LINV field for date when LINV-ISTAT changes to "L"

Hello,
I need to find out a date field from LINV table when the status in LINV-ISTAT changes to "L" ( Cleared ). Can anyone suggest which is the required LINV field for this?
Thanks

Hello Minal,
When you create Inventory document with LICC transaction (Quant inventory) at that time it will update the table LINV with inventory details, once you complete count and post difference at Warehouse level with LI20 transaction at that time it will update the table with status L (Cleared).
Hope this helps.
Regards
Arif Mansuri

Similar Messages

I have problem that changes i make wont be saved it all goes back to the same date that i had this problem for EX: when i ever change my desktop photo and reopen the macbook it goes back to the same photo that i had before.

i have problem that changes i make wont be saved it all goes back to the same date that i had this problem for EX: when i ever change my desktop photo and reopen the macbook it goes back to the same photo that i had before.

Might be corrupted preferences ..
Open the Finder. From the Finder menu bar click Go > Go to Folder
Type or copy paste the following:
~/Library/Preferences/com.apple.desktop.plist
Click Go then move the com.apple.desktop.plist file to the Trash.
Restart your Mac and try changing the desktop photo.

Why am I being charged for data when connected to wifi AND not using my phone?!

WHY am I being charged for data that I'm not using? At times when I'm asleep AND my phone is connected to wifi?! This happens at really specific, alternating times like 9:54 pm every day, or 12:01 am, 6:01 am and then 12:01pm and 6:01pm. When I called I was told "maybe your wifi at home is disconnecting" or "maybe your phone is connecting to atnt or sprint". It's not possible that my phone is disconnecting from wifi every six hours on the dot and, at that exact time, I'm always using data. I find it hard to believe that I live in a HUGE city and my phone magically connects to other networks and I NEVER notice this. Verizon is full of LIARS (and maybe’s) and I'm not convinced that these data charges are a coincidence. I was told to turn off my cellular data to see if the problem resolves itself. Why should I alter my daily life when Verizon is clearly the one with the issue? I hope there's a class action lawsuit because Verizon is trying to get over on everyone! I need answers!

Hello NotHappy101,
I think it's quite odd that your data usage is at very specific times. We can certainly take a closer look. Please reply to my Direct Message, so we can get some additional details.
Thanks,
MichelleH_VZW
Follow us on Twitter @VZWSupport

Delta field for Data Source 0BP_RELATIONS_ATTR

Hi Experts,
I need to know how to find which field is Delta enabled for standard Data Sources.
In my requrement for Data Source 0BP_RELATIONS_ATTR.
As the Data Source is being accessed by BODS sysetm and they need to know the Delta field to extract delta.
Thanks
Basheer

Hello,
Are you using Crystal Reports? If not I believe you should be posting your question to one of the Classic SAP forums:
http://forums.sdn.sap.com/index.jspa#45
Please mark as answered also.
Thank you
Don

Redetermine Org Data when Employee responsible Changed

Hi,
In my project we need to redetermine the org data when the employee responsible is changed.
With Regards,
Selvam T

hi,
one idea to solve this might be to use the event framework to capture the partner change and then call the CRM_ORGMAN_MAINTAIN_OW FM to change the organizational data. A call of CRM_ORGMAN_DETERM_INITIAL_EC might also do the trick, but I've never done that myself so far.
Hope that points you in the right direction.
Regards,
Hendrik

Too many fields QE-3018 when trying to change manager password

Hello, we are seting up a new database, we have uploaded tables with data transfer and copy express, and when trying to change the manager password we are getting this message.
thank you.
Jose.

Hi,
Check the below note 1304754:
[https://websmp230.sap-ag.de/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/sapnotes/index2.htm?numm=1304754|https://websmp230.sap-ag.de/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/sapnotes/index2.htm?numm=1304754]
Warmest Regards,
Chinho

Which BW Variable to be used for date when creating service in portal

Hi,
Can any one please let me know which BW variable is to be used for date(range) when creating a portal service for searching based on dates.
Thanks
Abhai
Message was edited by:
Abhai

Hi Arun,
its just a portal service which would be called when searching a document created on a particular date or betwwen a range of date.so what i require is which BW variable to be used when handling range.As for variable technical name we use VAR_NAME_I and for single value variable we VAR_VALUE_EXT_I
in the similar manner i want BW variable to be used for range of values.
Thanks
Abhai

Please expose the employee ID field in ADUC in this version, also add a field for data of birth, and present both on the change password form so we can validate a user's identify when they ring up for a reset.

Considering Active Directory is supposed to be all about business, corporations and enterprises, I find it staggering that in 2015 the ADUC console STILL does not expose the Employee ID field in the default UI without having to dig into the attribute editor.
And then only if you browse to the user in their OU, the Attribute Editor tab is missing when you just search for the user. This isn't really helping our organisation. I've just setup the tech preview version of the new server version, and that doesn't expose
it either.
I'm not sure how other organisations handle this (suggestions please?), but when a user rings up the service desk for a password reset, we either have to keep them on the phone while we dig into their user account and look for the Employee ID for them to
then confirm on the phone, or just take it on blind faith that they are who they say there are.
Please for the love of all deities, can you expose the Employee ID field on the main user panel without having to dig into attribute editor. It would also be useful to show this information directly on the reset password dialog box so there's no looking
up required. While you're at it, please can you add a date of birth field (if it isn't already there, I never seen one), and expose this on the main screen for the user, as well as the reset password box. This would give us two pieces of information to verify
the identity of the user on the phone.
All that being said, if anybody has a better way of identifying users on the other end of the phone, I'm all ears.
Thanks in anticipation.

Personally we use the AD selfservice plugin for manageengines service desk plus.

Hide fields for activities when they are opened via Activity Monitor

Hi,
In CRM 5.0, my requirement was to hide a number of fields from activity display via transaction CRMD_ORDER & CIC0 (SAPGUI based transactions). I achieved it by using screen variant. I assigned my screen variant to different transactions (CRMD_ORDER, CIC0 etc.), and things were working fine.
But when I open activity monitoring report (transaction S_AE2_89000019), search for some activities and open an activity by double-clicking in the report, the hidden fields become visible. Although, the transaction being displayed in CRMD_ORDER.
I couldn't enable my transaction variant for transaction S_AE2_89000019, obviously because this is a report transaction which in turn opens activity when we double-click on the grid.
Any idea how to avoid these hidden fields being displayed via S_AE2_89000019?
Regards,
Kaushal

Hey Kaushal,
Let me first inform you the following:
1) Transaction Variant are associatated to Dialog transactions only......Which means when u call report which eventually refers the same transaction even then the transaction variants is not called....
For the whole transaction variant to workout, you need CALL transaction " ..."....
2) The transaction S_AE2_89000019 is not a dialog transaction, its a parameter transaction which eventually calls a report AQZZ/SAPQUERY/SMCRM_REP_ACT1==
3)This report in turn uses the call to FM CRM_1O_CALL_FOREIGN which launches that crmd_order transaction screen and not crmd_order transaction..
You can enchance that report by creating a z report and inside that z report you can fulfill your requirement..
Inspire ppl by reqwarding..
Regards,
Anand...

Asking for passcode when trying to change restrictions on iphone 3gs

In response to a person on here for deleting a gmail account from an iphone 3GS
I can not enter the passcode for restrictions?
Can anyone assist?

If You Are Locked Out Or Have Forgotten Your Passcode or Just Need to Restore Your Device
1. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
3. iOS- Understanding passcodes
     If you have forgotten your Restrictions code, then follow the instructions
     below but DO NOT restore any previous backup. If you do then you will
     simply be restoring the old Restrictions code you have forgotten. This
     same warning applies if you need to restore a clean system.
A Complete Guide to Restore or Recover Your iDevice (if You Forget Your Passcode)
If you need to restore your device or ff you cannot remember the passcode, then you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and re-sync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone, iPad and iPod touch software.
Try restoring the iOS device if backing up and erasing all content and settings doesn't resolve the issue. Using iTunes to restore iOS devices is part of standard isolation troubleshooting. Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition.
Before restoring your iOS device, Apple recommends that you either sync with iTunes to transfer any purchases you have made, or back up new data (data acquired after your last sync). If you have movie rentals on the device, see iTunes Store movie rental usage rights in the United States before restoring.
Follow these steps to restore your device:
     1. Verify that you are using the latest version of iTunes before attempting to update.
     2. Connect your device to your computer.
     3. Select your iPhone, iPad, or iPod touch when it appears in iTunes under Devices.
     4. Select the Summary tab.
     5. Select the Restore option.
     6. When prompted to back up your settings before restoring, select the Back Up
         option (see in the image below). If you have just backed up the device, it is not
         necessary to create another.
     7. Select the Restore option when iTunes prompts you (as long as you've backed up,
         you should not have to worry about restoring your iOS device).
     8. When the restore process has completed, the device restarts and displays the Apple
         logo while starting up:
           After a restore, the iOS device displays the "Connect to iTunes" screen. For updating
          to iOS 5 or later, follow the steps in the iOS Setup Assistant. For earlier versions of
          iOS, keep your device connected until the "Connect to iTunes" screen goes away or
          you see "iPhone is activated."
     9. The final step is to restore your device from a previous backup. If you do not have a
          backup to restore, then restore as New.
If you are restoring to fix a forgotten Restrictions Code or as a New device, then skip Step 9 and restore as New.

Using number field for date

Hi,
I have a number field that contain a date (YYYYMMDD). In my report I must show the date in the format DDMMYYY.
Please, help me.
TIA, Alex
null

Hi,
You can also change your query...
Instead of the column you are using, use
to_char(
to_date(
ltrim(
to_char(<date_field>)
, 'YYYYMMDD'
, 'DDMMYYYY'
Hope this helps

Default start year 1920 for date pciker: how to change ?

Hi,
in a date field i use a datepicker with app date format.
calling to select a date, the popup shows default the month and year 1920.
how to change it in the current year ?
any reaction will be appreciated.
Leo

Hello Leo,
It has to start somewhere...but it is depending on the value of the item. If you set a default to the item, it shows up on that date. But I guess you probably don't want to set a default...
Greetings,
Roel
http://roelhartman.blogspot.com/
http://www.bloggingaboutoracle.org/
http://www.logica.com/
You can award this reply to your question by marking it as either Helpful or Correct ;-)

OLM-Updating requirements for LP when person type changed to ex employee

Hi,
When the person type changes to Ex employee and enrollments still exists (which have not yet been completed) the following error message shows up.
USER DEFINED EXCEPTION IN PACKAGE OTA_DELEGATE_BOOKING_SWI PROCEDURE UPDATE_DELEGATE_BOOKING
when trying to update the enrollment status to Attend for those people who were part of a Learning Path subscription list. On other cases (employee is not a subscriber to a LP) the enrollment can be completed (Attend).
Has anyone experience this issue?
Best regards,
Roberto

Navigate to Work Structures -> Status and query for all rows with system status Terminated Assignment. select your required assignment status as Default. Untick the other default.

Configuration workaround for fancontrol when hwmon order changes

I run Arch Linux on Asus P8Z77-V Pro Thunderbolt motherboard. I used nct677x-git module with lm_sensors and created configuration for fancontrol and everything worked until some of the next reboots. hwmon[0-3] order on my machine is not persistant, sometimes it was...
hwmon0 is acpitz
hwmon1 is asus
hwmon2/device is coretemp
hwmon3/device is nct6779
other times...
hwmon0/device is nct6779
hwmon1 is acpitz
hwmon2/device is coretemp
hwmon3 is asus
or...
hwmon0/device is nct6779
hwmon1 is acpitz
hwmon2 is asus
hwmon3/device is coretemp
Since I'm no expert it took me while to figure out that the best way is to reference devices directly instead of hwmon. Another thing is that in 2009 there was a patch that introduced DEVPATH and DEVNAME (they are expected to be hwmon's). It checks for symlinks and will exit if fails so the easiest workaround is to enter empty values in DEVPATH.
This is my working hwmon order independent setup.
# Configuration file generated by pwmconfig, changes will be lost
INTERVAL=10
DEVPATH=/sys/devices/platform/nct6775.656= /sys/devices/platform/coretemp.0=
DEVNAME=/sys/devices/platform/nct6775.656=nct6779 /sys/devices/platform/coretemp.0=coretemp
FCTEMPS=/sys/devices/platform/nct6775.656/pwm1=/sys/devices/platform/nct6775.656/temp1_input /sys/devices/platform/nct6775.656/pwm2=/sys/devices/platform/coretemp.0/temp1_input /sys/devices/platform/nct6775.656/pwm3=/sys/devices/platform/nct6775.656/temp1_input /sys/devices/platform/nct6775.656/pwm4=/sys/devices/platform/nct6775.656/temp1_input
FCFANS=/sys/devices/platform/nct6775.656/pwm1=/sys/devices/platform/nct6775.656/fan1_input /sys/devices/platform/nct6775.656/pwm2=/sys/devices/platform/nct6775.656/fan2_input /sys/devices/platform/nct6775.656/pwm3=/sys/devices/platform/nct6775.656/fan3_input /sys/devices/platform/nct6775.656/pwm4=/sys/devices/platform/nct6775.656/fan4_input
MINTEMP=/sys/devices/platform/nct6775.656/pwm1=20 /sys/devices/platform/nct6775.656/pwm2=20 /sys/devices/platform/nct6775.656/pwm3=20 /sys/devices/platform/nct6775.656/pwm4=20
MAXTEMP=/sys/devices/platform/nct6775.656/pwm1=60 /sys/devices/platform/nct6775.656/pwm2=60 /sys/devices/platform/nct6775.656/pwm3=60 /sys/devices/platform/nct6775.656/pwm4=60
MINSTART=/sys/devices/platform/nct6775.656/pwm1=152 /sys/devices/platform/nct6775.656/pwm2=64 /sys/devices/platform/nct6775.656/pwm3=152 /sys/devices/platform/nct6775.656/pwm4=90
MINSTOP=/sys/devices/platform/nct6775.656/pwm1=32 /sys/devices/platform/nct6775.656/pwm2=34 /sys/devices/platform/nct6775.656/pwm3=32 /sys/devices/platform/nct6775.656/pwm4=60
I spent a lot of time searching but I just didn't find anything like that so my intention is to link to this sample config from wiki.

Yes the characterstics were maintained for the main item.
and the delivered item was a subitem for this main item.
So characterstic were maintained for Item 10(Main item) but delivery was done for some of its sub item was item 100 / 120
Also can i know where is this setting or configuration where we configure this to block the configuration if any of the subitem is delivered.
Thanks
Kaushik.

Getting no data when it got changed from Oracle Database 10g to 11G

Hi All,
Below decode column is not working in Oracle database 11G but it is working in 10g. Please advise.
{DECODE('Y',DECODE(cr.segment4,DECODE(cr.segment5,'007','32020','N'),'Y','N')
,DECODE(SIGN(DECODE(pacd.line_num_reversed,NULL,pae.raw_cost,( -1*pae.raw_cost ))),-1,DECODE(INSTR(pae.expenditure_type,'Accrual'),0
,pae.project_exchange_rate*DECODE(pacd.line_num_reversed,NULL,pae.raw_cost,( -1*pae.raw_cost )),pae.project_exchange_rate*DECODE(pacd.line_num_reversed,NULL,pae.raw_cost,( -1*pae.raw_cost ))*-1),( -1*pae.project_exchange_rate*DECODE(pacd.line_num_reversed,NULL,pae.raw_cost,( -1*pae.raw_cost )) ))
,DECODE(dr.segment4,DECODE(dr.segment5,'007','32020','N'),'Y','N'),DECODE(SIGN(DECODE(pacd.line_num_reversed,NULL,pae.raw_cost,( -1*pae.raw_cost ))),1
,pae.project_exchange_rate*DECODE(pacd.line_num_reversed,NULL,pae.raw_cost,( -1*pae.raw_cost )),( pae.project_exchange_rate*DECODE(pacd.line_num_reversed,NULL,pae.raw_cost,( -1*pae.raw_cost)) ))) "Amount"
Regards,

WRONG FORUM!
This forum is for sql developer questions only.
Since this is not a SQL Developer question it should be posted in the SQL and PL/SQL forum
PL/SQL
Please mark this question ANSWERED and repost it in the other forum.

LINV field for date when LINV-ISTAT changes to "L"

Similar Messages

Maybe you are looking for