LMS 4.2 | Archival Summary failed

Hi Netpro
at the Archival Summary failed part the reason behind the failure is as below , pls how to solve this issue and let lms download all configuration from the devices
TELNET: Failed to establish TELNET connection to 10.1.1.9 - Cause: Authentication failed on device 3 times.
PRIMARY-RUNNING config Fetch Operation failed for TFTP. Could not detect SSH protocols running on the device Failed to fetch config using RCP. Verify RCP is enabled or not
Thanks
ibrahim

I was referring to the LMS server. From the Device Center where you checked the credentials, you can choose "Tools, Edit Device Credentials". from the window that opens up from that, re-type your SNMP RW credentials to verify that you are using the correct ones as configured on the device.
After you do that, then re-submit the Archive job and telll us your results.

Similar Messages

Config Archive Mgmt failed LMS 3.2

Hi
Archive mgmt failed for 14 devices and working fine for only 2 devices..The communicaion between the LMS and Switches is through SSH,but ssh also failed.
Thanks,

Hey Clarke,
Hope you;re doing well,
i have tried from ur below instructions,i have attached logs from packet capture and the tftp permission denied error.
Am receiving an error permission denied while copying vlan.dat file from switch to tftp server (LMS Server) same error i can see in packet capture,Is it anywhere in LMS server i have to give permission for TFTP server.
I tried installing a different vendor TFTP server but the LMS TFTP is listening on this port.How can i disable the tftp port on LMS server and open for open vendor product such tftpd32.exe OR solarwinds tftp server.
LMS Server IP add 10.28.73.50 and the switch IP add 10.28.72.2
Awaiting ur reply soon.

LMS 3.21 Archive Issue

Hi,
Below is deatils of an issue I am having with my 2900 routers, which I cannot backup (taken from dcmaservice.log).
All other devices are working fine.
Is the a bug fix ?
Thanks
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-5],com.cisco.nm.rmeng.dcma.configmanager.ConfigManager,updateArchive,1943,Sync Archive for 1 devices - Sync Archive
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-5],com.cisco.nm.rmeng.dcma.configmanager.ConfigManager,updateArchive,1957,Number of devices in fetch Q = 0
[ Wed Jul 04 10:28:37 BST 2012 ],WARN ,[Thread-5],com.cisco.nm.rmeng.util.DCRWrapperAPIs,getResultFromQuery,3315,SQLException occurred as connection closed. Re-connecting to DB...
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-5],com.cisco.nm.rmeng.dcma.configmanager.CfgThreadManager,compareDeviceWithDevicesinRunningThreads,59,inside compareDeviceWithDevicesinRunningThreads method
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-5],com.cisco.nm.rmeng.dcma.configmanager.CfgThreadManager,compareDeviceWithDevicesinRunningThreads,60,Total running threads:5
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-5],com.cisco.nm.rmeng.dcma.configmanager.ConfigManager,updateArchiveIfRequired,2057,Compared the device with running thread devices.Adding to Fetch Q
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-5],com.cisco.nm.rmeng.dcma.configmanager.CfgThreadManager,triggerConfigFetch,52,#### Start of Sweep Wed Jul 04 10:28:37 BST 2012 ####
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericConfigOperator,fetchConfig,70,I am here
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericCliOperator,registerPlatform,95,Calling new GenericPlatform()
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericPlatform,<init>,23,setting GP user and pass prompts
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericPlatform,<init>,30,registering generic platform
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericPlatform,<init>,32,registered generic platform
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.rmeng.util.rmedaa.RMEDeviceContext,getCmdSvc,1537,Inside RMEDeviceContext's getCmdSvc ....
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.rmeng.util.rmedaa.RMEDeviceContext,getCmdSvc,1547,Protocol and Platforms passed = SSH , GEN
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.rmeng.util.rmedaa.RMEDeviceContext,getCmdSvc,1571,Iam inside ssh ....
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.rmeng.util.rmedaa.RMEDeviceContext,getCmdSvc,1573,Initial time_out : 0
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.rmeng.util.rmedaa.RMEDeviceContext,getCmdSvc,1583,Computed time_out : 36
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.rmeng.util.rmedaa.RMEDeviceContext,getCmdSvc,1599,After computing time_out : 36
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.rmeng.util.rmedaa.RMEDeviceContext,getSshCmdSvc,1637,inside getSshCmdSvc with timeout : 36000
[ Wed Jul 04 10:28:37 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.rmeng.util.rmedaa.RMEDeviceContext,getSshProtocols,1743,Inside getsshprotocols with time out : 36000
[ Wed Jul 04 10:28:38 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.rmeng.util.rmedaa.RMEDeviceContext,getSshCmdSvc,1651,SSH2 is running
[ Wed Jul 04 10:28:39 BST 2012 ],ERROR,[Thread-384],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,error,19,Unknown authentication method: keyboard-interactive
[ Wed Jul 04 10:28:43 BST 2012 ],ERROR,[Thread-384],com.cisco.nm.rmeng.dcma.configmanager.ConfigManager,updateArchiveForDevice,1357,PRIMARY RUNNING Config fetch Failed for MIL-R-002
[ Wed Jul 04 10:28:43 BST 2012 ],INFO ,[Thread-384],com.cisco.nm.rmeng.dcma.configmanager.ConfigManager,writePerDeviceResultFile,2445,Serializing the Device Result = D:/CISCOW~2/files\/rme/jobs\ArchiveMgmt\1108/31.device
[ Wed Jul 04 10:28:53 BST 2012 ],ERROR,[Thread-384],com.cisco.nm.rmeng.dcma.utils.ArchiveUtils,getDeviceReachabilityStatus,461,Telnet/SSH may be disabled on 172.31.255.25
[ Wed Jul 04 10:28:53 BST 2012 ],INFO ,[Thread-2],com.cisco.nm.rmeng.dcma.configmanager.CfgThreadManager,run,99,#### End of Sweep Wed Jul 04 10:28:53 BST 2012 ####

Hi,
I am still loking at the issue with no resolution.
I am trying Telnet, which all correctly configured and working (with Tacacs and have looked at the Taccas...ini file)
But still my archive jobs fail on LMS 3.2 for 2900 Routers
SSH - is beacuse of the client used on LMS has the "keyboard-interactive" mode setting set in its client cfg, which as it's a Java ssh client , it is not configuable and therefore needs a fix.
Telnet - seems to failing with authentication or prompt issues, with Tacacs enabled.
I have seen no resolutions to these issue.
Any ideas
Thanks

Event test "Archive Full (%)" failed: ora-28009:

Trying to create an event that will send an email with OEM but Im getting this message
Event test "Archive Full (%)" failed: ora-28009: connection to sys should be as sysdba or sysoper in the event viewer.
Im not sure what this refers to though - to connect to Management Server it has to be sysman user. What "connection" is this referring to ???
Oracle 9.2.0.5.0 (due to migrate to 10g at years end hurrah!)
Windows XP (now, but AIX once in production)

OK thanks for that. I went ahead and did this:
Configuration
Manage Administrators
Selected SYSMAN
Preferred Credentials
Selected target database and erased everything from the Database Credentials fields (where previously we had SYS/AS SYSDBA etc. )
I am getting the same darn error as before.
Anyway, the OEM help for this screen says
Role Select the role from the pull-down list. You need to login with the SYSDBA or SYSOPER role to start up or shut down a database.
Still stuck on this. I dont properly understand the error itself - it is telling me that the connection to sys should be as sysdba - and I am connecting as sysdba. ... . not sure what else I can do apart from try and write a script and forget this altogether.
Thanks
DA
Also, in the Event Viewer, according the documentation, there is an "advice" tab. I see no such tab. :(
When I try to create an event without any information supplied to the fields for SYSMAN Preferred Credentials, I get this in Event Viewer:
"Failed - ora-0:normal , successful completion."
Now I am really confused - a "failed, normal completion" ??
Message was edited by:
Dan A
Message was edited by:
Dan A

LMS 4.0 Archive Poller starts failing after some working cycles

Hi,
We have a LMS 4.0 running in our network with arround 650 nodes.
We are having problems with the Archive Poller.
The first few days it worked fine, but then it started to fail for some devices and on the next day it failed to poll all devices. I have restarted the daemon manager after the failure and it came back working fine for another few days. Since then the Change Poller works for a few days, then it degrades polling to a complete failure, a restart of the daemon manager get it working only for a few days.
Here is some output of a failed node:
*** Device Details for zagora4-sw ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> Telnet,SSH
Execution Result:
Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Admin > Collection Settings > Config > Config Job Timeout Settings
It seems that the poller is not even trying to poll nodes...?
Do you think the DB might got corrupted, as I restarted the machine without shutting down the processes some weeks ago...
Any hints or ideas would be appreciated !

Hi @ all
I have the same Problem as Ruslan. Do ansbody have a idea to solve this problem ? Afer some succesfull runs ob the ArchivePoll it stop with the mentioned error...
*** Device Details for nunw-n30-05-005 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> Telnet,SSH,HTTPS
Execution Result:
Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Admin > Collection Settings > Config > Config Job Timeout Settings
I´d tried to increase the "wait time" but notthing happens ...
HELP Please ...
Thanks
Regard Mario

LMS 3.2 Archive Update Job Failing

The scheduled archive update job is failing for all devices. Every one that I've checked is failing with the same message:
Execution Result:
Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Resource Manager Essentials -> Admin -> Config Mgmt -> Archive Mgmt ->Fetch Settings
This setting is at 120 seconds. I've tried adjusting this setting and get same results
Attaching job logs from most recent failure.
Thanks for any help.

Hi ,
Archive purge can fail for many reasons. I can suggest few things , If it did not work. You can open up a TAC case for troubleshooting.
Try this :
Increase the ConfigJobManager.heapsize as “1024m” in the following file:
NMSROOT/MDC/tomcat/webapps/rme/WEB-INF/classes/JobManager.properties (ie,,ConfigJobManager.heapsize=1024m) ·
Restart the daemon manager ·
Once the daemon manager is started successfully, Go to Admin > Network > Purge Settings > Config Archive Purge Settings, increase the “Purge versions older than:” to 12 Months (Also configure large value for no. of versions that you would like to have per device) and trigger the job. ·
Once job is completed, decrease the number of months gradually, until the desired no. of days & no. of versions required is reached. This exercise is to reduce the number of archives loading in memory during a purge job, which will cause job hanging.
Thanks-
Afroz
[Do rate the useful post]

LMS 3.2 Configuration Archival Summary

Hi,
Why does the Failed devices count increases after each unsuccessful archive sync? Is it a display issue?

Its to indicate that you have 5 devices that failed to get their archives and should address the issue by fixing the credentials since its reporting authentication failed.

LMS 3.2.1 RCP Failed

Hi,
I am using LMS 3.2.1 and unable to do the Software Repository job via RCP, because of the below error message.
Problem:
SW1#copy flash1:c2960s-universalk9-mz.150-1.SE.bin rcp://cwuser@CW-IPAddress:/CSCOpx/temp/rep_sw_4972128000394429365
Address or name of remote host [CW-IPAddress]? CW-IPAddress
Destination username [cwuser]? cwuser
Destination filename [D:/CSCOpx/temp/rep_sw_4972128000394429365]? D:/CSCOpx/temp/rep_sw_4972128000394429365
Writing D:/CSCOpx/temp/rep_sw_4972128000394429365
%Error opening rcp://cwuser@ CW-IPAddress /D:/CSCOpx/temp/rep_sw_4972128000394429365 (Undefined error)
LDNW-STKT-F00-SW2#copy flash1:c2960s-universalk9-mz.150-1.SE.bin tftp:// CW-IPAddress /rep_sw_1225718452630721792
Address or name of remote host [CW-IPAddress]? CW-IPAddress
Destination filename [rep_sw_1225718452630721792]?
SW1#
In the device, below are the rcp configurations
ip rcmd rcp-enable
ip rcmd remote-username cwuser
And also in the CS->Server->Admin->System Preferences, RCP user is configured as cwuser. Please advise, if I need to configure it some other settings.
Attached is the software deployment preferences.
Question:
Although CiscoWorks can successfully do the Inventory Collection and Sync Archive job of the same device.
Also as you can see above CiscoWorks can do Software Repository job via TFTP. As TFTP is not reliable, RCP is TCP protocol, I want to use RCP.
Please advise that why RCP is failing and how I can correct the RCP issue.
Thanks

This issue is resolved itself by rebooting the CiscoWorks Server.

LMS 3.2 Archiving Partially successful

Hi,
We have installed LMS 3.2,But for some of the switches archiving is partially successfull.Switches are 6500 in transparent mode.We use ssh for archive management.dcmaservice Log says...
[ Thu Jan 21 14:51:05 AST 2010 ],ERROR,[Thread-1540],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,error,19,Unknown authentication method: keyboard-interactive.In the RME I can see the log as Command Failed.

For RME to be able to fetch the VLAN config, it must be able to copy the vlan.dat file from flash back to itself using TFTP. RME will issue a command similar to:
copy flash:vlan.dat tftp:
Make sure the device can properly copy the vlan.dat back to the RME server using TFTP.

Cisco LMS. Config Archive

Good day
Recently we've installed LMS 4.2. And also we've configured archive backup, but jobs weren't successfull. I'm getting error check credentials or increse timeout. But procedure of checking device credentials was successfull. I've checked onl ssh transport for archive is it correct?

This can be long to troubleshoot if you talk about various devices. You have to target device by device as reason of failure may differ for each device.
1. Run a job to archive config from a device and share the screenshot of result, if fail.
2. Share the DCMAService.log from server, also enable debug before you run the job for syncarchive.
3. Open device in Device centre and run a credential verification job to see if it succeeds.
4. Try to increase the timeout for telnet and read delay to almost double of what is configured.
Share the result once this is checked.
-Thanks
Vinod

LMS 3.2 device updates failing?

Have upgraded from LMS 3.1 to 3.2 then applied all the software updates ok.
Now applying device updates - they are failing but can't see a clear reason. The Activity Log > Event Log doesn't really provide any clues. I'm guessing the relevant log file would be the psu.log ? [see attached]
Not sure if messages like
oid : 1.3.6.1.4.1.11.2.3.7.5.19 not found in E:\CISCOW~1\lib\classpath\com\cisco\nm\cwcs\mdf\mdfdata.xml
are part of the problem?
Thanks for any troubleshooting pointers

The SYSobjectID you mention is of an HP device so that is not likely to be your problem.
Got any problems with devices not being recognized?
Tail of psu.log looks normal to me.
Cheers,
Michel

Problems upgrading from LMS 3.0 to LMS 3.2 - the backup fails.

I'm upgrading from LMS 3.0 to LMS 3.2 on Solaris. I've met all of the prereq's, patches, etc. It keeps failing on the Backup...It claims I need 15 Gig for the backup. The backup directory I'm using (/opt/backup) has 35 Gig free, so that shouldn't be the issue.
Here is the error I'm seeing in the backup.log;
okcwsi:tail backup.log
tar: /var/adm/CSCOpx/files/rme/dcma/shadow/sw_images/cisco_configs/sw_images/cis
co_configs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/cisco_confi
gs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/c2950-i6q4l2-mz.121
-13.EA1c.bin: prefix is greater than 155
tar: /var/adm/CSCOpx/files/rme/dcma/shadow/sw_images/cisco_configs/sw_images/cis
co_configs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/cisco_confi
gs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/c1310-k9w7-tar.124-
10b.JDA2.tar: prefix is greater than 155
tar: /var/adm/CSCOpx/files/rme/dcma/shadow/sw_images/cisco_configs/sw_images/cis
co_configs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/cisco_confi
gs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/c2800nm-advsecurity
k9-mz.124-22.T1.bin: prefix is greater than 155
tar: /var/adm/CSCOpx/files/rme/dcma/shadow/sw_images/cisco_configs/sw_images/cis
co_configs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/cisco_confi
gs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/c3560-ipbase-mz.122
-53.SE2.bin: prefix is greater than 155
tar: /var/adm/CSCOpx/files/rme/dcma/shadow/sw_images/cisco_configs/sw_images/cis
co_configs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/cisco_confi
gs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/c7600-fpd-pkg.122-3
3.SRE1.pkg: prefix is greater than 155
tar: /var/adm/CSCOpx/files/rme/dcma/shadow/sw_images/cisco_configs/sw_images/cis
co_configs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/cisco_confi
gs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/c7600s72033-advente
rprisek9-mz.122-33.SRE1.bin: file name too long
tar: /var/adm/CSCOpx/files/rme/dcma/shadow/sw_images/cisco_configs/sw_images/cis
co_configs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/20100922075
156561-10.181.252.1.cfg: No such file or directory
ERROR(704): Cannot create or back up tar file. Backup cancelled. Verify that you
have write-access to this directory.
Backup failed: 2010/09/22 07:54:20
okcwsi:
I've tried this multiple times and each time it appears to fail on a different file/folder in the sw_images directory. This is our FTP directory where we store lots of IOS images for download. I've removed each of these files it errors out on and it keeps failing. I just removed all files from the sw_images folder and am trying the backup again now.
I'm attaching the backup.log which contains the failure information for each backup I've tried in the past two days.
My main question is...can I skip this backup somehow? I've got another LMS 3.0 system that I can export everything I need from. Skipping the backup isn't an option on the install/upgrade? It gives me the option to quit the install or try the backup again.
Thanks,

You can skip the backup with a hidden option:
./setup.sh -b nobackup
However, I wouldn't feel comfortable until figuring out why the backup has been failing, ostensibly because tar is running into the 255-char limit (100 for the filename and 155 for the path), a result of the many iterations of the following:
sw_images/cisco_configs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/cisco_configs/sw_images/

V6 quiz report LMS as completed after 3 failed attempts

I have a pure quiz in captivate 6 that allows the learner to take it 3 times only eg
Attempt 1 = fail = report LMS incomplete
Attempt 2 = fail = report LMS incomplete
Attempt 3 = fail = report LMS incomplete
What i need is not logical but.........
I require the LMS to
Attempt 1 = fail = report LMS incomplete
Attempt 2 = fail = report LMS incomplete
Attempt 3 = fail = report LMS complete
Is this at all possible?
Happy to try anything with instructions
Thank you in advance and hope the above is clear enough
Jo

Hmm, very illogical indeed. Not consistent with normal SCORM behavior at all.
Just some ideas, without having checked them completely. You are using score or completion of slides as criterion? If it is the last option, make sure there are some slides to be viewed after the last attempt by using the Action on Fail that you'll find in the Quiz Preferences. I hope that is the case. But what if you have to report a score?
Lilybiri

LMS 3.1 Inventory Collection fails

I have the same problem as the following post:
https://supportforums.cisco.com/thread/176673?tstart=0&viewcondensed
Also, LMS fails inventory collection every time. I click on the "failed" link from LMS Portal, but the page never comes up detailing why it has failed. This is after I fixed an issue with group policy overwriting the "Logon as batch" setting for casuser. Everything appeared to be up and running normally again, when I noticed the next day that inventory polling/collection is failing. pdshow attatched.
The following error message continues to show up in the rme_ctm.log file:
[ Tue Feb 22 07:40:55 CST 2011 ] URN_NOT_FOUND : urn "JRM" : Not found !!
The last entry in the CTMJrmServer.log file is:
[ Thu Feb 10 10:52:55 CST 2011 ],INFO ,[main],com.cisco.nm.rmeng.jrmwrapper.server.CTMJobManagerServer,publishDaemonOk,99,Called CreateReady file. Return Value 0
I've been blindly trying to chase this down and getting nowhere.

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
Hi ,
Great ..
The issue was this Port was blocked 47001, which was blocked . what we did will skip that Port and
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
the ctmregistry should have EssentialsDM on a new port, and the conflict should not reoccur.
Thanks--
Afroj

LMS 3.1 Backup job Failing

Hello,
We have LMS 3.1 installed and the backup is failing with the following message
[Tue Feb 8 09:20:26 2011] ERROR(247): E:/Backup_3/backup.LOCK file exists
Most probably another backup process is running
[Tue Feb 8 09:20:26 2011] Backup failed: 2011/02/08 09:20:26
I tried to do the following, but it didn't work:
1- Run again the backup job, but specify a new backup directory folder (ex: E:/Backup_4/). --> Did not work
2- - Stop the Deamon Manager service using: net stop crmdmgtd --> Did not work
     - Delete the backup.LOCK file from the E:/Backup_3/ folder
     - Restart the Deamon manager service using: net start crmdmgtd
     - Run the backup job again using the new Folder destination.
Please Advise,
Regards,

I am currently working on a same issue with LMS 3.1 on windows;
After stopping dmgtd have you been able to delete the backup.lock or have you restarted the server?
In my case I was not able to delete the file and it turned out dbvalid.exe blocked this. The backup seems to run without any problems. When the backup is done dbvalid.exe trys to verify the backup database files. This validation fails and dbvalid starts dbsupport.exe to get some detail information on the failure and trys to send them to Sybase support. You should find (several ?) crash files here: %ALLUSERSPROFILE%\Application Data\SQL Anywhere 12\diagnostics. dbsupport.exe seems to be started interactively and thus hangs up waiting for some user input...
In the crash file I see dfmInv mentioned as the database which did not pass dbvalid. I assume I will end up reinitializing the dfm databases to recover - but let's wait and see. I found some hints that there could be a bug with dbvalid.exe form Sybase- not sure if this is the culprit or a real DB error. What I found really strange is the cli of dbsupport.exe (see the option -gui at the end... )
D:\PROGRA~1\CSCOpx\objects\db\win32\dbsupport.exe" -crash "C:\Documents and Settings\All Users\Application Data\SQL Anywhere 10\diagnostics\SA10_20110215_040218_4348.crash_log" -crashpn "dbeng10" -crashsn "dbvdfmInvEng" -gui
Also, I would quickly backout the last know good backup from the backup directory - just in case... (the one before the failure raised the first time)

LMS 4.2 | Archival Summary failed

Similar Messages

Maybe you are looking for