LMS 4.2.4 - report check "end host" list

Hi All,
     I have a list of 26 "end host" identify by mac-address. I would like to generate every day a report to check that these devices exist on the network.
     If you can help me about this task? do i have to use "user tracking" ?
     Just for precision ...it is not "network device" but "end host" devices (PCs)
Thanks for your help.
Regards.

Still no explanation from the experts?
Thanks
Lothar

Similar Messages

LMS 4.2.5 - UserTracking Connected End Host Report not useable

Hi all,
trying to understand the different available UserTracking-Reports (Active End Host Report, Dormant End Host, Connected End Host) provided by UserTracking Summary Portlet I struggled with understanding the Connected End Host Report.
In Docs an End Host in status connected is: End hosts that are connected to the network but do not have its MAC address entry in the connected switch CAM table.
Executing this Connected End Hosts Report I'm not able to understand the output:
    User Name MAC Address Host Name IP Address Subnet Status Switch Port VLAN Last Seen
1.             Connected      Fa0/2 AK-ETH23 14 Dec 2014, 05:17:44
2.             Connected      Fa0/13 VLAN0178 14 Dec 2014, 05:17:44
3.             Connected      Gi0/15 inactive400 14 Dec 2014, 05:17:44
4.             Connected      Fa4/13 VLAN0924 14 Dec 2014, 05:17:44
5.             Connected      Gi0/18 inactive400 14 Dec 2014, 05:17:44
With this output nobody is able to correlate anything; simply a port and a vlan is seen, but no endhost-information/switch or switchport information!
As this can be seen on different LMS installations, it seems to be a general issue.
Anybody out the having further information?
Thanks for your valued feedback.
Lothar

Still no explanation from the experts?
Thanks
Lothar

LMS 4.2.4 User Tracking End Host Report The system cannot find the path specified

Hello at all,
I have a problem when creating a scheduled User Tracking End Host Report.
I always get the message "The system cannot find the path specified" and the job fails.
An immediate report is successful.
I tried to change the "Report Publish Path" from "C:/Program Files (x86)/CSCOpx/" to "C:/PROGRA~2/CSCOpx/", but that did'nt worked.
Has anybody an idea?
Regards, Kerstin

Share the screenshot of the following directory :
NMSROOT\CSCOpx\campus\etc\cwsi
In case it is blank, try following :
1.Stop the services : net stop crmdmgtd
2.Take a copy of > C:/Progra~2/campus/etc/users and place it under C:/Progra~2/campus/etc/cwsi
3.Start the services : net start crmdmgtd
Please try and let me know the updates.
-Thanks
Vinod
**Encourage Contributors. RATE them.**

Wireless End Host Report LMS 3.2

We are having LMS 3.2 with Campus Manager 5.2 , I have added our WisM (Wireless Integrated ServiceModule) in the LMS and it shows that the device is reachable , we get inventory , run jobs etc . However when I try to get the End Host Report for this device it shows that no hosts found
I have configured SNMP v2 read only settings on the controller and the LMS
I wanted to know will we get End User Reports from the WiSM / Cisco 4402 controllers. Is there some more config etc need to be done
Regards

Thanks Joe
Will the WLC be supported in any future releases
Regards

LMS 4.0.1 End Host display issue

Using LMS 4.0.1.
When looking at the Device Centre - Troubleshooting view for a device it will display the number of End Hosts in the Configuration Status>Configuration Details section. If I click on the number of devices a pop-up will appear saying "No end hosts found", however if I go to Reports>Inventory>User Tracking and run the report it displays the end hosts correctly
I would appreciate assistance on what could be causing this issue. It was happening with Lms 4.0 but upgrade to 4.0.1 did not change it.

michel.hegeraat wrote:Try to grab the url it gives. Something like:http://didata:1741/cmapps/utEndHostReport.do?action=Submit&crossLaunch=admindashboard&runTypeOption=Immediate&devName=lab-SW23&devIP=10.170.46.250Check if these to guys are correct and resolvabledevNamedevIPCheers,Michel
Below is the url from a sample device (this problem occurs with all I have checked so far) that appears when I click the numeric End Hosts quantity from the Device Center - Troubleshooting page
http://lmsnetmgr:1741/cmapps/utEndHostReport.do?action=Submit&crossLaunch=admindashboard&runTypeOption=Immediate&devName=Gosford NOC Sw 2&devIP=10.76.152.56
When I use the same Device name or Device IP when running a end host query from Reports>User Tracking>Quick reports I get the correct end hosts displayed. The quantity displayed corresponds with the quantity shown on the Device center - troubleshooting page
So - the problem is not related to using an incorrect device IP or Device Name

Lms 4.2 Cannot enable End Host Discovery on Trunk

Hi...
I have noticed that our LMS does not collect any information about wireless users connected to autonomous access points, although I can see the mac address of the wireless users on the switch (2960) Trunk port connecting to the AP via CLI. I can also get the IP address from the core switch. Even after selecting 'Perform Data Collection' on the AP in the topology, the Wireless End hosts report remains blank.
I am trying to enable the option 'End host Discovery on Selected Trunks' in the 'Acquisition configuration in Trunk' menu and after selecting the switch where the AP resides and clicking 'show Trunk' I get the message 'there are no trunks in the device(s) selected', although there are several trunk ports on this switch, other than the one connecting to the AP. The switch and the AP are managed by LMS. We are facing this problem with all Autonomus APs. We do not use WLSE. Is there something missing to discover these Wireless hosts ?
All help is appreciated

Is it safe to set UTGetVlansWithUserPorts=0 in the NMSROOT/campus/etc/cwsi/ut.properties ? I have seen this in a previous discussion, but thath was related to LMS 3.1, not 4.2
Regards

CM End Hosts Report Does not Retain Edited User Data

I have manually edited end host records to add user names and notes in the end host report. Those entries seem to be overwritten whenever the records are rediscovered. Is there a setting which allows the manually entered and saved data to be retained? I am running CM 5.2.2 in LMS 3.2.

IN the layout section Click on Add view--> Advanced--> No Results --> Enter the friendly message you would like to see. This will help achieve your results

End Host IP Address not seen in the UserTracking Report

hi,
After the successful completion of Device Discover (Common Services) and Data Collection (Campus Manager, whenever the end host reports are generated, only the mac address is seen, the ip address and subnet mask fields are blank.
The LMS version is 3.2.1
Campus Manager version : 5.2.2
Ping Sweep is also enabled under the Acquisition settings.

The issue has been resolved. now the IP addresses and the Subnet infomation is displayed in the User Tracking Reports. The problem was, that no Layer 3 device was added in the LMS. as per the document:
ANI reads the ARP table from the Layer 3 devices it discovered to map the MAC addresses to IP addresses. If UserTracker shows the MAC addresses, and the IP address and hostname fields are empty, chances are that ANI does not discover the default gateway of the host correctly.
Added the Layer 3 switches, performed the Data Collection, Device Discovery and UT Acqusition and now the endhost reports are generated based on IP address.
following is the link for reference:
http://www.cisco.com/en/US/products/sw/cscowork/ps563/products_tech_note09186a0080094949.shtml#ts2b

LMS 4.0.1 User Tracking Problem "No end hosts found"

Hi everybody,
I have problems with devices that do not appear in the user tracking utility.
These devices are a cisco WS-C4506-E with Supervisor II-Plus-10GE and two WS-C6509 with Supervisor Engine 720.
When I start acquisition for the devices I receive following message: "Device unreachable". When I try to watch the end hosts, I get following Message: "No end hosts found."
I have patched LMS 4.0.1 with CSCto06189 Patch.
Is there perhaps a solution?
Roman

400 devices - do you mean 400 end users?
Do they all use a Layer 3 default gateway that is among your discovered and managed devices?
Have you followed the steps and troubleshooting from around page 24 of this guide?

LMS 4.1 with CUCM 8.0.2 Phones only detected as End Hosts

Hi,
looks like I still have an issue with LMS to recognize the IP Phones in UT as IP Phones.
SNMP RO on Call Manager is enabled and is green in CM (e.g. topology) - so SNMP get is basically fine.
The Phones are recognised as End Devices in UT.
As far as I understand, now if I start a Phone Aquisition, the CUCM is polled by LMS to gather additional information about the phones.
So it seems there is a problem with the SNMP polling of the Callmanager?
thanks for any help!
br.herwig

Yes, its in DCR
below the device status of the Callmanager:
20.
192.168.2.10
Callmanager
192.168.2.10
1.3.6.1.4.1.9.1.583
Cisco 7825H Media Convergence Server
The phones are collected by UT as end hosts (it is seen through the voice vlan called "UC"):
But this phones are not recognized as phones in UT:
thanks,
br.herwig

LMS 4.2.3 End Host not found

When I go to Troubleshooting Workflows. Select a switch, select View the switch, then scroll to end hosts, it tells me that their is no end hosts found. However if I search for end hosts, it shows the end hosts that are connected to the switch.

Hi Afroj,
the OID (1.3.6.1.2.17.4.3.1.1) not walk
[srvlms/root-ade ~]# snmpwalk -c iptread x.x.x.x.1.3.6.1.2.1.17.4.3.1.1
SNMPv2-SMI::mib-2.17.4.3.1.1 = No Such Object available on this agent at this OID
the OID (1.3.6.1.4.1.9.9.156.1.1.2.1) not walk
[srvlms/root-ade ~]# snmpwalk -c iptread x.x.x.x 1.3.6.1.4.1.9.9.156.1.1.2.1
SNMPv2-SMI::enterprises.9.9.156.1.1.2.1 = No Such Object available on this agent at this OID
and if tape the simply snmpwalk it's ok:
[srvlms/root-ade ~]# snmpwalk -c iptread x.x.x.x
SNMPv2-MIB::sysDescr.0 = STRING: Linux release:2.6.18-194.26.1.el5PAE machine:i686
SNMPv2-MIB::sysObjectID.0 = OID: SNMPv2-SMI::enterprises.9.1.1348
DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (240048448) 27 days, 18:48:04.48
SNMPv2-MIB::sysContact.0 = STRING:
SNMPv2-MIB::sysName.0 = STRING: CCM-FR-SUR-PUB
SNMPv2-MIB::sysLocation.0 = STRING:
SNMPv2-MIB::sysServices.0 = INTEGER: 72
IF-MIB::ifNumber.0 = INTEGER: 3
IF-MIB::ifIndex.1 = INTEGER: 1
IF-MIB::ifIndex.2 = INTEGER: 2
IF-MIB::ifIndex.3 = INTEGER: 3
IF-MIB::ifDescr.1 = STRING: lo
IF-MIB::ifDescr.2 = STRING: eth0
IF-MIB::ifDescr.3 = STRING: sit0
IF-MIB::ifType.1 = INTEGER: softwareLoopback(24)
IF-MIB::ifType.2 = INTEGER: ethernetCsmacd(6)
IF-MIB::ifType.3 = INTEGER: tunnel(131)$
mumm strange

Setting apache as a front end host-proxy web server for weblogic 10.3.3

Hi ,
i have installed apache 2.2.21 in the red hat linux 6 environment.Now i am trying to set that apache web server as a front end host ,proxy web server for my weblogic 10.3 application server cluster. My apache is listening to the port 8080.
What changes i had to made in admin console of my server as well as in the httpd.conf file of apache.
Can any one guide me how to proceed ?
Any help is highly appreciated......

Thanks Ravi,
i have already gone through http://docs.oracle.com/cd/E12840_01/wls/docs103/plugins/apache.html.
In my case "mod_wl_22.so" was not available but i downloaded this p10051826_1033_Generic.zip file from where i got that file and make it available in the modules directory, changed the file permissions (using chmod 755 mod_wl_22.so) and also changed the httpd.conf file as below :
LoadModule weblogic_module modules/mod_wl_22.so
<IfModule mod_weblogic.c>
WebLogicCluster wlserv1:7001,wlserv2.com:7001
MatchExpression *.jsp
</IfModule>
By using /bin/ls command i checked the following :
/bin/ls: ELF 64-bit LSB executable, x86-64, version 1 (SYSV), dynamically linked (uses shared libs), for GNU/Linux 2.6.18, stripped
Using file mod_wl_22.so i checked the following:
mod_wl_22.so: ELF 64-bit LSB shared object, x86-64, version 1 (SYSV), dynamically linked, not stripped
My problem is when i used ./apachectl -t i got the following error :
httpd: Syntax error on line 112 of /u40/app/apache/conf/httpd.conf:
Cannot load /u40/app/apache/modules/mod_wl_22.so into server: libstdc++.so.5:
cannot open shared object file: No such file or directory
So can u please guide me where my problem is and how to rectify it ? Its urgent. please help me.
Thanks
Jyoti Ranjan

LMS 4.2 EoL Report Location issue

After upgrading to 4.2 months ago, I've noticed that the EoL report has been moved to the new interface.   Though it's a welcome change, there's an option that's since disappeared which I used on a weekly basis.   There was an option for saving the report to a specific location, where it would keep a "latest.htm" file that our CMDB team could pull for their own records for administration to view when they need.     As of right now, there's no option for this, and it only lists what type of e-mail attachment to use.
One would think that the reports would be saved in the default report repository that's specified in the admin panel, but it's not saving those reports to that area. I'm not certain where -if at all- it may be saving them.
Any ideas?

Hi,
i have reseted the ANI db using NMSROOT\bin\perl.exe NMSROOT\bin\dbRestoreOrig.pl dsn=ani dmprefix=ANI
Everything is set to 0:
Topology Data Collection      0 0 Not Available                          Running Schedule
UT Major Acquisition            0 (0 End hosts 0 IP Phones) 0      Not Available Idle Schedule
VRF Collection                    0 0                                              Not Available Idle Schedule
But Topology Data Collection is still frozen to "Running" state....

Some end hosts are missing!

Hello.
I'm using CiscoWorks LMS 4.0.1. For one subnet, User Tracking does not show IP address for some end hosts only (printers). All devices are supported, ARP table is populated. Ping sweep is enabled for all subnet.
Any ideas?
Regards.
Andrea

when your MAC is ok, the LMS can query the switch.
The next step for LMS is to query the gateway (router), for the MAC to get the IP.
So when your IP is missing, it could be that the LMS doesnt have access or can query to gateway that holds the Info.
maybe the printers use a different gateway, or the LMS doesnt have the access to that gateway.
Also in the other end , i guess a database problem also can occur, that will give the same result.
have you tried to purge the UT database ?
Also there is a setting around UT in DHCP environments. are this on ?

Problem configuring front end host for weblogic cluster

hi,
I am using weblogic 8 sp4,I have a cluster of WLI servers for which i am trying to configure a front end host.I am using apache Http server 2.0.55 for the same.
I copied the mod_wl_20.so file to the modules directory and added the following to httpd.conf file
LoadModule weblogic_module modules/mod_wl_20.so
<IfModule mod_weblogic.c>
WebLogic http://myIP:9191,http://myIP:9192,http://myIP:9193
ErrorPage http://myerrorpage1.mydomain.com/
MatchExpression *.jsp
MatchExpression *.xyz
</IfModule>
<Location /weblogic>
SetHandler weblogic-handler
PathTrim /weblogic
</Location>
however,the error page gets displayed and not the default weblogic page.
When I change the Error page url to that of my cluster url(i.e)http://myIP:9191, the weblogic default page gets displayed .. I mean to say that the same url doesnot work with the WeblogicCluster parameter but works with
the ErrorPage parameter.
Somebody who has configured the front end host using apache http server please clarify, it would be of great help.
Thanks in advance

The error.log displays the following (sorry i forgot to add it above :-()
[Thu Nov 24 15:46:40 2005] [notice] Apache/2.0.55 (Unix) configured -- resuming normal operations
[Thu Nov 24 15:46:56 2005] [error] Port number specified in WebLogicCluster parameter specified in httpd.conf is not an integer less than 65535
[Thu Nov 24 15:46:56 2005] [error] CONFIG_ERROR [line 1344 of ap_proxy.cpp]: Port number specified in WebLogicCluster parameter specified in httpd.conf is not an integer less than 65535

LMS 4.2.4 - report check "end host" list

Similar Messages

Maybe you are looking for