LMS 3.2.1 netconfig error

Hi,
I am using LMS 3.2.1, and while deploying the configuration to the device via Netconfig job, I receive below error message. All commands deploy successfully but Netconfig job status always failed because of below error message;
Command(s) failed on the device TFTP: Failed on the device.
However I can sync archive the same devices successfully.
Transport Settings->Archive management = SSH TELNET TFTTP RCP
Transport Settings->Config Deployment = SSH TELNET TFTTP
Please advise how to rectify the issue.
Thanks

Hi Rizwan,
You are using system defiend templates to push the Netconfig job or you are using the ADHOC option ?
If you are using system defiend templates use the ADHOC job and see if it makes any difference.
I remember there were few bug on this issue ,I found one :
CSCeh40578 netconfig reports success on failure
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Similar Messages

LMS 3.2.1 Backup error

Hi
We have recently installed a new version of LMS 3.2, and everything is working fine.
but till now the backup process hasn't started correctly to a directory on our drive D, and once I start a backup process, I recieved the following error
ERROR (1261): FATAL error: Database engine 'opsxmleng' could not be started on database 'opsxml' in Bulk mode.. Backup failed.
Has anyone seen this issue before ?
appreciate your advice.

hi michel,
thanks for document, I used the following command to initialize the database :
C:\Program Files (x86)\CSCOpx\bin>perl dbRestoreOrig.pl dsn=opsxml dmprefix=Opsxml
and I got the following result, there is an Error
WARNING: Existing contents of opsxml database will be lost.
Do you want to continue [y/n]?y
INFO: Starting the DataBase
Starting database engine opsxmlEng
INFO: Process created
INFO: Started the Database engine : opsxmlEng Retry 0
INFO: Started the Database engine : opsxmlEng Retry 1
INFO: Started the Database engine : opsxmlEng Retry 2
INFO: Started the Database engine : opsxmlEng Retry 3
INFO: Started the Database engine : opsxmlEng Retry 4
INFO: Started the Database engine : opsxmlEng Retry 5
INFO: Started the Database engine : opsxmlEng Retry 6
INFO: Started the Database engine : opsxmlEng Retry 7
INFO: Started the Database engine : opsxmlEng Retry 8
INFO: Started the Database engine : opsxmlEng Retry 9
INFO: Getting message
INFO: Connect the database dsn=opsxml
ERROR: Failed to authenticate [opsxml] database.
Database engine 'opsxmlEng' could not be started on database 'opsxml' in Bulk mo
de.INFO: Calling OpsConfUpdate executable for changing cwa password.
Successfully updated the CWA Engine Configuration file.
Starting database engine opsxmlEng
INFO: Process created
INFO: Started the Database engine : opsxmlEng Retry 0
INFO: Started the Database engine : opsxmlEng Retry 1
INFO: Started the Database engine : opsxmlEng Retry 2
INFO: Started the Database engine : opsxmlEng Retry 3
INFO: Started the Database engine : opsxmlEng Retry 4
INFO: Getting message
INFO: Connect the database DSN=opsxml
ERROR: Cannot connect to the Opsxml database.Can't call method "disconnect" on a
n undefined value at dbRestoreOrig.pl line 334, line 15.
C:\Program Files (x86)\CSCOpx\bin>
so what can I do at this moment ?
plz advice,

LMS 4.2.1 Netconfig job CLI output empty

Hi,
I have run a netconfig jobs in LMS 4.2.1 with these settings:
Task Details
Task: AdhocCommands
show interface status
Devices
switch-1
switch-2
switch-3
Task: AdhocCommands
show versionDevices
-----------switch-1
switch-2
switch-3
After running the job the "Device Details" of the jobs say "Successful Devices" for all three switches:
"Deploy successful (Primary Login Succeeded   / Primary Enable Succeeded )"
For the devices switch-1 and switch-2 I get the desired output:
CLI Output
show interface status
Port      Name               Status       Vlan       Duplex Speed Type
Gi1/1     noz Gi2/17         connected    trunk        full   1000 1000BaseSX
Gi1/2                        notconnect   1            full   1000 1000BaseSX
Gi2/1                        notconnect   1            auto   auto 10/100/1000-TX
But for switch-3 the output is empty:
switch-3
*** Device Details for switch-3                          ***
Protocol ==>                             SSH
Device was successfully                             updated.
Template ==>                                  Adhoc_IOS
CLI Output
Template ==>                                  Adhoc_IOS
CLI Output
Any ideas why there is no output although the job is successful?

You Seems to be using incorrect module of ciscoworks to do this. You are using NetConfig.
Netconfig is one of the Configuration Management applications, and it allows you to change the configuration of network devices, provided the configurations are archived. Netconfig automatically updates the archive when it changes the configuration. When you use it it will try to execute the commands to configure on device and would not be interested in collecting the output.
For show commands you should use the NetShow (Nwtwork Show) module. Network show (NetShow) commands represent a set of read-only commands. These are primarily, show commands that you can run on devices that are managed in LMS.
You can specify the commands that you want to group together and then run these commands on one or many devices. The output is displayed in a browser window.
For more details see the Using NetShow Commands section of Monitoring and Troubleshooting with Cisco Prime LAN Managmement Solution 4.2 guide.
-Thanks
Vinod

LMS 3.2 Invalid license error.

Hi there
I recently installed LMS3.2 in the setup process it asked me for the *.lic file which I provided. I then installed diffrent updates and patches for LMS. LMS is working int the common services tab. but anything else gives me a error: The license file is invalid. Please click this link for information about obtaining a valid purchase license or click here for current licensing information Otherwise, please contact your Cisco representative for purchasing information.
Can anyone give me a tip on how to fix this error and get all the modules working. The license is a full license for all the add ons.
Regards

you need to have to original license file
go to NMSROOT\etc\licenses and backout all the .lic files;
restart dmgtd (on Windows)
net stop crmdmgtd
net start crmdmgtd
after this procedure you should be able to login and re-install the original license file under
Common Services > Server > Admin > Licensing

Prime LMS 4.2.1 Netconfig and Template TFTP/SSH issue

I have cisco Prime 4.2.1 installed and am trying to deploy templates and Adhoc Netconfigs. The jobs are failing with the following message:
Command(s) failed on the device TFTP: Failed on the device. SSH: Failed to establish SSH connection to 10.104.114.231 - Cause: Authentication failed on device 3 times.
If I deploy a Netconfig Task, say just adding a Syslog Server to the same switch it succeeds, no problem.
I am using Cisco ACS 5.2 - TACACS and have configured the tacacspromtps.ini file for the username and password prompt. I can log onto the switch with the Prime Account no problem using Telnet. SSH has not been configured on the switch. I can't find where the protocols for connecting to devices are configured within Prime LMS?

hi gary,
based on my understanding, its because the device is not configured with SSH.
is the device running SSH enabled (K2 or K9) image? if yes, you can enable the SSH.
if no, then perhaps you want to try find it here to change it to telnet
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/user/guide/configuration/appa.html
regards,

LMS 4.0.1 Backup Error Message

LMS installed on Windows 2003.
Backup fais with message "Backup failed.ERROR(1297): Fatal error: Database engine 'UPMDbEngine' could not be started on database 'upm' in Bulk mode.."
dbbackup.log attached.
Any help or explanation is greatly appreciated

Sorry , but for some reason i cannot upload any files ,
This is the process for database reinit
C:\Program Files\CSCOpx\bin>perl.exe dbRestoreOrig.pl dsn=upm dmprefix=UPM
WARNING: Existing contents of upm database will be lost.
Do you want to continue [y/n]?y
INFO: Starting the DataBase
    Starting database engine UPMDbEngine
INFO: Process created
INFO: Started the Database engine : UPMDbEngine Retry 0
INFO: Started the Database engine : UPMDbEngine Retry 1
INFO: Started the Database engine : UPMDbEngine Retry 2
INFO: Started the Database engine : UPMDbEngine Retry 3
INFO: Started the Database engine : UPMDbEngine Retry 4
INFO: Started the Database engine : UPMDbEngine Retry 5
INFO: Started the Database engine : UPMDbEngine Retry 6
INFO: Started the Database engine : UPMDbEngine Retry 7
INFO: Started the Database engine : UPMDbEngine Retry 8
INFO: Started the Database engine : UPMDbEngine Retry 9
INFO: Getting message
INFO: Connect the database dsn=upm
ERROR: Failed to authenticate [upm] database.
Database engine 'UPMDbEngine' could not be started on database 'upm' in Bulk mod
e.Opening C:\PROGRA~1\CSCOpx/dbupdate/CSCOdbupdate.log for logging
    Starting database engine cmfEng
INFO: Process created
INFO: Started the Database engine : cmfEng Retry 0
INFO: Started the Database engine : cmfEng Retry 1
INFO: Started the Database engine : cmfEng Retry 2
INFO: Started the Database engine : cmfEng Retry 3
INFO: Started the Database engine : cmfEng Retry 4
INFO: Started the Database engine : cmfEng Retry 5
INFO: Started the Database engine : cmfEng Retry 6
INFO: Started the Database engine : cmfEng Retry 7
INFO: Started the Database engine : cmfEng Retry 8
INFO: Started the Database engine : cmfEng Retry 9
INFO: Getting message
INFO: Connect the database DSN=cmf
Failed to delete the HUM jobs
Opening C:\PROGRA~1\CSCOpx/dbupdate/CSCOdbupdate.log for logging
    Starting database engine cmfEng
INFO: Process created
INFO: Started the Database engine : cmfEng Retry 0
INFO: Started the Database engine : cmfEng Retry 1
INFO: Started the Database engine : cmfEng Retry 2
INFO: Started the Database engine : cmfEng Retry 3
INFO: Started the Database engine : cmfEng Retry 4
INFO: Started the Database engine : cmfEng Retry 5
INFO: Started the Database engine : cmfEng Retry 6
INFO: Started the Database engine : cmfEng Retry 7
INFO: Started the Database engine : cmfEng Retry 8
INFO: Started the Database engine : cmfEng Retry 9
INFO: Getting message
INFO: Connect the database DSN=cmf
Failed to delete Pidm entries
Data cleanup for upm completed
upm database initialization failed.
C:\Program Files\CSCOpx\bin>
and this is the CSCOdbupdate.log
Beginning DB Update
Start C:\PROGRA~1\CSCOpx\dbupdate\dbupdate.pl : At C:\PROGRA~1\CSCOpx\dbupdate\dbupdate.pl, #48: Time - 2012/06/26 10:59:13
Starting DB ...: Time - 2012/06/26 10:59:13
DSN PRoperties: cmfEng: At C:/PROGRA~1/CSCOpx/dbupdate/dbupdateutils.pl, #119: Time - 2012/06/26 10:59:13
Executing - StartDb(DSN=cmf): At C:/PROGRA~1/CSCOpx/dbupdate/dbupdateutils.pl, #132: Time - 2012/06/26 10:59:13
ERROR: Unable to start DB for dsn=cmf - Database engine 'cmfEng' could not be started on database 'cmfDb' in Bulk mode.: At C:/PROGRA~1/CSCOpx/dbupdate/dbupdateutils.pl, #135: Time - 2012/06/26 11:00:08
Beginning DB Update
Start C:\PROGRA~1\CSCOpx\dbupdate\dbupdate.pl : At C:\PROGRA~1\CSCOpx\dbupdate\dbupdate.pl, #48: Time - 2012/06/26 11:00:09
Starting DB ...: Time - 2012/06/26 11:00:09
DSN PRoperties: cmfEng: At C:/PROGRA~1/CSCOpx/dbupdate/dbupdateutils.pl, #119: Time - 2012/06/26 11:00:09
Executing - StartDb(DSN=cmf): At C:/PROGRA~1/CSCOpx/dbupdate/dbupdateutils.pl, #132: Time - 2012/06/26 11:00:09
ERROR: Unable to start DB for dsn=cmf - Database engine 'cmfEng' could not be started on database 'cmfDb' in Bulk mode.: At C:/PROGRA~1/CSCOpx/dbupdate/dbupdateutils.pl, #135: Time - 2012/06/26 11:01:04

LMS 3.2 Apache 403 Error on CGI Scripts

I've been chasing my tail for a couple of days now, and see no other option than to ask here. It's probably something reall
y dumb that I'm just not seeing.
On a Windows 2008 server with SP1 LMS 3.2 is running fine (as long as no one uses stupid scripts ;o)) on a good day, but whenever I try to access any of the cgi scripts installed under Program Files/CSCOpx/cgi-bin it get the dreaded "You don't have permission to access /cgi-bin/dbadmin/pdbadmin/nph-dbreader.pl on this server". The httpd.conf section for the CGI handling is as follows:
ScriptAlias /cgi-bin/ "D:/PROGRA~2/CSCOpx/cgi-bin/"
<Directory "D:/PROGRA~2/CSCOpx/cgi-bin">
AllowOverride None
Options +ExecCGI
AddHandler cgi-script .pl
#ScriptInterpreterSource Registry-Strict
ScriptInterpreterSource Script
</Directory>
LoadModule perl_module modules/mod_perl.so
What I would like to know is what have I missed..? You can see my first attempt by replacing the ScriptInterpreterSource from Registry-Script to the default, Script, to no avail...
Also, if I make any modifications to the httpd.conf file I cannot just restart the Apache daemon, I have to stop and start the daemon manager, otherwise no one can access the web login page: is that normal..? As in the following:
The Apache daemon is restarted:
[Fri Dec 11 15:14:38 2009] [notice] Child 6088: Child process is running
[Fri Dec 11 15:14:38 2009] [notice] Child 6088: Acquired the start mutex.
[Fri Dec 11 15:14:38 2009] [notice] Child 6088: Starting 500 worker threads.
[Fri Dec 11 15:14:38 2009] [notice] Child 6088: Starting thread to listen on port 1741.
[Fri Dec 11 15:14:38 2009] [notice] Child 6088: Starting thread to listen on port 443.
Lots of the following messages appear in the error.log file:
[Fri Dec 11 15:14:38 2009] [error] [client 10.185.64.101] client denied by server configuration: com.cisco.nm.cmf.servlet.LwmsMainServlet
[Fri Dec 11 15:14:38 2009] [error] [client 10.185.64.101] client denied by server configuration: D:/Program Files/CSCOpx/cgi-bin/error/403.pl
Any help would be most appreciated...
Regards,
Sean

I have no expirience with the W2008 OS yet.
I get the impression it does things differently.
If you know the casuser password, I asume you can try to log onto the server and try an run the perl script in a dos box.
Maybe it will provide a clue.
if you don't know the casuser password you can set it using CSCOpx\bin\resetpasswd.exe.
Cheers,
Michel

LMS 3.2 common services error

Hi all,
I am facing a problem with my LMS 3.2 server. Suddenly I found there is no device reflecing in common services-> device management as well as RME also. I restarted LMS services, server multiple time, reseted casuser, demoted the server from ACS mode to local mode but no luck. However in "dcrcli" i can see all devices and exported all devices to CSV file.
After this I restored from a backup 3 month old when devices were reflecting under common server and RME device management. this also not resolved the problem.
I uninstalled LMS, performed system cleaning and reinstalled LMS 3.2. Then I imported the devices from CSV file i had. Now also the problem not got resolved . I can see devices in dcrcli but none of the device is reflecting under device management of any module.
In Dcmaservice.log i found the error" ERROR,[main],com.cisco.nm.rmeng.config.netshow.server.admin.NSCommandSetManager,getAllCommandSet,8661,Invalid MDF data file:D:/CSCOpx/lib/classpath/com/cisco/nm/cwcs/mdf/mdfdata.xml"
Hence I restored teh mdfdata.xml file from another server. However now i can see the following errors
1) in common service -> software center -> device updae -> device count are 0 for all module
2) no device is reflecting under any module
3) one progress i saw when tring to add any device if selecting device type, it is showing me the list of device type along with OID. before restoring mdfdata.xml it was also not comming.
Please help me to resolve this.

Hi Martin,
Yes you are correct. I did the fresh installation. Imported all devices from the CSV file. However
1) none of these device is showing up in CS>device & credential >device manag
2) Also none of these device are showing up in any other module
3) In Dcrcli i can see al the devices are there
4) for testing I added few device manually. Those are also not showing in any module.
Just to inform all the modules are configured with Auto mode along with manage all devices in Auto Allocation settings under device management.
Thanks & Regards,
Satya

LMS 3.2 dmtgd Startup Error

Running on a Windows 2008 (with SP1) system. The system was running properly until someone tried to run a script they had been using on the previous LMS 3.1 system. Now the daemon manager will not start, and the dmgrDBg.log file has the following entries:
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgrDbg] getenv(PX_MY_TRACE)=[1]
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgrDbg] getenv(PX_DBG_LEVEL)=[1]
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgr-debug]Is this starting the startup service
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgr-debug]CRMDmgtdService::Run
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main] ENTER; argc=1.
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main] argv[0]=[CRMDmgtd]
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main] will daemon_init().
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::daemon_init] ENTER.
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::daemon_init] RETURN 0 (OK).
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main] done daemon_init().
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main] progName=[CRMDmgtd].
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main] will new CatLogMsg(SYSLOG).
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main] done new CatLogMsg(SYSLOG).
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main]; will new CStartup().
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main]; done new CStartup().
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main]; <NT> will theStartup->CreateUserToken().
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main]; <NT> ERROR >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main]; <NT> CreateUserToken() failed; lastError=0x00000569.
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main]; <NT> CreateUserToken() failed; log msg#2507.
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::cleanUp] ENTER.
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::cleanUp] will delete theStartup.
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::cleanUp] will delete theLog.
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::cleanUp] RETURN void.
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgrDbg][dmgtd.cpp::main]; <NT> CreateUserToken() failed; RETURN EXIT_FAILURE=1.
[Tue Dec 08 09:00:03 W. Europe Standard Time 2009][dmgr-debug]Is service stopped
Short of rebuilding the system from scratch, how can I identify what is wrong and how to fix it..?
Cheers,
SRGi

The issue was not the password, but the security settings. It seems someone decided to remove the assignment "Log on as a batch job" from the CASUSER rights... The script itself is a simple perl script that calls DCRCLI to perform additions or deletions...

The LMS 4.1 show message error license.

The click logs critical show message "This software is provided for evaluation purposes only and had expired. If this is not an evaluation copy, please click this link for information about obtaining a valid purchase license or click here for current licensing information Otherwise, please contact your Cisco representative for purchasing information". However, while in the menu Admin>System>License Management show the license "Purchaded" and "Never Expiration". Not know error this license show, I am remember duration instalation of LMS the file .lic export sucess.
Please, see the file is attached: LMS1.png and LMS2.png. show screeshot the message.

Hi ,
Hope you would have the copy of the license with you . if yes , Re-apply the License
Please follow the below steps to Installed the new License File:
1. Stop the Licensing server by issuing the command:
pdterm LicenseServer
2. Check to make sure the Licensing server has stopped by issuing the command:
pdshow LicenseServer
3. Place this new License(LMS2014xxxxxx.lic) file on the Cisco works server . CAUTION !!! This file is emailed to you from Cisco. This file's name should be in the form of LMS2014xxxxxx.lic, and this file MUST NOT be located at your
CSCOpx\etc\licenses directory. If you have found any file at CSCOpx\etc\licenses directory then please move this file to another directory.
4. Go to the CSCOpx\etc\licenses directory and delete all the *.lic files (If any)
5. Start the Licensing server by issuing the command:
pdexec LicenseServer
6. Check to make sure the Licensing server has started by issuing the command:
pdshow LicenseServer
7. On your LMS 4.0 GUI go to Admin -> Licensing. Click the "Update" box -> In the pop-up window indicate the path where the new license file is located and -> Click "OK".
This will generate the license in the form that LMS 4.0 will recognize.
Thanks-
Afroz
*****Ratings Encourages Contributors ****

CISCOWORKS - RME netconfig error

When I go to RME>Config Mgnt>NetConfig>User-Define Task i receive the follow error:
CFG0053: No User-defined tasks are available.
I don't can do any configuration.
the version of RME is 4.1.1 and the licence is for 100 equipments, I must update the module? or someone know why appear this error?

I think the problem is more serious
as seen, does not allow me create any task: in the menu, "Tasks" on the left can not deploy any device.
When i go create a task in RME>Config Mgmt>Netconfig>Netconfig jobs i cant not select ALL the devices as shown in the picture below: the host ING_C58_Sw_P2_03 can not choose, instead the other can choose
which will be the cause?

LMS 3.2 gives Application error during Campur User tracking

Hi All,
As per the subject during Campus User Tracking following error comes.
Application error: URN_NOT_FOUND : urn "ogs_server_urn" : Not found !!..
Please let me know if anybody has solution for this.
Thanks in advance.
Samir

this looks like CSCsz79649
I assume at least one of the ctm_config.txt files became corrupted.
have a look at the file ctm_config.txt in both these locations:
    NMSROOT/MDC/tomcat/webapps/campus/WEB-INFlib
    NMSROOT/MDC/tomcat/webapps/cmapps/WEB-INF/lib
and compare the content to the clean files Joe posted in this thread:
    https://supportforums.cisco.com/message/3153454#3153454
Note: the parameter DYNAMIC_PORT_ALLOCATION=0 can be added to both files;
If your files (or at least one) are different, then stop the daemon manager. When services are stopped, replace the corrupted file with the one Joe posted. Also move the ctmregistry and ctmregistry.backup files in these directories to a location outside NMSROOT (like C:\Windos\tmp)
Restart the daemon manager.
If everything is working you can remove the ctmregistry and ctmregisry.backup files you previously moved to C:\Windows\tmp

LMS 4.2.5 Netconfig changing port config based on port settings

I am trying to use netconfig to change the port config on my switches. I want to use an adhoc rule to determine if the port already is configured for 802.1x (authentication port-control auto) authentication and then modify those ports to "authentication open".
IS that possible?
Thank you for your reaction?
Regards,
Robert

Hi Robert,
To check which device have this config , use Baseline Template
check the below link for example and case study.
Hope it will help
Thanks-
Afroz
***Ratings Encourages Contributors ***

LMS 3.2 - unknow SNMP error for Cisco XR12406

Hi ,
I got a RME job alert which describes SNMP RW community verification failure in Device Credentials Verification for Cisco XR12406 router, I have double checked on the credential configured in LMS and it is correct.
The configuration that i tried in XR12406:
snmp-server community T3lBruRW RW <acl>   ---> not working
snmp-server community T3lBruRW RW SystemOwner <acl> ---> not working
Anyone can help!!!

Hi Nael, here it is:
#sh ver
Sun Nov 28 15:43:14.648 BNT
Cisco IOS XR Software, Version 3.8.2[00]
Copyright (c) 2009 by Cisco Systems, Inc.
ROM: System Bootstrap, Version 12.0(20060713:113510) [sunnaik-31s5th 1.16dev(0.1)] DEVELOPMENT SOFTWARE
Copyright (c) 1994-2006 by cisco Systems, Inc.
CRTH uptime is 8 weeks, 2 days, 20 hours, 45 minutes
System image file is "disk0:c12k-os-mbi-3.8.2/mbiprp-rp.vm"
cisco 12406/PRP (7457) processor with 2097152K bytes of memory.
7457 processor at 1266Mhz, Revision 1.2
3 Cisco 12000 Series SPA Interface Processor-601/501/401
2 Cisco 12000 Series Performance Route Processors
6 Management Ethernet
12 PLIM_QOS
4 TenGigE
15 GigabitEthernet/IEEE 802.3 interface(s)
1018k bytes of non-volatile configuration memory.
1998M bytes of compact flash card.
2048800k bytes of disk0: (Sector size 512 bytes).
65536k bytes of Flash internal SIMM (Sector size 256k).
Boot device on node 0/0/CPU0 is mem:
Package active on node 0/0/CPU0:
c12k-k9sec, V 3.8.2[00], Cisco Systems, at disk0:c12k-k9sec-3.8.2
    Built on Wed Oct 28 19:00:47 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-lc, V 3.8.2[00], Cisco Systems, at disk0:c12k-lc-3.8.2
    Built on Wed Oct 28 16:27:50 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-fwdg, V 3.8.2[00], Cisco Systems, at disk0:c12k-fwdg-3.8.2
    Built on Wed Oct 28 16:26:44 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-admin, V 3.8.2[00], Cisco Systems, at disk0:c12k-admin-3.8.2
    Built on Wed Oct 28 16:25:55 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-base, V 3.8.2[00], Cisco Systems, at disk0:c12k-base-3.8.2
    Built on Wed Oct 28 16:24:15 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-os-mbi, V 3.8.2[00], Cisco Systems, at disk0:c12k-os-mbi-3.8.2
    Built on Wed Oct 28 16:19:12 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
Boot device on node 0/1/CPU0 is mem:
Package active on node 0/1/CPU0:
c12k-k9sec, V 3.8.2[00], Cisco Systems, at disk0:c12k-k9sec-3.8.2
    Built on Wed Oct 28 19:00:47 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-lc, V 3.8.2[00], Cisco Systems, at disk0:c12k-lc-3.8.2
    Built on Wed Oct 28 16:27:50 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-fwdg, V 3.8.2[00], Cisco Systems, at disk0:c12k-fwdg-3.8.2
    Built on Wed Oct 28 16:26:44 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-admin, V 3.8.2[00], Cisco Systems, at disk0:c12k-admin-3.8.2
    Built on Wed Oct 28 16:25:55 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-base, V 3.8.2[00], Cisco Systems, at disk0:c12k-base-3.8.2
    Built on Wed Oct 28 16:24:15 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-os-mbi, V 3.8.2[00], Cisco Systems, at disk0:c12k-os-mbi-3.8.2
    Built on Wed Oct 28 16:19:12 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
Boot device on node 0/2/CPU0 is mem:
Package active on node 0/2/CPU0:
c12k-k9sec, V 3.8.2[00], Cisco Systems, at disk0:c12k-k9sec-3.8.2
    Built on Wed Oct 28 19:00:47 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-lc, V 3.8.2[00], Cisco Systems, at disk0:c12k-lc-3.8.2
    Built on Wed Oct 28 16:27:50 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-fwdg, V 3.8.2[00], Cisco Systems, at disk0:c12k-fwdg-3.8.2
    Built on Wed Oct 28 16:26:44 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-admin, V 3.8.2[00], Cisco Systems, at disk0:c12k-admin-3.8.2
    Built on Wed Oct 28 16:25:55 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-base, V 3.8.2[00], Cisco Systems, at disk0:c12k-base-3.8.2
    Built on Wed Oct 28 16:24:15 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-os-mbi, V 3.8.2[00], Cisco Systems, at disk0:c12k-os-mbi-3.8.2
    Built on Wed Oct 28 16:19:12 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
Configuration register on node 0/4/CPU0 is 0x2102
Boot device on node 0/4/CPU0 is disk0:
Package active on node 0/4/CPU0:
c12k-k9sec, V 3.8.2[00], Cisco Systems, at disk0:c12k-k9sec-3.8.2
    Built on Wed Oct 28 19:00:47 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-rout-3.8.2.CSCti62211, V 1.0.0[SMU], Cisco Systems, at disk0:c12k-rout-3.8.2.CSCti62211-1.0.0
    Built on Sat Aug 28 15:36:26 BNT 2010
    By edde-bld1 in /vws/afz/builds/smu_r38x_3_8_2/workspace for c4.2.1-p0
c12k-rout, V 3.8.2[00], Cisco Systems, at disk0:c12k-rout-3.8.2
    Built on Wed Oct 28 16:28:36 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-lc, V 3.8.2[00], Cisco Systems, at disk0:c12k-lc-3.8.2
    Built on Wed Oct 28 16:27:50 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-fwdg, V 3.8.2[00], Cisco Systems, at disk0:c12k-fwdg-3.8.2
    Built on Wed Oct 28 16:26:44 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-admin, V 3.8.2[00], Cisco Systems, at disk0:c12k-admin-3.8.2
    Built on Wed Oct 28 16:25:55 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-base, V 3.8.2[00], Cisco Systems, at disk0:c12k-base-3.8.2
    Built on Wed Oct 28 16:24:15 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-os-mbi, V 3.8.2[00], Cisco Systems, at disk0:c12k-os-mbi-3.8.2
    Built on Wed Oct 28 16:19:12 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
Configuration register on node 0/5/CPU0 is 0x2102
Boot device on node 0/5/CPU0 is disk0:
Package active on node 0/5/CPU0:
c12k-k9sec, V 3.8.2[00], Cisco Systems, at disk0:c12k-k9sec-3.8.2
    Built on Wed Oct 28 19:00:47 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-rout-3.8.2.CSCti62211, V 1.0.0[SMU], Cisco Systems, at disk0:c12k-rout-3.8.2.CSCti62211-1.0.0
    Built on Sat Aug 28 15:36:26 BNT 2010
    By edde-bld1 in /vws/afz/builds/smu_r38x_3_8_2/workspace for c4.2.1-p0
c12k-rout, V 3.8.2[00], Cisco Systems, at disk0:c12k-rout-3.8.2
    Built on Wed Oct 28 16:28:36 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-lc, V 3.8.2[00], Cisco Systems, at disk0:c12k-lc-3.8.2
    Built on Wed Oct 28 16:27:50 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-fwdg, V 3.8.2[00], Cisco Systems, at disk0:c12k-fwdg-3.8.2
    Built on Wed Oct 28 16:26:44 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-admin, V 3.8.2[00], Cisco Systems, at disk0:c12k-admin-3.8.2
    Built on Wed Oct 28 16:25:55 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-base, V 3.8.2[00], Cisco Systems, at disk0:c12k-base-3.8.2
    Built on Wed Oct 28 16:24:15 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0
c12k-os-mbi, V 3.8.2[00], Cisco Systems, at disk0:c12k-os-mbi-3.8.2
    Built on Wed Oct 28 16:19:12 BNT 2009
    By edde-bld1 in /auto/srcarchive3/production/3.8.2/c12k/workspace for c4.2.1-p0

LMS 3.2 Syslog Collector error

Hi,
At RME: ToolsSyslogSyslog Collector Status screen at table Collector Status No records.
I had changed hostname on this server and i have ran /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/hostnamechange.pl script with proprer parameters.
Now I cannot add collector, because of "SSL certificate status" error:
SSL certificate issue occurred, check if:
1. The Self-signed Certificates are valid. For example, Check the certificate expiry date on the servers.
2. The Self-signed Certificates of this server are copied to the Syslog Collector server and vice-versa.
To do this, go to Common Services > Server > Security > Multi-Server Trust Management > Peer Server Certificate Setup. and add the certificate. See the User Guide for CiscoWorks Common Services for more details..
3.The SyslogCollector process on Syslog Collector server and the SyslogAnalyzer process in the current working server are restarted after Step 2.
4.Both hosts are reachable by host name.
Collector status : Could not connect to the collector _myhostname_._mydomainname_ due to SSL certificate issue
I use an third party Certificate, and https access is working propery for user access.
I want to run Syslog Collector locally, syslog file is a local server hence I use syslog-ng for other reason.
This is my SyslogCollector log:
SyslogCollector - [Thread: main] INFO , 24 Mar 2011 16:47:45,305, Logging System Initialized.
SyslogCollector - [Thread: main] INFO , 24 Mar 2011 16:47:45,308, System Initialized.
SyslogCollector - [Thread: main] INFO , 24 Mar 2011 16:47:45,408, Queue Cap 100000
SyslogCollector - [Thread: main] INFO , 24 Mar 2011 16:47:47,699, Service started...
How can I correct this situation, how can I run Syslog Collector.
Balazs

Try unsubscribing and subscribing the collector so it can accept the updated info. If that does not work, post the SyslogAnalyzerUI.log and SyslogCollector.log from CSCOpx/log directory.

LMS 3.2.1 netconfig error

Similar Messages

Maybe you are looking for