List of current incoming calls
How do I get a list of current (not yet billed) incoming calls? Someone called, left an important message, didn't leave a number.
Doesn't work for all types of accounts. For those it does, Its as of the bill date.
I remember when all phone bills listed such but I haven't seen for my accounts in years.
note FIOS Digital Voice customers can see on the www.verizon.com/fiosvoice
Similar Messages
-
000049: Oct 26 14:51:04.181: %VOICE_IEC-3-GW: H323: Internal Error (H323 Interwo
rking Error): IEC=1.1.127.5.21.0 on callID 261 GUID=80316352D0FE011E02002302A5CC
B8F9
000050: Oct 26 15:24:50.315: %CALL_CONTROL-6-CALL_LOOP: The incoming call has a
global identfier already present in the list of currently handled calls. It is b
eing refused.
000051: Oct 26 15:24:50.315: %VOICE_IEC-3-GW: CCAPI: Internal Error (Incoming lo
op): IEC=1.1.180.1.28.0 on callID 0
000052: Oct 26 15:24:50.315: %VOICE_IEC-3-GW: H323: Internal Error (H323 Interwo
rking Error): IEC=1.1.127.5.21.0 on callID 363
According to Cisco it says:
It means that the voice gateway has detected a loop in the call route
What debugs can I do to track this problem down.
All dial peers are like this. They are all voip dial peers with different destination-patterns and different session target IP addresses. No PSTN dial peers at all.
dial-peer voice 30000 voip
huntstop
destination-pattern 3[01]...
session target ipv4:192.168.99.4
dtmf-relay h245-signal
ip qos dscp cs5 mediaQ: How long has this system been in place - is it a new system, or is this something that just started on a system that has been in place for awhile?
A: My customer says to me that this system has been in place for nearly a year and the problem started only a couple of days ago.
Q: If so were there any changes to the infrastructure, or the dialplan in particular?
A: Again this is the first question I asked and he said “NO CHANGES”. But that is what most customer say – right?
Q: Have you seen this occur in the past in the logs? If so how often do you see it?
A: Started on 26th Oct 2010. Since the problem started the router has been reloaded and the problem is still there. It is very intermittent and I have to do the debug when I get the problem.
Q: Have you tried to establish what is causing these: H323: Internal Error (H323 Interworking Error) ?
A: Not sure how to troubleshoot this. The explanation of this message on CCO is not that great. -
Where do I see a list of my incoming calls online
Where can I see a list of my incoming calls on the Verizon website?
Doesn't work for all types of accounts. For those it does, Its as of the bill date.
I remember when all phone bills listed such but I haven't seen for my accounts in years.
note FIOS Digital Voice customers can see on the www.verizon.com/fiosvoice -
Hi
Really simply query here.
Is it possible for BT to provide a list of all incoming calls to my BT number over a period of several weeks? This would be retrospectively (i.e. I don't want to set something up now, I want the information for weeks that have already passed).
That is INCOMING and not OUTGOING ones.
Many thanksHi Khubkube,
Thanks for posting. If your bills are fully itemised you will see any chargeable calls listed on it since your previous bill. Unfortunately we can't offer you any information on incoming calls.
Cheers
David
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-) -
Incoming calls doesn't show on ios 5.0.1 on iPhone 4s
I bought iPhone 4s yesterday at T-Mobile Montengro, and I'm having problem with incoming and outgoing calls. All calls are show as number (not names from contacts) in Recants lists, and all incoming calls are the same. I have all my contacts stored in format +382 67 XXXXXX so they should work. My wife's iPhone 4 with ios 5.0 and same carrier work just fine.
I just ran into the same problem with an iPhone 4S: contact names and photos stopped showing up on incoming calls or in the recent/missed calls list. I took my phone to the Genius Bar and they ran a diagnostic to confirm there was nothing wrong with the phone hardware. Their suggestion, which worked:
Update iTunes to the latest version.
Sync your phone with your computer via iTunes. Make sure that the sync options are selected under each tab (Sync Contacts, Sync Apps, Sync Music, Sync Videos, etc..) so everything is backed up onto the computer.
In iTunes, select the Summary tab for the phone and click on Restore to wipe out the software and restore it.
When the system asks, restore as a new phone (instead of restoring from backup)
Once it's done, walk through the initial phone setup and re-sync your phone to get all of your contacts, apps, music, etc.
The explanation I got was that something in the software got corrupted and if I restored from a backup, the corruption would still be there, so I needed to restore it as a new phone and re-sync my data on to it. Bottom line is it worked, and I hope this saves some time and a trip to the Apple Store for you or anyone else that might run into this issue.
Good luck getting it resolved!
Kendrick -
HT201229 How can I access a list of incoming calls from a blocked number
How can I access a call log of incoming calls from a blocked number on my iphone?
Calls from blocked #'s won't go through, so they won't be listed on your device.
-
My incoming calls appears unknown even if they are in my contact list!
Hey!
My 8520 blackberry keeps showing unknown number when I already have them in my contact list. So if somebody can help, I will be very grateful.
Thank you,
AnaHello Anutzamaria
Welcome to BlackBerry Support Forums
Please refer to this Post incoming call appear as 'unknown number'
Good luck.
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it. -
Why do all my incoming calls show unknown, even when they are from people in my contact list?
Hi Hedland,
Thanks for visiting Apple Support Communities.
You may want to first check your caller ID settings, as mentioned in this article:
iPhone: Understanding phone features
http://support.apple.com/kb/HT4515
Caller ID
iPhone (GSM networks)
Turn on or off in Settings > Phone
iPhone (CDMA networks)
Contact your carrier for information on using Caller ID
If your settings are correct, try the troubleshooting steps in our iPhone Assistant:
http://www.apple.com/support/iphone/assistant/phone/
All the best,
Jeremy -
Q10 not answering incoming calls
Incoming calls go right to voicemail.
Subject Title edited to reflect new topic.OK. Well, that's a pretty ancient OS level...indeed, I don't think that's an OS version at all, but rather the "Software Release". Can you check again please?Article ID: KB23393 How to find the model number and OS version on a BlackBerry smartphoneFurther interesting is that you say you updated the software...strange that something so old would be an update, but I do not know what versions VZW has on their approved list, but that version is definitely quite old...maybe 25 or so updates behind what is truly current from BB. There were many more 10.2.1 releases, then 10.2.2, then 10.3.0, then 10.3.1, and now 10.3.2...each with several versions (at the 4th octet) within. Did you check, in the phone settings, the "Call Forwarding" items to make sure that none of those are set? Failing all of this, the only thing I could recommend is a clean OS reload, and to an OS level that is much more current. If the behavior continues after, then I'd say it's back to VZW to look even deeper into their system. Good luck!
-
Incoming Calls Sent Straight to Voice Mail
This problem seems to be linked to screen blanking. If I allow the screen to go dark by itself (after the preset number of seconds--30, in my case), all incoming phone calls will be sent direct to voice mail without ringing. I get a notice, then, if they leave a voice mail...but of course they have already hung up and I can't answer the call. People who don't leave a voice mail, I never know that they have called.
If I shut down the screen manually, phone calls ring as usual and I can anwer them. I have been to two different Verizon stores to have this checked out. They have removed the battery and reinstalled it, and also have reprogrammed a couple of times. They've also checked bunches of settings to be sure I haven't accidentally pressed a wrong button somewhere. Still, this happens. If I do not manually shut down the screen, I lose my incoming calls.
Any ideas? I love my phone and would hate to return it, but that may be my only option. I shouldn't have to manually shut off my screen after every operation in order to receive calls.slolife wrote:
This problem seems to be linked to screen blanking. If I allow the screen to go dark by itself (after the preset number of seconds--30, in my case), all incoming phone calls will be sent direct to voice mail without ringing. I get a notice, then, if they leave a voice mail...but of course they have already hung up and I can't answer the call. People who don't leave a voice mail, I never know that they have called.
If I shut down the screen manually, phone calls ring as usual and I can anwer them. I have been to two different Verizon stores to have this checked out. They have removed the battery and reinstalled it, and also have reprogrammed a couple of times. They've also checked bunches of settings to be sure I haven't accidentally pressed a wrong button somewhere. Still, this happens. If I do not manually shut down the screen, I lose my incoming calls.
Any ideas? I love my phone and would hate to return it, but that may be my only option. I shouldn't have to manually shut off my screen after every operation in order to receive calls.
If you have been to two different Verizon Wireless stores and your phone's concerns have not been resolved after our representatives did some troubleshooting steps, you may need to consider a phone replacement. Keep in mind that your phone includes a manufacturer’s warranty that will provide a Certified Like New Replacement phone identical to your current device. For more details please visit the link below:
Certified Like-New Replacement Program -
By incoming calls my iphone dos only vibrate (no tune) and it shows "blocked".How can I get back the tunes?
Greetings Nefertiti72,
It seems you are experiencing an issue with contact syncing and management. It seems you've removed an email account which contained a number of contacts that are not associated with your iCloud account. I have linked to a knowledge base article which provides more information about iCloud contacts syncing:
Get help using iCloud Contacts - Apple Support
Learn what to do if you’re having issues using iCloud Contacts. For example, you might make changes to Contacts that don't update across all of your devices.
You may want to consider importing the contacts from the email account you removed. You can do it easily by following the steps in this article:
iCloud: Import a vCard
You can import an electronic business card, also called a vCard, into iCloud Contacts. If the vCard contains contact information for more than one person, each contact becomes a separate entry.
In iCloud Contacts, choose Import vCard from the Action pop-up menu , which appears at the bottom of the All Contacts list or a list of group contacts
Select a vCard to import.
The contacts from the vCard are added to the All Contacts group in Contacts. You can add the contacts to any other group by dragging them to the desired group.
Thank you for contributing to Apple Support Communities.
Best,
Bobby_D -
CALLER ID not working for International incoming calls
Hi,
I've a strange issue where CALLER ID not working for International incoming calls, it shows INTERNATIONAL UNKNOWN NUMBER in the phone display, but the number shows correclty in Verizon Call assistant !!!
Any clue?yashshankar wrote:
Hi
I recently purschased an Online number but the caller id does not work for incoming calls.How do we resolve this problem?.
Regards
Yash
You didn't mention what country your Online Number is in. Not all of Skype's Online Numbers are eligible for use as Caller ID when calling telephones or sending SMS messages. If your number is from one of these countries (Chile, Denmark, Estonia, Hong Kong, Poland, Sweden, the UK and the US), then it can be used this way. Otherwise, you can use a mobile number from countries other than Japan or Mexico as Caller ID with Skype, after the number goes through a verification process where Skype sends SMS messages with codes to that number.
To get to these settings, log into your Skype account here on the Skype web site using the "Account" link at the top of this page. You'll see a screen that would include your current Caller ID settings, and a link to change that. If your Online Number is from one of those countries I referenced above, just select it and you're done.
Hope that helps!
Patrick
Location/Ubicacion: Arizona USA
Time Zone/Hora Local: UTC/GMT -7
If this message has adequately addressed your issue, please click on the “Accept as Solution” button. If you found a post useful then please "Give Kudos" at the bottom of my post, so that this information can benefit others.
Si esto mensaje le ha ayudado, por favor haga clic en "Aceptar como solución". Si encuentra un mensaje útil, por favor "Da Kudos" al final del mensaje, por lo que esta información puede beneficiar a otros.
I am not a Skype employee. No soy un empleado de Skype. -
Unity Express - Incoming calls wont get voice mail
CUE works fine with telephones on my local network. Incoming and outgoing calls work fine.
However when I get an incoming call via SIP trunk the call will not get forwarded to unity express after 10 seconds. The line goes dead.
I searched for another post which suggested the following commands:
telephony-service
call-forward pattern .T
voice service voip
allow connections from h323 to sip
I've double checked them and there's still something wrong.
Here's my current configuration:
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
h323
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
telephony-service
load 7910 P00403020214
load 7960-7940 P00305000301
max-ephones 24
max-dn 24
ip source-address 192.168.20.1 port 2000
auto assign 1 to 24
system message Comtek
voicemail 3000
max-conferences 8 gain -6
call-forward pattern .T
moh music-on-hold.au
time-webedit
transfer-system full-consult
transfer-pattern 2...
transfer-pattern 3...
directory last-name-first
directory entry 2 2001 name Phone Two 7912
directory entry 3 2000 name Phone One 7970
ephone-dn 1 dual-line
number 2000 secondary 441833000000
call-forward busy 3000
call-forward noan 3000 timeout 10
no huntstop
ephone 1
no multicast-moh
device-security-mode none
mac-address 0017.0EF0.3642
type 7970
button 1:1
So pros, any suggestions?
ThanksI made a new dial-peer to handle incoming calls as follows.
dial-peer voice 1000 voip
description Incoming SIP
translation-profile incoming SIPin
voice-class codec 1
session protocol sipv2
incoming called-number .T
dtmf-relay rtp-nte
no vad
The translation-profile puts the call through to my 2000 extension.
This is my "show call active voice brief" when an external incoming call is ringing through to my 2000 ephone-dn.
To me this seems to show the dial-peer "1000" matching and using the g711ulaw codec
Telephony call-legs: 1
SIP call-legs: 1
H323 call-legs: 0
Call agent controlled call-legs: 0
SCCP call-legs: 0
Multicast call-legs: 0
Total call-legs: 2
1715 : 552 596706500ms.1 +-1 pid:1000 Answer +441833696807 connecting
dur 00:00:00 tx:0/0 rx:0/0
IP 87.127.240.98:16188 SRTP: off rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms g711ulaw TextRelay: off
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
long duration call detected:n long duration call duration:n/a timestamp:n/a
1715 : 553 596706510ms.1 +-1 pid:20001 Originate 2000 connecting
dur 00:00:00 tx:0/0 rx:0/0
Tele 50/0/1 (553) [50/0/1.0] tx:0/0/0ms None noise:0 acom:0 i/0:0/0 dBm
Telephony call-legs: 1
SIP call-legs: 1
H323 call-legs: 0
Call agent controlled call-legs: 0
SCCP call-legs: 0
Multicast call-legs: 0
Total call-legs: 2
This is the "show call active voice brief" for an external incoming call when the call is established.
Telephony call-legs: 1
SIP call-legs: 1
H323 call-legs: 0
Call agent controlled call-legs: 0
SCCP call-legs: 0
Multicast call-legs: 0
Total call-legs: 2
1731 : 569 597220040ms.1 +3730 pid:1000 Answer +441833696807 active
dur 00:00:02 tx:105/16800 rx:104/16640
IP 87.127.240.98:15162 SRTP: off rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms g711ulaw TextRelay: off
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
long duration call detected:n long duration call duration:n/a timestamp:n/a
1731 : 570 597220060ms.1 +3700 pid:20001 Originate 2000 active
dur 00:00:02 tx:0/0 rx:105/16800
Tele 50/0/1 (570) [50/0/1.0] tx:16180/16180/0ms g711ulaw noise:0 acom:0 i/0:0/0 dBm
Telephony call-legs: 1
SIP call-legs: 1
H323 call-legs: 0
Call agent controlled call-legs: 0
SCCP call-legs: 0
Multicast call-legs: 0
Total call-legs: 2
Not too sure where to go from here. -
Hi Guys,
I have a SIP trunk setup with a 2811 running CME version 7. I can make outbound calls ok but having issues getting the incoming calls working, i have 1 number on my SIP trunk and that is 01133501788 and i want that to ring my Cisco 7960 which is running SIP firmware not SCCP. I have included by config for anyone who can help me, i just want the incoming call to work.
Many Thanks.
Matthew.
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone GMT 0
dot11 syslog
ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1
ip dhcp excluded-address 10.10.10.1
ip dhcp pool DATA_POOL
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 188.92.232.50 188.92.232.100
ip dhcp pool VOICE_POOL
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 188.92.232.50 188.92.232.100
option 150 ip 192.168.1.1
ip name-server 188.92.232.50
ip name-server 188.92.232.100
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
bind control source-interface FastEthernet0/1.20
bind media source-interface FastEthernet0/1.20
registrar server
voice class codec 1
codec preference 2 g711ulaw
codec preference 3 g711alaw
voice register global
mode cme
source-address 192.168.1.1 port 5060
max-dn 144
max-pool 42
load 7960-7940 P0S3-8-12-00
authenticate register
tftp-path flash:
create profile sync 0008072514198272
voice register dn 1
number 6999
allow watch
name SIP
label SIP
voice register pool 1
id mac 000F.902B.40E0
type 7960
number 1 dn 1
dtmf-relay sip-notify
username cisco password cisco
codec g711ulaw
voice translation-rule 1
rule 1 /^9\(.*\)/ /\1/
voice translation-rule 2
rule 1 /^6...$/ /4143*002/
voice translation-profile DiscardDigit9
translate calling 2
translate called 1
voice translation-profile IncomingSIP
translate calling 1133501788
voice-card 0
no dspfarm
username matt privilege 15 secret 5 $1$DCD0$SjWqnKgDSGVzzIKRerXh11
archive
log config
hidekeys
interface FastEthernet0/0
ip address 194.12.0.222 255.255.255.252
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1
no ip address
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1.10
description DATA
encapsulation dot1Q 10
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/1.20
description VOICE
encapsulation dot1Q 20
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 194.12.0.221
ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 1 interface FastEthernet0/0 overload
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 permit 10.10.10.0 0.0.0.255
tftp-server flash:P003-8-12-00.bin
tftp-server flash:P003-8-12-00.sbn
tftp-server flash:P0S3-8-12-00.loads
tftp-server flash:P0S3-8-12-00.sb2
tftp-server flash:P003-8-12-00
tftp-server flash:P003-8-12-00.loads
tftp-server flash:P003-8-12-00.sb2
tftp-server flash:SIP000F902B40E0.cnf.xml
control-plane
mgcp behavior g729-variants static-pt
dial-peer cor custom
dial-peer voice 2 voip
description Outgoing Geographic
translation-profile outgoing DiscardDigit9
destination-pattern 0[7]........
voice-class codec 1
session protocol sipv2
session target dns:sip.cloudcalling.co.uk
dtmf-relay rtp-nte
no vad
dial-peer voice 1 voip
description IncomingSIP
translation-profile incoming IncomingSIP
voice-class codec 1
session protocol sipv2
session target dns:sip.cloudcalling.co.uk
incoming called-number .T
dtmf-relay sip-notify rtp-nte
no vad
sip-ua
credentials username 4143*002 password 7 password realm sip.cloudcalling.co.uk
authentication username 4143*002 password 7 password
nat symmetric role passive
nat symmetric check-media-src
calling-info sip-to-pstn number set 4143*002
no remote-party-id
retry invite 3
retry register 3
timers connect 100
registrar dns:sip.cloudcalling.co.uk expires 60
sip-server dns:sip.cloudcalling.co.uk
host-registrar
gatekeeper
shutdown
telephony-service
load 7960-7940 P0S3-8-12-00
max-ephones 24
max-dn 30
ip source-address 192.168.1.1 port 2000
max-conferences 8 gain -6
web admin system name Admin secret 5 $1$Fktw$t9GQkdDdHmoYdwptO8.or.
transfer-system full-consult
create cnf-files version-stamp Jan 01 2002 00:00:00
line con 0
line aux 0
line vty 0 4
login
scheduler allocate 20000 1000
ntp server 85.119.80.232
end
Router#You my friend are a star! worked straight away, many thanks. Just one more thing, when i make an outgoing call, it always appears as "blocked" on my phone, my sip trunk is set to allow CME to alter outgoing CLI's how would i program the outgoing CLI to 01133501788 also?
The new working config is below with your suggestion, which works!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone GMT 0
dot11 syslog
ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1
ip dhcp excluded-address 10.10.10.1
ip dhcp pool DATA_POOL
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 188.92.232.50 188.92.232.100
ip dhcp pool VOICE_POOL
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 188.92.232.50 188.92.232.100
option 150 ip 192.168.1.1
ip name-server 188.92.232.50
ip name-server 188.92.232.100
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
registrar server
voice class codec 1
codec preference 2 g711ulaw
codec preference 3 g711alaw
voice register global
mode cme
source-address 192.168.1.1 port 5060
max-dn 144
max-pool 42
load 7960-7940 P0S3-8-12-00
authenticate register
tftp-path flash:
create profile sync 0015244443466064
voice register dn 1
number 6999
allow watch
name SIP
label SIP
voice register pool 1
id mac 000F.902B.40E0
type 7960
number 1 dn 1
dtmf-relay sip-notify
username cisco password cisco
codec g711ulaw
voice translation-rule 1
rule 1 /^6...$/ /4143*002/
voice translation-rule 3
rule 1 /^01133501788$/ /6999/
rule 2 /^1133501788$/ /6999/
voice translation-profile IncomingSIP
translate called 3
voice translation-profile Translatetrunk
translate calling 1
voice-card 0
no dspfarm
username matt privilege 15 secret 5 $1$DCD0$SjWqnKgDSGVzzIKRerXh11
archive
log config
hidekeys
interface FastEthernet0/0
ip address 194.12.0.222 255.255.255.252
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1
no ip address
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/1.10
description DATA
encapsulation dot1Q 10
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/1.20
description VOICE
encapsulation dot1Q 20
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 194.12.0.221
ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 1 interface FastEthernet0/0 overload
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 permit 10.10.10.0 0.0.0.255
tftp-server flash:P003-8-12-00.bin
tftp-server flash:P003-8-12-00.sbn
tftp-server flash:P0S3-8-12-00.loads
tftp-server flash:P0S3-8-12-00.sb2
tftp-server flash:P003-8-12-00
tftp-server flash:P003-8-12-00.loads
tftp-server flash:P003-8-12-00.sb2
tftp-server flash:SIP000F902B40E0.cnf.xml
control-plane
mgcp behavior g729-variants static-pt
dial-peer cor custom
dial-peer voice 1 voip
description IncomingSIP
translation-profile incoming IncomingSIP
voice-class codec 1
session protocol sipv2
session target sip-server
incoming called-number .T
dtmf-relay sip-notify rtp-nte
no vad
dial-peer voice 2 voip
description Outgoing Geographic
translation-profile outgoing Translatetrunk
destination-pattern 0[7]........
voice-class codec 1
session protocol sipv2
session target dns:sip.cloudcalling.co.uk
dtmf-relay rtp-nte
no vad
sip-ua
credentials username 4143*002 password 7 password realm sip.cloudcalling.co.uk
authentication username 4143*002 password 7 password
nat symmetric role passive
nat symmetric check-media-src
calling-info sip-to-pstn number set 4143*002
no remote-party-id
retry invite 3
retry register 3
timers connect 100
registrar dns:sip.cloudcalling.co.uk expires 60
sip-server dns:sip.cloudcalling.co.uk
host-registrar
gatekeeper
shutdown
telephony-service
load 7960-7940 P0S3-8-12-00
max-ephones 24
max-dn 30
ip source-address 192.168.1.1 port 2000
max-conferences 8 gain -6
web admin system name Admin secret 5 $1$Fktw$t9GQkdDdHmoYdwptO8.or.
transfer-system full-consult
create cnf-files version-stamp 7960 Dec 17 2013 14:35:13
line con 0
line aux 0
line vty 0 4
login
scheduler allocate 20000 1000
ntp server 85.119.80.232
end
Router# -
SIP incoming call, won't work (CME)
Hi all,
I'm facing a weird problem and the sip-provider can't help. I suppose there is a problem with the dial-peer/translation-rule but I can't figure it out...
There is a CME (c2800nm-ipvoice-mz.124-11.XW10.bin, CME Version 4.2(0)) with a
SIP trunk.
Outgoing calls are working (DID).
Incoming calls (all DID) are ringing on the same internal number.
The situation:
- external call on 0815440097 is ringing on the internal nr. 296 (should be 297)
- external call on 0815440096 is ringing on the internal nr. 296
Here the config:
================================
voice service voip
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
no update-callerid
voice translation-rule 40
rule 2 /\(.*\)/ /9\1/
voice translation-rule 190
rule 1 /^0\(.*\)/ /\1/
rule 2 /^9\(.*\)/ /\1/
voice translation-rule 191
rule 2 /296/ /0815440096/
rule 3 /297/ /0815440097/
voice translation-rule 192
rule 2 /^0815440097/ /297/
rule 3 /^0815440096/ /296/
voice translation-profile TP_IN_SIP
translate calling 40
translate called 192
voice translation-profile TP_OUT_SIP
translate calling 191
translate called 190
dial-peer voice 2000 voip
description *** SIP-TRUNK (IN/OUT) ***
translation-profile incoming TP_IN_SIP
translation-profile outgoing TP_OUT_SIP
destination-pattern 0.T
b2bua
session protocol sipv2
session target dns:sip12.e-fon.ch
session transport udp
incoming called-number 0815440096
dtmf-relay rtp-nte
codec g711alaw
no vad
sip-ua
credentials username 0815440096 password 7 xxxx realm sip12.e-fon.ch
keepalive target dns:sip12.e-fon.ch
authentication username 0815440096 password 7 xxxx
calling-info pstn-to-sip from number set 0815440096
no remote-party-id
retry invite 2
retry response 2
retry bye 2
retry register 2
retry options 1
registrar dns:sip12.e-fon.ch expires 69
sip-server dns:sip12.e-fon.ch
reason-header override
connection-reuse
host-registrar
sh sip-ua register status
Line peer expires(sec) registered
================================ ========== ============ ==========
0815440096 20005 18 yes
Here the CCSIP MESSAGE debug (looks ok):
(call from 0000000000 to 0815440097)
===============================
Mar 8 21:55:10.469 METD: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
INVITE sip:[email protected]:5060 SIP/2.0
Record-Route: <sip:212.55.198.132;lr=on;ftag=as00cd0e7f>
Via: SIP/2.0/UDP 212.55.198.132;branch=z9hG4bK49ff.2d35e30a71291ffe3895b39164900f36.0
Via: SIP/2.0/UDP 212.55.198.134:5061;branch=z9hG4bK1cb84749;rport=5061
Max-Forwards: 69
From: "0000000000" <sip:[email protected]:5061>;tag=as00cd0e7f
To: <sip:[email protected]:5060>
Contact: <sip:[email protected]:5061>
Call-ID: [email protected]
CSeq: 102 INVITE
User-Agent: e-fon
Date: Thu, 08 Mar 2012 20:55:10 GMT
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY, INFO
Supported: replaces, timer
X-IPCONNECT: 0815440097
X-Number: 0815440097
Content-Type: application/sdp
Content-Length: 415
v=0
o=root 770254981 770254981 IN IP4 212.55.198.134
s=Asterisk PBX 1.6.1.20
c=IN IP4 212.55.198.134
t=0 0
m=audio 11886 RTP/AVP 8 9 111 3 18 0 101
a=rtpmap:8 PCMA/8000
a=rtpmap:9 G722/8000
a=rtpmap:111 G726-32/8000
a=rtpmap:3 GSM/8000
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=no
a=rtpmap:0 PCMU/8000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-16
a=silenceSupp:off - - - -
a=ptime:20
a=sendrecv
Mar 8 21:55:10.481 METD: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP 212.55.198.132;branch=z9hG4bK49ff.2d35e30a71291ffe3895b39164900f36.0,
Via:SIP/2.0/UDP 212.55.198.134:5061;branch=z9hG4bK1cb84749;rport=5061
From: "0000000000" <sip:[email protected]:5061>;tag=as00cd0e7f
To: <sip:[email protected]:5060>
Date: Thu, 08 Mar 2012 20:55:10 GMT
Call-ID: [email protected]
Server: Cisco-SIPGateway/IOS-12.x
CSeq: 102 INVITE
Allow-Events: telephone-event
Content-Length: 0
Here is the VOICE DIAL-PEER debug (call from 0000000000 to 0815440097):
=============================================
Mar 8 22:00:09.498 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
Calling Number=0815440096, Called Number=0815440096, Peer Info
Type=DIALPEER_INFO_SPEECH
Mar 8 22:00:09.498 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
Match Rule=DP_MATCH_DEST; Called Number=0815440096
Mar 8 22:00:09.498 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
Result=Success(0) after DP_MATCH_DEST
Mar 8 22:00:09.498 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:
Result=SUCCESS(0)
List of Matched Outgoing Dial-peer(s):
1: Dial-peer Tag=20005
2: Dial-peer Tag=2000
Mar 8 22:00:09.498 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Calling Number=0000000000, Called Number=, Voice-Interface=0x0,
Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,
Peer Info Type=DIALPEER_INFO_SPEECH
Mar 8 22:00:09.498 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Result=Success(0) after DP_MATCH_ORIGINATE; Incoming Dial-peer=2000
Mar 8 22:00:09.502 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Calling Number=0000000000, Called Number=, Voice-Interface=0x0,
Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,
Peer Info Type=DIALPEER_INFO_SPEECH
Mar 8 22:00:09.502 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Result=Success(0) after DP_MATCH_ORIGINATE; Incoming Dial-peer=2000
Mar 8 22:00:09.502 METD: //-1/8647979A82E1/DPM/dpAssociateIncomingPeerCore:
Calling Number=0000000000, Called Number=0815440096, Voice-Interface=0x0,
Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,
Peer Info Type=DIALPEER_INFO_SPEECH
Mar 8 22:00:09.502 METD: //-1/8647979A82E1/DPM/dpAssociateIncomingPeerCore:
Result=Success(0) after DP_MATCH_ORIGINATE; Incoming Dial-peer=2000
Mar 8 22:00:09.510 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
Calling Number=0815440096, Called Number=0815440096, Peer Info
Type=DIALPEER_INFO_SPEECH
Mar 8 22:00:09.510 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
Match Rule=DP_MATCH_DEST; Called Number=0815440096
Mar 8 22:00:09.510 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:
Result=Success(0) after DP_MATCH_DEST
Mar 8 22:00:09.510 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:
Result=SUCCESS(0)
List of Matched Outgoing Dial-peer(s):
1: Dial-peer Tag=20006
2: Dial-peer Tag=2000
Mar 8 22:00:09.510 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Calling Number=0815440096, Called Number=, Voice-Interface=0x0,
Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,
Peer Info Type=DIALPEER_INFO_SPEECH
Mar 8 22:00:09.510 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Result=Success(0) after DP_MATCH_ANSWER; Incoming Dial-peer=2000
Mar 8 22:00:09.514 METD: //-1/8647979A82E1/DPM/dpMatchPeersCore:
Calling Number=, Called Number=0815440096, Peer Info
Type=DIALPEER_INFO_SPEECH
Mar 8 22:00:09.514 METD: //-1/8647979A82E1/DPM/dpMatchPeersCore:
Match Rule=DP_MATCH_DEST; Called Number=0815440096
Mar 8 22:00:09.514 METD: //-1/8647979A82E1/DPM/dpMatchPeersCore:
Result=Success(0) after DP_MATCH_DEST
Mar 8 22:00:09.514 METD: //-1/8647979A82E1/DPM/dpMatchPeersMoreArg:
Result=SUCCESS(0)
List of Matched Outgoing Dial-peer(s):
1: Dial-peer Tag=20006
2: Dial-peer Tag=2000
show dial-peer voice summary:
dial-peer hunt 0
AD PRE PASS OUT
TAG TYPE MIN OPER PREFIX DEST-PATTERN FER THRU SESS-TARGET STAT
PORT
555 voip up up 555 0 syst loopback:rtp
20001 pots up up 296$ 0 50/0/1
20002 pots up up 297$ 0 50/0/2
2000 voip up up 0.T 0 syst dns:sip12.e-fon.ch
20005 pots up up 0815440096$ 0 50/0/150
20006 pots up up 0815440097$ 9 50/0/2
voip translation debugging (call from 0794142975 to 0815440097):
=========================================
Mar 8 22:35:26.145 METD: //-1/73E51DB2834F/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x46FBFCA0; count=1
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x46FBFCA0; count=0
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_profile_translate_internal: number=0794142975 type=unknown plan=unknown numbertype=calling
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_profile_match_internal: Matched with rule 2 in ruleset 40
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_profile_match_internal: Matched with rule 2 in ruleset 40
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/sed_subst: Successful substitution; pattern=0794142975 matchPattern=(.*) replacePattern=9\1 replaced pattern=90794142975
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_subst_num_type: Match Type = none, Replace Type = none Input Type = unknown
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_subst_num_plan: Match Plan = none, Replace Plan = none Input Plan = unknown
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_profile_translate_internal: xlt_number=90794142975 xlt_type=unknown xlt_plan=unknown
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_profile_translate_internal: number= type=unknown plan=unknown numbertype=redirect-called
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_get_RegXrule: Invalid translation ruleset tag=0
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_profile_match_internal: Error: ruleset for redirect-called number not found
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_profile_translate_internal: No match: number= type=unknown plan=unknown
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_profile_translate_internal: number=0815440096 type=unknown plan=unknown numbertype=called
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_match: No match; number=0815440096 rule precedence=2
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_match: No match; number=0815440096 rule precedence=3
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_profile_match_internal: No match found
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_profile_translate_internal: No match: number=0815440096 type=unknown plan=unknown
Mar 8 22:35:26.149 METD: //-1/73E51DB2834F/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x46FBFCA0; count=1
Mar 8 22:35:26.153 METD: //-1/73E51DB2834F/RXRULE/regxrule_dp_translate: No profile found in peer 20005 for outgoing direction
Mar 8 22:35:26.153 METD: //-1/73E51DB2834F/RXRULE/regxrule_dp_translate: calling_number=90794142975 calling_octet=0x0
called_number=0815440096 called_octet=0x0
redirect_number= redirect_type=0 redirect_plan=0 redirect_PI=-1 redirect_SI=-1
Mar 8 22:35:26.181 METD: //-1/73E51DB2834F/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x46FBFCA0; count=2
Thanks,
NorbertHi Alex,
Thank you for the reply.
After changing the "incoming called-number" I got the same output.
The weird think is, why the dial-peer debug shows the 0815440096 number, despite the right "to: number" in the SIP-Message.
Is there a problem with the "voice service voip" or "sip-ua"?
on the voice translation debug I see:
Match Rule=DP_MATCH_TO_URI; URI=sip:0815440097
Match Rule=DP_MATCH_FROM_URI; URI=sip:0819262424
But I guess the translation rule is maching this one:
Match Rule=DP_MATCH_INCOMING_DNIS; Called Number=0815440096
So how can the voice translation rule be set to map the entry DP_MATCH_TO_URI; URI=sip:0815440097
Thanks for the help.
Regards,
Norbert
voip translation debugging (call from 0819262424 to 0815440097):
===================================================
Mar 9 07:45:16.371 METD: //-1/439ABF97847F/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x46FBFAFC; count=1
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x46FBFAFC; count=0
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_profile_translate_internal: number=0819262424 type=unknown plan=unknown numbertype=calling
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_profile_match_internal: Matched with rule 2 in ruleset 40
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_profile_match_internal: Matched with rule 2 in ruleset 40
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/sed_subst: Successful substitution; pattern=0819262424 matchPattern=(.*) replacePattern=9\1 replaced pattern=90819262424
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_subst_num_type: Match Type = none, Replace Type = none Input Type = unknown
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_subst_num_plan: Match Plan = none, Replace Plan = none Input Plan = unknown
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_profile_translate_internal: xlt_number=90819262424 xlt_type=unknown xlt_plan=unknown
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_profile_translate_internal: number= type=unknown plan=unknown numbertype=redirect-called
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_get_RegXrule: Invalid translation ruleset tag=0
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_profile_match_internal: Error: ruleset for redirect-called number not found
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_profile_translate_internal: No match: number= type=unknown plan=unknown
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_profile_translate_internal: number=0815440096 type=unknown plan=unknown numbertype=called
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_match: No match; number=0815440096 rule precedence=2
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_profile_match_internal: Matched with rule 3 in ruleset 192
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_match: No match; number=0815440096 rule precedence=2
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_profile_match_internal: Matched with rule 3 in ruleset 192
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_match: No match; number=0815440096 rule precedence=2
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/sed_subst: Successful substitution; pattern=0815440096 matchPattern=^0815440096 replacePattern=296 replaced pattern=296
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_subst_num_type: Match Type = none, Replace Type = none Input Type = unknown
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_subst_num_plan: Match Plan = none, Replace Plan = none Input Plan = unknown
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_profile_translate_internal: xlt_number=296 xlt_type=unknown xlt_plan=unknown
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x46FBFAFC; count=1
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_dp_translate: No profile found in peer 20001 for outgoing direction
Mar 9 07:45:16.375 METD: //-1/439ABF97847F/RXRULE/regxrule_dp_translate: calling_number=90819262424 calling_octet=0x0
called_number=296 called_octet=0x0
redirect_number= redirect_type=0 redirect_plan=0 redirect_PI=-1 redirect_SI=-1
Mar 9 07:45:16.379 METD: //-1/439ABF97847F/RXRULE/regxrule_vp_translate: No profile found in voice port or trunk group for outgoing direction
Mar 9 07:45:16.379 METD: //-1/439ABF97847F/RXRULE/regxrule_vp_translate: calling_number=90819262424 calling_octet=0x0
called_number=296 called_octet=0x0
redirect_number= redirect_type=0 redirect_plan=0
Mar 9 07:45:18.195 METD: //-1/439ABF97847F/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x46FBFAFC; count=2
debug voice dialpeer detail
=====================
Mar 9 07:49:25.572 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=0815440096, Expanded String=0815440096, Calling Number=0815440096T
Timeout=TRUE, Is Incoming=FALSE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.572 METD: //-1/xxxxxxxxxxxx/DPM/MatchNextPeer:
Result=Success(0); Outgoing Dial-peer=2000 Is Matched
Mar 9 07:49:25.572 METD: //-1/xxxxxxxxxxxx/DPM/MatchNextPeer:
Result=Success(0); Outgoing Dial-peer=20005 Is Matched
Mar 9 07:49:25.572 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_ANSWER; Calling Number=0819262424
Mar 9 07:49:25.572 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.572 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=, Expanded String=, Calling Number=0819262424T
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.572 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Result=-1
Mar 9 07:49:25.572 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_ORIGINATE; Calling Number=0819262424
Mar 9 07:49:25.572 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.572 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=, Expanded String=, Calling Number=0819262424T
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.572 METD: //-1/xxxxxxxxxxxx/DPM/MatchNextPeer:
Result=Success(0); Incoming Dial-peer=2000 Is Matched
Mar 9 07:49:25.576 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_ANSWER; Calling Number=0819262424
Mar 9 07:49:25.576 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.576 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=, Expanded String=, Calling Number=0819262424T
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.576 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Result=-1
Mar 9 07:49:25.576 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_ORIGINATE; Calling Number=0819262424
Mar 9 07:49:25.576 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.576 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=, Expanded String=, Calling Number=0819262424T
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.576 METD: //-1/xxxxxxxxxxxx/DPM/MatchNextPeer:
Result=Success(0); Incoming Dial-peer=2000 Is Matched
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_REQUEST_URI; URI=sip:[email protected]:5060
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchCore:
Dial String=, Expanded String=, Calling Number=
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchCore:
Result=-1
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_TO_URI; URI=sip:[email protected]:5060
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchCore:
Dial String=, Expanded String=, Calling Number=
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchCore:
Result=-1
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_FROM_URI; URI=sip:[email protected]:5061
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchCore:
Dial String=, Expanded String=, Calling Number=
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchCore:
Result=-1
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_INCOMING_DNIS; Called Number=0815440096
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchCore:
Dial String=0815440096, Expanded String=0815440096, Calling Number=
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchCore:
Result=-1
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_ANSWER; Calling Number=0819262424
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchCore:
Dial String=, Expanded String=, Calling Number=0819262424T
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchCore:
Result=-1
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_ORIGINATE; Calling Number=0819262424
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/dpMatchCore:
Dial String=, Expanded String=, Calling Number=0819262424T
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.576 METD: //-1/D8245087848D/DPM/MatchNextPeer:
Result=Success(0); Incoming Dial-peer=2000 Is Matched
Mar 9 07:49:25.584 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=296, Expanded String=296, Calling Number=296T
Timeout=TRUE, Is Incoming=FALSE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.584 METD: //-1/xxxxxxxxxxxx/DPM/MatchNextPeer:
Result=Success(0); Outgoing Dial-peer=20001 Is Matched
Mar 9 07:49:25.584 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_ANSWER; Calling Number=296
Mar 9 07:49:25.584 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.584 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=, Expanded String=, Calling Number=296T
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.584 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Result=-1
Mar 9 07:49:25.584 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_ORIGINATE; Calling Number=296
Mar 9 07:49:25.584 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.584 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=, Expanded String=, Calling Number=296T
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.584 METD: //-1/xxxxxxxxxxxx/DPM/MatchNextPeer:
Result=Success(0); Incoming Dial-peer=20001 Is Matched
Mar 9 07:49:25.584 METD: //-1/D8245087848D/DPM/dpMatchCore:
Dial String=296, Expanded String=296, Calling Number=
Timeout=TRUE, Is Incoming=FALSE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.584 METD: //-1/D8245087848D/DPM/MatchNextPeer:
Result=Success(0); Outgoing Dial-peer=20001 Is Matched
Mar 9 07:49:25.588 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=90819262424, Expanded String=90819262424, Calling Number=
Timeout=TRUE, Is Incoming=FALSE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.588 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Result=-1
Mar 9 07:49:25.592 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=0819262424, Expanded String=0819262424, Calling Number=
Timeout=TRUE, Is Incoming=FALSE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.592 METD: //-1/xxxxxxxxxxxx/DPM/MatchNextPeer:
Result=Success(0); Outgoing Dial-peer=2000 Is Matched
Mar 9 07:49:25.592 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_ANSWER; Calling Number=296
Mar 9 07:49:25.592 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.592 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=, Expanded String=, Calling Number=296T
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.592 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Result=-1
Mar 9 07:49:25.596 METD: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
Match Rule=DP_MATCH_ORIGINATE; Calling Number=296
Mar 9 07:49:25.596 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchPeertype:
Is Incoming=TRUE, Number Expansion=FALSE
Mar 9 07:49:25.596 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=, Expanded String=, Calling Number=296T
Timeout=TRUE, Is Incoming=TRUE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.596 METD: //-1/xxxxxxxxxxxx/DPM/MatchNextPeer:
Result=Success(0); Incoming Dial-peer=20001 Is Matched
Mar 9 07:49:25.596 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=296, Expanded String=296, Calling Number=
Timeout=TRUE, Is Incoming=FALSE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.596 METD: //-1/xxxxxxxxxxxx/DPM/MatchNextPeer:
Result=Success(0); Outgoing Dial-peer=20001 Is Matched
Mar 9 07:49:25.596 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=90819262424, Expanded String=90819262424, Calling Number=
Timeout=TRUE, Is Incoming=FALSE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.596 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Result=-1
Mar 9 07:49:25.596 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=90819262424, Expanded String=90819262424, Calling Number=
Timeout=TRUE, Is Incoming=FALSE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.596 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Result=-1
Mar 9 07:49:25.596 METD: //-1/xxxxxxxxxxxx/DPM/dpMatchCore:
Dial String=296, Expanded String=296, Calling Number=
Timeout=TRUE, Is Incoming=FALSE, Peer Info Type=DIALPEER_INFO_SPEECH
Mar 9 07:49:25.596 METD: //-1/xxxxxxxxxxxx/DPM/MatchNextPeer:
Result=Success(0); Outgoing Dial-peer=20001 Is Matched
Maybe you are looking for
-
E70 PDF Reader : Unable to open. File type not sup...
This morning I have bought an E70, among others due to its highscreen resolution and the possibility to run a PDF reader on it. I have now tried ... - the pre-installed Adobe PDF Reader - the Adobe PDF Reader supplied with the PC Suite CD-ROM -
-
Keep getting - the disk could not be read or written to
Had my itouch for just over a week now and updated to 3.1.2 and i was able to sync it once. Now everytime i try to sync i get. the ipod cannot be synced. the disk cannot be read or writtin to. Any suggestions? Im very new to the Apple products. Thank
-
I have a Iphone 3g,every now and then some of my music will disappear then reappear.I've tried to sync the music from my library on my laptop,nothing happens.How do I get my music back,without having to wait for it to reappear?
-
Updating fireworks impossible !
Adobe application manager prevents me from reaching the server. Says must be a problem with the internet connection or the firewall settings. Actually, both don't fit. I've fireworks on a laptop and never encountered such problems, even from the same
-
Once an option is clicked in a rating scale it can't be unclicked. Does anyone know of a way to set up the scale so that a contributor can change their mind and unclick?