LMS 4.1 Topology fail

I have HQ and Branch router
HQ       = 2811
Branch = 2801
Connection type Freme-relay between HQ and Branch
CDP enable on interface
The Branch router show in UNCONNECTED DEVICE VIEW of Topology
please solve this problem
Thanks

At HQ router show cdp can not see Branch router
At Branch router show cdp can not see HQ router
configure router
======================================
HQ
interface GigabitEthernet0/1.1000
bandwidth 512
encapsulation dot1Q 1000
ip address 10.10.191.13 255.255.255.252
======================================
Branch
interface Serial0/2/0.1 point-to-point
bandwidth 512
ip address 10.10.191.14 255.255.255.252
frame-relay interface-dlci 16 IET
=====================================
Thanks

Similar Messages

  • LMS 4.2 Topology Data Collection Issue

    Hi there,
    i have an issue with the lms 4.2 Topology Data Collection. After installation the Topology Data Collection was running normaly, but since first server reload the Topo Data Collect under Inventory > Dashboards > Device Status > Collection Summary is "frozen". It only shows the following content from first run:
    Topology Data Collection    193    0    Not Available     Running    Schedule
    Is there any option to stop this process elsewhere? I cannot find anything under jobs in running state or so. Clicking on Schedule only give me the option to start data collection, but lms always returns that the process is running.
    Thanks for help.

    Hi,
    i have reseted the ANI db using NMSROOT\bin\perl.exe NMSROOT\bin\dbRestoreOrig.pl dsn=ani dmprefix=ANI
    Everything is set to 0:
    Topology Data Collection      0 0 Not Available                          Running Schedule
    UT Major Acquisition            0 (0 End hosts 0 IP Phones) 0      Not Available Idle Schedule
    VRF Collection                    0 0                                              Not Available Idle Schedule
    But Topology Data Collection is still frozen to "Running" state....

  • LMS 4.0.1 fails on updating switch sw (3750ME, 2960S)

    Hi,
    Newly installed LMS 4.0.1 fails when upgrading switch software. From sw distribution job logs, it looks like that LMS does not recognize switch properly. This happens with 3750 Metro and 2960S switches (at least those I've tested).
    Attached file contains full job logs in zipped format.

    After looking into swim debug file, found this error:
    [ Fri May 20  14:27:38 EEST 2011 ],ERROR,[RFRDOper:172.31.57.11],com.cisco.nm.xms.xdi.pkgs.LibSwim.common.Utility,loadProperties,545,Exception while reading the prop file java.io.FileNotFoundException: G:\PROGRA~2\CSCOpx\MDC\tomcat\webapps\rme\WEB-INF\lib\pkgs\..\..\conf\swim\StackFlashes.properties (The system cannot find the file specified)
    Could this be related to problem? Should I reinstall LMS or can this file (StackFlashes.properties) be copied from another installation???
    /Mikko

  • LMS 4.2 topology map & explorer 8

    Hi!
    The LMS 4.2 topology map could not start with IE8 on Windows XP client. But it is working well with Mozilla!
    The java install was success!
    We get the following messages!
    and
    Any idea?
    Regards,

    Hi,
    May be is independed of the browser but if i started under IE it was unsuccessfull.
    I cleared the java from my computer and opened the LMS by IE. The java was intalled but topology map did not started.

  • LMS 4.1 topology services

    Our LMS cannot start topology services.
    we got the following error:
    Cannot connect to ANIServer: ANIServer7.0-lms
    Probable Cause
    1. Unknwown Hostname
    2. Unknown Error
    Recommended Action
    1. Check if the Hostname is DNS resolvable
    2. Check whether the ANIServer process is up and running.
    Where & how can i fix this problem. I dont know where to find ANIServer.
    Please advice

    1. Has it ever worked? If yes, has anything changed? If no, then your installation may be suspect.
    2. Do you get the same error when you are at the server itself (as opposed to accessing LMS remotely via a browser)? If yes, then the ANIServer process is likely not running. Look here for instructions on how to perform server self test and restart processes.
    3. If the problem is limitied to client acess, I'm assuming you've checked suggestion #1 in your post. Beyond that, I have seen a similar issue when Java is not running the exact version (1.6.0_24) recommended by the LMS. I've also seen a clear of the Java cache remedy this issue.
    Hope this helps.

  • LMS 4.2 Backup Failing Randomly

    Has anyone seen this?
    Backup failed on 2012/06/03 at 22:02:52. REASON: Unable to proceed with the backup operation as some files are being accessed by jobs. Reschedule the jobs such that the backup job does not coincide with other jobs.
    Randomly the backup for lms 4.2 is failing. it has suceeded but majority of the time its failing. i have tried changing times but nothing seems to work.  previously we were running 4.0.1 and had noproblems with the backup time.
    Just found the bug
    CSCtz29665
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2.1/readme/lms_421_readme.html#wp1203775
    no work around at the moment

    the patch for BugID CSCtz29665 is released here on CCO:
    "http://www.cisco.com/cisco/software/release.html?mdfid=284259296&flowid=31102&softwareid=280775103&os=Windows%20CE%202.11&release=CSCtz29665_4.2.2&relind=AVAILABLE&rellifecycle=&reltype=latest"
    I do not know whey they opend a new section for Windows CE 2.11, - but on CCO you have to follow this path to find it:
    Downloads Home > Products > Network Management and Automation > Routing and Switching Management > Network Management Solutions > Cisco Prime LAN Management Solution > Cisco Prime LAN Management Solution 4.2 > LMS Patches > Windows CE 2.11-CSCtz29665_4.2.2

  • Adobe Presenter Always Passes Complete Status to LMS - Even When Quiz Failed

    Issue:
    I'm trying to publish an Adobe Presenter 7 course with a quiz using SCORM 1.2. I am publishing to our LMS (Cornerstone OnDemand). The course loads and plays fine. However it always reports a complete status to the LMS - even when I fail the quiz. I can even see the score (10 out of 50 points), but the status still shows as completed when it should be incomplete. The pass threshhold is set to 50 points...and yet any scoring allows a completed status.
    Questions:
    1. Has anyone used Presenter with CSOD?
    2. Has anyone used Presenter with any SaaS LMS?
    3. Which settings are required to acurately reports a status?
    Thanks,
    Dan

    On top of Ravi's suggestion, what I would also recommend is checking the "scorm_support.js" file which can be found in your Scorm Support folder---this is automatically created when you publish your PPT deck.
    Open the scorm_support.js file using Notepad, Notepad++....anything other than Word.  From there, look at the top of the js file and you'll see a few variables which help to establish the SCORM setting of the training, but the one to look for looks like this:
    var g_nAPI = 1;
    if that variable is set to "0", then your published content will trigger SCORM 2004, not 1.2.
    I've seen this come up on a few occasions, but ever since upgrading my version of Presenter to 7.0.5, this has gone away.
    Additionally, there are a few other things you can do which might help in terms of deploying content in your LMS:
    1. I would strongly recommend downloading the ADL SCORM 1.2.7 test suite.  What this basically does is allow you to test the conformity of the SCORM package of a published Presenter course to determine if problems exist BEFORE you post your files to an LMS.  You can download the test suite here:
    http://www.adlnet.gov/adlnews/Documents/News%20Archive/TheSCORMConformanceTestSuiteVersion 127SelfTestisAvailableforDownload.aspx
    2. If you have an LMS admin at your disposal, be sure to check with that person for deployment criteria when your content is installed on the LMS.  If YOU are that person, then you have some homework to do--because you're going to need to know how to run installation procedures and content checks on your training as recommended by the LMS software.
    I've developed and deployed Presenter content on a variety of LMSs, and some have nastier quirks than others...so one solution may not fit every environment, but you have to keep checking!  I would also try reaching out to your LMS's tech support if possible.
    Rob
    http://www.robrode.com/yabb/

  • LMS 3.0 topology services and email notifications issue

    Hi
    I have an LMS 3.0 install that was working when I installed it at a customer site a few months back.  I went back in to give them an overview of its operation and there are now several issues.  Nothing has changed since I installed it because the customer didn't know how to use it.
    The issues now are
    1.  When there is a link failure the mail account that should receive a notifivation gets nothing.
    2. In topology services the faled link goes red but when repaired goes to dotted red and never goes back to solid black.
    I know the mailing worked previously because I can see previous errors that were fixed being reported about a month back.
    Also in DFM all my devices now show as learning under the device discovery page and never move from 10% completed.  I found another post that says I need to upgrade to LMS 3.0.1 and DFM 3.0.5
    Is it possible this will fix the other issues ?
    I have LMS 3.0, DFM 3.0.0, RME 4.1 and CM 5.0
    Many thanks, Stephen.

    Yes, your versions are plagued by numerous bugs.  It is highly recommended you upgrade to LMS 3.0.1, then apply the Campus Manager 5.0.6 and DFM 3.0.5 service packs.  LMS 3.0.1 can be downloaded from http://www.cisco.com/cgi-bin/tablebuild.pl/lms301 , and the various required SPs from Common Services > Software Center > Software Update.

  • LMS 3.2 Backup Failed

    Hi, i try to backup lms but it always give me errors,i did it 2 times one with GUI from common services and the other one using command, the output is
    2 errors reported
    [Sun May  8 18:20:36 2011] Validation D:/LMS-BackUp/May-2011/0\0\campus\database\ani.db failed.
    [Sun May  8 18:20:36 2011] Validation D:/LMS-BackUp/May-2011/0\0\campus\database\ani.db failed.
    [Sun May  8 18:20:36 2011]  ERROR(1403): Database aniDb backup failed and . Check the log file for information.
    [Sun May  8 18:20:36 2011]  Backup failed: 2011/05/08 18:20:46
    Primary key for "EmbuUserTracking" has missing index entriesSQL error (-300) -- Run time SQL error -- Validation of table "EmbuUserTracking" has failed
    VALIDATE TABLE "cwsiSA"."HistoryHostTracking"
    Index "historyupdate" has invalid or duplicate index entries
    Index "historyupdate" has missing index entries
    SQL error (-300) -- Run time SQL error -- Validation of table "HistoryHostTracking" has failed
    VALIDATE TABLE "cwsiSA"."HistoryUserTracking"
    2 errors reported
    [Sun May  8 18:19:20 2011] Validation D:/LMS-BackUp/May-2011/0\0\campus\database\ani.db failed.
    SQL Anywhere Command File Hiding Utility Version 10.0.1.3830
    SQL Anywhere Backup Utility Version 10.0.1.3830
    (41672 of 41670 pages, 100% complete)
    Database backup completed
    SQL Anywhere Command File Hiding Utility Version 10.0.1.3830
    SQL Anywhere Validation Utility Version 10.0.1.3830
    2 errors reported
    SQL error (-300) -- Run time SQL error -- Validation of table "EmbuUserTracking" has failed
    SQL error (-300) -- Run time SQL error -- Validation of table "HistoryHostTracking" has failed
    [Sun May 8 09:23:22 2011] Validation D:/LMS-BackUp/May-2011\0\campus\database\ani.db failed.
    [Sun May 8 09:23:22 2011] Validation D:/LMS-BackUp/May-2011\0\campus\database\ani.db failed.
    [Sun May 8 09:23:22 2011] ERROR(1403): Database aniDb backup failed and . Check the log file for information.
    [Sun May 8 09:23:22 2011] Backup failed: 2011/05/08 09:23:32
    I have checked the directory and the size of data is aroung 15 GB is this correct backup
    thanks for your help

    Hi Joseph,
    I run the perl.exe from C:\Program Files\CSCOpx\bin and then i write the command
    C:\Program Files\CSCOpx\objects\db\conf\configureDb.pl action=validate dsn=cmf
    I got the below result, i am new perl script and i i dont know what i did wrong
    Backslash found where operator expected at - line 1, near "CSCOpx\"
    Backslash found where operator expected at - line 1, near "objects\"
    Backslash found where operator expected at - line 1, near "db\"
    Backslash found where operator expected at - line 1, near "conf\"
    thanks for your help and support

  • LMS 3.2: RME failed archive with Nexus 5010

    Hi,
    LMS 3.2, RME 4.3.1, dev packages updated, Windows.
    We would like to archive the configuration of the Nexus 5010 switches. Due to authentication with Radius based on tokens we're not able to use telnet/SSH and therefore we only can use SNMP WRite in combination with TFTP.  But, this is not working at all. Other systems like 3750 works fine. Is there a difference between Catalysts IOS and nexus NXOS?
    I searched the forum and found this:
    https://supportforums.cisco.com/message/663481#663481
    upgrade to LMS 2.6, archive config not working anymore
    We ship and start a TFTP server by default on Windows.  You must have an SNMP read-write community string configured on your devices, and entered in DCR for TFTP config fetches to work.  Additionally, udp/69 must be open between device and server.
    The easiest way to troubleshoot this kind of problem is to start a sniffer trace on the LMS server (using Device Center > Packet Capture).  Filter on all traffic to one of the failing devices.  Then, run a Sync Archive job for that same device.  When it fails, the sniffer trace will indicate what the problem is
    Regards
    Ad Olsthoorn

    Hi Lavramov,
    Yes I'm quite sure, I installed the required packages acoording to the Nexus.RME431.v2-2.readme.pdf manual. the manual tell me to install the following (see also attachement).
    To install the Cisco Nexus Series Package, you must install the following dependent packages:
    - SharedDcmaSS.RME431.v2-2.zip
    - SharedInventoryMDS.RME431.v1-5-1.zip
    - SharedSwimMDS9000.RME431.v1-6-1.zip
    - SharedNetshowSS.RME431.v1-1.zip
    regards
    Ad

  • LMS 4.2.3: Failed to fetch vlan.dat

    Hello
    We are running LMS 4.2.3 on a softappliance. Config fetch works fine. Protocol order is ssh and scp. VLAN fetch we configured the protocol order to SCP and TFTP. When trying sync archive i see the follwing error message:                    
    Status: Partially Successful
    VLAN
    Insufficient no.
    SCP failed: Insufficient no. of interactive responses (or timeout)  for command copy flash vlan.dat scp:.
    SCP from CLI works fine with the command:
    copy flash:vlan.dat scp:
    Does anybody have the same problem?
    Any ideas?
    Regards,
    Martin

    Make sure you have configured the SCP credentils in LMS under :
    Admin > System > System Preferences.
    For more details check :
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/user/guide/admin/server.html#wp1168063
    -Thanks

  • LMS 4.2 Topology View

    Hi
    I have installed LMS 4.2 in one of my customer site. We have added all the switches and everything works perfectly. Recently we added all the CCTV cameras in lms.
    Issue is that when CCTV camera is down  it takes a long time to show in topology map..Any one knows how to make  view in topology map as real time. Atleast a delay of 30sec is okay..
    Regadrs
    -Danish

    Topology view is not really intended to be a real time (or near real time) fault management tool. While you can turn up the speed of it's discovery cycle, it will create excessive workload and, depending on the size of your network, may result in polling never stopping due the time to complete one cycle being more than the time you have configured to start over again.
    To see near real time faults (such as loss of a CCTV camera), have operators refer to the Fault Monitor display:
    http://www.cisco.com/en/US/customer/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/user/guide/lms_monitor/mnt-faultbrowser.html
    If you want to customize the polling of devices for fault management, refer to the Fault Management chapter of that same guide:
    http://www.cisco.com/en/US/customer/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/user/guide/lms_monitor/mnt-fault.html

  • LMS 4.1 Topology Service Question

    i have only 1 switch 2960 POE at customer enviroment.
    i did run topology service and checked on the right side POE CAPABLE Devices
    it shows me that i have 4 switch POE while actually there is only 1 switch POE in real enviroment.
    does anyone have any idea about this issue ?
    appreciate soonest reply
    Thanks

    Its hard to tell without getting the info requested but check the DCR to see how its identified as which device type it is. And compare that to the inventory hardware report and the actual device itself. 
    1. Check the DCR to verify the correct device type is defined for the incorrectly reported devices.
    2. Were the devices automatically discovered or added manually to LMS?
    3. Re-run a a data collection:
    http://www.cisco.com/en/US/partner/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/user/guide/monitoring_troubleshooting/mnt-topo.html#wp1044599
    Post the ani.log and the show ver requested after data collection completes.

  • LMS 4.0.1 fails to download SW and device updates

    Hi All,
    I have a problem downloading software and device updates for LMS 4.0.1.
    In the psu.log I get the following:
    [ Mon Nov 26 12:51:51 CET 2012 ] INFO   [SwUpdateAction : getUpdatesFromCCO]  : Validated Cisco.com credentials..
    [ Mon Nov 26 12:51:51 CET 2012 ] INFO   [SecurityHandler : getCSProxyHost]  : No proxy Host configured
    [ Mon Nov 26 12:51:51 CET 2012 ] INFO   [SecurityHandler : getCSProxyPort]  : No proxy port confgured
    [ Mon Nov 26 12:51:51 CET 2012 ] ERROR  [CcoDownloadAdapter : getXmlFileList]  : failed to connect to Cisco.com:RespCode=404, RespMsg=Not Found
    [ Mon Nov 26 12:51:51 CET 2012 ] ERROR  [RemoteRepSync : downloadPsuHeadersAsXml]  : VDSException thrown com.cisco.nm.xms.vds.VDSException: CcoDownloadAdapter::getfileList():failed to connect to Cisco.com
    Hope someone can help.
    Thanks.
    Rgds,
    Jesper

    Hi Jesper,
    Download the Patch for thsi Bug CSCto46927. (lms40x-win-CSCto46927-0.zip ) for windows
    lms40x-sol-CSCto46927-0.zip  (solaris)
    I hope this will fix the issue
    Thanks
    Afroz

  • Problems with LMS 4.1 Topology Maps

    Hi
    I've just installed  LMS 4.1 in my demo lab. Everything is working fine except for the Topology maps. When I click on the topolgy from configuration
    I get
    I've tried doing what its asked a number of times but with no success and was wondering if anyone else has had this problem and know the fix.
    I'm running windows 7 with Java version 1.6.0_26 . Also this is the virtal appliance installation of Cisco LMS 4.1.
    Regards

    Your problem looks similar to one I have seen with incompatible Java versions. I suggest two things to check it out:
    1. Launch Topology directly when logging in from the server desktop itself (via RDP is fine). Does it work there? If so, the issue is client-based.
    2. Uninstall Java compeltely on the client. Then launch LMS in a browser. When you navigate to Topology tools you should be redirected to the CiscoWorks server's own Java distribution which is packaged to be the precise version (1.6.0_24) that it prefers. Download and install that version and check if the problem is fixed.
    One can work around the Java issues in some cases but it's ugly. This, combined with Sun / Oracle's predeliction to want to upgrade Java to the latest version automatically makes this one of the trickier tools in the LMS toolbag to use consistently from diverse remote clients.

Maybe you are looking for