LMS 4.1 Credential Verification Report

Hi,
when running Credential Verification Report, I get following notification: "None of the devices have credential verification data".
I have made different Default Device Credential sets that I'm using when I add devices to LMS. I been looking at the forums here, but I could not see wether this is bug in LMS 4.1 or if I have to do this a different way?
Regards,

I'd suggest doublechecking your work by following the "Update the credentials" procedure on page 8 of this handy intro guide posted in the documents section of this forum.
Hope this helps.

Similar Messages

  • RME Device Credential Verification Report

    I have a Device Credential Verification Job which runs each week. It has run fine for the last few months, however, this week the job started but didn't finish and appears to have hung.
    The job usually takes around 25mins to run (circa 350 devices) but this week it was still running after 19 hours. Eventually I tried to stop the job but it is now stuck in a state of "Stop Initiating".
    I've stopped/started the services and evenutallty even rebooted server but this particular job remains stuck in "Stop Initiating" state.
    Is there any way to fix this?

    Hi Joe,
    LMS3.2.
    The job is validating SNMP/v2c Read & Write, Telnet and Telnet Enable.

  • Sending Ciscowrks device credential Verification Job alters the device ARP table.

    Hi:
    I send a Device credential verification Job to two different devices  , a Cisco 3750 and a blade switch WS-CBS3120. I  configured SNMP write access to the switches. The SNMP write access in either SNMP v1 or SNMP V3 , tried both.
    The job is send from the Ciscoworks server.
    Once the job has completed, I do a show ip arp on the device and find a new entry with the IP address of the Ciscoworks  Server and the mac-address of the L2 next hop.
    We would not have  noticed this behavior had it not been that in the case that the  switch  next hop is an HSRP vlan on a nexus , the ARP entry entered into the switch is incorrect, and from then on the switch loses connection to Ciscoworks.
    The Mac-address that is entered by Ciscoworks , in the case of nexus is a statice mac defined on the Nexus for the Vlan in question , but it is NOT the HSRP default gateway MAC address. Therefore we lose connection between the switch and Ciscoworks. One has to manually clear the ARP table inorder to again reach the Ciscoworks.
    Questions:
    1. Why does Ciscoworks  insist on changing the ARP table?
    2. Is this ARP entry aged out or is it permeant as would an ARP entry which is entered through CLI  be  permeant ?   
    3. In the case of the Nexus connection, this ARP entry does not allow Ciscoworks and the device to communicate. This is not productive!
    Has any one come across this situation ? Any known fixes, workarround? I was not able to find a word about this on Cisco's site.
    Our Ciscoworks is at the following levels:
    CW Common services    3.3.0
    LMS portal                    1.2.0
    CW Assistent                1.2.0
    RME                             4.3.1
    Device fault manager      3.2.0
    IPM                              4.2.1
    Cisco View                    6.1.9
    campus Manager            5.2.1
    thanks   for any help
    Mickey

    CiscoWorks does not change the ARP table, at least not overtly.  A credential verification job will do the following things depending on what protocols are selected to test:
    SNMP RO : Fetches sysLocation.0
    SNMP RW : Sets sysLocation.0 to the value currently stored in sysLocation.0
    Telnet : Logs in using DCR username and password
    SSH : Logs in using DCR username and password
    Enable : Enters enable mode and verifies privilege level 15
    If one of these things are causing the ARP table to change, then there is something fishy in the device or network configuration.  I've never heard of such behavior relating to CiscoWorks before.

  • Device Credential Verification Job Error

                  When starting Device Credential Verification Job, we have following error:
    CDA0114: Operation failed while connecting to JRM. Make sure jrm and/or CTMJrmWrapper services are up and running.
    In cda.log, there is error:
    com.cisco.nm.xms.ctm.common.CTMException: URN_NOT_FOUND : urn "JRM" : Not found !!
    How could we proceed to solve these problems?
    We have LMS3.2.1 installed on Windows 2003 Standard Edition server.
    Please find attached log files.

    Hello,
    I have a similar problem. I have configured a snmp v3 user using SHA to authentication an DES for private access.
    We use RME 5.0.1 and when we try to run a CDA it doesn`t work reporting "Error performing SNMP operation".
    In the log of the CDA job, we can see:
    [ lun nov 26  16:46:06 CET 2012 ],INFO ,[Thread-6],com.cisco.nm.rmeng.inventory.cda.job.DoCDAonDevice,updateCdaStatus,1784,Executing sqlStmt update DM_Credential_Error_Status set Cred_Status= 8 ,Cred_Status_Descr='Error performing SNMP operation.',Update_At='1353944766699' where NetworkElementID = 3685 and Cred_Type = 3
    How can I use snmp v3 with RME 5.0.1?
    Thanks.

  • Device Credential Verification Job

    I have a device credential verification job which runs one per week.
    Every now and again the job hangs and no matter what I do I can't stop the job to delete it. I can see the job in the job list and I can select it and choose STOP, howeverm after that the job stick in a "Stop Initiated" state and never changes. I've tried rebooting the server and this doesn't affect the job state or my inability to delete the job.
    I can successfully create another Device Credential Verification Job and these run fine for several weeks.
    Two questions.
    1. Any idea's what's causing the job to hang
    2. How can I delete the jobs that are stuck in a "stop initiating" state
    Thanks,

    It may be that you will need to get TAC involved to clean the job out of the database directly.  However, you can try the following first.  Run the "pdshow" command, and check for a daemon named the same as the job ID.  If you see it, run:
    pdreg -u JOB_ID
    That should unregister the job daemon.  Then see if you can stop and delete the job.

  • Purchase requisition and invoice verification report

    Hi,
    pls. I need to display a report with purchase requisition and invoice verification pending, what I mean is an standard trx. to display purchase requisition with or without invoice verification.
    Thanks for cooperation.
    Regards.

    hi
    I guess thereis no standard report which combines both. You have to go for a Z-report. use the details FROM Txns ME5A &  MB5S for your requirement.
    Regards

  • LMS 3.2 SP1 - Syslog Report times out / CW14: NO HTTP response

    Hi,
    in Device Center I can´t start the Syslog Report, it opens a new Browser window and times out.
    If I start the "Device Troubleshooting" from the Device Center, all checks are successful. Just the check "Syslog Message" show the error: CW14: NO HTTP response from Servername
    I have LMS 3.2 SP 1 installed
    I already re set the System Identity User and restarted the daemon, no success.
    What should I check? Is it a known problem ?
    Best regards,
    Patrick
    UP

    Hey,
    i maybe found the failure.
    In the dir "CSCOpx\databases\rmeng" the following files are very big.
    So I started a immediate syslog purge job, but it failed.
     [ Thu Jul 28  09:00:33 CEST 2011 ],INFO ,[main],Starting purge job 5349
     [ Thu Jul 28  09:00:33 CEST 2011 ],INFO ,[main], Its a force Purge job
     [ Thu Jul 28  09:02:21 CEST 2011 ],ERROR,[main],Drop table failed:SQL Anywhere Error -210: User 'DBA' has the row in 'SYSLOG_20110627' locked 8405 42W18
     [ Thu Jul 28  09:02:21 CEST 2011 ],ERROR,[main],Failed to purge syslogs
     [ Thu Jul 28  09:02:22 CEST 2011 ],ERROR,[main],Purge not successful
    Can anyone say me, how to fix it?
    Best regards
    Patrick

  • LMS 4.2.2 DOT1X Report

    Hi, i need a lms report to know if service dot1x  on the switchs in my lan is enable.
    Thanks a lot.
    Emiliano

    Thank you for your answer, but I need not have a report or PC user who authenticates dot1x but if the service is enabled. example:
    a report that show dot1x: enable or disable
    Thanks
    Emiliano

  • LMS 4.2 , Subnet's Report

    Hi Guys
    How to generate a Report for all ur existence  Subnet's using LMS 4.2?
    thanks
    Ibrahim

    Ibrahim,
    You can get a report of all VLANs. It's not exactly the same thing but it the closest thing available in LMS. Here are the details for the VLAN report:
    http://www.cisco.com/en/US/customer/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/user/guide/reports/tech_reports.html#wp1265257
    To get all subnets and used addresses etc., you'd need an IP address management tool. Something like SolarWinds IPAM.

  • Ciscoworks LMS 3.2 bug summary report

    Hi,
    I have one Ciscoworks LMS 3.2, it managed around 500 devices. I tried to generate bug summary report and the bug number is zero. Please kindly help to solve this problem.
    Best Regards,
    Jackson Ku                  

    For how many devices are you running the report?
    [ Wed Jan 05  21:26:50 CST 2011 ],INFO ,[main],com.cisco.nm.rmeng.bugtool.BTBugSummary,populateResults,295,Cisco.com URL Connection TimeOut: Try again later or with less number of devices.
    Have you tried running it for just one?
    This is also kind of strange,
    [ Wed Jan 05  21:26:50 CST 2011 ],INFO ,[main],com.cisco.nm.rmeng.bugtool.BTBugSummary,formBTDevHash,228,Device(s) are not supported by Cisco.com.
    [ Wed Jan 05  21:26:50 CST 2011 ],INFO ,[main],com.cisco.nm.rmeng.bugtool.BTBugSummary,formBTDevHash,229,Hence Could not generate report
    Like as if cisco.com would not know about these C3750's
    Maybe do an export of these 3750's in the DCR to see if the all have the same OID and if it is a supported OID.
    Are your device packages up to date? You may want to sync those with CCO.
    Cheers,
    Michel

  • LMS 4.2 - CPU Utilization Reports

    We have CPU reports set to run daily for some of our higher priority switches, and we've noticed that some of the data isn't meshing with what we see on the switch. We have one heavily utilized switch that reports near 100% CPU utilization sometimes. I can do a "show proc cpu history" on that switch and see that at least once an hour over 72 hours, we'll see a near 100% CPU utilization.
    The problem is that these spikes never appeare on any of our reports. We'd like to see this info because even if the switch spikes for just a few seconds or a minute, it could still indicate that we may have issues. Without that in the report, we may never realize there could be a problem.
    Is there a way for this info to show in the report? I'm under the impression that if LMS polls the switch and doesn't see a high utilization average, then maybe it doesnt' enter that in the report. I guess I'd just like to know how often it pulls this data, and how it decides wath the Min, Max, and Averages are.
    Thanks for any help!
    Tim

    Same here, bump!

  • LMS 4.2 Change Audit Report

    Hi,
    The audit/compliance department at one of costumer wants to see the weekly config change audit report.
    I have done  many test with this feature and i found two problems:
    1. The given report path is empty. Only the directories  was made and there are not report files.
    2. I can not send the report in attachment. How can i publish it automatically? Many reports have attachment option. It has not.
    The immediately option is working  but it does not make report. ( like .pdf )
    How can i send audit change report autmatically to external costumer?
    Regards,

    Hi,
    Sorry for late answer!
    I did not config report path, i use the default path! ( i have tried another path setting also )
    The screens  show the following.
    1, job info
    2. job report view
    If i use the immediatly options the report is good! Only the scheduled job does not make report!
    Regards,

  • LMS 4.2 IPSLA PDF report change date format

           Hi,
    we have a couple of IPSLA reports scheduled which generate PDF files.
    In the header of the PDF file there are "Collerctor Information" field with source name, target name etc. and Start Date/ End Date
    The format of this date is YYYY-MM-DD . Can i change this to DD-MM-YYYY?
    Thank you.

    Hi,
    Sorry for late answer!
    I did not config report path, i use the default path! ( i have tried another path setting also )
    The screens  show the following.
    1, job info
    2. job report view
    If i use the immediatly options the report is good! Only the scheduled job does not make report!
    Regards,

  • LMS 4.2 Syslog PDF Report problem

    Hi,
    when I generate a Syslog 24 hour report and export the result to pdf the font size of the pdf is much too big so I get one page per line.
    The same thing happens when I send the report via email attachment (pdf).
    So the reports are not usable.
    Can I change the settings? (fontsize?)
    Other pdf-reports are ok, e.g. inventory etc.
    regards
    Notker          

    Hi,
    when I generate a Syslog 24 hour report and export the result to pdf the font size of the pdf is much too big so I get one page per line.
    The same thing happens when I send the report via email attachment (pdf).
    So the reports are not usable.
    Can I change the settings? (fontsize?)
    Other pdf-reports are ok, e.g. inventory etc.
    regards
    Notker          

  • CiscoWorks LMS 3.2 EoS/EoL Report fails

    I started a RME Inventory EoS/EoL Hardware Report on devices and got the appended error log. Cisco.com and proxy authentications seem to work well.
    Any idea how to solve this problem?
    Thanks
    Wolfgang

    this could be due to bug CSCte71764. A patch is available on CCO:
    windows:
    http://www.cisco.com/cisco/software/release.html?mdfid=282635175&flowid=5145&os=Windows&softwareid=280775123&release=4.3.1&rellifecycle=&relind=AVAILABLE&reltype=latest
    solaris:
    http://www.cisco.com/cisco/software/release.html?mdfid=282635175&flowid=5145&os=Solaris&softwareid=280775123&release=4.3.1&rellifecycle=&relind=AVAILABLE&reltype=latest

Maybe you are looking for

  • Mini dvi to hdmi, tv not displaying imac screen it remains black

    just brought brand new mini dvi to hdmi adapter.... when i plug in the accessories the imac recognises the hdtv but the tv screen remains black? HELP   Chipset Model:          ATI Radeon HD 2600 Pro   Type:          GPU   Bus:          PCIe   PCIe La

  • One file to multiple printers?

    hi, i did post this question earlier in the Printing and Faxing area, but they suggested i post it here.. maybe someone can help me.. my post was this: ((hi, im just wondering if i can print an Indesign file normaly and set a way to make this file go

  • ITunes account from Serbia

    Hello, This is my first post here, so I would like to offer everyone my greetings and basically say hi, and thank you to Apple and its founders Steve and Woz. Since I live in country were even God said goodbye one day and left, leaving the light on,

  • How to link Purchase Order using account assignment category "F"* to asset

    Hello, I'd like to know how to link Purchase Order, using account assignment category "F" to asset . When I enter asset no. in my ANEK table, po no(ebeln) and po item(ebelp) field is blank. whether every line item in a Purchase order have differrent

  • Problem with filepath

    i'm trying to specify a the filepath but when i declare String path = "C:\abc\def" the compiler complains about an illegal escape character i think it's because of the backslash \ but i don't understand why it should do this. can anyone explain??? th