Linksys wvc54gca......trying to view with cellphone....need help

I have my linksys camera working with a motorola sbg900 router. I have everything setup and working fine except my rtsp to cell phone connection. I had it all properly setup on a netgear router and had to change over to the motorola. Here is some info... I have set a static ip, forwarded my cam ip, my rtsp 554-tcp, rtp 5000 udp and have set a passcode of 12345. On my phone i am trying rtsp://mycamname.linksys-cam.com/12345. Any suggestions? Any websites that offer remote assistance? Thanks

Heres how I got mine to work..
1.- DMZ all ports in the router to camera's IP. ( this si the option in which all traffic is allowed to go through, all ports open.)
2.- type rtsp:// xxx.xxx.xxx.xxx:1026/1234 ( where: xxx= Public IP address, 1026= port fo cell broadcast set in the camera's seup page and 1234 acces code in the same page.
3.- Make sure you have a rtsp capable phone, mine is a Balckberry bold, and type the above.If no luck at first, try clearing the cache from teh phone and powercycling it then re-try.
edusco, You should be carefull as to use the public address for rtsp instead of you home network as you did. you can check you public address in the router's page or by going to http://whatismyipaddress.com/
Good luck!!!

Similar Messages

I'm trying to install elements 12 need help?

I'm trying to install elements 12 need help?

What problem are you encountering in trying to install Elements 12?

Datasource connection with jboss, need help

Hi friends,
I am doing data source connection through Jboss (jboss-4.0.2) with mysql database. I am using java(j2sdk1.4.2_04). I have made all changes given in this link -- http://community.jboss.org/wiki/SetUpAMysqlDatasource
After making changes I restart jboss properly, but when I am going to attempt to connection through class. it give following error.
1.ERROR! Shared library ioser12 could not be found.
Can't find SerialContextProvider
When a create a diffrent new class, then give me this error.
2. ERROR! Shared library ioser12 could not be found.
Cannot get connection: javax.naming.CommunicationException: Can't find SerialContextProvider
Kindly help me out for this problem.
Thanks
Abhishek Jain

user13428037 wrote:
,,, JBoss ... give following error.
1.ERROR! Shared library ioser12 could not be found.
Can't find SerialContextProvider
When a create a diffrent new class, then give me this error.
2. ERROR! Shared library ioser12 could not be found.
Cannot get connection: javax.naming.CommunicationException: Can't find SerialContextProviderPlease don't crosspost http://www.javaprogrammingforums.com/jdbc-databases/6353-datsource-connection-mysql-need-help.html#post22533
The
ERROR! Shared library ioser12 could not be found.error message has nothing to do with you adding a datasource.
It would happen even before you made the datasource configuration changes.
Looks like you added a j2ee.jar to the JBoss classpath.

When trying to view Apps that need updates, it says cannot connect to iTunes store..... My wifi is working fine so I'm not sure what the problem is.... Help pls!

Apps

Go to Settings>General>Date & Time and change the date to a few months in the future and then re-try.

Getting started with C# need help to know what I need to learn

Good evening everybody, first time posting in this forum, so be gentle with my lack of knowledge about C#.
A bit about me first, I'm a electronics student, with a strong C/C++ knowledge but geared toward micro-controllers(namely AVR's, PSoC and ARM Cortex-M3), now I want to make some nice GUI's for some electronic widgets and my main OS is Windows and
C# seems to fit the bill for what I need to do, that is basic GUI's, serial com's and some graphing features do display simples x/y graphs.
So, I'm in the process of designing a two stroke ignition system and I want to make a easy to use interface to re-program and visualize the ignition curve and some other parameters, so a simples program I think.
My main idea/design is more or like the program made by the Ignitech company, I will post some example images so I can explain my self better.
The first picture shows the principal window for me, its a simple graph that is driven by the two tables that are over th graph, I would prefer to have a dynamic table(for example show only 8 positions or 10 ou 12, driven by another input box), and then
the graph, and a couple tabs, in part so I can configure multi-curve ignitions, and to have a couple different "main" tabs, main configuration, the advance designer tab and a monitor tab(shown in the second picture).
What I'm seeking is what functions/methods should I study and use to achieve this?
I think I should say that I'm not copying anything from Ignitech, much less trying to make a "pirate" version of their software(its a free direct download from their site), its just a personal project.
Best regards and thanks in advance.
EDIT: For now I cannot post pictures(and links I assume), hope you guys and girls can get the mental image.

Hi
Keeepcool,
I am sorry to tell you that this forum is only covering the C# programming language, IDE, libraries, samples, and tools. Since your issue is not clear to us. I will move your thread to "off-topic " forum. If you have any others issues about C#,
Please feel free to post in this forum. Thanks for your understading.
Best Wishes!
Kristin
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Trying to delete "submit" button. Tried unsucessfully 5 times. Need help and want to start over.

I created a pdf that I just wanted people to be able to fill in, download, print out and then mail to me. I followed the instructions from a previous acrobat expert who replied to me yesterday and that did not work. Now, I've tried this 5 times and the system has blocked me out unless I pay for your advanced system which is $143. Please help
Re: Want to delete the "submit" link on a pdf
created by Lucia Lao in FormsCentral - View the full discussion
Hi,
I believe this is a form that you created with FormsCentral and then you downloaded/saved as PDF via the "Save Submission-Enabled PDF" button via the Distribute Tab.
Please select via FormsCentral app main menu:
- File -> Save As PDF Form... and then
- when you get the dialog "Would you like your PDF form to collect responses online in the "View Responses" tab?" select "Don't Collect Responses" button.
This will save the PDF form without the Submit button/link.
Thanks,
Lucia
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/5218029#5218029
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: [http://forums.adobe.com/message/5218029#5218029]
To unsubscribe from this thread, please visit the message page at [http://forums.adobe.com/message/5218029#5218029]. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in FormsCentral by email or at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

The instructions Lucia gave you were correct. It seems you have a Basic trial account (5 forms). You can just delete the forms you are not using so you can create more. Can you explain in more detail how those instructions above didn't work? I think there is some confusion so any details you can provide will help clear it up.
Randy

Error message, 0xE8000065 when trying to sync with iTunes. HELP!!!

I bought a new iPhone 4S, but when I try to connect it to iTunes, I get an error message, 0xE8000065, or sometimes 0xE800001. I want to sync it but nothing I've tried (restarting the services, restarting the machine, reinstalling iTunes, erasing lockdown folder) works. Can anyone help me?
P.S. I saw a video in youtube explaining how to try to connect it using recovery mode, and iTunes did in fact detect the iPhone and asked me to update and restore. I did not want to as I already have some apps and pics but I went through it anyway. Since it was taking a LONG time, I went to get something to eat: when I came back, the iPhone had not been restored, and it still wouldn't connect to iTunes. I'm guessing the restore/update failed? In any case, how can I fix this issue?

"itunes could not connect with the itunes store. An unknown error occurred (11556)."
This error is associated with ringtones, are you trying to sync a ringtone, purchase a ringtone...need more info...
I have also an error message saying it cannot sync and error message number 0050.
Are you on Windows XP? Is this the error message...iTunes displays -50 error message? If so, follow these directions:
http://support.apple.com/kb/TS1539

Problem with routing - Need help

Hello,
I need a little direction with what I think is a routing problem. Any help will be appreciated. My setup is as follows:
Cable Modem
27.177.21.9
WAN - Gi0/0
27.177.21.10
Cisco 2901
LAN - Gi0/1
192.168.1.250
Client
192.168.1.10
The Problem
Router can ping LAN interface
Router cannot ping WAN interface -X
Router can ping Cable Modem
Client
Client can ping LAN interface
Client can ping WAN interface
Client cannot ping Cable Modem -X
Here is my routing table:
Gateway of last resort is 27.177.21.9 to network 0.0.0.0 (this is my cable modem)
S* 0.0.0.0/0 [1/0] via 27.177.21.9
is directly connected, GigabitEthernet0/0
27.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 27.177.21.8/30 is directly connected, GigabitEthernet0/0
L 27.177.21.10/32 is directly connected, GigabitEthernet0/0
192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.1.0/24 is directly connected, GigabitEthernet0/1
L 192.168.1.250/32 is directly connected, GigabitEthernet0/1
Here is a portion of my configuration:
interface GigabitEthernet0/0
description Cable Internet$FW_OUTSIDE$$ETH-WAN$
ip address 27.177.21.10 255.255.255.252
zone-member security out-zone
duplex auto
speed auto
interface GigabitEthernet0/1
description hbc_staff$FW_INSIDE$$ETH-LAN$
ip address 192.168.1.250 255.255.255.0
zone-member security in-zone
duplex auto
speed auto
no mop enabled
ip default-gateway 27.177.21.9
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
ip route 0.0.0.0 0.0.0.0 27.177.21.9
ip route 192.168.1.0 255.255.255.0 27.177.21.9
Thanks in advance

Hello Jon,
I continue to try different configurations to get my router to connect without success. I am now trying NAT and this is where we stand now. Any help will be much appreciated.
The problem
Router now pings everything by ip address or name
Client PC from inside the LAN cannot ping modem or Internet
Relevant parts of configuration:
ip domain name mydomain.org
ip name-server 24.247.15.53
ip name-server 66.189.0.100
interface GigabitEthernet0/0
description Internet$FW_OUTSIDE$ETH-WAN$
ip address 27.177.21.10 255.255.255.252
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface GigabitEthernet0/1
description hbc_staff$FW_INSIDE$$ETH-LAN$
ip address 192.168.1.250 255.255.255.0
ip nat inside
ip virtual-reassembly in
zone-member security in-zone
duplex auto
speed auto
no mop enabled
ip nat pool HBC-I 27.177.21.10 27.177.21.10 prefix-length 24
ip nat inside source list 7 pool HBC-I overload
ip route 0.0.0.0 0.0.0.0 27.177.21.9
ip route 192.168.1.0 255.255.255.0 GigabitEthernet0/1
access-list 7 permit 192.168.1.0 0.0.0.255
#show ip route
Gateway of last resort is 27.177.21.9 to network 0.0.0.0
S* 0.0.0.0/0 [1/0] via 27.177.21.9
27.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 27.177.21.8/30 is directly connected, GigabitEthernet0/0
L 27.177.21.10/32 is directly connected, GigabitEthernet0/0
192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.1.0/24 is directly connected, GigabitEthernet0/1
L 192.168.1.250/32 is directly connected, GigabitEthernet0/1
When pinging the modem from a client inside the LAN this is what I get from NAT translations and statistics:
#sho ip nat translations ver
Pro Inside global Inside local Outside local Outside global
icmp 27.177.21.10:40709 192.168.1.8:40709 27.177.21.9:40709 27.177.21.9:40709
create 00:00:05, use 00:00:00 timeout:60000, left 00:00:59, Map-Id(In): 1,
flags:
extended, use_count: 0, entry-id: 4, lc_entries: 0
#sho ip nat statistics
Total active translations: 2 (0 static, 2 dynamic; 2 extended)
Peak translations: 2, occurred 00:00:04 ago
Outside interfaces:
GigabitEthernet0/0
Inside interfaces:
GigabitEthernet0/1
Hits: 104 Misses: 0
CEF Translated packets: 104, CEF Punted packets: 0
Expired translations: 7
Dynamic mappings:
-- Inside Source
[Id: 1] access-list 7 pool HBC-I refcount 2
pool HBC-I: netmask 255.255.255.0
start 27.177.21.10 end 27.177.21.10
type generic, total addresses 1, allocated 1 (100%), misses 0
Total doors: 0
Appl doors: 0
Normal doors: 0
Queued Packets: 0

New beginner with iTunes need help please!!

When i am trying to open iTunes this is the message that has been brought up has anyone had the same problem and who knows how i could fix this problem??
Error Signature
AppName: itunes.exe AppVer:7.0.2.16 ModName: unknown
Reporting Details
This error report includes; information regarding the condition of iTunes when the problem occurred the operating system version and computer hardware in use; Digital Product ID, which could be used to identify your license and the Internet Protocol (IP) address of your computer
We do not intentionally collect your files, name and address or any form of personally identifiable information. Etc etc
Windows XP

Dougal95 wrote:
The list doesn't say which one is in which format.
IN the iTunes menu, click on View, then View Options, and check the "Kind" box. This will display the Kind for each track. if it says "MPEG Audio File," it's an MP3.
Should all my MP3 files be converted to simplify things.
No need to convert any music. iTunes can play MP3s.

Frustrated with upgrade - NEED HELP

I had a problem on my PowerBook PowerPC G4 when I updated to Safari 3.1.1
Safari, Mail and the Software update would no longer run.
Tried everything to no avail.
Did an archive system install back to 10.4.6
Now I am unable to update to 10.4.11
I downloaded the Installer Package and when I run it I get the prompt:
"You cannot install Mac OS X Update (PowerPC) on this volume.
This volume does not meet the requirements for this update."
What am I doing wrong?

Here's another suggestion that will help in the future:
Basic Backup
Get an external Firewire drive at least equal in size to the internal hard drive and make (and maintain) a bootable clone/backup. You can make a bootable clone using the Restore option of Disk Utility. You can also make and maintain clones with good backup software. My personal recommendations are (order is not significant):
1. Retrospect Desktop (Commercial - not yet universal binary)
2. Synchronize! Pro X (Commercial)
3. Synk (Backup, Standard, or Pro)
4. Deja Vu (Shareware)
5. PsynchX 2.1.1 and RsyncX 2.1 (Freeware)
6. Carbon Copy Cloner (Freeware - 3.0 is a Universal Binary)
7. SuperDuper! (Commercial)
8. Intego Personal Backup (Commercial)
9. Data Backup (Commercial)
The following utilities can also be used for backup, but cannot create bootable clones:
1. Backup (requires a .Mac account with Apple both to get the software and to use it.)
2. Toast
3. Impression
4. arRSync
Apple's Backup is a full backup tool capable of also backing up across multiple media such as CD/DVD. However, it cannot create bootable backups. It is primarily an "archiving" utility as are the other two.
Impression and Toast are disk image based backups, only. Particularly useful if you need to backup to CD/DVD across multiple media.
Visit The XLab FAQs and read the FAQs on maintenance, optimization, virus protection, and backup and restore. Also read How to Back Up and Restore Your Files.
Although you can buy a complete FireWire drive system, you can also put one together if you are so inclined. It's relatively easy and only requires a Phillips head screwdriver (typically.) You can purchase hard drives separately. This gives you an opportunity to shop for the best prices on a hard drive of your choice. Reliable brands include Seagate, Hitachi, Western Digital, Toshiba, and Fujitsu. You can find reviews and benchmarks on many drives at Storage Review.
Enclosures for FireWire and USB are readily available. You can find only FireWire enclosures, only USB enclosures, and enclosures that feature multiple ports. I would stress getting enclosures that use the Oxford chipsets (911, 921, 922, for example.) You can find enclosures at places such as;
Cool Drives
OWC
WiebeTech
Firewire Direct
California Drives
NewEgg
All you need do is remove a case cover, mount the hard drive in the enclosure and connect the cables, then re-attach the case cover. Usually the only tool required is a small or medium Phillips screwdriver.

Preparing to travel with LR -- Need Help

Have clone/copied all my LR files (catalog, etc. and photo files) from the external drive on which they regularly reside onto a smaller, traveling HD. But iin opening LR from that Traveling Drive, I am faced with all those frustrating question marks signifiying missing or offline files. Trying to have the program find the missing files has been unavailing. What should I have done and what do I need to do? Would greatly appreciate someone walking me through this.
Thanks.
jack

If the copy indeed follows the original, you should be able to connect up the top level folder, by showing LR the new path where said folder now resides. Control or Alt click on it to bring up the dialog.

Need help with iPhoto, Need help with iPhoto

Hey there!!!
When I plug in my iPhone I go to iPhoto and can choose to import the pictures. I also tried Image Capture as it seemed easier to organise my pictures, making folders, sub-folders, etc. The problem with this is everytime I plug my iPhone into the computer click on Import the system automatically makes second, third, fourth, etc copies of each picture. This also means that there is a copy of my pictures on iPhoto and on Image Capture - which I do not really need.
I have tried to make Albums and Folders on iPhoto. Sometimes when I delete a picture as it has been saved in two albums it gets deleted from both albums. Why is this? How can I make Albums or Folders to organise my pictures. If my pictures are transferred directly onto iPhoto, can I find them anywhere else in my computer? If I wanted to burn pictures from various albums on a disc how could I do that on iPhoto? Also I dont want events to create themselves. How can I avoid this?
I would like help with either using iPhoto or know how the stop the duplicating of pictures on Image Capture.
Maybe there is a better way I can transfer the pictures onto my MacBook??
Thanks a mil!!!

Are you running a "referenced" or "managed' library?
Image Capture does not store phortos in it. It's an application for uploading photos to wherever you tell it to, either a folder on the hard drive or into iPhoto. If you want to use only Image Capture to upload your photos to iPhoto then set iPhoto's General preferences to the following:
Deleting Photos from an iPhoto Library:
1 - from an Event or the Photos mode: select the photo(s) and use the Delete key to move the photos to the trash bin. Then empty the iPhoto Trash bin as follows:
2 - from an album, smart album, book, slideshow, card, etc.: select the photo(s) and use the key combination of Command+Option+Delete to move the photos to the trash bin. Then empty the trash bin as above.
NOTE: deleting a photo from an album, slideshow, book, etc., with only the Delete key only deletes that photo from that item. Deleting a photo from an Event deletes ALL occurances of that photo in the library.
OT

Trying to activate cs6 and need help please

i just spent an hour with this dude in india trying to activate cs6 production premium academic
i am trying to 'offline' activate my editing rig because it's too heavy to move to internet
also i installed the trial version of cs6 production premium
and tried to activate that with the academic serial numbers (because it installed correctly and the updates, too)
i got the REQUEST code: when you type it into the activation page do you use the spacebar between each set of 4 characters?
are the 0's upper case letter o's or are they zeros?
we tried all sorts of combinations and nothing works so i'm supposed to wait 4-5 hours until licensing/activation people get into the office...
does anyone have any help or advice on this please?
thanks again,
j

>editing rig because it's too heavy to move to internet
Since there have been bug fix updates, you will need to get the update files to your computer
Either by using a different computer and a USB flash drive, or by buying a LONG network cable
All Adobe updates start here and select product, read to see if you need to install updates in number order, or if the updates are cumulative for the individual product http://www.adobe.com/downloads/updates/

ISM with NAT44 - Need help with configuration

Hello everyone,
I'm trying to set up NAT44 in the following scenario below and I'm having a hard time figuring out how to redirect the traffic. As you can see the big problem is that I have one single interface that connects to the internal network (10.0.0.0/8) and also to the tunnel destinations all in the same VRF. Can you guys give me a hand? The trafiic comes from network network 10.0.0.0/8 enters interface bundle-ether 2 (Now it needs to be translated), once it is translated, now it needs to reach the destination known via GRE tunnel.
Configurations
vrf NAT_IN
address-family ipv4 unicast
vrf BLUE
address-family ipv4 unicast
hw-module service cgn location 0/3/CPU0
interface Bundle-Ether2
description UPLINK TO METRO ETHERNET
interface Bundle-Ether2.2 l2transport
encapsulation dot1q 2
rewrite ingress tag pop 1 symmetric
interface GigabitEthernet200/0/0/43
description LINK TO METRO ETHERNET
bundle id 2 mode active
interface GigabitEthernet300/0/0/43
description LINK TO METRO ETHERNET
bundle id 2 mode active
interface BVI2
description METRO
vrf BLUE
ipv4 address 100.0.0.10/24
interface tunnel-ip 101
description GRE_TUNNEL
vrf BLUE
ipv4 address 1.1.1.1/32
tunnel mode gre ipv4
tunnel source interface bvi 2
tunnel destination 200.0.0.1
interface BVI 100
vrf BLUE
ipv4 address [GATEWAY_100] [MASK_100]
interface BVI 200
vrf BLUE
ipv4 address [GATEWAY_200] [MASK_200]
interface BVI 300
vrf BLUE
ipv4 address [GATEWAY_300] [MASK_300]
interface ServiceApp1
vrf NAT_IN
ipv4 address 10.0.2.1 255.255.255.252
service cgn CGN service-type nat44
interface ServiceApp2
vrf BLUE
ipv4 address 10.0.2.2 255.255.255.252
service cgn CGN service-type nat44
interface ServiceInfra1
ipv4 address 10.0.3.1 255.255.255.0
service-location 0/3/CPU0
router static
address-family ipv4 unicast
vrf NAT_IN
address-family ipv4 unicast
0.0.0.0/0 ServiceApp1
10.0.0.0/8 vrf BLUE bvI 2 <NEXT HOP>
vrf BLUE
address-family ipv4 unicast
172.16.0.0/24 ServiceApp2
router ospf METRO
vrf BLUE
router-id [ROUTER_ID]
redistribute bgp 65500 metric 100
area 0
interface bvi 2
router ospf BLUE
vrf BLUE
router-id [ROUTER ID]
redistribute bgp 65500 metric 100
area 10
interface BVI100
interface BVI200
interface BVI200
router bgp 65500
address-family ipv4 unicast
address-family vpnv4 unicast
vrf BLUE
rd 65500:2
address-family ipv4 unicast
redistribute static
redistribute ospf BLUE
neighbor 1.1.1.2
remote-as 64512
ebgp-multihop 5
address-family ipv4 unicast
route-policy PASS in
route-policy PASS out
service cgn CGN
service-location preferred-active 0/3/CPU0
service-type nat44 nat44
portlimit 20000
inside-vrf NAT_IN
map outside-vrf BLUE address-pool 172.16.0.0/24
Thanks in advance,
Renato

Hi Somnath,
Let's see if you can help with this new scenario. I want to extend this NAT configuration to a new site (BO1), but instead of using this entire setup with ASR9K, etc, I just want to use ASR9000v module and have this AS9K + ISM as the host. The first problem I see in this scenario is that I have the same 10.0.0.0/8 network in both sites, network which will access the same resources as the devices in the 10.0.0.0/8 in the main site.
1) Do you think if I create a new inside VRF [NAT_IN1] would address this issue?
2) Can I use the same outside VRF?
Here is the configurations.
!! IOS XR Configuration 4.3.1
vrf NAT_IN
address-family ipv4 unicast
import route-target
   65500:2
   65500:3
export route-target
   65500:3
vrf RED
address-family ipv4 unicast
import route-target
   65500:1
export route-target
   65500:1
vrf NAT_OUT
address-family ipv4 unicast
import route-target
   65500:4
export route-target
   65500:4
vrf SATELLITE
vrf BLUE
address-family ipv4 unicast
import route-target
   65500:2
export route-target
   65500:2
hw-module service cgn location 0/3/CPU0
ipv4 access-list ABF
5 permit ospf any any
10 permit ipv4 any 10.200.0.0 0.0.255.255 nexthop1 vrf NAT_IN ipv4 10.0.2.2
20 permit icmp any any
interface Bundle-Ether3
description Uplink (BE3 - VRF NAT_IN) - VLAN 20
vrf NAT_IN
ipv4 address 1.1.1.1 255.255.255.0
ipv4 access-group ABF ingress
interface Bundle-Ether22
description LOOPBACK CABLE NAT_OUT
vrf NAT_OUT
ipv4 address 10.0.1.1 255.255.255.0
interface Bundle-Ether23
description LOOPBACK CABLE BLUE
vrf BLUE
ipv4 address 10.0.1.2 255.255.255.0
interface 6
description Uplink (BE6 - Global) - VLAN 20,51,80-82
interface 6.2
ipv4 address 1.1.1.2 255.255.255.0
encapsulation dot1q 2
interface 6.51 l2transport
description EFP - BE6 - VLAN 51
encapsulation dot1q 51
rewrite ingress tag pop 1 symmetric
interface 6.80 l2transport
description EFP - BE6 - VLAN 80
encapsulation dot1q 80
rewrite ingress tag pop 1 symmetric
interface 6.81 l2transport
description EFP - BE6 - VLAN 81
encapsulation dot1q 81
rewrite ingress tag pop 1 symmetric
interface 6.82 l2transport
description EFP - BE6 - VLAN 82
encapsulation dot1q 82
rewrite ingress tag pop 1 symmetric
interface Bundle-Ether100
description Bundle to Satellite 100
vrf SATELLITE
ipv4 point-to-point
ipv4 unnumbered Loopback0
nv
satellite-fabric-link satellite 100
   remote-ports GigabitEthernet 0/0/0-43
interface Bundle-Ether200
description Bundle to Satellite 200
vrf SATELLITE
ipv4 point-to-point
ipv4 unnumbered Loopback0
nv
satellite-fabric-link satellite 200
   remote-ports GigabitEthernet 0/0/0-43
interface Bundle-Ether300
description Bundle to Satellite 300
vrf SATELLITE
ipv4 point-to-point
ipv4 unnumbered Loopback0
nv
satellite-fabric-link satellite 300
   remote-ports GigabitEthernet 0/0/0-35
interface Loopback0
description MGMT SATELLITE
vrf SATELLITE
ipv4 address 10.0.0.254 255.255.255.0
interface tunnel-ip31101
description BLUE-TUNNEL01
vrf BLUE
ipv4 address 10.200.253.90 255.255.255.252
tunnel mode gre ipv4
tunnel source 6.2
tunnel destination 13.13.13.13
interface tunnel-ip31102
description BLUE-TUNNEL02
vrf BLUE
ipv4 address 10.200.253.94 255.255.255.252
tunnel mode gre ipv4
tunnel source 6.2
tunnel destination 14.14.14.14
interface tunnel-ip31103
description RED-TUNNEL03
vrf RED
ipv4 address 10.200.253.90 255.255.255.252
tunnel mode gre ipv4
tunnel source 6.2
tunnel destination 13.13.13.13
interface tunnel-ip31104
description RED-TUNNEL04
vrf RED
ipv4 address 10.200.253.94 255.255.255.252
tunnel mode gre ipv4
tunnel source 6.2
tunnel destination 14.14.14.14
interface TenGigE0/0/0/0
description LINK TO SATELLITE 100
bundle id 100 mode on
interface TenGigE0/0/0/1
description LINK TO SATELLITE 100
bundle id 100 mode on
interface TenGigE0/0/0/2
description LINK TO SATELLITE 200
bundle id 200 mode on
interface TenGigE0/0/0/3
description LINK TO SATELLITE 200
bundle id 200 mode on
interface TenGigE0/0/0/4
description LINK TO SATELLITE 300
vrf SATELLITE
ipv4 point-to-point
ipv4 unnumbered Loopback0
nv
satellite-fabric-link satellite 300
   remote-ports GigabitEthernet 0/0/36-43
interface TenGigE0/0/0/5
description LINK TO SATELLITE 300
bundle id 300 mode on
interface TenGigE0/0/0/16
description UPLINK (BE6 - GLOBAL) - VLAN 20,51,80-82
bundle id 6 mode active
interface TenGigE0/1/0/16
description UPLINK (BE6 - GLOBAL) - VLAN 20,51,80-82
bundle id 6 mode active
interface TenGigE0/0/0/17
description UPLINK (BE3 - VRF NAT_IN) - VLAN 20
bundle id 3 mode active
interface TenGigE0/1/0/17
description UPLINK (BE3 - VRF NAT_IN) - VLAN 20
bundle id 3 mode active
interface TenGigE0/0/0/22
description LOOPBACK CABLE TE0/1/0/22
bundle id 22 mode on
interface TenGigE0/0/0/23
description LOOPBACK CABLE TE0/1/0/23
bundle id 22 mode on
interface TenGigE0/1/0/0
description LINK TO SATELLITE 100
bundle id 100 mode on
interface TenGigE0/1/0/1
description LINK TO SATELLITE 100
bundle id 100 mode on
interface TenGigE0/1/0/2
description LINK TO SATELLITE 200
bundle id 200 mode on
interface TenGigE0/1/0/3
description LINK TO SATELLITE 200
bundle id 200 mode on
interface TenGigE0/1/0/4
description LINK TO SATELLITE 300
bundle id 300 mode on
interface TenGigE0/1/0/5
description LINK TO SATELLITE 300
bundle id 300 mode on
interface TenGigE0/1/0/22
description LOOPBACK CABLE TE0/0/0/22
bundle id 23 mode on
interface TenGigE0/1/0/23
description LOOPBACK CABLE TE0/0/0/23
bundle id 23 mode on
interface BVI30
vrf RED
ipv4 address 10.200.25.193 255.255.255.192
interface BVI31
vrf BLUE
ipv4 address 10.200.1.1 255.255.255.248
interface BVI32
vrf BLUE
ipv4 address 10.200.25.129 255.255.255.224
interface BVI33
vrf BLUE
ipv4 address 10.200.25.1 255.255.255.128
interface BVI36
vrf BLUE
ipv4 address 10.200.237.145 255.255.255.240
interface BVI51
vrf RED
ipv4 address 192.168.7.12 255.255.255.0
interface BVI80
vrf RED
ipv4 address 10.200.26.169 255.255.255.224
interface BVI81
vrf BLUE
ipv4 address 10.200.25.164 255.255.255.240
interface BVI82
vrf BLUE
ipv4 address 10.200.25.180 255.255.255.240
interface ServiceApp1
description NAT_IN
vrf NAT_IN
ipv4 address 10.0.2.1 255.255.255.252
service cgn CGN service-type nat44
interface ServiceApp2
description NAT_OUT
vrf NAT_OUT
ipv4 address 10.0.2.5 255.255.255.252
service cgn CGN service-type nat44
interface ServiceInfra1
description ISM
ipv4 address 10.0.3.1 255.255.255.0
service-location 0/3/CPU0
prefix-set PS_ROUTES
10.200.0.8,
10.200.5.40/29,
10.200.1.0/29,
10.200.5.32/29,
10.200.0.144/28,
10.200.106.0/28,
10.200.106.16/28
end-set
prefix-set PS_BGP_BLUE_OUT
10.200.24.192/26,
10.200.5.40/29,
10.200.240.0/25,
10.200.1.0/29,
10.200.25.128/27,
10.200.25.0/25,
10.200.5.32/29,
10.200.26.0/25,
10.200.0.144/28,
10.200.27.128/27,
10.200.27.0/25,
10.200.106.0/28,
10.200.106.128/25,
10.200.106.16/28,
10.200.107.128/25
end-set
route-policy RP_DENY_ALL
drop
end-policy
route-policy RP_PASS_ALL
pass
end-policy
route-policy RP_BGP_BLUE_OUT
if destination in PS_BGP_BLUE_OUT then
    pass
endif
end-policy
route-policy RP_PASS_ROUTES
if destination in PS_ROUTES then
    pass
endif
end-policy
router static
address-family ipv4 unicast
0.0.0.0/0 1.1.1.20
vrf NAT_IN
address-family ipv4 unicast
   0.0.0.0/0 ServiceApp1
vrf RED
vrf NAT_OUT
address-family ipv4 unicast
   0.0.0.0/0 10.0.1.2
   10.200.24.192/26 ServiceApp2
vrf BLUE
address-family ipv4 unicast
   10.200.24.192/26 10.0.1.1
router ospf
log adjacency changes
vrf NAT_IN
router-id 1.1.1.1
disable-dn-bit-check
redistribute bgp 65500 metric 5 metric-type 2 route-policy RP_PASS_ROUTES
area 7
   interface Bundle-Ether3
router ospf RED
log adjacency changes
vrf RED
router-id 10.200.26.169
disable-dn-bit-check
redistribute bgp 65500 metric 10 metric-type 2
area 11
   interface BVI30
   interface BVI80
router ospf BLUE
log adjacency changes
vrf BLUE
router-id 10.200.25.164
disable-dn-bit-check
redistribute static
redistribute bgp 65500 metric 10 metric-type 2
area 0
   interface BVI81
   interface BVI82
area 2
   interface BVI31
   interface BVI32
   interface BVI33
   interface BVI36
router bgp 65500
address-family ipv4 unicast
address-family vpnv4 unicast
vrf NAT_IN
rd 65500:3
bgp router-id 1.1.1.1
address-family ipv4 unicast
   route-target download
vrf RED
rd 65500:1
bgp router-id 10.200.253.90
address-family ipv4 unicast
   network 10.200.25.192/26
   network 10.200.26.128/27
   network 10.200.26.192/27
   network 10.200.27.192/26
   network 10.200.104.128/27
   network 10.200.104.160/27
neighbor 10.200.253.89
   remote-as 64512
   ebgp-multihop 5
   update-source tunnel-ip31103
   address-family ipv4 unicast
    route-policy RP_PASS_ALL in
    route-policy RP_PASS_ALL out
    soft-reconfiguration inbound
neighbor 10.200.253.93
   remote-as 64512
   ebgp-multihop 5
   update-source tunnel-ip31104
   address-family ipv4 unicast
    route-policy RP_PASS_ALL in
    route-policy RP_PASS_ALL out
    soft-reconfiguration inbound
vrf BLUE
rd 65500:2
bgp router-id 10.200.253.90
address-family ipv4 unicast
   network 10.200.0.144/28
   network 10.200.1.0/29
   network 10.200.5.32/29
   network 10.200.5.40/29
   network 10.200.24.192/26
   network 10.200.25.0/25
   network 10.200.25.128/27
   network 10.200.26.0/25
   network 10.200.27.0/25
   network 10.200.27.128/27
   network 10.200.106.0/28
   network 10.200.106.16/28
   network 10.200.106.128/25
   network 10.200.107.128/25
   network 10.200.240.0/25
neighbor 10.200.253.89
   remote-as 64512
   ebgp-multihop 5
   update-source tunnel-ip31101
   address-family ipv4 unicast
    route-policy RP_PASS_ALL in
    route-policy RP_BGP_BLUE_OUT out
    soft-reconfiguration inbound
neighbor 10.200.253.93
   remote-as 64512
   ebgp-multihop 5
   update-source tunnel-ip31102
   address-family ipv4 unicast
    route-policy RP_PASS_ALL in
    route-policy RP_BGP_BLUE_OUT out
    soft-reconfiguration inbound
l2vpn
load-balancing flow src-dst-ip
bridge group VLAN30
bridge-domain VLAN30
   routed interface BVI30
bridge group VLAN31
bridge-domain VLAN31
   routed interface BVI31
bridge group VLAN32
bridge-domain VLAN32
   routed interface BVI32
bridge group VLAN33
bridge-domain VLAN33
   routed interface BVI33
bridge group VLAN36
bridge-domain VLAN36
   routed interface BVI36
bridge group VLAN51
bridge-domain VLAN51
   routed interface BVI51
bridge group VLAN80
bridge-domain VLAN80
   interface 6.80
   routed interface BVI80
bridge group VLAN81
bridge-domain VLAN81
   interface 6.81
   routed interface BVI81
bridge group VLAN82
bridge-domain VLAN82
   interface 6.82
   routed interface BVI82
nv
satellite 100
type asr9000v
ipv4 address 10.0.0.1
satellite 200
type asr9000v
ipv4 address 10.0.0.2
satellite 300
type asr9000v
ipv4 address 10.0.0.3
service cgn CGN
service-location preferred-active 0/3/CPU0
service-type nat44 nat44
portlimit 20000
inside-vrf NAT_IN
   map outside-vrf NAT_OUT address-pool 10.200.24.192/26
Thanks in advance,
Renato

Leopard Wireless Dropouts - Tried all reccomended forum fixes - need help

I need to add my name to the list of people who are having genuine problems with the wireless networking in leopard. I am the primary systems admin for a school, and responsible for maintaining an install base of over 250 intel macbooks. Since upgrading to leopard we have had many many wireless issues.
We have 3com wx1200 wireless controllers running numerous 3com 3750 and 2750 access points. The security is WPA2 with PSK authentication (though I can shut the security right off without any improvements in reliability). Macbooks will consistantly drop the connection to the wireless requiring a "turn airport off" and "turn airport on" to re-establish the connection, which works about half of the time.... Many times the machines need to be rebooted. It seems as though our original core duo macbooks are the most affected, though the problem exists on all our macbooks running leopard. (currently 10.5.5) *Rebuilding any of the affected laptops with tiger instantly clears up any problems*. No tiger machines, and no windows machines have any issues with the connection drops. I've tried every documented suggested fix on the numerous other threads here where people are having this exact same issue. I've eliminated all the variables and my problem seems to be leopard alone, or perhaps leopard in conjuction with this particular wireless infrastructure. Regardless, it's time that this problem is officially acknowledged and that some strides are made to remedy it. I'd be very happy and available to work with apple engineers on this problem. I can provide whatever logs or dumps you need.
This is one of two unacknowledged widespread issues that is shooting us in the foot. We are also plagued by the problem where faulty parental controls partially restrict access to secure sites (in our case google docs). This bug is also all over the forums and goes unresolved.
Any ideas or suggestions (other than permissions repairs, keychain repairs, and upgrading router firmware - it's all been done!) would be most appreciated!
Cheers,
Neil

These are actually user to user forums - a place for fellow Mac users to get together and swap troubleshooting ideas.
However Apple Engineering does not read these boards on an official basis, so we can complain about something all day but until it makes its way through AppleCare to engineering it won't get on the engineers' work queues.
The other way to file a bug is to register for a free Apple Developer Connection Online account, which will then allow you to file bugs via the Apple Bug Reporter.

Linksys wvc54gca......trying to view with cellphone....need help

Similar Messages

Maybe you are looking for