Listening to an audiobook when it started repeating just 2 words over and over again and I can't stop it
How can I make my ipod return to normal. It just keeps on repeating 2 words over and over again?
Turn on iPod touch. Press and hold the Sleep/Wake button until the Apple logo appears.
•• Open Camera when iPod touch is locked: Press the Sleep/Wake button or the Home button,
then drag up.
•• Access the audio controls when iPod touch is locked: Swipe up from the bottom edge of the
screen to open Control Center.
Unlock iPod touch. Press the Sleep/Wake button or the Home button, then drag the slider.
Turn off iPod touch. Press and hold the Sleep/Wake button until the red slider appears, then drag
the slider.
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Unsync/delete the audio books and resync
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
Similar Messages
-
Firefox crashes quite often, especially when I have multi tabs open. I usually have to use CTRL ALT DEL and end the process as Firefox stops responding.
My problem is not the crashing........it is the re-opening of the multiple tabs I had open, when normally it is one of them (not the home page) that caused the crash in the first place, so I cannot re-open firefox until I restart the pc, because every time I do it is the same story. Firefox tries to re-open all of the tabs and stops responding. I have looked in options but nowhere does it allow me to stop multiple tabs opening after a crash. If this continues, I will have to uninstall Firefox and stick to Chrome.Set the pref browser.sessionstore.max_resumed_crashes to 0 on the about:config page to get the about:sessionrestore page immediately with the first restart after a crash has occurred or the Task Manager was used to close Firefox.
*http://kb.mozillazine.org/browser.sessionstore.max_resumed_crashes
That will allow you to deselect the tab(s) that you do not want to reopen, but will allow to reopen other tabs.
See:
* http://kb.mozillazine.org/Session_Restore#Restoring_a_session_after_a_crash
* http://kb.mozillazine.org/Browser.sessionstore.max_resumed_crashes
To open the <i>about:config</i> page, type <b>about:config</b> in the location (address) bar and press the "<i>Enter</i>" key, just like you type the url of a website to open a website.<br />
If you see a warning then you can confirm that you want to access that page.<br />
*Use the Filter bar at to top of the about:config page to locate a preference more easily.
*Preferences that have been modified show as bold (user set).
*Preferences can be reset to the default or changed via the right-click context menu. -
Why does TDM Importer start up when I open an Excel file in LabVIEW, and how can I stop it?
I have a new application using LabVIEW 2012 SP1. I open an Excel file using the Report Generation toolkit and when I do so, a small TDM Importer window pops up on top of the Excel file.
How can I prevent this?Hi Steve,
The TDM Importer pops up because the report generated in LabVIEW is in the TDMS file format. TDMS is a binary file that requires an importer to make sense of the binary data and translate it into an Excel spreadsheet. As per this white paper, the appearance of the floating toolbar is expected behavior: http://www.ni.com/white-paper/5874/en/
To the best of my knowledge, you cannot get rid of the floating toolbar unless you uninstall the add-in, in which case you probably would not be able to open your LabVIEW-generated reports. However, as of Excel 2007, the toolbar is embedded in the "Add-Ins" tab instead of floating on your spreadsheet. You can see how the toolbar looks as of Excel 2007 in step 6 of this white paper: http://www.ni.com/white-paper/5885/en/
If there is a way to embed the toolbar in Excel 2003, it would be the exact same way you would embed any other floating customer toolbar in Excel. In other words, I don't think this has anything to do with the fact that it's NI's add-in. This is just the way Excel 2003 and earlier treats add-in toolbars. Someone on these forums may well know a way to embed it (perhaps a macro?), but you may have better luck contacting Microsoft. I'm not sure whether it's even possible for a user to embed the toolbar.
David R
Applications Engineer
National Instruments -
Firefox keeps freezing up and giving me the colorful spinning wheel especially when I'm chatting with a friend of facebook or when i'm listening to music on myspace or even have just two tabs open and it's never done it before but now it just keeps giving me the colorful spinning wheel and i have to force quit and start over.
== This happened ==
Every time Firefox opened
== May 5th, 2010Hi If you get an error message saying your flash is blocked by firewall or needs updating or similar and you just get the spinning colour wheel try this link
It takes you to Adobe which tells you which ver of flash player you have - you can then see if there is a later ver by clicking on the library and it automatically selects the correct version for you to download.
Worked a treat for me! Good Luck
http://www.adobe.com/software/flash/about/
Ps Don't forget to use a browser other than firefox or you will be there for days. -
When I try and open Microsoft Word 2011 documents on my IMAC they start opening one after another at a rapid speed and I can't stop it. I reboot and same thing happens. The documents open in rapid succession on their own and don't stop until I force close or after maybe 100 or more open I start getting the following message for each document attemting to open "This document could not be registered. It will not be possible to create links from other documents to this document" and then in paretheses the name of the document. After I click okay another trys to open. Any suggestions?
If you had multiple documents open and quit the app without closing all of the docs first, it will open them again when you launch the app. Open Word, and then close all the documents, you may be asked to save the document, if the document was already saved but you made changes to it before you quit the app, you may need to save the changes first, shorcut ( command and s keys). After you close all of the documents then quit the app and restart the computer. See if this works.
-
After having shut down after installing updates, when I restarted and tried to open a word doc, it started opening ALL the word docs and the only way I could stop it was by"force quit" . This is REALLY annoying!!
May be it is the Resume feature.
System Preference > General > Number of recent items
Uncheck the box next to "Restore windows when quitting and re-opening apps".
Best. -
I updated Itunes today to the latest version. Windows 7 64bit. None of my drivers work and get an error when itunes starts, about registry setting for reading and writing dvds and cds missing. Anyone else have the same issue. I downloaded itunes again, reinstalled still have same issue.
I'd start with the following document, with one modification. At step 12 after typing GEARAspiWDM press the Enter/Return key once prior to clicking OK. (Pressing Return adds a carriage return in the field and is important.)
iTunes for Windows: "Registry settings" warning when opening iTunes -
When I start MacBook Pro13 shows gray Screen and flashing file Image with question mark
When I start MacBook Pro13 shows gray Screen and flashing file Image with question mark , it's brand new I just receive it from Apple Store .
Startup Manager to select Startup disk.
http://support.apple.com/kb/HT1310
Repair Disk
Steps 2 through 8
http://support.apple.com/kb/PH5836 -
I recently purchased Aperture from App store and this was running fine until I upgraded to Mountain Lion. Now when I start Aperture it asks me for a Serial Number . Where can I find this as it was a download and I have no packaging?
I also have this problem! Mine is also not from the App Store. I had purchased Aperture 1, then upgrades for both version 2 and version 3. It's annoying as it is, but I also have to enter my previous serial number as well since it was an upgrade.
Following this thread in the hopes that someone will have a solution. -
Why does CS6 automatically start when i plug in my Canon Eos camera and how do I stop it
Why does CS6 automatically start when i plug in my Canon Eos camera and how do I stop it from doing so?
Autostart is controlled by your operating system. check the relevant system control panel or right-click the drive letter of your memory card to change these options in teh properties.
Mylenium -
Hey ppl,my macbook is not booting and by that i mean u can hear the audio wave when its starting up,the screen goes white and then after a while there's a folder with a question mark in the middle of the screen...anyone,any ideea?!?Regards.
That folder with the question mark icon means that the MacBook can't find the boot directory. That can either mean it can't find the hard drive or the hard drive data is somehow corrupted.
Put your install DVD into the drive and reboot. As soon as you hear the boot chime, hold down the "c" key on your keyboard (or the Option key until the Install Disk shows up). That will force your MacBook to boot from the optical drive.
Once it has finished booting and you are at the Install screen launch Disk Utility from the Utilities menu. Is your Hard Drive in the list on the left?
If it is then select the First Aid Tab run Repair Disk and if that repairs any problems run it again until the green OK appears and then run Repair Permissions.
If your hard drive isn’t recognized in Disk Utility then your hard drive is probably dead. -
When I start PS Elements 11 editor, I get this message: "This program can't start because MSVCRT10.d
When I start PS Elements 11 editor, I get this message: "This program can't start because MSVCRT10.dll is missing from your computer. Try reinstalling this program to fix this problem."
When I try to dismiss the error dialogue box, the message reappears immediately and the program does not load. After dismissing the dialogue 8 or 10 or 12 times, the editor finally loads and everything works okay.
How may I solve this frustrating problem? I've already uninstalled and reinstalled the program and that hasn't solved the issue. If I need to add a .dll file to my machine, where do I locate it and where do I place it on my computer?
Thanks
William DriverUsing Holmesian deductive skills and Spadian investigative techniques, I discovered that the problem lay in a third party filter application. I determined that since the program gave me the error message when PSE 11 began its scan for filter plugins, then the problem might lie there. I removed the filter plugins from the program's 'Plugins' directory to a another folder and added them back one by one until I got the error message. Sure enough, I eventually located the faulty plugins and removed them. Now PSE 11 loads without a problem.
Thanks for your help. -
I am using I Photo 4.0.3. When I start it, loading pictures never ends and I cannot use I Photo; What can I do?
When did this begin? Did you run any updaters just before this began and, if so, what were they?
That's a very old iPhoto version so give this a try:
1 - launch iPhoto with the Command+Option keys held down.
2 - select Options #3 and #4.
4 - Rebuild the library.
If that fails to help continue with this:
Using iPhoto Library Manager to Rebuild Your iPhoto Library
Download iPhoto Library Manager and launch.
Click on the Add Library button,
navigate to your Home/Pictures folder and select your iPhoto Library folder.
Now that the library is listed in the left hand pane of iPLM, click on your library and go to the Library ➙ Rebuild Library menu option
In the next window name the new library and select the location you want it to be placed.
Click on the Create button.
Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments. However, books, calendars, cards and slideshows will be lost. The original library will be left untouched for further attempts at fixing the problem or in case the rebuilt library is not satisfactory.
OT -
I rented a movie directly from Apple TV. I finished downloading successfully, however, I didn't start watching it right away. Now, a day after, I want to watch it, but ATV tells me I have to start the downloading process all over again. WHY? I thought after sucessfully downloading the movie to ATV, it would be available for 30 days in my ATV, without having to download again. To my surprise, it tells me I have to download all over again. It took me 3 hours to download the movie, now I have to repeat the process? Can someone tell me why? Thanks.
Welcome to the Apple Community.
The Apple TV will delete content if it is used to plat something else or is turned off. It only has a limited amount of volatile memory.
If you want to download something for watching at a later time, it would be best doing it from iTunes on your mac/PC and streaming it to the Apple TV when you are ready to watch it. -
I am using an early 2008 MacBook Pro and am having issues with it deleting text on its own (in word, emails, etc.). As I am typing it all of a sudden starts deleting and I can't stop it. This happened once before and it was due to a buldging battery pressing on the track pad. I checked the battery and it appears to be fine. What can I do?
Please read this whole message before doing anything.
This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
Step 1
The purpose of this step is to determine whether the problem is localized to your user account.
Enable guest logins* and log in as Guest. For instructions, launch the System Preferences application, select Help from the menu bar, and enter “Set up guest users” (without the quotes) in the search box. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your personal files or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Step 2
The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode* and log in to the account with the problem. The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode.
Test while in safe mode. Same problem?
After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of steps 1 and 2.
Maybe you are looking for
-
hi guys, im having a problem using FCC in reciever file adapter. in receive an XML like this: header ....details ....details ....details header ....details ....details ....details header taking reference of this blogs i traying to do my conversion /p
-
One of my phones did not get the 2.2 update
I have two Droids and one automatically had the prompt for updating to the 2.2 but the other did not. How do I update that phone?
-
Installing the POSE (Palm Emulator) to work with J2ME WTK 2.2
Hello All- I am trying to install the PalmOS emulator from Palm's website and get it to pop up as a device in the K Toolbar. Although I have not had much luck thus far. I have downloaded the skins, emulator and ROM's from the PalmOS website and have
-
Who has the @#$% record locked!?
I know there are hundreds of other posts asking this (I've read every one I think), but none give the whole answer (unless I haven't found that one yet). I hate to have to add another one, but I can't believe this has not been resolved due to the she
-
Please help me on Business Processes
Hi friends Actually i am new to SRM. i want to know the example of business process for pharmaceutical industry, chemical industry and automobile industry i.e i just want to know what will be the client requirements and how to fullfil the client requ