Linux Hamachi doesnt work properly [SOLVED]

When I run the linux hamachi, I seem to be disconnected from hamachi all the time. everyone else says that I'm "blinking"... When I run hamachi inside of VirtualBox under XP, it runs fine...
1) Is there a way to make hamachi work without reconnecting every minute under linux?
2) If not, is there a way to run hamachi inside VirtualBox, but make the network available outside, in the host? I tried using "Host interface" to connect the Guest with the Host and creating a bridge between the hamachi interface and the LAN interface inside of XP but it didnt seem to work...
Thanks for any suggestions..
Last edited by icetonic (2010-05-15 11:53:06)

Hmm I checked the FAQs
running
iptables -A POSTROUTING -t nat -o ham0 -j MASQUERADE
as suggested didnt help...
EDIT:
Finally found the fix - its a compatibility problem with the new windows clients and the old linux version...
creating the file ~/.hamachi/config with content
KeepAlive 10
helped
Last edited by icetonic (2010-05-15 11:52:54)

Similar Messages

  • Replace content smart objects doesnt work properly.

    Hello fellow Photoshoppers,
    Currently i am working on reusable album templates with smart objects. At first i was very enthusiastic but this was soon to end. as the replacing doesnt work properly.
    I made the smart object by using:
    1. > file
    2. > place
    then i try to replace the content by using.
    1. > layer
    2. > smart objects
    3. > replace contents
    the old image should get replaced by the chosen file and matching size, smart layers etc. However when i perform the same actions my image gets replaced but it is not the same size as the smart object it replaced. This makes the entire template useless as it would take far too much time resizing every single image. inspired by another video I also tried double clicking the layer and tried replacing the image in the editing sceen by dragging another file on top of the smart object. Again, it does not spread out to the full smart object size and i'm stuck with a small image in need of extra work.
    Needless to say, very frustrating.
    Any thoughts?

    Are you sure you understood how it is intended work?
    That is an interesting question, i have no experience with photoshop as i bought CS5,5 just a week ago and have no experience with any of the previous versions either. All info regarding how to make such a template i found from various tutorials, i posted one below. When they do it the image get scaled perfectly. Now since they use some smart filters in the tutorial i applied them aswell to see if this would fix the problem but it did not.
    http://www.picturesocial.com/video/wedding-photo-album-templates
    Are the images you want to switch in at least always of the same width to height-relation?
    I checked both files for consistency and discovered they were shot on different camera's. One file ( the origional smart object ) was cropped form a 21,0MP file and the other was croped from a 10,1 MP file. Both images were cropped to a 2x1 ratio. Having discovered the difference in pixel amount i cropped a different 21,0 MP file to 2x1 ratio and checked both files for their exact dimensions (both images are equal in size with 5616 x 2808 pixels) and replaced the content with the newly cropped file which gave a much better result. However, the image was slightly smaller in photoshop leaving a small gap where the origionally placed smart object lined up perfectly. I turned the situation around and placed the 10,1MP cropped image as the smart object and replaced the content by a 21,0 MP cropped image. As to be expected i ended up with a new image much larger then the smart object. So the smart object does not constrain the files to the dimensions set. As it turns out it only scales the replaced content relative to the size of the origional content of the smart object.
    I just need a reusable template with objects that:
    - cannot be moved once locked ( if possible) but can have its content replaced
    - scales the replaced content to the predefined dimensions
    - needs no prework like cropping to the same aspect ratio as the smart object content. ( i want to be able to place a landscape sized raw (3x2) on any landscape format  (2x1 / 16x9 / 4x3 or whatever) i find it acceptable to having to crop a portret to landscape orientation first before being able to replace a landscape.
    now ive been searching for more info and some people say indesign is much faster in making album pages so I am installing the program as we speak hoping this will be the solution.

  • Keypad doesnt work properly

    my iphone keypad doesnt work properly the last row where the space bar and the button to switch to numbers doesnt work

    Standard troubleshooting steps in order are power the iPhone off and on, Reset, Restore and if not change after any and all, make an appointment at an Apple Store if there is one nearby or call AppleCare - (800) 694-7466.

  • Ejecting external discs doesnt work properly, no spin down of disc. why?

    ejecting my external discs doesnt work properly anymore in 10.6, no spin down of disc happens, the finder unmounts the disc(s) and then the disc spins on and on. thats weird, because, in 10.5 i ejected discs and then they went spinning down the drive, as it has to be.
    when i unplug the disc, which is unmounted from desktop, and still spinning, it makes a terrible noise in the disc. like a high pitched short tone.
    any idea whats going wrong here?
    thanks!

    you probably mean "causing the fail to spindown"
    you maybe mean software like techtoolpro5 or drive genius3?
    yes i disabled these helper apps on the discs, but first i used it (like monitoring
    all discs if they are nearly full, or working s.m.a.r.t and so on. yes its useful,
    but obviously it causes problems. i must mention, that i tested my 4 external drives again,
    and i found out that i can eject all discs, like said before, but only 2 of the discs are spinning down, after ejecting, BUT only when i use the button "eject" in harddisctoolkit, they dont spin down, when ejecting from desktop (apple+E), and the other 2 of the 4 drives refuse to spin down, after ejecting, even with pressing eject in harddisctoolkit....
    i can also state, that these 2 discs, which refuse to spin down, are FW800/400 discs and connected via FW800. and the 2 discs which spin down succesfully are UBS2 discs, if thats worth mentioning...
    Message was edited by: purepeter

  • My GX630 doesnt work properly on Windows Vista 64 bit

    Hi,
      I have problem with my GX630, its doest work properly at W Vista 64 bit, exactly Sleep mode ... its imposible to awake my computer nd I have to turn it off and than on to wake it up ...
      those buttons Turbo nd Eco mode doesnt work.
      sometimes happen that i get blue error screen and reset but I dont know why ... it wrotes something with some .dll file ...
    some people told me that its error is caused by that thing that there are no drivers for 64 vista yet ...
    I would be pleased if someone could help me up to this topic or to my email (removed to protect user privacy) or ICQ (115-378-414)  thank to all of you Jabu

    "sometimes happen that i get blue error screen and reset but I dont know why ... it wrotes something with some .dll file ... "
    What is the BSOD error code? What .dll ? Write down the exact error.
    Do you OC your notebook?
    "some people told me that its error is caused by that thing that there are no drivers for 64 vista yet ... "
    Install Drivers from MSI web:
    http://global.msi.eu/index.php?func=downloaddetail&type=driver&maincat_no=135&prod_no=1513
    "those buttons Turbo nd Eco mode doesnt work."
    You need SCM: http://global.msi.eu/index.php?func=downloaddetail&type=utility&maincat_no=135&prod_no=1513
    But x64 bit is N/A.
    Why you use x64bit version anyway? Why not 32bit?

  • JavaMail doesnt work properly with locally installed qmail

    'lo ppl
    i have a mail application using JavaMail on a linux box. everything works alright when i use any external host with a different mail server from qmail. but when i configure the program to use localhost (where qmail runs) it successfully sends the mail but it never gets delivered. the mail log says
    Sorry,_I_couldn't_find_any_host_named_xxxx.com?._
    it appends a ? to the hostname but i dont know why. this ? doesnt appear anywhere in the source. for any other programs qmail works absolutetly correct.
    did anyone of you experience the same problem and can help?
    thanks a lot.

    Hi,
    I don't think that it would be the problem of JavaMail.
    I have ever installed James on my win2000 professional
    . And My JavaMail application send mail via James in
    the localhost to the Internet . Such as yahoo, or other.
    But my James could not receive email for me. Because
    it is not set MX record.
    good luck,
    Alfred Wu

  • Geforce 295GTX doesnt work properly.

    I've bought a new 295GTX MSI. I uninstalled my previuos video card drivers, plugged in the new card. Everything boots up wel but once in windows Vista it detects the new hardware but could not recognize it. I installed the Nvidia drivers, they install fine but it's like it doesnt detect the card either. When i go and look to the properties its still using the default vista vga drivers. When I look at the properties there are only questionmarks at the brand name, chipset,... .
    I reinstalled Vista but i still get the same bug. Tried it in Windows 7, still the same bug.
    Tried it in another computer, still the doesnt work.
    P.S.: All power cables are properly connected.
    What can I do?

    Hi Hansie! Give this a try; In 'Change or Remove Programs' (not sure if it is called that in Vista), Uninstall NVIDIA PhysX (if installed), NVIDIA Performance (if installed), NVIDIA Drivers - NVIDIA Display Driver only. Install NVIDIA Ver. 181.22 (use Aaron's link), & reboot, install NVIDIA Utility Package Ver. 6.03. In the NVIDIA Control Panel - 3D Settings - Set Multi GPU & PhysX - 'Enable' PhysX & Multi GPU Mode. Hopefully that fixes everything.

  • Graphire 4 no longer working properly(SOLVED)

    Hi. I had my tablet (Wacom Graphire 4) working perfectly shortly after I joined these forums. However, a recent update or something has made it so that my tablet doesn't work properly, despite no discernable changes in my xorg.conf. Here's the relevant information that I could gather. I'll be glad to gather additional info as it's needed.
    xelados@sporkbox: ~ $ cat /proc/bus/input/devices
    I: Bus=0003 Vendor=056a Product=0015 Version=0403
    N: Name="Wacom Graphire4 4x5"
    P: Phys=
    S: Sysfs=/devices/pci0000:00/0000:00:02.0/usb1/1-5/1-5:1.0/input/input3
    U: Uniq=
    H: Handlers=mouse2 ts2 event3
    B: EV=1f
    B: KEY=1c63 70011 0 0 0 0
    B: REL=100
    B: ABS=10003000003
    B: MSC=1
    Here's my /etc/X11/xorg.conf:
    Section "InputDevice"
    Driver "wacom"
    Identifier "mouse"
    Option "Device" "/dev/input/wacom"
    Option "InputFashion" "Tablet"
    Option "Mode" "Absolute"
    Option "Name" "Graphire 4 (USB)"
    Option "SendCoreEvents" "on"
    Option "Tilt" "on"
    Option "Type" "cursor"
    Option "USB" "on"
    Option "ZAxisMapping" "4 5"
    Option "Speed" "1.0"
    Option "WACOM"
    EndSection
    Section "InputDevice"
    Driver "wacom"
    Identifier "cursor"
    Option "AlwaysCore" "on"
    Option "Device" "/dev/input/wacom"
    Option "InputFashion" "Tablet"
    Option "Mode" "Absolute"
    Option "SendCoreEvents" "on"
    Option "Tilt" "on"
    Option "Type" "cursor"
    Option "USB" "on"
    EndSection
    Section "InputDevice"
    Driver "wacom"
    Identifier "stylus"
    Option "Device" "/dev/input/wacom"
    Option "InputFashion" "Pen"
    Option "Mode" "Absolute"
    Option "Protocol" "Auto"
    Option "SendCoreEvents" "on"
    Option "Tilt" "on"
    Option "Type" "stylus"
    Option "USB" "on"
    EndSection
    Section "InputDevice"
    Driver "wacom"
    Identifier "eraser"
    Option "Device" "/dev/input/wacom"
    Option "InputFashion" "Eraser"
    Option "Mode" "Absolute"
    Option "Protocol" "Auto"
    Option "SendCoreEvents" "on"
    Option "Tilt" "on"
    Option "Type" "eraser"
    Option "USB" "on"
    EndSection
    ...And the udev rule to accompany it (10-wacom.rules):
    KERNEL=="event*", SYSFS{idVendor}=="056a", NAME="input/%k", SYMLINK="input/wacom"
    I would appreciate any insight or support. I don't know what to do.
    EDIT: I checked Xorg's log and did a 'cat /var/log/Xorg.log.0 | grep "(EE)"' to see if anything came up. Here's the output I got:
    (EE) module ABI major version (0) doesn't match the server's version (2)
    (EE) Failed to load module "wacom" (module requirement mismatch, 0)
    (EE) module ABI major version (0) doesn't match the server's version (2)
    (EE) Failed to load module "wacom" (module requirement mismatch, 0)
    (EE) No Input driver matching `wacom'
    (EE) No Input driver matching `wacom'
    (EE) No Input driver matching `wacom'
    (EE) No Input driver matching `wacom'
    Here's a paste of the entire logfile: http://pastebin.archlinux.org/19973
    [SOLUTION] kappa's suggestion (to recompile the linuxwacom package) turned out to be the fix. My tablet works great now!
    Last edited by xelados (2007-11-27 11:44:45)

    The recent xorg 7.3 update requires to update the driver.
    Xorg-server 1.4, however, is not yet properly supported by linuxwacom.
    While the latest dev version mostly works, there are a number of problems:
    - xsetwacom/wacomcpl don't  recognize the tablet
    - several people have reported problems with brushes in gimp being offset from the stylus position
    - there is a bug where  left or up movement events are ignored by X
    In those cases, downgrading X is the only solution.
    Last edited by kappa (2007-11-24 18:58:31)

  • My iphone 5 sleep button doesnt work properly. Need help where can i get it fixed

    I bought my i5 in january from croma, delhi and last 5-6 days i am noticing that my sleep button is not working properly on the right side. I searched for solution on the net but all i got to know that this is a problem in iphone 5 and need to be replaced. And i have no idea how to get it fixed or where to contact to get it replaced. Need urgent help.
    Thanx in advance

    modular747 wrote:
    It means that for one year from the data of purchase, Apple will replace the phone with a refubished unit for any malfunction not due to abuse or physical damage (i.e dropping, exposure to water, etc,)
    To be clear, it's a new or refurbished unit, whichever Apple has in the replacement phone stream.

  • .swf doesnt work properly

    the movie includes about 40 scenes, and works properly, but
    when i add another scene and place a 5min long movie clip on it,
    most of the other scenes dont play, they stop at the first frame.
    and no matter what i do with publish settings its always the same
    story..what could i be doing wrong. could it be my computer..not
    enough memory or something? i havent tried to export it on any
    other computer.. help, please

    When you say "40 scenes", just a quick question, have you
    imported them directly on to the stage to play in the timeline or
    imported your scenes dynamically using action script? If you have
    imported your movie clips directly onto the stage, you might find
    your pc may crash, especially, if you do not have a lot of memory.
    believe it or not, a 5 minute movie clip can seem like a quite a
    large in Flash. What also happens, your swf file needs to import
    all your files before displaying them either onto your PC or on the
    Web. If you do not have enough memory, it will take a long time to
    play or ulimately crash. Try importing your movie clips
    dynamically, using the NetConnection and NetStream in actionscript,
    then all your swf file has only to import maybe your movie player
    or the first movie, then whilst your user is viewing the rest of
    your site, the other movies will not need to be viewed until your
    user clicks on the available movie clip or link.

  • App_debitcard.2.0.0.tcl - long pound doesnt work properly

    Hi friends!
    I trying long pound in standart application example.
    My incoming call from pots, then i enter pin code and destination number.
    I type pound key at ACTIVE status fsm machine and starts disconnecting process. When outgoing leg is disconnected, command media play streaming _reenter_dest.au in incoming leg (see it in debug), but i listen silence instead prompt voice.
    I can continue entering destination number again, make call and talks, but since long pound detected, i have no voice prompt listning.
    i tried some ioses, c5400-js-mz.124-9.T7 till c5400-js-mz.124-22.T, some other 124 line ioses, no one where long pound works.
    In 123 ios line same application works properly.
    Thanks all!
    DM

    DM,
    The script I'm using, it won't let the call pass through, unless my rate table has the exact number I'm dialing. The rate table has a column called pattern, this where all my int code including the area code are there, and yet I get to put the whole as is to make the call, eg 00114427846789, etc..
    If you can help please, the thing I need to know, do we control that from the script, or is it the billing itself?
    Regards,
    Jassem
    My dial-peers are perfectly ok.
    dial-peer voice 8000 pots
    description ***** INBOUND FOR 02... NUMBER *****
    application byb-cc1
    incoming called-number 92446889
    dial-peer voice 9991 pots
    description *** OUTBOUND 0011 INTERNATIONAL CALLS TO AAPT ***
    huntstop
    preference 1
    destination-pattern 0011T
    progress_ind setup enable 3
    progress_ind alert enable 8
    no digit-strip
    port 0:D

  • I "upgraded" to FF4, now it doesnt work properly, wont open pages, will open blank tabs when i click on a link, tried to go back to the older one but that doesnt work now either, have tested it with Safari and it opens everything fine. Any ideas?

    After upgrading to firefox 4 im now having a lot of problems using the browser.
    if i try an open a link in a new tab it will just open up a blank tab, if i click on links or even type in the google search bar at the top it doesnt do anything, it just says "done" and the circle thing stops as if im on the page already, have tested it with Safari doing the same things and Safari works fine. I'd swap but all my bookmarks and passwords are in Firefox so id rather stay with that.
    I tried going back to the older version of firefox (3.5 or something) but seems the bugs are here to stay now.......so.......any ideas? because its really annoying, shouldn't have "upgraded".
    Is there a new patch coming out anytime soon or should i start getting used to Safari?
    Thanks for your help.
    Mark Lavery (Melbourne)

    I would copy over the entire thing if you have room.  With iTunes 10.4 though, you can download any previous iTunes purchases you have made in the past with your current iTunes account.  While in iTunes, look at the left hand side of your screen and select "Purchases" and look at the bottom right corner of the screen and select "Download Previous Purchases".  If you have an iPhone, iPod and/or iPad...you can do the same thing from each device.  Nice new feature...just remember that those ripped CDs need a back-up!!!  Enjoy...

  • Hp Pavilion dv4 Fan doesnt work properly

    I cleaned the fan in my laptop, it was making big noise. I cleaned and put it again, there is no noise now but I think it works slow speed so my laptop is heatining  in a few minutes. What should I do? let me replace to a new fan? also i dont know exactly heat sink, what is that? how can i understand what is the wrong at the fan? it looks like properly works when I take it out

    do you have a comment about trade mark of a fan so i wanna get the non-quality one.
    When i look it the fan, It looks like works normally, Is there any way to understand its wrong? 
    somebody says replace heatsink, i dont know about it, What is heatsink? should i replace it? 

  • Tecra P5 - Volume control doesnt work properly

    Hi
    Since upgrade to Windows 7 64 bit I can't turn the volume all the way down by using the volume control at the front of the notebook. Worked fine under Vista 32 bit.
    The volume control still works but no matter how far I wind it to the left there is still sound coming from the speakers.
    Any help appreciated.
    Thanks
    Warren

    As far as I know volume control in the past was mechanical but now it works on different way and it is controlled by specific tool/utility.
    To be honest Tecra P5 is not known to me but obviously it is Australian notebook model and according to Australian support page this notebook model is not supported for Windows 7.
    That doesnt mean you cannot use it but this means there is not software package designed for Windows 7 that can be installed so I think there is no much you can do about it.
    I know it is annoying but for volume control you can use Windows option placed in task bar.

  • IChat doesnt work properly after mac update!

    I have only started using iChat recently and yesterday evening it was working fine! However, after being asked to install the most recent update on my mac, iChat has been acting a bit weird.
    The first time i opened it this morning, the program kept crashing and so i restarted my mac. iChat was opened again and worked well apart from no sound was being received by my machine when in an audio or video conversation. Sound WAS being transmitted to the usual standard to another mac. The other person made sure their microphone was not muted and was enabled. I made sure that the only available audio output on my mac was the built in output, and that the volume was fully turned up. I ran iTunes and played a song to test whether the sound was being routed to the main speakers, and it was! My friend then restarted their own mac to see if the problem lied with their machine.
    By a process of elimination i think that the recent update has affected iChat. Is there anyone else having this problem and if so is there a solution?

    I literally solved this issue an hour ago. The problem is in the latest update that you mention: it screws sound support in iChat.
    http://discussions.apple.com/thread.jspa?threadID=1068735&tstart=0
    If you don't want to go back to 10.4.9, then try this..
    http://barryp.org/blog/
    (scroll down to 'Logitech Camera')
    D.C.

Maybe you are looking for