, Telnet, IMAP, and SMTP connections, so far as I've tried.
    A hard reset of the router seems to be the only thing that helps. 
    I ran into similar issues with the BEFW11, and ended up using it only as an access point, and relying on an old D-Link DI-704P to take care of NAT -- and this worked fine.  But in this case, I want to take the DI-704 with me when I move, not leave it here ... and so I would really prefer if the Linksys could, uh, do what it's supposed to in the first place. 
    I tried upgrading the firmware to v1.00.9, but after sitting there for a few minutes I ended up with a "this page cannot be displayed" error from I E.  I'm going to give it another shot, but am a little hesitant to reboot the router at this point because I have no idea if it will be toast at that point or not. 
    EDIT: Now upgraded to v1.00.9.  Apparently this doesn't work over HTTPS, but it worked fine via HTTP itself.  We'll see if this has made a difference ...
    I see some similar reports from other people.  Any suggestions?
    Message Edited by tibbbsa on 07-08-2006 09:00 PM

    tibbbsa wrote:
    I see some similar reports from other people. Any suggestions?
    yeah use a WRT54GL instead. my website is unindated with wrt54g/GS v5 and v6 router problems. how linksys has been able to ignore this problem is beyond me. the WRT54GL is by far the better router. (linux based)
    Regards Simon
    NAS: TS-459 Pro - 3.6.1 Build0302T - 4 x 1TB Samsung HD103SJ : EXT4 - APC ES 700VA UPS
    QPKG: WordPress 3.4, TwonkyMedia 6.0.39 QPKG - Zenphoto1.4.2.1 [7802] - phpMyAdmin v3.3.10
    Network: Netgear DG834G V4.01.40 - DGTeam Rev. 0849 -> Cisco RV220W 1.0.4.13, Cisco SLM2008, Dlink DSM-520, Xbox360

  • Power Cable issue with NOMAD

    I've had my nomad zen for over 2 years and it's worked great. However yesterday i went to plug it in to charge and no power was going into it. I felt the mid cable box (which i think converts AC to DC) and it was warm. So this a.m. i tried charging again and nothing... is it safe to assume that the charger is dead? do they sell creative ones at best buy, do i need toorder it from this website, or can i find a uni'versal one at radio shack and make sure it's set properly? it hasn't been 24 hours and i'm already starting to miss this **bleep** thing!
    pezman

    It's possible it's dead. A quick and easy test is to get a multimeter and test whether there's any voltage output at the tip.
    If it's dead Creative sell replacements at their online store. You can also buy generic replacements, but they must have a suitable tip size of course as well as produce 5V @ .5A minimum rated current.

  • WRT54GS Power/WLAN issues

    I have the WRT54GSv6.0. On Saturday I had my network connected and working perfectly, but on Sunday noticed that the connection to my network kept coming for 5-10 secs and then going.
    Having checked my router I noticed the Power light is on for 5-10 secs and then flashes  causing with it the WLAN light to go out until the power light comes back on. Because this happens the network connection cannot connect.
    Can anyone help and tell me how to resolve this problem?
    Thanks

    Hi….
    Had you experienced any power outage or a power surge before the problem occurred? You can also try resetting the router by pressing the reset button at the back of the router for 30 seconds. After reseting the router powercycle the router for 30 seconds and then reconfiguring it for your internet connection.

  • WRT54GS power supply substitute?

    hi, i moved recently and i lost my linksys' WRT54GS power supply somehow.
    i plugged a scanners power supply i had, and it didnt blow up.
    the WRT54GS power supply was 12V 0.5A according to this sites specifications, ant the one im using now is 12V 1.25A
    will i toast my router if i continue using this power supply?
    thanks.

    What a terrible response Ridicully. No, it won't hurt your router. If the router wants a 12V DC .5A adapter and you use a 12V DC 1.25A adapter you are fine. The current rating is the capability of the adapter NOT what it will inject into the router. The router only needed a 1/2 amp of 12Volts, the printer adapter can supply 1.25 amps.. more than enough. The only thing to be carefull of here is the supply voltage.. make sure they match 12V DC to 12 DC. I once plugged a 12V AC adapter into a 12V DC device... NOW THAT WILL CAUSE bad things to happen.

  • Problem Connecting Linksys WRT54G to Arris TM402P/100 Cable Modem

    The Problem
    Cannot get an internet connection attempting to install a Linksys WRT54G router between an Arris TM402P/100 cable modem and the local network.
    Prior Configuration
    Previously had DSL, with the Linksys WRT54G wireless router between the DSL modem and the local network, which worked perfectly.
    New Configuration
    This friend recently changed his broadband from DSL to Comcast cable, and he also has phone and television service over the same connection.  The installation tech connected the cable modem directly to a desktop computer and left the Linksys router out.
    The direct connection between the cable modem and the computer works fine, but he and his wife each have laptops and would like to us the Linksys router to connect wirelessly.
    This is the TCP/IP configuration of the FAMILY workstation connected to Comcast
    directly through Arris TM402P/110 cable modem:
    Windows IP Configuration
           Host Name . . . . . . . . . . . . : family
           Primary Dns Suffix  . . . . . :
           Node Type . . . . . . . . . . . . : Hybrid
           IP Routing Enabled. . . . . . : No
           WINS Proxy Enabled. . . .. : No
           DNS Suffix Search List. . .. : hsd1.wa.comcast.net.
    Ethernet adapter Local Area Connection:
           Connection-specific DNS Suffix  . : hsd1.wa.comcast.net.
           Description . . . . . . . ...... . . . : Intel(R) PRO/100 VE Network Connection
           Physical Address. . . . . . . . . : 00-11-11-6F-FB-69
           Dhcp Enabled. . . . . . . . . . . : Yes
           Autoconfiguration Enabled . . . . : Yes
           IP Address. . . . . . . . . . . . : 67.185.155.0
           Subnet Mask . . . . . . . . . . . : 255.255.254.0
           Default Gateway . . . . . . . . . : 67.185.154.1
           DHCP Server . . . . . . . . . . . : 68.87.69.10
           DNS Servers . . . . . . . . . . . : 68.87.69.146
                                                        68.87.85.98
           Lease Obtained. . .  . . . . . . : Tuesday, January 09, 2007 5:39:26 PM       Lease Expires . . . . . . . . . . : Friday, January 12, 2007 9:58:23 AM
    I cannot find a configuration on the Linksys WRT54G that will allow me to connect to the internet through the Arris TM402P/110 modem.  Have tried (1) setting the Linksys to use a dynamic WAN address, (2) setting the Linksys to static IP 67.185.155.0 with TCP/IP settings taken from the above configuration, (3) cloning the MAC address of the desktop computer's NIC and trying both (1) and (2) again.
    The error message says that the network cable is not connected.  Is it possible that the connection between the router and cable modem requires a cross-over cable?
    Any suggestions?

    on the router's ui... keep the internet type to dhcp....clone the mac address and then do a power cycle...ensure that the modem is completely powered off during the power cycle...if you have a battery back - up , remove the battery...after a minute , put back the battery and then plug in the power cable in the modem...   
    let me know if this helps you.... 

  • I have a Linksys Wrt54gs connected to a Cable modem. it w...

    i have a Linksys Wrt54gs connected to a Cable modem.
    it worked for about 8 months.
    My kid pressed a button by accident and now it won't work.
    the router just keeps resetting.
    i unplugged everything.
    conencted 1 computer, and everything is fine.
    Received DHCP address.
    Once i plug in a second computer it starts rebooting.
    Both computers are set to DHCP.
    NO internet connection is connected at this time for troubleshooting purposes.
    Nothing is connected to the ethernet port on the Linksys router (port for internet access), only 1 and 2 are connected.
    i reset the router and still nothing.
    i can connect 1 computer via wireless and 1 computer via direct connection and all is good. Once 2 devices are connected via direct connections it starts resetting.
    i can even connect the modem to the router (for internet access), and connect to the linksys router via wireless from my computer and get internet access.
    But once i direct connect 2 connections, the router starts resetting.
    i have reset and reboot it with every combination i can think of.

    Its good that its working now.
    If it happens again, try this :
    Press the reset button on the router for 30 seconds. The Power light will start flashing. Turn the Router and the Modem OFF. Turn the modem ON first, wait for 10 seconds, turn the router ON, wait for 10 seconds, you should be ONLINE !!!
    Do this when the computer os connected to the router with a cable.
    than on the computer open Internet Explorer and in the Address Bar type : 192.168.1.1 and hit enter.
    It'll ask for the password. The default password is admin.
    Once in the setup page. Click on the Wireless tab.
    In there Change the Network Mode to mixed. And change the SSID to your name.
    Change the Channel to 11. And Enable the SSID Broadcast.
    Save the settings here. After that Click on Wireless Security and configure it accordingly and Save the settrings.
    Than click on Advanced Wireless Settings. In there Disable the SES function.
    What is the firmware on the router ?
    Click here to see the updated list of firmware.
    For information on upgrading the firmware on the linksys routers :
    http://linksysfirmwares.googlepages.com/upgradingfirmware
    For information on wireless security :
    http://linksysfirmwares.googlepages.com/wirelesssecurity
    Message Edited by theonkar on 08-20-2008 04:48 AM
    C | EH
    linksyshelp.blogspot.com

  • I have a 27" thunderbolt display NOT the iMac, and I'm trying to connect my xbox 360 to it via the Belkin AV360. I plug everything in and it does not work? I check all the power cables and and connections and still not he issue. Iv'e tried C-F2 also. Help

    I have a 27" thunderbolt display NOT the iMac, and I'm trying to connect my xbox 360 to it via the Belkin AV360. I plug everything in and it does not work? I check all the power cables and and connections and still not he issue. Iv'e tried C-F2 also. has anyone used this devive (AV360) on there own 27" thunderbolt display (not the imac) and gotten it to work? If so I'd appreciate the help.

    There are multiple reasons that lead to issue. You should read the troubleshooting guide to get the right solution to solve the issue: iPhone, iPad, or iPod touch not recognized in iTunes for Windows - Apple Support

  • Linksys wrt54g setup issue

    hello all,
    ive recently setup a cisco modem with a linksys wrt54g i had lying around for a friend.   i enabled the security (WPA/WPA2) and changed the name for the wireless connection. I restart every thing and i see the new name wireless secured connection but unfortunately a while later i see that the original unprotected 'linksys' access point still available. ive tried resetting the router and doing the process over a couple times. first by enabling the password and then changing the name and vice versa but i always see the unprotected access point show up again and again and its driving me crazy. i know its my router as well because when i disable the router both connections are lost. so basically my router is showing 2 names.
    any help would be greatly appreciated.
    thanks!

    Did you try removing the entire preferred network from the preferred list? If not then try to remove the entire preferred network from the list and then check it still shows the default network of the router “Linksys” or not. Here is the link for removing the preferred wireless network from the list:
    http://w3techie.com/2009/change-wireless-preferred-networks-xp-vista-and-windows-7/

  • How to hook up a Linksys WRT54G to Motorola NVG589. PLEASE HELP!

    Hello,  I have recently switched over to AT&T Uverse and I am loving it. One thing I miss is having extra ethernet ports to plug in my desktop computer and my Xbox 360. When the Uverse technician came in, he installed a Motorola NVG589 modem that also has a built in wireless router. He also installed a VAP2500 as a receiver for 2 wireless TV boxes. The VAP2500 plugs into the back of the Motorola NVG589. 3 other TV boxes are plugged into the back as well.  My dilemma is the fact that all of the ports are being taken up. I need at least 2 more ethernet ports free so I can hook up my Xbox 360 (my model doesn't have built in wifi) and my desktop computer as well.  I told the technician this when he installed the system and he told me to go on ebay and buy 2 cheap splitters and split 2 TV boxes that are coming into the NVG589. I did so. It didn't work out. I called up AT&T and the guy over the phone said that was the worst thing I could've done. He told be I should buy an ethernet switch.  I had my Linksys WRT54G (Version 6) router laying around at the time and realized that it had a built in ethernet switch. I want to get this to also function as another Wifi hotspot because I have an old PowerMac G4 downstairs that won't connect to the NVG589 for some reason (it says connection timeout). I am guessing that the wifi card in the system may be too old to connect to the modern NVG589.  So, I need the 2 extra ethernet ports and another Wifi hotspot from this setup. I have tried multiple things to get this to work.  The closest way I could get it to work was when I plugged an ethernet cable from the LAN port on the WRT54G to port on the back of the NVG589. I then plugged the TV box ethernet cable I had to disconnect into the second LAN port on the WRT54G as well as plugging my Xbox 360 into the 3rd LAN port and my computer into the 4th LAN port. This worked great for the TV box and the Xbox 360. However, the computer's ethernet connection ran very slow and the WIfi from the WRT54G was very slow as well. The Wifi from the NVG589 was slow too.  I unhooked that setup and put it back to what it was beforehand.  Is there anyone that knows of a flawless way of setting this up?  Any articles someone can link me to? I've heard of bridging the NVG589...would that help me? How exactly would I do that? Please HELP. I have attached pics. On the back of the NVG589 - green ethernet is the DSL cable, both white ethernet cables along with the black one are TV boxes and the yellow ethernet cable is the VAP 2500.  Thanks! 

    craigarc303 wrote:
    Hello,  I have recently switched over to AT&T Uverse and I am loving it. One thing I miss is having extra ethernet ports to plug in my desktop computer and my Xbox 360. When the Uverse technician came in, he installed a Motorola NVG589 modem that also has a built in wireless router. He also installed a VAP2500 as a receiver for 2 wireless TV boxes. The VAP2500 plugs into the back of the Motorola NVG589. 3 other TV boxes are plugged into the back as well.  My dilemma is the fact that all of the ports are being taken up. I need at least 2 more ethernet ports free so I can hook up my Xbox 360 (my model doesn't have built in wifi) and my desktop computer as well.  I told the technician this when he installed the system and he told me to go on ebay and buy 2 cheap splitters and split 2 TV boxes that are coming into the NVG589. I did so. It didn't work out. I called up AT&T and the guy over the phone said that was the worst thing I could've done. He told be I should buy an ethernet switch.  I had my Linksys WRT54G (Version 6) router laying around at the time and realized that it had a built in ethernet switch. I want to get this to also function as another Wifi hotspot because I have an old PowerMac G4 downstairs that won't connect to the NVG589 for some reason (it says connection timeout). I am guessing that the wifi card in the system may be too old to connect to the modern NVG589.  So, I need the 2 extra ethernet ports and another Wifi hotspot from this setup. I have tried multiple things to get this to work.  The closest way I could get it to work was when I plugged an ethernet cable from the LAN port on the WRT54G to port on the back of the NVG589. I then plugged the TV box ethernet cable I had to disconnect into the second LAN port on the WRT54G as well as plugging my Xbox 360 into the 3rd LAN port and my computer into the 4th LAN port. This worked great for the TV box and the Xbox 360. However, the computer's ethernet connection ran very slow and the WIfi from the WRT54G was very slow as well. The Wifi from the NVG589 was slow too.  I unhooked that setup and put it back to what it was beforehand.  Is there anyone that knows of a flawless way of setting this up?  Any articles someone can link me to? I've heard of bridging the NVG589...would that help me? How exactly would I do that? Please HELP. I have attached pics. On the back of the NVG589 - green ethernet is the DSL cable, both white ethernet cables along with the black one are TV boxes and the yellow ethernet cable is the VAP 2500.  Thanks!   Ya, the install tech must have been sleeping or texting or something during training.... or it's possible he misunderstood you and thought your were talking about needing extra phone ports, which could be accomplished with simple splitters. You were almost where you needed to be with your setup, you just missed some steps. Connect your wired computer only to one of the Linksys' LAN port. With the Linksys powered up press and hold the reset button for 15 seconds (will need toothpick or unfolded paperclip). This will perform a "factory" reset. When the Linksys is fully rebooted, log in to the Linksys. Do not configure the "Internet Connection Type" on the Linksys. Navigate to the "Wireless" section on the Linksys and configure the wireless. Do not use the same SSID (wireless network name) that the NVG589 uses. Save changes. Navigate to the "LAN" configuration on the Linksys and set the routers address to 192.168.1.1 and disable the DHCP Server. Save changes. This step will kick you out of the router. Power down your computer and the Linksys, run an Ethernet cable from a LAN port on the NVG589 to a LAN port on the Linksys, then power up the Linksys, and when it's fully rebooted, power up your computer. You should be good to go at this point. You will want to individually configure your wireless devices to use either the wireless network from the NVG or the wireless network from the Linksys. Otherwise they make keep jumping back and forth between the two, which will degrade performance for that device. You may still notice a slight to moderate performance drop for the wireless on both the NVG and the Linksys because they will be competing for the same wireless airspace along with the VAP2500.     
    How can you be in two places at once, when your not anywhere at all?
    I really want to become a procrastinator, but I keep putting it off.
    There are three kinds of people, those that can count, and those that can't.
    “Our great democracies still tend to think that a stupid man is more likely to be honest than a clever man, and our politicians take advantage of this prejudice by pretending to be even more stupid than nature has made them." :Bertrand Russell

  • Can no longer connect to internet wirelessly with Linksys WRT54G...

    Hi, all...
    I'm at my father-in-law's house. His home network setup is as follows:
    * Compaq desktop connected via Ethernet cable to
    * Linksys WRT54G, v3 (IP 192.168.2.1) connected via Ethernet cable to
    * Westell DSL modem provided by SouthEast Telephone (his ISP - IP 192.168.1.1)
    I set this equipment up for him about 18 months ago. His Compaq desktop connects perfectly to the internet, using the setup I described above, which I set up for him about 18 months ago. I *used* to be able to connect to the internet wirelessly (with both my IBM ThinkPad and my MacBook; my bro-in-law *used* to be able to connect to the internet wireless (with his Dell laptop).
    For reasons we don't yet understand, neither of us can connect wirelessly to the internet any longer. I have called Linksys, posted to their board, and read other threads here, so I am aware that MacBooks have some issues with Linksys routers. I'm getting ready to phone my father-in-law's ISP, to see if they can help.
    But... I don't understand why this used to work, but doesn't any longer. I would be very grateful for any help any of you great folks could provide, and I will gladly post here any detailed info on the setup that might be of help!
    Many thanks,
    Bill J.
    MacBook 2.0   Mac OS X (10.4.8)   iMac 17in Core 2 Duo 2.0, AirPort Extreme, AirPort Express, IBM NetVista M42

    Thanks for your reply.
    Actually the Linksys 2Wire modem works fine in OSX and when connecting via a Compaq PC I also have in the house. It is just on the MacBook running XP that it fails to "connect". XP see's the network but cannot connect.
    Also, I downloaded again bootcamp and created a fresh driver CD, reinstalled the driver and received the same error: 1706 No valid source could be found for product Macintoish Drivers foir Windows XP.msi.
    I looked at the directory on the CD and it appears that there are no driver files, only documentation.
    I called Apple, got no help, called Microsoft, spent 1.5 hours talking to them
    they were no help either.
    I sent a messge to the bootcamp beta mail address informing them that it seems the drivers are not being downloaded with bootcamp.
    Thx again.

  • Linksys WRT54G Wireless-G Router Not working

    I have a Linksys WRT54G Wireless-G Router and it has worked good for a couple months and yesterday it stopped. When I plug it in all the lights are lit even though there arent any ethernet cables connected and the power light blinks constantly. I tried holding the reset button on the back and it didnt help. Anyone know whats wrong or anything I can try to fix it?

    You need to try again to reset the router to factory defaults.
    To reset your router to factory defaults, use the following procedure:
    1) Power down all computers, the router, and the modem, and unplug them from the wall.
    2) Disconnect all wires from the router.
    3) Power up the router and allow it to fully boot (1-2 minutes).
    4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
    5) Power down the router.
    6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
    7) Power up the router and allow it to fully boot (1-2 minutes).
    8) Power up the computer (if the computer has a wireless card, make sure it is off).
    9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
    10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
    If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
    If you cannot get "Reply from ..." in step 9 above, your router is dead.
    If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
    If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
    Please let me know how things turn out for you.

  • Can connect to Linksys WRT54G but can't get to the internet.

    PowerBook G4 17" 1GHz with OS 10.5.4
    Linksys WRT54G v8.00.5
    SpeedStream DSL Modem
    I am having a strange issue. I am able to connect to my wireless network with my PowerBook and can see the Linksys setup page, but I cannot get on the internet. If I bypass the router I can get online with my PowerBook. If I use an ethernet cable connected to my Linksys I can get online with my PowerBook. My Sony Viao can connect wirelessly and get on the internet with no issue. My PlayStation 3 and PSP have no issues. It is solely this machine that is having the issue. I contacted Linksys and went through their troubleshooting to no avail.
    Does anyone have any idea as to what the issue may be, or what I can try to resolve this issue? I have done everything I can think of and no luck. Any ideas?

    Adam D wrote:
    I pinged 208.67.219.99 and the following was returned:
    PING 208.67.219.99 (208.67.219.99): 56 data bytes
    64 bytes from 208.67.219.99: icmp_seq=0 ttl=47 time=88.752 ms
    No error message was returned.
    I plugged the IP address into Safari and, although there were 27 errors, the page loaded. I hadn't tried that before. Interesting.
    The fact that the ping worked means you are connected to the Internet, and what is likely failing (causing the "You are not connected" message) is DNS name resolution.
    DNS name resolution is what converts names like "www.opendns.com" to numbers, like the numbers I gave above, 208.67.219.99.
    Changing your system to use the OpenDNS DNS servers, as directed above, will fix the name resolution issue on your system.

  • Anyone know the length of the power cable for the official dock for the K1?

    The power cable that came with the Ideapad K1 isn't long enough to reach my power strip behind my desk. I was wondering how long the power cable is for the dock that I see in the Lenovo store?
    Besides that, I love this tablet, nice and easy to hold, probably one of the most comfirtable tablets to hold (next to what Sony just released). I'm a little disappointed with the wifi connection and the reboots (down to maybe one today with the new launcher *sigh*). Even with the issues, I trust Lenovo more in terms of support then I do anyone else.

    Big Daddy, One other thing I forgot to mention is, If you open the case on your device, you'll instantly void any warranty that came with it. Also, bear in mind, any modifications that you make to the antenna system on this device could not only make the FCC approval that Linksys was given for the device null and void. Be very careful with anything like an antenna system on these devices, you can actually recieve RF burns if you contact any bare metal of the antenna system when it is transmitting. Just bear in mind that 2.4GHz is more less the same frequency that a microwave oven uses (although at a LOT lower power). As a radio ham, I've had the odd RF burn and I can tell you, they really hurt!.

  • Help! Extremely slow Internet speed using Linksys WRT54G router

    I have an eMac running OS 10.3.9 and wired to a Linksys WRT54G router using ethernet cable. I have to use this router for my work PC. I'm also using WildBlue satellite internet. The problem is, I'm getting about 1.5 Mbps on my PC, but less than 33 Kbps on my eMac. It was running faster before using dial-up. I've called WildBlue and Linksys tech support, and they can't help. Can anyone help?
    By the way, my son is using his iBook on the same router, only wireless, and he's happy with the speed he's getting compared to dial-up.
    Thanks,
    Eric

    1400 kbps is a lot nicer than 33 kbps, isn't it? You can possiblly tweak it a little more --- I know I've seen a MTU of 1460 mentioned --- since you can also revert back to the 1400 MTU setting you found.
    (Broadband Optimizer is in one sense a nice GUI to the terminal commnads you found and used.)
    One more thing to be aware of, satellite internet is subject to longer latency times than cable or DSL, due to the unavoidable geometry of bouncing data packets off a satellite in orbit. That could be an issue if you ever want to play real-time online multiplayer adventure type games. It shouldn't be an issue for being able to grab OS updates in minutes instead of hours, through. Enjoy your broadband access!

Maybe you are looking for