LMS 3.1 and CiscoView 6.1.8 not swhowing 10Gb modules

Hi!.
We´ve got a CiscoWorks (LMS 3.1) with CV 6.1.8 and it doesn´t display the new installed 10Gb (X2-10Gb-SR=) modules in the Catlyst 6509E chassis and Catalyst 3750E, what can I do to fix it?
Thanks.

Hi ,
Upgarde the LMS to LMS 3.2 and then check the issue..
Download link for LMS 3.2:
https://cisco.mediuscorp.com/market/networkers/productView.se.work?/nxt/rcrs/proieidentity/=17651
Note : you do not need a new liense for LMS 3.2 , your existing license will just work fine
Thanks
Afroj

Similar Messages

LMS 4.0 and EoS/EoL Hardware report not working..

Hi guys,
our LMS server has proxy access to the internet but running a EoS/EoL hardware report results in:-
No data available in the report. The problem could be any one of the following:
1. No EoS/EoL hardware data available in the LMS database for the selected device(s).
2. PSIRT/EOX system job might not have run, or might have failed.
3. You might have entered the wrong cisco.com credentials.
I tried doing it manually by downloading the psirt_eox_offline.txt to the relevant directory and changing the EoS/ EoL configuration to 'local server' on our LMS server but I still get the above message.
I know for a fact we are running devices that have recently been announced by cisco as going EoL and or EoS eg 3750 switches and 2800 series routers so I was expecting to see something in the report.
How can I get this working successfully?
Thanks in advance
Trevor

Problem is now fixed.
I disabled 'use proxy server' and its now working.

LMS 3.2 and RME 4.3.1 telnet with tacacs+ fails

Hi everyone,
I'm having issue with credentials verification for telnet with TACACS+ enabled. Verification job fails with "Telnet: Incorrect" and an exception to daemons.log:
om.cisco.nm.lib.cmdsvc.CmdSvcException: com.cisco.nm.lib.cmdsvc.telnet.TelnetException: Unable to read from socket
        at com.cisco.nm.lib.cmdsvc.TelnetSession.connect(TelnetSession.java:89)
        at com.cisco.nm.lib.cmdsvc.Session.connect(Session.java:152)
        at com.cisco.nm.lib.cmdsvc.AuthHandler.connect(AuthHandler.java:254)
        at com.cisco.nm.lib.cmdsvc.OpConnect.invoke(OpConnect.java:56)
        at com.cisco.nm.lib.cmdsvc.SessionContext.invoke(SessionContext.java:299)
        at com.cisco.nm.lib.cmdsvc.Engine.process(Engine.java:57)
        at com.cisco.nm.lib.cmdsvc.LocalProxy.process(LocalProxy.java:22)
        at com.cisco.nm.lib.cmdsvc.CmdSvc.connect(CmdSvc.java:190)
        at com.cisco.nm.lib.cmdsvc.CmdSvc.connect(CmdSvc.java:166)
        at com.cisco.nm.xms.xdi.pkgs.LibDcma.persistor.CliOperator.<init>(CliOperator.java:214)
        at com.cisco.nm.xms.xdi.pkgs.SharedDcmaIOS.transport.IOSCliOperator.<init>(IOSCliOperator.java:116)
        at com.cisco.nm.xms.xdi.pkgs.SharedDcmaIOS.transport.CatIOSSwitchCliOperator.<init>(CatIOSSwitchCliOperator.java:56)
        at com.cisco.nm.xms.xdi.pkgs.SharedDcmaIOS.transport.Cat6kIOSCliOperator.<init>(Cat6kIOSCliOperator.java:32)
        at com.cisco.nm.xms.xdi.pkgs.SharedDcmaIOS.transport.Cat6kIOSConfigOperator.getOperator(Cat6kIOSConfigOperator.java:35)
        at com.cisco.nm.xms.xdi.pkgs.LibDcma.persistor.OperatorCacheManager.getOperatorForDevice(OperatorCacheManager.java:50)
        at com.cisco.nm.xms.xdi.pkgs.LibDcma.persistor.ConfigOperation.doConfigOperation(ConfigOperation.java:99)
        at com.cisco.nm.xms.xdi.pkgs.SharedDcmaIOS.transport.IOSConfigOperator.fetchConfig(IOSConfigOperator.java:73)
        at com.cisco.nm.rmeng.dcma.configmanager.ConfigManager.updateArchiveForDevice(ConfigManager.java:658)
        at com.cisco.nm.rmeng.dcma.configmanager.ConfigManager.performCollection(ConfigManager.java:1646)
        at com.cisco.nm.rmeng.dcma.configmanager.CfgUpdateThread.run(CfgUpdateThread.java:27)
I've tried to edit TacacsPrompts.ini also with suggestion to enter "," after last space character
I'm using only TACACS so all prompts are the same. I'm using MOTD also.
TACACS prompt looks like this example : "TEST username: ,TEST password: " so this looks obvious.
The issue started to appear after some patching done to RME and CiscoView, but I'm not sure that this is connected anyhow.
Thanks for all the help

Hi!
They gave me the solution like this:
line vty
timeout login response 90
Ofcourse it helped but this it still inproper behavior from LMS side. It sends the username char by char for more than a minute! Guess the scenario with thousands of devices.... It will take ages to telnet to them. And network performance has nothing to do with that - i'm running the LMS on a powerful Sun and the network is mostly gigabit connected.
Setting timeout login response is a workaround but does not fix the problem.
Still waiting fot some fix to LMS not for fairly acceptable workarounds.
This is NOT case with TACACS enabled on a router. The box responds within moment when telneted using commandline or other NMS software. This is a problem with LMS telnet login mechanism and prompt parsing (TacacsPrompts.ini doesn't seem to work at all, I could type there anything and it has no effect on the login proces).
Besides this SSH to the same box wit TACACS works flawlessly. But then it parses only password prompt not the username - this is sent by ssh.

LMS 3.2 and MS SCOM and SCCM

Is there any recommendation regarding installation of CW LMS 3.2 and MS SCOM and SCCM on the same server?

This was not tested internally, so I cannot say whether or not there are any conflicts or problems. If possible, consider virtualizing LMS on one VM with the MS managers on another VM. Provided resources on the hardware are sufficient, this would be the safest course if all suites need to be on the same physical server.

Lms 3.2 and window server 2008 r2 standard

we have bought lms 3.2 and window server 2008 r2 standard. Now we know, it cant be used togetther
Could we upgrade to lms 4.0.1 ? If so, how can we do ?
thank you.
Duyen.

Correct, LMS 3.2 is not supported on Windows 2008 R2. You can upgrade to LMS 4.0 (which is supported on R2), but that is not a free upgrade from LMS 3.x. You can, however, download a free 90-day eval of LMS 4.0 from http://www.cisco.com/go/nmsevals .
It sounds like you need to contact your reseller or account manager to see what they can do. If you just purchased LMS 3.2, you may be able to get a free or discounted upgrade to 4.0.

Lms 3.2 and window server 2008 standard: License Server/Daemon Manager is down

LMS 3.2 and window server 2008 standard, get error when we try
Khi truy nhập vào menu chức năng:
License Server/Daemon Manager is down. Please check license.log for more information.
access licensing:
Error communicating with License Server. License Server may be down. Please start the License Server, then refresh the page.
Lincense.txt is file log of LMS
Must I have to active window server 2008 first ?
thank you very much ?

Hi ,
--Add the Casuser to the Administrator Group
and then reset the casuser password:
1. Go to CSCOpx\setup\support> and run the following command:
resetCasuser.exe
2. Restart the daemon manager:
Net stop crmdmgtd
Net start crmdmgtd
Let me know how it works
If above did not help then send me the syslog.log and screen shot of the EventViewer with the latest Application Error that you see there.
--also screen shot of the below directory :
NMSROOT\etc\license
Thanks
Afroj

LMS 3.2 and QPM 4.1.2

Hi Forum,
my customer play to deploy LMS 3.2 and last QPM 4.1.2 on the same server.
In the documentation of QPM only Common Services 3.2 are mentioned. Does this match with LMS 3.2 - since LMS utilizes CS 3.3?
Does anybody know something about that?
Thanks a lot in advance.
Frank

No, you cannot install these two on the same server. Doing so will break both products. You must dedicate a server to each since they require different versions of Common Services.

LMS 2.1 and nGenius Real-Time Monitor 1.4

Dear NetPros,
Is the LMS 2.1 and the nGenius Real-Time Monitor 1.4 can be installed on the same system?
Regards,
Steve

Yes, but not recommended. Keeping them on separate servers will be more beneficial.

LMS 4.0 and Prime Infrastructure..!

Hi,
I am using LMS 4.0 and as the licenses got expired I came to know that I need to buy Prime Infrastructure license as LMS 4.0 reached End of life.
So now if I buy the prime infrastructure licenses, will it work on LMS 4.0 or I need to upgrade? and how can I get the upgrade?
Thanks..!

You would need to upgrade. Prime Infrastructure 1.2 has LMS and WAN buildt in.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Configuring rcp on ciscoworks LMS 2.5 and cisco 3560 switch

Dear All,
i am having LMS 2.5 and nearly 50 cisco 3560 in my network. And I want to configure rcp. How can I do it. Kindly help
regards,
RAHIL KHAN

Have a look at this link for the server:
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_resource_manager_essentials/4.0/user/guide/swmgt.html#wp1328314
For the device you'll need something like:
username cwuser password 7 000C1C0A05
ip rcmd rcp-enable
ip rcmd remote-host cwuser 172.17.246.221 cwuser enable
ip rcmd remote-username cwuser

LMS 3.2 with RME 4.3.1 not Archiving configuration

HI ,
I am facing problem in Ciscoworks in Fetching config Archieve from Cisco ASA-5510 Adaptive Security Appliance . I am using LMS 3.2 and RME 4.3.1
SSH is enable in the device, and from LMS server I am able to connect through Putty. Also from Management station to Device it showing SSH is up for both version. But from RME its failing Its giving below mentioned error
Device: COGINHYDGCBDFHRTF1       Status:   Failed
*** Device Details for COGINHYDGCBDFHRTF1 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> SSH,Telnet,TFTP,RCP,SCP,HTTPS
Execution Result:
RUNNING
CM0151 PRIMARY RUNNING Config fetch failed for COGINHYDGCBDFHRTF1 Cause: Couldnot enter ENABLE Mode from USER Mode on 10.241.44.220.TELNET: Failed to establish TELNET connection to 10.241.44.220 - Cause: Connection refused.
Action: Check if protocol is supported by device and required device package is installed. Check device credentials. Increase timeout value, if required.
I have tried from LMS server by telneting to port 22, its giving below output------SSH-1.99-Cisco-1.25
When I have tried to test device credentials for SSH and SSH Enable mode, then below output I am getting. SSH remains blank status.
Device Name
SSH
Enable
by SSH
1.
COGINHYDGCBDFHRTF1
Did Not Try
Pls help to resolve this.

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
],DEBUG,[Thread-778],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Returning from Session.send('terminal width 0
[ Thu Oct 28 15:02:28 GMT+05:30 2010 ],DEBUG,[Thread-778],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,in trimPrompt(), prompt == 'ASA-F1# '
[ Thu Oct 28 15:02:28 GMT+05:30 2010 ],DEBUG,[Thread-778],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,printStackTrace,51,stacktracecom.cisco.nm.lib.cmdsvc.CmdSvcException: Unhandled SSHv2 message: SSH_MSG_CHANNEL_REQUEST(98)
                Channel ID: UInt32[ 0 ]
                Channel Request Type: exit-status
                Want Reply: true
                Timeout (msec): 0
                Exit Status: UInt32[ 0 ]
What i deduce from this output is may be "ter width 0" is un-authorised for the user or is not supported by the particular code that you are currently running in the box.
Best Regards // Rajiv

LMS 3.2 DFM error "URN_NOT_FOUND : urn "ogs_server_urn" : Not found !!"

Hi Joseph,
one of our client is using lms 3.2 and getting the following error in DFM -> device import -> Auto Allocation mode configuration.
Error in getting instance of TreeGenerator class
com.cisco.nm.trx.kdm.utils.DcrGroupSelectorTreeGenerator
Root Cause:com.cisco.nm.xms.ctm.common.CTMException: URN_NOT_FOUND : urn "ogs_server_urn" : Not found !!
I have gone through all documents available in netpro and done all tests mentioned for trouble shooting
following is the result of command " pearl resolver.pl "
D:\CSCOpx\bin>perl resolver.pl hyd-wbpo-cwks.wipro.com
Original name: hyd-wbpo-cwks.wipro.com
Hostnames/IP Addresses:
hyd-wbpo-cwks.wipro.com/10.120.232.143
Here with I have attched the dfmserver.log, dfmserver1.log, dfmOGSserver.log , netstat -a -n -o -b, and output of PDshow.
One thing I observed when I am running the command "brcontrol" under "D:\CSCOpx\objects\smarts\bin>" it is not returning me any output.
All the devices in dfm are stacked in learning state at 10%. The SNMP RO string used in DCR is alos ok.
Regards,
Satya

Hi any idea from anyone?

Hi Guys, I am using the full width video widget on a site. The widget was working perfectly however I have just added additional content to the site and re-uploaded and now the video is not working! Please help I have tried everything and am freaking out

Hi Guys,
I am using the full width video widget on a site. The widget was working perfectly however I have just added additional content to the site and re-uploaded and now the video is not working! Please help I have tried everything and am freaking out as this web-site has been payed for by my client.
Alex

Many thanks.
With those symptoms, I'd try the following document:
Apple software on Windows: May see performance issues and blank iTunes Store
(If there's a SpeedBit LSP showing up in Autoruns, it's usually best to just uninstall your SpeedBit Video Accelerator.)

HT1296 I already have an itunes account on my laptop but have been setup on a mac and have songs that have not been purchased from the itunes store, I cannot get the songs from my iPhone onto my itunes account on the mac. how can I do this?

I already have an itunes account on my laptop but have been setup on a mac and have songs that have not been purchased from the itunes store, I cannot get the songs from my iPhone onto my itunes account on the mac. how can I do this?

You copy them from your old computer or your backup copy of your old computer.
The iphone is not a backup/storage device.

OSX 10.10 and HP Officejet Pro 8500A not working

I updated my operating system to Yosemite OSX 10.10 and now my printer will not print or scan. When the click on the HP Utility it can not find the printer. I looked in Finder but folder for HP is gone. I went on HP's website but there are not drivers for version 10.10. I tried to download a driver for previous version of OS X but it says not compatible.
How do I get my printer back up on-line?
Thanks for your help.

The HP Printer Drivers v3.0 for OS X should help, or Software Update.
It's shown as supported here: OS X: Printer and scanner software available for download

LMS 3.1 and CiscoView 6.1.8 not swhowing 10Gb modules

Similar Messages

Maybe you are looking for