Little help on Network Settings
Can someone help me understand the real differences between Reset All Settings and Reset Network Settings under Settings > General > Reset? I read the User's Guide but it did not give much detail. Any examples on why I would reset either of the above?
Thanks, I was trying to see if one of these would fix my Yahoo Push problem. I'm not getting my Yahoo mail pushed to my iPhone. I have to manual refresh. But I have two Yahoo accounts on my phone and one is being pushed and the other one is not. I've deleted both accounts, rebooted the phone, and added back the accounts and nothing. Still not pushing on the default account.
Similar Messages
-
Please... a little help with WRT400N settings
I've had been successfully using a WRT400N to extend my wireless network as follows:
The WRT400N connected to my network via an Ethernet port in my kitchen. The cable ran down to a corner of my basement connecting to Verizon router that brings in our Internet, TV etc.
The Verizon router's poor location was a problem, and placing the WRT400N in the kitchen worked perfectly, providing excellent network access and Internet to wireless devices throughout my home. It worked fine for over a year.
Recently, we had a power outage which reset the WRT400N to factory settings. and I am having trouble getting it to work again. I set it up in the first place, but am now having difficulties. Clearly, I am no guru!
I tried to get it going again by: 1) plugging the WRT400N into a PC and giving it a new IP address that would not conflict with the Verizon router (both default to 192.168.1.1) 2) turning off DHCP, 3) renaming the router, 4) changing the router password, 5) setting up a WPA2 security key.
I then plugged the WRT400N back into the kitchen Ethernet port, but something is wrong. Wireless devices cannot find the WRT400N.
The good news is that I can "see" the WRT400N through any PC on the network via a browser and access setup, but the bad news is that devices cannot see or connect to the wireless signal.
When I go to "Status" it shows the IP address, subnet address and default gateway all at 0.0.0.0. On the SETUP page, it has the correct router address (192.168.1.9), and a subnet mask of 255.255.255.0. Not sure if it is supposed to be this way...
Bottom line is that a lot of people seem have this issue and a simple listing of proper settings would be valuable to many people!!
Thanks!RE: 09-06-2011 04:36 PM - last edited on 09-06-2011 04:38 PM
With your setup the modem should be connected to one of the ethernet ports and not on the internet port.
It is. Still not working. -
Resetting network settings, or restoring system HELP!
is there a way to restore your system back to a earlier date such as a PC can? and is there a way to reset network settings besides using system prefrences?? ive tried system prefrences and it doesnt help my problem. someone please help!
Here's a couple of answers from some forums i found.
I realised that I had a modem installed in the networks ports page in preferences. Even though it wasnt ticked I deleted it. Will see what happens when I next connect.
PPP refers to Point-to-Point Protocol, the way you connect to the internet via dialup. OS X's default is to automatically seek a network port to connect via. It sounds like your system is looking for the modem to make a connection before it looks for the Ethernet port.
Try this: Go to System Preferences>Network. Click-pulldown the "Show" pulldown menu that says "Network Status" to reveal and select the item "Network Port Configurations." You should see a list of at least two items: Built-in Ethernet and Internal Modem. The box next to Internal Modem should be UNchecked (and of course, Ethernet box is checked). Also, drag the Internal Modem item to be below Built-in Ethernet. Click the Apply Now button or close System Prefs and agree to Apply the changes in the Close dialog box.
Chuck Reti
VIdeo Editor
Detroit MI
I'm not an expert on OS X yet and someone else may provide a better answer soon but, in the meantime, here's what I'd do:
1) If you have not run the basic maintenance routines do that first. At the least do the fsck -y and Repair Permissions. Then check to see if the problem corrects itself. If you allready have done these or if they didn't help then;
2) search for the .plist file (preferences) related to the PPPoE and move it out of the folder where it resides. Then restart your Mac. if the problem corrects itself delete the moved file.
Hopefully this will help.
MountainMan /Users/ralph/Desktop/Little icons ƒ/icon_biggrin.gif -
My ipod (version 6.1.3) was connectiong to my home wi-fi just fine until I uploaded new music from my itunes via my laptop. Now my ipod and my iphone will not connect to my wireless network. I've uplugged my wireless network and reset my network settings etc... nothing seems to work. Please help!
Does the iOS devices connect to other networks?
Does the iOS devices see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router
- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar
Since both iPhone and iPod stopped connecting I suspect a problem with your network. -
My wi-fi connection is enabled, however Safari is telling me the server stopped responding. My laptop is working fine on the same wi-fe network. I have reset the network settings and still Safari will not open any web pages. Help!
Ralph..........Did as you suggested and I am still getting the message "Safari could not open the page because the server stopped responding". I am not able to connect with anything on the Internet. Frustrating since I am able to connect with my laptop. Thanks for the suggestion.
-
The wi-fi in my iphone 4S is 'greyed out' and i am not able to switch it on. I have tried resetting the network settings but nothing happened. I can't even download the new iOS7 version as it requires WI-FI to do so. Please help.
I had same problem. I removed the back cover, and warmed wi-fi module by hairdryer of my wife). five days wi-fi works great. I do not know what will happen next.
during operation iphone must be turned off. time of heating is near five minutes. wifi module is located upper the battery, on the upper right corner of device. -
After my iphone4S update to 7.0.6, it have a problem that keep searching network then no service show on display. Can't call. I have try check sim card, reset network settings, and restore my iphone. Still not working at all. Need help please.Urgent.TQ
Izit software or hardware? Confuse:(
Only can use wifi now.
Any way thanks guys for ur suggestion:) amishcake and simes -
My iPad wifi was working great until I I connected it by Bluetooth to a keyboard (zagg). It was the first time I'd used Bluetooth
Immediately Internet was dropped on my ipad. My iPhone was and is still connected no prob. And I cannot get the iPad wifi to work again....at all!!!
This is major as I am away from my desktop for three months. Any fix cannot involve being at my desktop with iTunes which is 10,000 km away
So far This is what I've tried based on other discussions-
-turned Bluetooth off and unpaired to keyboard which was also turned off
- turned iPad wifi off and on (several times)
- forgot the network I useArrive Jul 19 depart Aug 25th. Originally it was Sept 9.
-- reset network settings
What happens is that the iPad sees the network and I enter my password. But, instead of getting "check mark" indicating a successful connections it keeps "circling". Sometimes the airport bars will show, but disappear or flicker. It never connects with a check noted in settings. Any attempts to use internet confirm there is no connection
My network is not a cafe or public network. It is one I regularly use here at my family's home where I am visiting
Any ideas!Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130?tstart=60
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
Everytime I try to access the itTunes Store, this is the message I receive:
iTunes could not connect to the iTunes Store. The network connection timed out.
Make sure your network settings are correct and your network connection is active, then try again.
The internet connection is fine. I don't know how to fix this problem, and in the meantime I cannot connect at all to buy songs. Thanks for your help.I feel you pain i'm haveing the same problems here.
iTunes could not connect to the iTunes Store. The
network connection timed out.
Make sure your network settings are correct and your network
connection is active, then try again.
does anyone plz have some insight for us. -
My ipod 4 when i plug it to my pc Windows 7 had worked fine for 8 months then one day i plug it in and a message came USB device not recognized, i tried reset network settings and nothing i did not install any software before this happend i called apple they did not know, any help out there TX
Start here:
iPhone, iPad, or iPod touch: Device not recognized in iTunes for Windows -
I recently when to England. When I returned to the US, my iPhone 5 wouldn't find the 4G network. I've tried restoring network settings, I've tried hard resets. I finally wiped the phone, and now, it won't let me restore anything. I'm kind of stuck - this is both my personal and my work phone, so I'm really in a bother here. Help!
I had "do not disturb" on in England. I did take it off airplane mode periodically, but I never actually used the network. I stuck to local wifi to do brousing and a bit of messaging. It periodically told me I was on an English network, but I didn't actually use it. And I had data roaming shut off all together.
when I try to restore, I get this message:
Your iPhone could not be activated because the activation server is temporarily unavailable. Try connecting your iPhone to iTunes to activate it, or try again in a couple of minutes. If this problem persists, contact Apple Support at apple.com/support.
When I try it through iTunes, I get a similar message.
and the network just keeps saying, "Searching..." -
Apps tab of Creative Cloud desktop helper constantly displays "Download error. press retry or contact customer support". As well as reloading, I've also quit CC desktop helper, restarted computer, checked network settings, relogged in. Cannot download any new apps or updates. please help.
System: Mac OSX 10.9.4. 3.4ghz intel core i7, 8gb ramHello,
Adobe has brought these new links in this matter:
Troubleshoot Creative Cloud download and install issues and
App doesn’t open; progress wheel spins continually
Please have a look there. If necessary and for further questions click through http://helpx.adobe.com/contact.html and if "open" please use chat, I had the best experiences. I quote from Preran: The chat button is activated as soon as there is an agent available to help.
Good luck!
Hans-Günter -
Need to update my IPhone 4 and connected to the itunes on windows XP. I clicked on update and waited. A message appears that says," Cannot update etc. Please check your network settings/config., etc... or try again later" and it's been happening for a while. Please help.
Close your iTunes,
Go to command Prompt -
(Win 7/Vista) - START/ALL PROGRAMS/ACCESSORIES, right mouse click "Command Prompt", choose "Run as Administrator".
(Win XP SP2 & above) - START/ALL PROGRAMS/ACCESSORIES/Command Prompt
In the "Command Prompt" screen, type in
netsh winsock reset
Hit "ENTER" key
Restart your computer.
If you do get a prompt after restart windows to remap LSP, just click NO.
Now launch your iTunes and see if it is working now.
If you are still having these type of problems after trying the winsock reset, refer to this article to identify which software in your system is inserting LSP:
iTunes 10.5 for Windows: May see performance issues and blank iTunes Store
http://support.apple.com/kb/TS4123?viewlocale=en_US -
I have iPhone 6, 8.3. I cannot use bluetooth at all from my device, even to connect my macbook pro. I did all the recommended trouble shooting such as reboot and reset network settings. but it does not recognise any bluetooth device. Pls help.Thank you.
See iPhone BT profile on what can be connected/paired:
iOS: Supported Bluetooth profiles - Apple Support
And BT troubleshooting:
iOS: Troubleshooting Bluetooth connections - Apple Support -
Hi. I am having problems connecting to the wifi at my caravan site. My iPad recognises the connection but when I put the password in correctly it says it cannot connect. I have reset my network settings in general but it has made no difference . Any ideas?
Some may not be applicable.
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom
Maybe you are looking for
-
Issue with Active Directory User Target Recon
Hi , I am facing an issue with Active Directory User Target Recon My environment is OIM 11g R2 with BP03 patch applied AD Connector is activedirectory-11.1.1.5 with bundle patch 14190610 applied In my Target there are around 28000 users out of which
-
Query works everywhere but Flex: inline views not supported perhaps?
EDIT2: Actually not. It turns out to be a bug in the way Adobe is treating any integer PK column, no matter how it is defined, INT, or INTEGER, as an alias for the rowid in SQlite. This is incorrect. rowid does not always equal the PK value. This c
-
How can i identify the environment name or database name in the PL/SQL code
Hi, I am using UTL_FILE to genearate the files., My problem is, I have to design the common sql file , which can be executed in 2 diffrent environments ( Say QA & DEV ) , with no parameters. It has to identify the environment and based on the environ
-
Hi I am using DBMS_METADATA to dump the ddl of database objects into a variables using JDBC. I need to seperate each block so that there is a delimiter/marker after every column, constraint, indexe etc inside ddl. Looking for some sugesstions on how
-
I am getting error message: Unexpected error opening catalog. What should I do
Lightroom started acting slightly strange, not displaying certain images in the folder I was working on, for example. I shut it down, but when I tried to start it again, it would not open using my normal catalog, and I had the message, "Unexpected e