Linux for K7N2 Delta-ILSR

Hello,
Does anyone know of with Linux distro is compatible with the K7N2 Delta Series?
Sincerely, Deft

Knoppix worked too, even my TvTuner worked.
Not that I would recommend Knoppix as a solution, I was just playing.
There is a lot more support for the nvidia kit now.

Similar Messages

AGP Setup For k7n2 delta ilsr

I have a k7n2 delta ilsr mb, in display properties on desk top setting tab then advanced button then GeForce tab under adapter information is Bus and memory. To the right of Bus it reads AGP (PCI mode) shouldn't that read AGP (8X), how can I change this. Ron.

Hi,
No, leave it at 64 or 128.
Go here for an explanation:
http://www.rojakpot.com/default.aspx?location=7&var1=18
Then - Click on: "Free Access To the BIOS Optimization Guide" near the bottom of the page - then click on "AGP Aperture Size"
Axel

Need help with jumper settings for k7n2 delta ilsr

I have a k7n2 delta ilsr and I'm using a AMD 2800+ barton 333 fsb. I'm not sure what the jumper settins are for this cpu. The users guide only shows 133/166 and 200, can anyone help me with the jumper settings.
Thanks, Ron.

Hi,
As your processor is 333FSB - the jumper should be set to 166FSB as should the BIOS. As your RAM CPU combination runs at 2x166=333 or thereabouts.
Basically, as a general rule, if you halve the FSB speed of your processor you'll get the setting for both BIOS and Jumper. 200FSB=100, 266FSB=133, 333FSB=166 etc. etc.
Axel

Kingston HyperX Memory for K7N2 Delta-ILSR

Hey will my K7N2 Delta-ILSR support the Kingston HyperX serises DDR400-512MB Ram?
Im looking to buy 2 maybe 3 of these and really want to be sure theyll work.
http://www.ec.kingston.com/shop/partsinfo.asp?ktcpartno=KHX3200A/256&promo=hx2shp
I checked the supported ram list for the K7N2 Delta-ILSR and they wernt on there so i just figured it may be out of date?
So thanx in Advance for info!
p.s. It will support 3x 512MB right?

Has anyone noticed how the Hyper X went from the poor-man's Corsair to being priced equal to OCZ, and usually higher then Geil, as well as usually being very close to Corsair, if not the same? I think only Mushkin beats it out now price-wise...

New Modded BIOS for K7N2 Delta ILSR

MSI K7N2 Delta ILSR Modded BIOS based on Official v. 7.80 BIOS
download here:

Description: Access through interface which is on insecure interfaces list detected. Request aborted.
Interface/Client IP address:
Date: Wed, 18 May 2005 13:11:17 GMT
Doesn't work for me
By the way did u put the bios to vork with 1.3 vcore like the braziliantech one that does't exist anymore ?
EDIT: Thanks it's working now

Case Recommendation for K7N2 Delta-ILSR

Greetings,
I'm looking for a mid size ATX case that that has the front usb etc. ports prewired as to work easily with a K7N2 Delta-ILSR mb. By that I mean I don't have to plug each wire individually (with names that don't match) just a plug that goes on the mb. My eyesight isn't as sharp so hooking up those one wire at a time is tediuous. Not to mention the lack of starndards Does anyone know if this is address on the next rev of mb's (with pcix etc).
Thanks

Brazos,
I have yet to see a case that has all the USB wires together, they are all 1 pin at a time. You will find the Antec line of cases very good. (You can always use a magnifying glass to see the pins.) The pin names on the Antec cases are standardized and easy to figure out.
If you want a good case at a cheap price, then go with the SLK3700AMB:
If you want a good high end case, then go with the Sonata:
If weight is an issue, then go with the Super Lanboy:
Take Care,
Richard

Warranty Length for K7N2 Delta-ILSR

What is the mfg's warranty length on the K7N2 Delta-ILSR?
I filled out the online support form earlier today but no response as of yet, and me being the impatient rascal I am, I didn't want to wonder all weekend. I bought it October, 2003 and the floppy drive controller seems to have gone out.
Thanks!
HH

Thank you, Glenn!
Looks like mine is 2 yrs. & 4 months old. Kind of stinks that I lost 5 months on the warranty by going by the mfg. date instead of date of purchase. Its not worth the hassle & would even cost more to RMA it for the controller. Ahh, but this is IT, the "World of Workarounds". I'll live!
Thanks for your time, Glenn!
HH

Temperature reading for K7N2 Delta ILSR

I have a 2500+ Barton (333 FSB) to work with K7N2 Delta ILSR and 2x256 MB Samsung DDRAM(400 FSB).I use MBM to read my CPU temperatures.Usually 45-47 C idle and 54-58 C under full load.I overclock CPU to 400 FSB and I get LOWER TEMPERATURES!!!!!
I use 1:1 bios setting for CPU and DRAM speeds either 333 or 400 FSB.
How can this by possible?

I use Speedfan which seems to follow the temp in the bios. I've heard that MBM is also accurate. As far as your temps going down on a OC that is very odd indeed.

Anyone help - need I/O plate for K7N2 Delta ILSR??

I'm based in the UK but will pay P&P worldwide........
cheers
D.

Good luck!
http://search.stores.ebay.com/ws/search/StoreItemSearch?catref=C5&fcl=3&from=R7&frpp=50&fsoo=1&fsop=1&sacat=-1&satitle=k7n2+delta+ilsr&sbrexp=WD1S&sif=1&sofindtype=0&sofp=4&ssPageName=WD1S
Edit: If applicable:
http://www.mycableshop.com/sku/ATXBACKPLATE.htm

Replacement Chipset/Heatsink Fan (northbridge? for k7n2 delta-ilsr)

< i need a replacement heatsink and fan for this fan. that will fit! Reason: I want a new one that is quiter, and the original fan in it broke. I also need to be able to buy these part(s) online.

Me too. You can get them in copper or aluminium. I have the latter, and for more than year now it's been doing a fine job with minimum noise.
Check it out here:
http://www.pcabusers.com/reviews/iceberg/p1.html

Best agp card for k7n2 delta ilsr

Hi again folks
I'm thinking of upgrading my graphics card as although this card has never let me down its the oldest component in my box, I would like to get something in the sub £100 range, I dont do games but may wish to in future, mainly it would be for photo apps/running-backup-watching dvd's etc. any info would be greatly appreciated tia Hazzo

I notice your talking in £'s so I assume your located in the UK.
Have a look around overclockers.co.uk
For a sub £100 I noticed a good offer:
HIS ATI Radeon 9800 Pro - £82
Also, the 6600GT here is only £103.24 (£106 inc delivery), altough only 4 left in stock so buy now if you want one

Dont find any connection for PFC on K7N2 Delta ILSR

Hi !
Just bought a MSI Motherboard K7N2 Delta ILSR
Looking for the connector pin for my PFC ( Power fan Control)
I can only find two fanconnectors on the board
CPU and System
SORRY if this question has been asked before
searched the Forum but did not find anything

I just installed this same board. I only found 2 also, so I suppose that is all there is. If you are trying to set the system up so you can monitor the power supply temps and fan, here is what I did.
The chipset fan is a 12V fan, so unplug it from the motherboard and power it by using an adapter so you can run it off one of the Molex leads. I do not know if they make these because I fabricated the wiring myself. You will not be able to monitor the chipset temps though.
To fab the connector, I just used the wiring from an old system fan and soldered two small pins (about one-quarter of an inch long), covered each lead with heat shrink and plugged them in via a standard Molex connector. Make sure that you do not leave any of the pin exposed, ie: (the heat shrink should push up to the plastic of the chipset fan connector).. I finished it by covering the new connector with heat shrink to make sure it didnot come apart.
Now you can use the northbridge fan control for the pfc. This has worked good for me, and was $30 cheaper than a fan controller unit

Best Cooler For XP 3000+ on K7N2-Delta ILSR?

As the title suggests I am looking for a good, high performance Heatsink and Fan for my current XP 3000+ system. I have a K7N2 Delta ILSR mobo. Three Heatsinks I have been looking at are:
Thermaltake Volcano 12 Extreme
Thermalright SLK-900A with a Vantec Tornado 92mm fan
Thermaltake SilentTower - (I think this one requires holes in the Mobo which the K7N2 Delta ILSR doesn't have :( Please correct me if I am wrong).
I am looking for a high-performance heatsink at an affordable price (max £50) with which I can do some overclocking. Currently I have one of the Zalman ones ( I think it is a CNPS6000-CU) which is insufficient (load temps 66 C). Help would be much appreciated. Thanks in advance.

Yeah, i'm looking for a good price vs performance vs noise solution really. Both the Volcano and the Vantec Tornado are really loud, but they seem to perform quite well.

K7N2 Delta-ILSR + FX5700-256td = PC Shudown and Lock

i play a Doom 3 demo or Morrowind and in the short while to be playing the computer it is extinguished
MSI K7N2 Delta-ILSR (v7.8 Bios)
MSI FX5700-256td (last bios)
AMD Sempron 2600+
512 DDR
300W power
WinXP SP2, Suse Linux 9.1
all patch´s and last drivers for all OS
I look the 8X AGP dont work...
4X Agp works... Im proving now

AMD Athlon Sempron 2600+
MSI K7N2 Delta - MS-6570
MSI FX5700-TD256
System BIOS : 08/02/2004-nVidia-nForce-6A61BM4CC-00
Memory: 512MB 16x(32Mx8) DDR-SDRAM PC3200U-2533-600 (CL2.5 up to 200MHz)
HD: 80G SATA
Voltage Sensor(s)
CPU Voltage : 1.55V
Aux Voltage : 1.63V
+3.3V Voltage : 3.25V
+5V Voltage : 5.03V
+12V Voltage : 11.98V
-12V Voltage : -12.03V
-5V Voltage : -5.15V
Standby Voltage : 4.97V
AGP Bus(es) on Hub 1
Version : 3.00
Speed : 4x Fast-Writes Enabled : No
Isochronous Mode Enabled : No
Addressing Enabled : 32-bit
Aperture Size : 128MB

K7N2 Delta ILSR won't boot from FDD or HD

I have a serious problem with my new K7N2 delta ILSR based computer.
My machine is
K7N2 delta ILSR 400W
3.3/25 5/32 12/15 V/A PSU
512+256 MB A-data 3200 ram
Athlon XP2500+
BTC 48x24x48 Combo
100 mb Zip int. -disabled
120 GB Seagate barracuda SATA-disabled
120 GB Seagate Barracuda parallel
Triplex parasouls ATI 9600PRO 128MB
The machine POST's normally with all 4 lights doing what they should.
The Promise BIOS can detect the SATA drive correctly but when an attempt is made to write the array an error- 'error modifying array- system is going to reboot- press any key to reboot>" is given.
The M/B BIOS detects the FDD and Seagate Parallel drives correctly but when a correctly formatted XP boot disc (or Mandrake Linux or Caldera DR-DOS) is placed in the floppy drive a "no system disk" error is given.
When you F6 to install RAID drivers in the Windows XP install and the screen comes up where you are prompted to insert the floppy there is no mass storage device detected.
I purchased a new FDD and it gives precisely the same error as the original.
I installed the parallel Seagate in another system and installed and activated windows XP on it. After re-installing it in the K7N2 system I was disappointed to discover that it will not boot off the hard drive. When you boot from the XP CD the machine locks up. (Disconnecting the HD it will boot normally)
This is a real puzzle as it is possible to format the hard drive using Max Blast3- the maxtor disk utility which is based ( as is the Seagate Seatools utility) on Caldera DR-DOS). And I can't see why it should boot from a CD-ROM and not from any other correctly formatted boot disk.
I suspect a problem in either the (South?) bridge that controls the peripherals or the BIOS. I am at a loss how to re-flash the BIOS with out the use of the floppy drive- unless this can be done from a CD-ROM.
The PSU is not being strained and nForce list both RAM sticks as OK.

Quote
Originally posted by Wonkanoby
is the fd light on all the time,as that means the ide type lead needs flipping 180 degrees in the back of it
is the hard drive ide 80 wire ,blue end in the board
any thing shorting under the board,an extra stand off or the like
The Fd light behaves normally. i.e. lights up when the drive is being accessed.
has anybody else noted that the FDD is B by default- That the cables have a few wires twisted like the wires between the first and second plugs on the old cables?
The IDE 80 wire(counted!) is long end in the board- my plugs are all 3 black. You can't put them in the wrong way becaue of the centre key.
All the stands are plastic except for two brass ones that are in the centre of the board that go to circular mount pads. That is how the case came and I thought it was a design feature.
The thing I find most puzzleing is that i can boot a caldera based system that finds everything including the floppy- and read it- (provided you call it drive B!) yet naything DOS based won't go- I have this feeling that it has a screwed up DOS call that is not looking in the right disk sector for NTldr or whatever to boot. I think this is a bios problem- but I am not sure how to find out when you can't boot from the FDD.
My brother has talked to some tech friends and there word is that this is a weird one- probably a dud board RTS.

Linux for K7N2 Delta-ILSR

Similar Messages

Maybe you are looking for