Live Update cant access the MSI Server

Hi,
I am trying to update my BIOS to v.1.4, but when come to "connect to MSI Live Update Server" then it hangs and I cant come any further.
I reinstalled the MSI live Update but the prob. remains.
Can anyone help with this problem ?
Thanks

Similar Messages

Asa 5505, the outside cant access to a server in the inside

hi, i have an Asa 5505, a pc in the outside with the ip 10.1.1.6 cant access to a server in the inside 192.168.1.4, pls help...
this is my conf:
ASA Version 8.0(4)
hostname ciscoasa
domain-name default.domain.invalid
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 0
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 10.1.1.2 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa804-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
access-list 100 extended permit tcp any host 10.1.1.3 eq www
pager lines 24
logging enable
logging asdm debugging
mtu inside 1500
<--- More --->
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-613.bin
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) 10.1.1.3 192.168.1.4 netmask 255.255.255.255
access-group 100 in interface outside
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
<--- More --->
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 192.168.1.2-192.168.1.254 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
<--- More --->
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:14e7b74fabc386613ae646b915f60e9e
: end
ciscoasa#

Andres
The security level for your inside interface should be 100 ie.
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
After changing that can you
1) ping the outside interface of the ASA from the pc or ping the PC from the ASA
2) I'm assuming you are trying to connect to 10.1.1.3 when you attempt the connection ?
Jon

I cant access the root share of a windows server after upgrading to mountain lion

Hi Guys,
Since upgrading to mountain lion i cant access the shared drives on our windows server. For example in a windows machine if i go to run the type \\server\ i get all the visible shares available. in my previous version i was able to do the same (obviously i would authenticate with my AD account). now when i try to access those same shares i get the message below:
"The operation cant be completed becuase the original item for "/" cant be found"
I can however connect to the shares directly for example if i connect to server path \\server\data it works ok.
I have verified my account details and they are ok - i have also disconnected and reconnected the connection.
This was working fine before the upgrade. can anyone help??

well iv just managed to get to 35 gig free (just deleting iphone backups) and im now able to get past the next screen on bootcamp.
unfortunatly its only allowing me to create a new partition not delete the current.
this is leading me to think the old ones master partition has become damaged and the hard drive dosent know it exists any more.
if this is the case (please tell me im wrong though) what options do i have as i dont want to / have the money to buy another hard drive to back everything up to it with.
thanks again
gareth

HT201210 update my ipad 3 wifi+cellular to ios7 but cant access the home screen

update my ipad 3 wifi+cellular to ios7 but cant access the home screen

iOS 7 is BETA software.
As such, it cannot be discussed here.
If you are a developer, seek assistance in the developers forums.
If you are not a developer, you have no right to the software on the device and no right to support. Look elsewhere.

Bios trouble .. cant access the setup P-45 neo-f(outside box) / ms-7519(sandra)

P-45 neo-f(outside box) / ms-7519(sandra)
BIOS : 64-0100-009999-00101111-081208-Eaglelake
version: 1.0
when i press [DEL] to enter the bios setup .. i get a blank screen .. and nothing more happends.
and sometimes the screen tells me "No signal input"
.. I have never been able to on this computer.
I never tried to update or flash the bios .
It would be a very slow process to get it fixed by the reseller ..probably a few month..
Maybe anyone here knows whats wrong?
and what i can do to fix it
The computer boots and operates normally .. but i want to disable the built in soundcard, to replace it with a better one.
I also want to replace the cpu with something faster.. its a 2.33ghz quadcore now .(whats the fastest cpu for this mainboard ? where can i find a list)
If i flash or reset the bios? will it autodetect the hardware, even if i still cant access the setup screen? or just make things worse
.. now it works .. its a miracle .. i figured out u u have to press del at the exact right moment at boot .. if u press it too soon .. = black screen .. too late = no signal input .. wierd design
but i still dont find this board at the msi site .. only p45 neo .. without F .. and i cant use the live update becuse of 64bit os

Quote
only p45 neo .. without F
P45 Neo-F and P45 Neo are identical.
Quote
whats the fastest cpu for this mainboard ? where can i find a list)
On the MSI Product Site for your Board:
http://global.msi.eu/index.php?func=prodcpu2&prod_no=1482&maincat_no=1&orderby=cpu_speed%20ASC#menu
Quote
its a 2.33ghz quadcore now
Must be a Q8200 then. But which one exactly? There are three different revisions. In any case, if your really have BIOS v1.0, you need a BIOS Update to ensure proper CPU Support.
Quote
P-45 neo-f(outside box) / ms-7519(sandra)
BIOS : 64-0100-009999-00101111-081208-Eaglelake
version: 1.0
Do not trust Sandra for board and BIOS Information. Please check your current BIOS Version in the BIOS Setup under Standard CMOS Features -> System Information.
Before posting another reply here, please read this:
>>Posting Guide<<

Can T3Client access the WebLogic Server Workspace.

Hi,
a couple of questions ....
Can the T3Client access the Weblogic Server Workspace ???
If so,how ???
The reason for this that I want to get access to the Weblogic Server Cache.
Is there any other way of getting access to the WebLogic Server Cache ???
Kindly let me know if you find the answer.
Thanks & regards,
Karan.

Hi there,
I would recommend taking a look at the troubleshooting steps found in the article below.
iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
http://support.apple.com/kb/ts1814
-Griff W.

I cant access the istore on version 10.5.x. How do I get this going??

I've upgraded my itunes to version 10.5.x and now I cant access the istore.
How do i get this resolved??

Choose About this Mac from the Apple menu and check the processor.
If it's a G4 or G5, buy a retail Mac OS X 10.5 DVD from a source such as Amazon or eBay; Apple still might have copies in stock if you phone them.
If it's an Intel Mac, buy a Mac OS X 10.6 DVD from the online Apple Store, install it, and run Software Update. If your Mac is compatible, you can then upgrade to 10.7 or 10.8; Mac OS X 10.7 requires a Core 2 Duo or better CPU.
(80984)

Since downloading itunes 10.5 i cant access the itunes store. how do i fix this?

Since i dowloaded itunes 10.5 i cant access the itunes store.It justs freezes halfway. Can anyone help me?

My issue was a conflict with Xeno Pro network card. Had to update to beta level drivers for 64bit Windows 7 to resolve.

5800 applications cant access the net..

in my 5800, opera mini is working fine, but no other application cant access the internet..looking forward for a solution.
Solved!
Go to Solution.

Hi turtlebuster,
Welcome to Nokia Support Discussions!
Can you further elaborate on your concern? Which internet connection are you using? Have you tried using a WLAN connection to access the internet? Is there any error message? Can you access the internet using the phone browser? Can you name some of the applications you have on the phone?
We can try some basic troubleshooting steps to isolate the issue:
1. Clear your phone browser's cache. Refer to the manual for the instructions: http://nds1.nokia.com/phones/files/guides/Nokia_5800_XpressMusic_UG_en.pdf
2. Under settings, check your default access point. Make sure that you are using this access point for the other applications you are using.
3. In your phone browser, you can set the access point to "Always ask". This will enable you to choose which connection to use when using the phone browser:
Internet> three lines> Settings> General> Access Point> Always Ask.
If the above steps did not work, you can follow these steps:
1. Perform a power cycle on the phone. Turn off the phone and remove the battery for a few seconds. Place the battery back and turn on the phone.
2. You can factory reset the phone. This will not delete any personal data but it will restore the phone's default settings.
Settings>Phone>Phone mgmt>Factory settings
The default code is 12345 unless otherwise changed. After the factory reset, you can customize your settings on the phone. For internet settings, you can check with the operator.
3. Check for updates using the Nokia Suite. If none, you can try to reinstall the phone software. For video tutorials, check www.nokia.com/nokiasuite
4. If there is no progress, you can reformat the phone. This will wipe all data, thus make sure to have a backup file first to prevent data loss. You can create a backup file through Nokia Suite. To format the phone, dial *#7370# on the dialer.
Hope this helps.

Configure Synchronization Connections An error has occurred while accessing the SQL Server database

Hi,
i am getting following error message
Central Administration --> Synchronization Connections
An error has occurred while accessing the SQL Server database or the SharePoint Server Search service.
If this is the first time you have seen this message, try again later. If this problem persists, contact your administrator.
Central Administration --> Manage Profile Service: User Profile Service Application --> Manage User Properties
Error
An unexpected error has occurred.
Troubleshoot issues with Microsoft SharePoint Foundation.
Correlation ID: 3bce5a11-f2dc-4788
Please tell how to fix it.
iffi

Event ID 5555 -> i have change the Timer jobs recycling time AM to PM
for User profile page not display number of count in the page first check services , connection ,
IISRESET /NOFORCE / timer services restart
Deepesh Yevle MCTS

Server 2012 R2 SMB - The process cannot access the file '\\server\share\test.txt' because it is being used by another process.

Hi,
We are having issues with Server 2012 R2 SMB shares.
We try to write some changes to a file, but we first create a temporary backup in case the write fails. After the backup is created we write the changes to the file and then we get an error:
The process cannot access the file '\\server\share\test.txt' because it is being used by another process.
It looks like the backup process keeps the original file in use.
The problem doesn't always occur the first time, but almost everytime after 2 or 3 changes. I have provided some code below to reproduce the problem, you can run this in a loop to reproduce.
The problem is that once the error arises, the file remains 'in use' for a while, so you cannot retry but have to wait at least several minutes.
I've already used Process Explorer to analyze, but there are no open file handles.
To reproduce the problem: create two Server 2012 R2 machines and run the below code from one server accessing an SMB share on the other server.
Below is the code I use for testing, if you reproduce the scenario, I'm sure you get the same error.
We are not looking for an alternative way to solve this, but wonder if this is a bug that needs to be reported?
Anybody seen this behavior before or know what's causing it?
The code:
string file =
@"\\server\share\test.txt";
if (File.Exists(file))
File.Copy(file, file +
".bak", true);
File.WriteAllText(file,
"Testje",
Encoding.UTF8);
The error:
System.IO.IOException: The process cannot access the file '\\server\share\test.txt' because it is being used by another process.

Hi,
There is someone else having the same issue with yours. You could try code in the article below:
“The process cannot access the file because it is being used by another process”
http://blogs.msdn.com/b/shawncao/archive/2010/06/04/the-process-cannot-access-the-file-because-it-is-being-used-by-another-process.aspx
If you wonder the root cause of the issue, the .NET Framework Class Libraries forum can help.
Best Regards,
Mandy
If you have any feedback on our support, please click
here .
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Error while accessing the application server file

Hello,
When I try to load the data from CSV file to PSA , I am getting following error message
"Error while accessing the application server file"
"Errors in source system"
I gave the right file path
I am not sure about this error message.
Thanks,

Hi ram,
if you have more than one application server running in your BI system (see at transaction SM51) be aware that your infopackage will be executed on the right one. Each application server has its own file system and your job need to run on the server your file is stored on.
Also check if the os user of the SAP system itself (<sid>adm on Unix) has rights to read that file.
Bye
Frank

My itunes library was on my PC. About two years ago I switched it to my Seagate server/hardrive. (itunes-preferences-advanced-change library). Last summer (2012) I bought a macbook, which seems to access the seagate server hard drive fine for word docs,

My itunes library was on my PC. About two years ago I switched it to my Seagate server/hardrive. (itunes-preferences-advanced-change library). Last summer (2012) I bought a macbook, which seems to access the seagate server hard drive fine for word docs, excel spreadsheets,etc. It also seems to have started its own library which is not complete. My PC died this summer (I still have it though).
Now when syncing any of the multiple devices (ipods,ipads, iphones) that we have with my mac book, itunes states that "an error occurred" or the "app cannot be found". Itunes wants me to erase the device and sync with my macbook. The message "The iPhone “Renee’s iPhone” is synced with another iTunes library on “Renee PC”. Do you want to erase this iPhone and sync with this iTunes library? An iPhone can be synced with only one iTunes library at a time. Erasing and syncing replaces the contents of this iPhone with the contents of this iTunes library."appears.
Any assistance would be greatly appreciated.
Renee

u can give try to using external enclosre and backup ur files. I hope u will get files back. or using external enclosre with ur hdd boot into Linux and try to mount ur harddisk.
there are multiple no of tutorial to mount apple partion in Linux.

A fatal error when attempting to access the SSL server credential private key. Error code 0x8009030d. Windows 8.1.

Hi,
We develop a server-side application which receives incoming https connections using self-signed certificate. It was all ok while we were using Windows 7 or Windows 2008 as OS, but when our clients started installing Windows 8 as server OS they encountered
big problem: application got unavailable in few hours after start.
In event logs we have following:
A fatal error occurred when attempting to access the SSL server credential private key. The error code returned from the cryptographic module is 0x8009030d. The internal error state is 10001.
After restart, application recreates certificate and all works normal few hours till next fatal error.
This
article did not help us. And I repeat that this error appears only on Windows 8 (we tested on Windows 8.1). Windows 2012 Server we did not test yet.
How we can solve this problem?
Best regards.

Hi,
Since this article released in 2008,I suspect the code mentioned in this article doesn't supprot Windows 8.
And since the certificate was written by C#,I suggest you submit a new case on MSDN Forum as they will be more professional on your issue:
https://social.msdn.microsoft.com/Forums/en-US/home
Regards,
Kelvin hsu
TechNet Community Support

Error in Accessing the Report Server URL

Hi All,
I am trying to access the Report Server URL in PowerPivot.But facing below issue .Can any one help me how can I solve the issue
Thanks,
Sid

Hi Visakh,
Yes,The user is holding the permission as "Global User" in sql.Hope you help me in solve this issue
Thanks, Quality Communication Provides Quality Work. http://siddiq-sharepoint2010.blogspot.in/ Siddiqali Mohammad .
Hi siddiqali,
According to the screenshot you posted above, the use account didn't have sufficient permission to open the report, please check the following prerequisites before you perform the action:
You must use a report definition (.rdl) file as a data source. Importing from a report model is not supported.
You must have permission to open the report under your Windows user account, and you must know the address of the report or the report server that hosts it. You can check your permissions by trying to open the report in a Web browser first.
If the report opens, it confirms that you have sufficient permissions and the correct URL.
Reporting Services must be version SQL Server 2008 R2 or SQL Server 2012. Those versions include the data feed export feature that streams report data in the XML data feed format. You can identify the report server by the Export as Data Feed option
that appears in the report toolbar when you open the report in browser:
For detail information, please see:
Import Data from a Reporting Services Report:
http://technet.microsoft.com/en-us/library/gg413491.aspx
Regards,
Elvis Long
TechNet Community Support

Live Update cant access the MSI Server

Similar Messages

Maybe you are looking for