LMS 4.2 - Config collection issue

After launching config collection job in LMS 4.2 I can't get job results and receive error message - Unable to get results of job execution for device...
I've increased the job result wait time using option in Admin > Collection Settings ... , but nothing changed.
Here are screenshots of error message and wait settings I used:
Thanks in advance!

i have seen this with SNMP timeout needed to be increased.
please try to increase those values, and not the job completion values.
I just saw in CP LMS 4.2 that the values are assembled on a new page.
all of them ...
Admin > Network > Timeout and Retry Settings > Inventory/Config Timeout and Retry Settings
also in the navigator of the same last windows your screenshot is from try the device specific timeouts:
Admin > Collection Settings > Config > Edit the Inventory/Config Timeout and Retry Settings
HTH

Similar Messages

  • LMS 4.0 Config collection vlan.dat

    Hi Guys,
    I have a network with 4500, 3560 and 2960 switches.
    In my LMS I have created 1 credential set to access all the switches. The config collection (startup, running and vlan) has succeeded for all the 2960 switches. The collection of the running and startup config has also succeeded for the 4500 and 3560 switches. But LMS doesn't collect the vlan.dat from the 4500 and 3560 switches. (inventory collection is ok with all the switches).
    I have only configured SSH as config fetch protocol.
    Why doesn't my LMS collect the vlan.dat of the 3560 and 4500 switches. The difference between the 2960 and the other switches is that there are only 2 vlans created on the 2960 switches and +30 vlans on the 3560 and 4500 switches.
    Is the vlan.dat file maybe to big on the 3560 and 4500 to be collected with ssh...
    Any ideas?
    Thanks,
    Best Regards,
    Joris

    I believe that LMS 4.2 can get the vlan.dat via SCP. Prior versions require TFTP to do this.
    The commands to start the TFTP can be send via TELNET, SSH and possibly SNMP.
    Cheers,
    Michel

  • LMS 4.0 Config Collection failure

    Hello Members,
    i've added manually a bunch of Cisco Router 2911's and 2801's. On one of the the 2911 and 2801 the Config Collection fails. Data Collection, User Tracking, Inventory and Fault Discovery worked fine for all routers just on the two routers i get the failure?
    any ideas? Which log do i have to check?
    regards
    alex

    I believe the LMS reports this error because there was no vlan.dat in the
    flash of the router. after adding a vlan.dat file on in the flash the vlan config
    could be fetched and the error message doesn't appear any more.
    regards
    alex

  • LMS 3.2 Data Collection Issue

    Hi ,
    I have LMS 3.2 and license for adding 5000 devices , my data collection is running continously for the past 2 days, when i try to stop the daemon manager and restart it comes to idle state but after some time it again goes to Running state
    I am not getting the best practices deviations and discrepaqncies report after this issue
    I am attaching the ANIServer.properties , ani.log and ANIServer.log file
    Please help

    this seems to be BugID CSCtd49439:
    http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?caller=pluginredirector&method=fetchBugDetails&bugId=CSCtd49439
    also consider to install the patch for BugID CSCtg20882:
    http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?caller=pluginredirector&method=fetchBugDetails&bugId=CSCtg20882
    if you have CM 5.2 you should consider to upgrade to CM 5.2.1 which is available here:
    http://www.cisco.com/cisco/software/type.html?mdfid=282641773&flowid=5141&softwareid=280775108
    the patches for BugIDs CSCtd49439 and CSCtg20882 are availabel by contacting TAC

  • Ciscoworks LMS 4.1 Inventory Collection issue

    We are having an issue with device inventory collection when a device or component in a device is replaced. The inventory collection job appears to be successful but the changes to devices or modules are not retreived. Short of deleting an object and adding back in, are there any configuration changes that can be made or patches that can be applied to LMS to pick up these inventory changes?

    Yes, deleting and re-adding the device works. However, changes have been made to multiple devices in the environment and aside from a bulk delete and re-add there is no guarantee that all changes to all devices will be identified and captured. the side effect will be a loss of historical data.
    Are there any options other that deleting and re-adding that will allow the application to identify the inventory changes, or is this a limitation of the product?
    Are there any items we should check to identify a potential underlying issue?

  • Lms 4.2 , Config Archival issue

    Hi
    Please have a look to the below image , what is the reason for this failed Archival and  how to solve this issue
    thanks
    Ibrahim

    The 25 success means LMS is working fine.
    The 277 failed means LMS has problems communicating with these devices.
    Causes can be:
    Bad credentials
    ACL's on the device not permitting LMS ip address to talk to the device.
    protocols (TELNET, SSH, RCP, SCP) not running on the devices.
    firewalls or ACL's on routers not permitting LMS protocols.
    Pick a single device, test the protocols comming from the server to the device, test credentials.
    Cheers,
    Michel

  • LMS 4.1 Energywise Endpoint issue

    I have 10 switches as members of the same, local, energywise domain.  When I perform a show energywise neighbors on any of the given switches, they all appear.  If i perform show energywise children on a given switch, i see the children of that switch.
    When i attempt to "Collect Endpoints" the collection is a success, but my 10 switches only show 2 endpoints, which are 2 of the 10 switches that are configured as a stack.  When i remove that stacked 3750G from the energywise domain, it still only shows 2 endpoints, but now they are 2 other switches that are configured as a stack.
    Is it that LMS 4.1 has difficulty detecting endpoints in a group where Stack switches are used, or am I missing something in my config?  LMS 4.1 says it "knows the secrets" and has not had a single Energywise query error out, so i can only assume its gathering all the information its supposed to be, but somehow it never detects any of my actual endpoints, only the 1st set of stacked switches in the group.

    Hello,
    Are you sure that the LMS support the config collection on these devices ?
    Check on this link :
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/device_support/table/lms41sdt.html
    If yes, it means that you have a problem for the file transfer... I would suggest to debug like this :
    1) Check the credentials (Inventory->Job Browser->Device Credential Verification Jobs, then create a new one)
    2) Is it possible to do a tftp from the device to the LMS ? (If the config is done by tftp)
         Create a tmp file on /tftpboot on LMS
         Copy the startup or running file from the device to the LMS with the name of your tmp file (it is not allowed to create a file on the LMS with TFTP)
    3) Do a sniffing of the traffic between the LMS and the device in order to see what happen
         Go on :1741/cwhp/PacketCapture.do">http://:1741/cwhp/PacketCapture.do
    BR

  • Config collection fails occasionally in LMS 4.2

    Hello,
    In recently installed  LMS 4.2 archive collection is failing from time to time for random number of devices with error:
          "Execution Result: CM00139 Could not archive config Cause: Action: Verify that device is managed and credentials are correct. Increase timeout value, if required."
         We have sceduled config collection job to run every day. Credentials are ok. The LMS data is restored from LMS 3.2. Timeout seeting is the same as in LMS 3.2 and we never had this problem before.
         Somtimes it is working for 10 days correctly, and then one day it is not successful for 70 out of ~150 device. Then t is successfull for few days, then again fails for  86 devices. Collction is scedueld in the evening so devices are not overloaded, nor there is some other job in LMS running at the same time.
         Any ideas?
         Thanks,
         Marija
    I

    The following did resolve my issue
    The bug is fixed in the one of the latest device packages for LMS, SharedSwimIOS.RME525.v2-13-3. The release notes for it is here: http://www.cisco.com/web/software/283418817/118429/SharedSwimIOS.RME525.v2-13-3.readme.txt
    Before applying that device package update, the following prerequisites need to be met:
    - LMS 4.2.5
    - MDF 1.92 (or higher) update : https://software.cisco.com/download/release.html?mdfid=284259296&flowid=37207&softwareid=283716219&release=Mdf.%201.92&relind=AVAILABLE&rellifecycle=&reltype=latest
    - LibSwim.RME525.v2-13-1.zip & SharedDcmaIOS.RME525.v5-1-2.zip device packages already installed. Those two files and the  SharedSwimIOS.RME525.v2-13-3 file can be found here: https://software.cisco.com/download/release.html?mdfid=284259296&flowid=37207&softwareid=283418817&release=AutoDev%285.8%29&relind=AVAILABLE&rellifecycle=&reltype=latest

  • Cisco lms - config collection

    Hi, i'm looking for a way to collect config's from specific devices periodically, is this possible?
    for example, collect configs from firewalls everyday at midnight , and collect routers config once a week.
    firewalls: (about 3 devices, config changes every day)
    routers: (about 800 devices, rarely change the config)
    the only config collection schedule i have found so far is too simple:
    admin > collection settings > config > config collecion settings > periodic collection
    second question, is it possible for cisco lms to send via e-mail the diff of the config pulled from devices? i mean the specific commands that have appeared in the new configuration file.
    regards, ignacio

    Unfortunately, LMS syslog mechanism is very minimalistic and doesn't have a lot of options to it.
    However, the feature you're requesting is not very much LMS dependent. As, Ciscoworks depends on the kind of syslog message it receives from device, based on it, it captures some characters to send a notification as automated actions.
    So usually it is the device which won't send a lot of information on what changes was done by which user in normal IOS syslog messages.
    But, to certain extent, you can try to configure you device for Configuration-Change logger to receive details on what changes were made by users and check it on the syslog report, or configure AA on it for all or important devices.
    You can enable a configuration logger to keep track of configuration changes made with the command-line interface (CLI). When you enter the logging enable configuration-change logger configuration command, the log records the session, the user, and the command that was entered to change the configuration. You can configure the size of the configuration log from 1 to 1000 entries (the default is 100). You can clear the log at any time by entering the no logging enable command followed by the logging enable command to disable and reenable logging.
    Use the:
    show archive log config {all | number [end-number] | user username [session number] number [end-number] | statistics} [provisioning] privileged EXEC command to display the complete configuration log or the log for specified parameters.
    This example shows how to enable the configuration-change logger and to set the number of entries in the log to 500:
     Switch(config)# archive 
     Switch(config-archive)# log config
     Switch(config-archive-log-cfg)# logging enable
     Switch(config-archive-log-cfg)# logging size 500
     Switch(config-archive-log-cfg)# end
    So, in all, it depends on the device and the kind of syslogs it send for LMS to react on it.
    -Thanks
    Vinod
    **Encourage Contributors. RATE Them.**

  • CiscoWorks-Config collection problem

    Hi,
    I have configured config collection on Cisco Works. But only one device's configuration has been succesfully collected, rest of the devices are showing failed.
    check the log...showing telnet authentication failed 3 times.  but I have checked the username and password configured on Cisco Works is perfect even the same username and password configured on the device, which configuration collection succeded.
    Please give me some troubleshooting process so I can fix the issue.

    yes..I have checked so many times...and username / password is ok....but still I am not able to fix the problem.....It the username and password is configured wrong , then it should work for one device,,,because the username and password is configured in Tacacs Server and same for all devices.

  • Folks, How do you stop tftp being tried for Config collection ?

    Hi there. We use LMS 3.2 with RME 4.3.1.[Solaris 10].
    tftp is band across our network. So we don't use tftp remotely.
    I've removed tftp from the RME config transport settings. [I just allow SSH / SCP ]
    We still get 'couldnot determine the tftpboot directory. VLAN Config fetch is not supported using SCP'.
    How can config RME to not even attempt to use tftp when pulling back switch configs ?
    We don't want the old vlan.dat database form our older switches. Config collection also tries to tftp to routers to pull back the VLAN config.
    Please have a think ? Many thanks. Guy

    So it still tries anyway?
    Well, if you use SSHand RCP/SCP you could try to disable the TFTPserver of ciscoworks.
    It is a regular windows service (on the windows version of LMS ofcourse) just stop and disable it.
    Archive will fail because it can't get vlan.dat ofcourse but that is how RME is hardcoded
    Cheers,
    Michel

  • Has any seen collection issues after 11g database upgrade?

    We do have an SR open.
    Just wondering if anyone else has experienced collection issues after upgrading the db to 11g? Our technical folks are hoping it is something else but for the past few weeks we have seen random issues stemming from collections. We run a full collections 5 nights a week. There are material transactions occurring during the two plus hours of collections. This seems to be randomly skewing on hand snapshots in collections as well as missing supply i.e. work orders. Only impacts a fraction of the records in material transactions and they are different every night.
    Reason I believe it has to do with transactions during collections is one collection run out of the five is generally pretty good...Sunday evening for there is very limited transactions taking place on this evening.
    Thanks in advance

    Answer to above question not required now as:
    Having read the 24th December update of note 761570.1 - 'Database Preparation Guidelines for an Oracle E-Business Suite Release 12.1.1 Upgrade' I have decided to upgrade the database to 11.2.0.x by following the Path C option.
    Unfortunately as the 11.2.0.x upgrade isn't covered by MWIZ yet I will have to follow the manual steps.

  • LMS 4.2 Topology Data Collection Issue

    Hi there,
    i have an issue with the lms 4.2 Topology Data Collection. After installation the Topology Data Collection was running normaly, but since first server reload the Topo Data Collect under Inventory > Dashboards > Device Status > Collection Summary is "frozen". It only shows the following content from first run:
    Topology Data Collection    193    0    Not Available     Running    Schedule
    Is there any option to stop this process elsewhere? I cannot find anything under jobs in running state or so. Clicking on Schedule only give me the option to start data collection, but lms always returns that the process is running.
    Thanks for help.

    Hi,
    i have reseted the ANI db using NMSROOT\bin\perl.exe NMSROOT\bin\dbRestoreOrig.pl dsn=ani dmprefix=ANI
    Everything is set to 0:
    Topology Data Collection      0 0 Not Available                          Running Schedule
    UT Major Acquisition            0 (0 End hosts 0 IP Phones) 0      Not Available Idle Schedule
    VRF Collection                    0 0                                              Not Available Idle Schedule
    But Topology Data Collection is still frozen to "Running" state....

  • LMS 4.2.5 Syslog/Automated Action/Config mgmt issue

    LMS 4.2.5 on Windows
    We use the server as it's own Syslog server. The Syslog collector status is fine. I see syslogs coming into the server. However, I just made some changes on a router so ran a syslog report on it, but nothing was returned. I Tested the Collector Subscription and everything was fine.
    We also have Automated Actions configured on certain syslog messages (duplex mismatch for example). There is an AA configured to send my team e-mails when this event occurs. There was a device that had two days worth of syslog messages complaining about this issue. Yet, we only received about 10 e-mails from the LMS system on it.
    Another issue is with Configuration Mgmt. I fixed the duplex mismatch listed above and went to check the config tree to see if or when something changed. The last config archive was pretty old and I know changes were made on the device since then. This tells me that the LMS server didn't get notified of the config change or it would have gone out and checked it.
    The one thing in common on all of the above is Syslog messages. LMS will take actions based on receiving these messages and those actions don't seem to be firing.
    Any ideas would be greatly appreciated.
    Thanks,
    Mike S.

    To confirm if the device is sending the syslogs and they are being received by LMS server properly, check the $NMSROOT/log/syslog.log and see it has the syslog from the device.
    Unless syslog is there on syslog.log, we don't expect LMS to react on any AA. 
    For configuration backup, try to sync the device config by initiating a manual job to update the latest configuration from device. Even if there is no Automated Action working, you should still have a reoccurring/scheduled job configured to archive configuration backup periodically.
    Following is a document I created for Syslog troubleshooting :
    Ciscoworks LMS : Syslog in a Nutshell!
    -Thanks
    Vinod
    **Encourage Contributors. RATE Them.**

  • LMS 3.1 Inventory Collection fails

    I have the same problem as the following post:
    https://supportforums.cisco.com/thread/176673?tstart=0&viewcondensed
    Also, LMS fails inventory collection every time.  I click on the "failed" link from LMS Portal, but the page never comes up detailing why it has failed.  This is after I fixed an issue with group policy overwriting the "Logon as batch" setting for casuser.  Everything appeared to be up and running normally again, when I noticed the next day that inventory polling/collection is failing.  pdshow attatched.
    The following error message continues to show up in the rme_ctm.log file:
    [ Tue Feb 22  07:40:55 CST 2011 ] URN_NOT_FOUND : urn "JRM" : Not found !!
    The last entry in the CTMJrmServer.log file is:
    [ Thu Feb 10  10:52:55 CST 2011 ],INFO ,[main],com.cisco.nm.rmeng.jrmwrapper.server.CTMJobManagerServer,publishDaemonOk,99,Called CreateReady file. Return Value 0
    I've been blindly trying to chase this down and getting nowhere.

    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0in 5.4pt 0in 5.4pt;
    mso-para-margin:0in;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:11.0pt;
    font-family:"Calibri","sans-serif";
    mso-ascii-font-family:Calibri;
    mso-ascii-theme-font:minor-latin;
    mso-fareast-font-family:"Times New Roman";
    mso-fareast-theme-font:minor-fareast;
    mso-hansi-font-family:Calibri;
    mso-hansi-theme-font:minor-latin;}
    Hi ,
    Great ..
    The issue was this Port was blocked 47001, which was blocked . what we did will skip that Port and
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0in 5.4pt 0in 5.4pt;
    mso-para-margin:0in;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:11.0pt;
    font-family:"Calibri","sans-serif";
    mso-ascii-font-family:Calibri;
    mso-ascii-theme-font:minor-latin;
    mso-fareast-font-family:"Times New Roman";
    mso-fareast-theme-font:minor-fareast;
    mso-hansi-font-family:Calibri;
    mso-hansi-theme-font:minor-latin;}
    the ctmregistry should have EssentialsDM on a new port, and the conflict should not reoccur.
    Thanks--
    Afroj

Maybe you are looking for