LMS 3.2 - snmp-write needed ?

Hello,
we are testing currently LMS 3.2 for a very large installation. In our network snmp-write access to devices is currently forbidden by a special company policy. The devices can only contacted via snmp-read and telnet/ssh.
So my questions is:
For which functions does LMS 3.2 realy need snmp-write access to the devices ? Or can I use telnet/ssh intead of snmp-write always ?
Thx + Best regards
Hendrik

CiscoView also requires the SNMP read-write for most its configuration tasks (some can use telnet/SSH).  This is not nearly as show-stopping as IPM, though.  IPM is pretty much useless without SNMP read-write.  But note, that community string-based SNMP is no longer required in LMS.  You can move to SNMPv3, and be able to do SET operations in a more secure manner.

Similar Messages

  • ACL to secure SNMP - I need help on this please

    Hi,
    I have addedd the following standard ACL to my router to limit SNMP access only to my Ciscoworks LMS server or SNMP Server but I don't know if I need to enforce it with an access group or not? i beleive that i need but I am not sure how?
    access-list 90 permit host 10.1.1.139
    access-list 90 deny any log
    snmp-server community XXXXXXX ro 90
    please help me understand the need for the access-group and if I need it, would it be sonething like this:
    access-grup 90 in
    applied to ether Interface?
    this is my Internal gateway router. all of the users have the ether0 address of this router as their default gateway.
    Thx,
    Masood

    I believe that Masood starts from a valid understanding of an important principle of access lists: after you create an access list you must assign it (creating an access list without assigning it does not affect any traffic). If you want the access list to filter packets on an interface you use the access-group command to assign the access list to the interface.
    And Tim is correct that to use an access list to control SNMP access to the router all you need to do is to add the access list number on the command that defines the community string. This is the assignment of the access list. So Masood does not need to take any additional action.
    HTH
    Rick

  • Cisco Works SNMP write community string Incorrect

    Hi,
    I have installed Cisco Works at my organisation. Under RME -> Inventory -> Import status -> Device Attribute Error: I am getting: Incorrect SNMP write community strings. Even though i know perfectly well the SNMP write community string is correct. To prove that, if I delete the device and then add the same device using the same SNMP write community string it works fine. then a couple of days later, it comes up with the same message "SNMP write community string is incorrect". I have increased the time and retries for the SNMP settings at the ANI server, still it has not resolved the issue.
    Please help

    I have sharched the CCO bug toolkit and according them, it was a know issue for verion 3.4 but it has been fixed for Ver RME 3.5. But we are currently running RME 3.5, therefore it does not make any sense.

  • Shutdown wireless interface via SNMP Write?

    Hi
    We're working on writing a very simple web app to control a couple of access points via SNMP.  I'm trying to shutdown the Wireless interface via SNMP WRITE with the following oid;
    .1.3.6.1.2.1.2.2.1.7.1
    and
    .1.3.6.1.2.1.2.2.1.7.2
    But its saying the integer of '0' is invalid (badValue, wrong type or length).  I'm able to set other values like hostname, etc, so I know my string is correct...can anyone help?  THanks
    Jason

    Hi
    Just found my own answer...the value to shutdown the interface is not 0, it's 2.  durrr
    Thanks
    J

  • HT201441 i buy used iphone 5s from japan and when i do activated it write need apple id and i no have that id because i buy from japan and i know in lebanon pleas tell me what i do

    i buy used iphone 5s from japan and when i do activated it write need apple id and i no have that id because i buy from japan and i know in lebanon pleas tell me what i do

    There is not a thing you can do except get the Apple ID and password of the previous owner...that iPhone is in Activation Lock mode and cannot be unlocked any other way.  The Activation Lock is an anti-theft protection that cannot be bypassed.  You very well may have a stolen iPhone so try contacting the who you bought it from and get your money back.

  • LMS 3.2 snmp trap forwardig to HP-open view

    Hi,
    I want to forward snmp traps from cisco LMS to HP-open view. Both applications are installed on different servers.
    From previous post in this forum, I found a similar post that recommand using snmp forwording in DFM.
    What I want to know is do I need any integration or packages to install on both platforms to do this? Also, will DFM forward all traps that it receives from installed devices or it will forward some of them.
    Thank you
    BR,
    ZS

    Chris;
       current version of Java is 1.6.0 Update 20
    Additional information to the issue:  a WS-C3750 has been discovered (connected to another 6509 that is running hybrid) and added to the topology map as it one would expect.
    craig

  • Does LMS 3.2 still use need rcp enabled on our devices?

    LMS 3.2 running on Unix in a master-slave configuration.
    Our security team is asking us why we need rcp (port 514) enabled on our routers.
    It's becuase of the following standard commands;
    ip rcmd rcp-enable
    ip rcmd remote-host cwuser <ip address of LMS> cwuser enable
    I believe these commands helped with the archiving of the device configurations? I know it's been a standard command of ours for years, but am not sure if it is still needed?
    Any information you can provide would help.
    Thanks,

    RCP is optional.  If you would rather use TFTP, SSH, SCP, etc. you can disable RCP.  By default, LMS/RME will use TFTP, TELNET, and SSH for config archive.

  • Freelance writer needs database software to organize, manage contact lists

    Hello, and thank you in advance for helping me solve my problem--
    I am a freelance writer in need of a better way of organizing my contact lists. I currently have two major lists to manage.
    The first is a simple list of business, medical, and educational contacts I use regularly in my research and writing.
    The second is a list of business people that need to be contacted in a nine month rotation to be featured in a publication I write for. I would like the software to help me keep track of whose turn it is to be featured, as well as their contact information.
    While I could probably use AppleWorks for this function, I have found this program to be PAINFULLY slow. I also have Microsoft Entourage, but I don't want to mingle these lists together, or with my address book in Entourage.
    And, naturally, I don't want to spend a fortune.
    Thoughts?

    I also have Microsoft Entourage, but I don't want to mingle these lists together, or with my address book in Entourage.
    If Entourage will do what you want, just set up another account on your iBook (System Preferences>Accounts) just for your writing and use your existing account (and Entourage) for personal use. The Microsoft User Accounts will be completely seperate.
    John

  • LMS 4.0 SNMP Traps Forwarding

    Hello,
    I have installed a new version of CiscoWorks LMS 4.0.
    I would like to forward certain SNMP traps to another server. Not all traps but only the traps of devices which are down.
    Is it possible to filter the traps and then forward the traps who match the filter to a server?
    Thanks,
    Best Regards,
    Joris

    If you enable trap forwarding in LMS, all traps received by LMS will be forwarded to the external NMS.
    You can, however, look at NMSROOT/objects/smarts/conf/trapd/trapd.conf.  You can modify this file to specify exactly what traps to forward.  The comments in the file should help you figure out the syntax.  However, direct modification of this file is not supported by TAC, so be sure to save a backup just in case.

  • SNMP Monitoring needs

    Hi ppl,
    We need to check the average use of ejb beans of one of our components. Looking in the SNMP MIB documentation, I found the ejbStatelessHomeRuntimeTable entry, that satisfy my needs. When I do a lookup for this MIB, nothing returns.
    Looking in other posts in the forum, one of them say that that MIB was wrongly published and is no longer available.
    I'd like to know if there's a similar SNMP MIB that I can use to monitor the beans in use and available of my application.
    Thanks in advance and sorry for my bad english.
    Regards,
    Miguel Figueiredo

    Hello Miguel,
    Can you provide the command you used to retrive the EJBRuntime info? Did you try the snmpget?
    It is not true that BEA does not publish it's MIB, it is published and available on edocs.
    Thanks,
    -satya

  • Re: Satellite A500-1DN - Blu-Ray disc Writer needed

    Hi all!
    My problem is that in my latop i have a CDDVDW TSST TS-L633C writer.
    With this i can 't record or play blu-ray content.
    Is this possibility to get a blu-ray disc writer in my laptop from toshiba? If yes, how much does it cost?
    Thanks in advance!
    atibrd

    Hello
    Unfortunately I cannot give you presice info about that but what I know is that just several Toshiba notebooks are delivered with Blu-Ray disc drives and I was not able to find any info about Blu-Ray driver used on A500.
    On my Satellite P500 I have Mat****a BD-MLT UJ240ES and this drive has BD read and write function. I dont know if you can use this ODD on your notebook model (compatibility).
    I recommend you to contact Toshiba service in your country and ask for help. They should know if you can use this ODD or not.
    Price? Google!!!

  • Problem in query writting , Need a help on priority

    Hi there,
    Please check the following scenario
    there are 2 tables
    event - eventId , userId and eventDate
    impression - impressionId,userId
    After joining -
    userId | impressionId | eventId | eventDate
    1 | 1 | null | null
    1 | 2 | null | null
    1 | 3 | 1 | 2007/08/10
    1 | 4 | null | null
    1 | 5 | null | null
    1 | 6 | null | null
    1 | 7 | 2 | 2007/08/10
    I want the following output to be generated.
    userId | impressionPosition | eventCnt
    1 | 3 | 1
    1 | 4 | 1 (2nd event occured AFTER 4 impressions)
    Please give some query clue or sample query.
    Thanks in Adv.
    -Amol Kashid

    you just need to add a partition clause to the analytic function:
    with t as (select 1 as userid, 1 as impressionid, null as eventid, null as eventdate from dual
    union all select 1, 2,null, null from dual
    union all select 1, 3,1, sysdate-5 from dual
    union all select 1, 4,null, null from dual
    union all select 1, 5,null, null from dual
    union all select 2, 6,2, sysdate from dual
    union all select 1, 7,2, sysdate from dual
    union all select 2, 8,2, sysdate from dual)
    select userid, count(*) over(partition by userid order by impressionid) event_sequence,
                                          'Event after '||
                                          to_char(nvl(impressionid - lag(impressionid) over (partition by userid order by impressionid),0))
                                          ||' impression(s)' as description
      from t
      where eventid is not null
        USERID EVENT_SEQUENCE DESCRIPTION
             1              1 Event after 0 impression(s)
             1              2 Event after 4 impression(s)
             2              1 Event after 0 impression(s)
             2              2 Event after 2 impression(s)
    4 rows selected.edit: actually, that screwed up the reporting of the first event.... hmmm....

  • I am a writer, need help with software

    Hello,
    I am a writer, and am working on a book in Hebrew. I purchased a Mac last year, and for a long time I did a an extensive search for a software that will allow me to write in Hebrew. Nothing that was out there enabled me to write smoothly in Hebrew without messing up the documents somehow, besides Open Office. I used version 2.3
    Everything was fine until 9/16/08
    Suddenly, it is not working. X11 opens up, and then it gives me the regular "command timed out", but then, it just sits there. I can only Force Quit it. It wouldn't quit regularly.
    I tried downloading 2.4 version but that's doing the same thing.
    Version 3 is working, but is completely messing up the sentences in Hebrew.
    I see that someone else had the same problem, I suspect it has something to do with the Mac OS X 10.5.5 system update that was installed on my computer on 9/16/08.
    Does anyone have a solution?
    I am stuck, and can't go further with my book until I can fix this.
    Please let me know.
    Thank, Too-Ticky.

    Nothing that was out there enabled me to write smoothly in Hebrew without messing up the documents somehow, besides Open Office. I used version 2.3
    I think most people would use Mellel for such work. Did you really find that unsatisfactory? How about StarOffice or Nisus Writer?
    I suspect it has something to do with the Mac OS X 10.5.5 system update that was installed on my computer on 9/16/08.
    That may well be the case. Personally I think it is better not to apply minor updates if you depend on X11 apps, as it is too easy for something to get broken. As a last resort you might try going back to whatever OS version you were last using when things worked correctly.

  • Oracle 10g AS report writer needs InfraStructure?

    We need to install Oracle 10g AS on HP-UNIX. But the requirement would be only Forms & Report Services (Business Intelligence). The reports will be web based and as well as it will be generated using rwrun command line utility. Therefore is it enough to have "Oracle application server Forms and Reports services" installation alone or we need to install the "Infrastructure" in addition to this?
    Can any one help on this?

    Hi,
    You need to install infrastructure first to install the Forms & Reports. Actually, OID gets installed with infrastructure, and thus need to install it.
    SSO will be on for the report server, thus when you use rwclient or rwrun you have to use the authid.
    Regards,
    Soumyajit

  • Ciscoworks lms 2.6 snmp trap notification

    Hi
    Can anyone help with a problem I'm having, how do you go about setting up an alert email notification for a logging event coming from a firewall? The logging event is an alert.

    Is this alert in the form of a syslog message?  If so, then you can configure an RME Automated Action under RME > Tools > Syslog > Automated Actions.  Fill in the desired facility, severity, and mnemonic, then set the type of Action to be email.

Maybe you are looking for