LMS 4.1 Los equipos 6500 y Nexus 7k aparecen unreacheble en Discovery

Buenas tardes,
Llevo días configurando un LMS 4.1 pero tengo 2 problemas principales.
Tengo equipos 6500 y Nexus 7k que al realizar el Discovery siempre aparecen "unreachable", a pesar de que al revisar el SNMP, telnel, ssh estos estan bien y además se recogen sus traps y configuraciones.
El otro problema es que tengo equipos 3600 que manejan VRF y la looback de snmp esta en VRF, el quipo es descubierto por el Discovery pero lo realiza por otra IP de otra VRF y luego si manda sus traps por la ip de la loopback adecuada.
Ya he aumentado los atributos del timeout snmp a 10
Alguien podría ayudarme?

Similar Messages

  • Como autorizo nuevos equipos, ya tengo 5 autorizados, pero no tengo los equipos, necesito autorizar nuevos

    alguien que me informe por favor como puedo autorizar un nuevo equipo, ya tengo 5 autorizados, quiero desautorizarlos, pero ya no tengo los equipos, quiero autorizar uno nuevo........

    Hola Adrian. Yo estoy con una situación muy similar a la tuya. La diferencia es que en vez de ser una VPN en el extremo de fuera es una punto a punto.
    Misma situación, tengo unas cuantas redes dentro de la red 10.0.0.0/8 que me coinciden con otras iguales de otro cliente. Por lo que quiero natear el destino para cambiar por ejmeplo todo lo que vaya a la red 10.115.1.0/24 por la 10.215.1.0/24.
    Por ahora no lo he conseguido realizar, hice igual que tu, configurar la ACL para permitir el tráfico y posteriormente el NAT haciendo referencia a la ACL pero sin resultado.
    ¿Conseguiste avanzar sobre este tema?
    Muchas gracias de antemano

  • Tengo un imac y un ipad, pero no me sincroniza calendarios sino cuando creo los eventos en el ipad, si los creo en el imac no aparecen en el ipad

    Tengo un imac y un ipad, pero no me sincroniza calendarios sino cuando creo los eventos en el ipad, si los creo en el imac no aparecen en el ipad

    You will do better if you ask your question in the correct forum.
    Try here:
    https://discussions.apple.com/community/ipad/using_ipad
    Good luck,
    x

  • LMS 3.2: RME failed archive with Nexus 5010

    Hi,
    LMS 3.2, RME 4.3.1, dev packages updated, Windows.
    We would like to archive the configuration of the Nexus 5010 switches. Due to authentication with Radius based on tokens we're not able to use telnet/SSH and therefore we only can use SNMP WRite in combination with TFTP.  But, this is not working at all. Other systems like 3750 works fine. Is there a difference between Catalysts IOS and nexus NXOS?
    I searched the forum and found this:
    https://supportforums.cisco.com/message/663481#663481
    upgrade to LMS 2.6, archive config not working anymore
    We ship and start a TFTP server by default on Windows.  You must have an SNMP read-write community string configured on your devices, and entered in DCR for TFTP config fetches to work.  Additionally, udp/69 must be open between device and server.
    The easiest way to troubleshoot this kind of problem is to start a sniffer trace on the LMS server (using Device Center > Packet Capture).  Filter on all traffic to one of the failing devices.  Then, run a Sync Archive job for that same device.  When it fails, the sniffer trace will indicate what the problem is
    Regards
    Ad Olsthoorn

    Hi Lavramov,
    Yes I'm quite sure, I installed the required packages acoording to the Nexus.RME431.v2-2.readme.pdf manual. the manual tell me to install the following (see also attachement).
    To install the Cisco Nexus Series Package, you must install the following dependent packages:
    - SharedDcmaSS.RME431.v2-2.zip
    - SharedInventoryMDS.RME431.v1-5-1.zip
    - SharedSwimMDS9000.RME431.v1-6-1.zip
    - SharedNetshowSS.RME431.v1-1.zip
    regards
    Ad

  • LMS 4.2.2 Interface utilisation on Nexus 7000

    Hi All,
    I'm trying to poll some interfaces for their utilization on a nexus 7000 through LMS 4.2.2.
    When I create a poller fot the specific instances, the LMS recognises the instances, but after activating the poller I get the error "No Such Instance - The specified instance is not available".
    No info is displayed when I generate an interface utilization report for the specific nexus.
    When I activate the automonitor for interface utilization, the interfaces on the nexus are polled.
    On the cisco website there are some features listed which LMS does not support on the Nexus 7000, but polling is not in that list (neither in the supported feature list).
    Any tips?
    Thanks for your help.
    Joris

    Any Idea..??

  • Connection 10 gig between 6500 and Nexus 7009

    I am not able to get link between a 10 gig interface with a 10gbase-lrm on a nexus 7k trying to connect to a 6500 with a 10 gig 10gbase-lx4 interface. I was told this would work. Anyone know if the interfaces are compatable. If not what interface do i need to get for the nexus 7k box.
    Thank You.                   

    Please check mentioned links. I hope it will help.
    http://www.cisco.com/en/US/prod/collateral/modules/ps2797/ps5138/product_data_sheet09186a008007cd00.pd
    http://www.cisco.com/en/US/prod/collateral/modules/ps5455/eol_c51_599855.html

  • LMS 4.2.3: Catalyst 6500 with SUP-2T is invisible in Inventory

    Catalyst 6506 with SUP-2T (s2t54-advipservicesk9-mz.SPA.151-1.SY1.bin) was discovered by LMS, but he is invisible in Inventory. I see this switch on Topology and Cisco View is working fine, but I never seen him in Hardware Summary Tab for example. How to fix this problem ?

    That's odd.
    I'd imagine your system package updates are current given that you're on 4.2.3. Just in case, you would check via Admin > System > Software Center >Device Update. Check the Inventory Config And Image Management check box, and click Check for Updates.
    Once that's confirmed, please let us know does it show up at all in the DCR Inventory? (Reference) If not, what if you add it manually there?

  • Simple Cisco 6500 and nexus 7k, 5k, MDS icons

    Hi Guys,
    I've been searching around for download but still can't find these icons. Do you know where i can download these icons (attachment)? Thanks.

    Hi,
    Try this:
    http://www.cisco.com/en/US/products/hw/prod_cat_visios.html
    HTH

  • 6500 migration to nexus 7k

    Hello,
    I need help with CLNS in NX-OS. I am channging 6500 for Nexus 7K, i have a problem with CLNS.
    I have in IOS this configuration:
    interface Tunnel9999
    no ip address
    ip broadcast-address 0.0.0.0
    tunnel source Vlan402
    tunnel destination 10.130.68.1
    tunnel mode eon
    clns router isis
    isis hello-multiplier 15
    isis hello-interval 1
    router isis
    net 39.724f.3000.001a.0000.0000.1013.1013.2000.0000.00
    interface Vlan402
    ip address 10.40.2.2 255.255.255.0
    no ip redirects
    ip pim sparse-dense-mode
    ip ospf cost 4
    standby ip 10.40.2.1
    standby timers 1 3
    standby priority 120
    standby preempt
    standby authentication airtel
    clns router isis
    I need to set that ocnfiguration in NX-OS but I read there isn´t CLNS in NX-OS, only ISIS IP be able to set in NXOS.is it true?, someone know what is the soluttion?
    Thanks everebody

      Just make sure the priority is lower on the 6500 .  Do you have a vpc between your 6500 and the 7K's ?    We are in the same boat , we have 2 6500's connected to 2 7k's  and most of the routing is stil being done on the 6500's as we haven't had the time to migrate the routing to the 7k's because the customer never gives any downtime and quite frankly moving all that scares the heck out of me .  :-) 

  • Para dar autorizacion a otros equipos cuando ya pase de los 5 equipos permitidos

    Como puedo  dar autorizacion a otro equipo o bien borrar mis equipos autorizados para poder soncronizar mi equipo cuando ya pase de los permitodos me dice que hasta fin de año lo puedo hacer dar de baja esos equipos pero no se que hacer

    En iTunes en tu computadora tendras que Desautorizar todos los equipos Autorizados.
    iTunes Store: Acerca de las autorizaciones
    http://support.apple.com/kb/HT1420?viewlocale=es_ES
    Lee la seccion:
    Para retirar las autorizaciones a todos los ordenadores asociados a tu ID de Apple

  • Catalyst 6500 - Nexus 7000 migration

    Hello,
    I'm planning a platform migration from Catalyst 6500 til Nexus 7000. The old network consists of two pairs of 6500's as serverdistribution, configured with HSRPv1 as FHRP, rapid-pvst and ospf as IGP. Futhermore, the Cat6500 utilize mpls/l3vpn with BGP for 2/3 of the vlans. Otherwise, the topology is quite standard, with a number of 6500 and CBS3020/3120 as serveraccess.
    In preparing for the migration, VTP will be discontinued and vlans have been manually "copied" from the 6500 to the N7K's. Bridge assurance is enabled downstream toward the new N55K access-switches, but toward the 6500, the upcoming etherchannels will run in "normal" mode, trying to avoid any problems with BA this way. For now, only L2 will be utilized on the N7K, as we're avaiting the 5.2 release, which includes mpls/l3vpn. But all servers/blade switches will be migrated prior to that.
    The questions arise, when migrating Layer3 functionality, incl. hsrp. As per my understanding, hsrp in nxos has been modified slightly to better align with the vPC feature and to avoid sub-optimal forwarding across the vPC peerlink. But that aside, is there anything that would complicate a "sliding" FHRP migration? I'm thinking of configuring SVI's on the N7K's, configuring them with unused ip's and assign the same virtual ip, only decrementing the prio to a value below the current standby-router. Also spanning-tree prio will, if necessary, be modified to better align with hsrp.
    From a routing perspective, I'm thinking of configuring ospf/bgp etc. similar to that of the 6500's, only tweaking the metrics (cost, localpref etc) to constrain forwarding on the 6500's and subsequently migrate both routing and FHRP at the same time. Maybe not in a big bang style, but stepwise. Is there anything in particular one should be aware of when doing this? At present, for me this seems like a valid approach, but maybe someone has experience with this (good/bad), so I'm hoping someone has some insight they would like to share.
    Topology drawing is attached.
    Thanks
    /Ulrich

    In a normal scenario, yes. But not in vPC. HSRP is a bit different in the vPC environment. Even though the SVI is not the HSRP primary, it will still forward traffic. Please see the below white paper.
    http://www.cisco.com/en/US/prod/collateral/switches/ps9441/ps9402/white_paper_c11-516396.html
    I will suggest you to set up the SVIs on the N7K but leave them in the down state. Until you are ready to use the N7K as the gateway for the SVIs, shut down the SVIs on the C6K one at a time and turn up the N7K SVIs. When I said "you are ready", it means the spanning-tree root is at the N7K along with all the L3 northbound links (toward the core).
    I had a customer who did the same thing that you are trying to do - to avoid down time. However, out of the 50+ SVIs, we've had 1 SVI that HSRP would not establish between C6K and N7K, we ended up moving everything to the N7K on a fly during of the migration. Yes, they were down for about 30 sec - 1 min for each SVI but it is less painful and waste less time because we don't need to figure out what is wrong or any NXOS bugs.
    HTH,
    jerry

  • LMS + Nexus F2 linecards

    I'm wondering if anyone else is using LMS 4.2 with the F2 series Nexus 7K linecards (N7K-F248XP-25).
    I'm trying to but they show up as "Unsupported Card" in CiscoView (despite having the latest 7.1 version of the CiscoView Nexus 7K package).
    At this point I'm not sure if it's a CiscoView- or VDC-related issue but I'm leaning towards the former.

    You should be able to manage those cards in CiscoView once you update the CV package for the Nexus 7k to version 8.0. (Youll lneed the latest SwitchAddlets also.)
    Per the package release notes:
    WHAT IS NEW?
    ============
    This 8.0 release of the Nexus7000 device package provides support for the following devices and modules:
    Modules supported in this release
    *  N7K-F248XP-25

  • LMS 4.0, Support for Nexus VDC

    Hi everybody,
    Does LMS 4.0 support the management of Nexus 7000 VDCs?
    I don't need it do be able to do anything complex. I was just interested in syslog, polling, and config fetches. I can poll and ping the management IPs of the VDCs from the command line of the server itself, but it stays questioned and "UNKNOWN" in the device list.
    The admin context of the Nexus 7000s are being added just fine. We recently built 4.0, coming from LMS 2.6. LMS 2.6 appears to add the VDC to the DCR without issue, but 4.0 does not. I just want to make sure that I'm not missing something.
    Thanks for the help!
    Tim

    Hi everybody,
    Does LMS 4.0 support the management of Nexus 7000 VDCs?
    I don't need it do be able to do anything complex. I was just interested in syslog, polling, and config fetches. I can poll and ping the management IPs of the VDCs from the command line of the server itself, but it stays questioned and "UNKNOWN" in the device list.
    The admin context of the Nexus 7000s are being added just fine. We recently built 4.0, coming from LMS 2.6. LMS 2.6 appears to add the VDC to the DCR without issue, but 4.0 does not. I just want to make sure that I'm not missing something.
    Thanks for the help!
    Tim

  • No puedo activar los programas asociados a mi cuenta del trabajo

    Hola a todos/as,
    Tengo un problema con los programas que tengo instalados en mi PC del trabajo, mi empresa compró licencias para todo el equipo pero salvo otro compañero y yo que tenemos PC de torre el resto tiene portátiles.
    Trabajamos en las instalaciones del cliente el cual tiene aplicada una maqueta al sistema operativo por el cual no se permite el acceso a ciertas páginas, imposibilidad de instalar aplicaciones y demás problemas asociados al no ser administradores de los equipos.
    Mi empresa compró las licencias a principios de año ya que el cliente migraba el sistema operativo a uno más actual pero no se tuvo en cuenta que los que teníamos las torres no se nos migraba el sistema operativo hasta hace un mes. Ahora mismo todos tenemos instalados los programas CS6 pero solo los que trabajan con portátiles tienen los programas registrados y los que tenemos torre no. Me temo que Adobe da un tiempo máximo para activar las licencias de los programas ya que no tengo manera de activarlos.
    Agradecería que me ayudaseis con este problema.
    Muchas gracias y un saludo.
    Antonio.

    las licencias no caducan, pero necesitas al administrador para que te de permiso.

  • No se me actualiza los datos de pago

    A LO QUE ME PIDE QUE ACTUALIZE MIS DATOS DE PAGO YO INGRESO TODOS MIS DATOS HE INTANTADO VARIAS VECES Y CON ALGUNAS TARJETAS DE CREDITO HASTA CON UNAS QUE YA HE OCUPADO ANTERIORMENTE Y ME HA IDO DE MARAVILLA PERO AHORA SOLO ME SALE Q CONSULTE CON EL SOPORTE TECNICO DE ITUNES YA NOSE QUE MAS HACER Y NO PUEDO ACT NINGUNA DE MIS APLICACIONES DEBIDO A ESTO AYUDENMEEE PORFAVOOOOR!!!!!!!!

    Teniendo SAP cerrado, elimina la carpeta %temp%SM_OBS_DLL por completo en cualquier de los equipos. Entra a SAP nuevamente en ese equipo e intenta visualizar alguno de los informes de crystal.
    Otra cosa que puedes intentar es crear un ODBC al servidor desde cada equipo de usuario.
    Por último, lo que se me ocurre es que abras alguno de los informes en el diseñador de Crystal y actualices la conexión de base de datos (sección Explorador de objectos) y de cada tabla haciendo uso de una conexión SAP Business One (lo verás en el wizard de conexión a base de datos).

Maybe you are looking for