LMS4.0/IPM: can't configure a dns collector
Hi,
Customer has lms 4.0 on windows.
He can't create a dns collector on IPM :
When we look at config device, device supports dns collector:
device_name #sho ip sla mon app
IP Service Level Agreement Monitor
Version: Round Trip Time MIB 2.2.0, Infrastructure Engine-II
Time of last change in whole IP SLA Monitor: 10:50:17.069 METDST Wed Apr 20 2011
Estimated system max number of entries: 30321
Estimated number of configurable operations: 30320
Number of Entries configured : 1
Number of active Entries : 0
Number of pending Entries : 0
Number of inactive Entries : 1
Supported Operation Types
Type of Operation to Perform: dhcp
Type of Operation to Perform: dns
Type of Operation to Perform: echo
Type of Operation to Perform: frameRelay
Type of Operation to Perform: ftp
Type of Operation to Perform: http
Type of Operation to Perform: jitter
Type of Operation to Perform: pathEcho
Type of Operation to Perform: pathJitter
Type of Operation to Perform: slm atm interface
Type of Operation to Perform: slm atm pvc
Type of Operation to Perform: slm controller
Type of Operation to Perform: slm frame-relay interface
Type of Operation to Perform: slm frame-relay pvc
Type of Operation to Perform: slm interface
Type of Operation to Perform: tcpConnect
Type of Operation to Perform: udpEcho
Type of Operation to Perform: voip
IP SLA Monitor low memory water mark: 41392015
Many thanks for your help,
Elisabeth
There is no default DNS operation because a DNS operation requires one to specify the DNS server. Before DNS will show up in the create collectors interface, you must create a new DNS operation under Monitor > Performance Settings > IPSLA > Operations.
Similar Messages
-
Can we configure SAP server installed in RHEL in windows sapmmc?
Can we configure SAP server installed in RHEL in windows sapmmc(Which is also sap server with same version and same DB)?
I have tried to configure using help from previous post in SCN ( SAP MMC in one server to control the entrie landscape ) but it is not working... As picture shown below after entering the details am clicking on add but nothing is happening...
Scenario is I have installed 4 VM's with SAP installed in all (out of it 3 linux and 1 windows) & all communicating well and they are in same Network/Landscape & I can configure/manage/logon all servers in host GUI... But If I shutdown my VM or a Laptop... Every time I have to start all the servers... by starting lsnrctl, DB, sap for all the servers,
Is there any chance to configure sap in windows sapmmc...???
Kindly suggest the process step by step...
Thanks in advance...Hi Yüksel
Thank you for the reply It helped me to configure but i struck in some place.. Dispatcher is getting stopped... I tried to add 3 different sap servers in sapmmc and tried to start.. Three are getting same errors(Guess same error)
After your suggestion i was able to configure and start SIDadm of host but immediately or after 30sec Dispatcher gets stopped tried to find out some solutions but didnt worked... But i was able to start from there servers manually in linux way startsap, but not in SAPMMC way...
Could you or please help me in solving trace given below...
trc file: "dev_disp.new", trc level: 1, release: "700"
sysno 00
sid W41
systemid 387 (Intel x86 with Linux)
relno 7000
patchlevel 0
patchno 353
intno 20050900
make: single threaded, Unicode, optimized
pid 22162
kernel runs with dp version 247000(ext=110000) (@(#) DPLIB-INT-VERSION-247000-UC)
length of sys_adm_ext is 576 bytes
*** SWITCH TRC-HIDE on ***
***LOG Q00=> DpSapEnvInit, DPStart (00 22162) [dpxxdisp.c 1345]
shared lib "dw_xml.so" version 353 successfully loaded
shared lib "dw_xtc.so" version 353 successfully loaded
shared lib "dw_stl.so" version 353 successfully loaded
shared lib "dw_gui.so" version 353 successfully loaded
shared lib "dw_mdm.so" version 353 successfully loaded
rdisp/softcancel_sequence : -> 0,5,-1
use internal message server connection to port 3900
Tue Mar 31 00:02:41 2015
*** WARNING => DpNetCheck: NiHostToAddr(www.doesnotexist0042.qqq.nxst) took 21 seconds
Tue Mar 31 00:02:52 2015
*** WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 11 seconds
***LOG GZZ=> 2 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 5540]
MtxInit: 30000 0 0
DpSysAdmExtInit: ABAP is active
DpSysAdmExtInit: VMC (JAVA VM in WP) is not active
DpIPCInit2: start server >willsys41_W41_00 <
DpShMCreate: sizeof(wp_adm) 17120 (1712)
DpShMCreate: sizeof(tm_adm) 4480000 (22288)
DpShMCreate: sizeof(wp_ca_adm) 28800 (96)
DpShMCreate: sizeof(appc_ca_adm) 9600 (96)
DpCommTableSize: max/headSize/ftSize/tableSize=500/8/524056/524064
DpShMCreate: sizeof(comm_adm) 524064 (1036)
DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=0/0/0/0/0
DpShMCreate: sizeof(slock_adm) 0 (92)
DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
DpShMCreate: sizeof(file_adm) 0 (68)
DpShMCreate: sizeof(vmc_adm) 0 (1684)
DpShMCreate: sizeof(wall_adm) (38456/34360/80/184)
DpShMCreate: sizeof(gw_adm) 48
DpShMCreate: SHM_DP_ADM_KEY (addr: 0x4ed2000, size: 5141584)
DpShMCreate: allocated sys_adm at 0x4ed2000
DpShMCreate: allocated wp_adm at 0x4ed4260
DpShMCreate: allocated tm_adm_list at 0x4ed8540
DpShMCreate: allocated tm_adm at 0x4ed8570
DpShMCreate: allocated wp_ca_adm at 0x531e170
DpShMCreate: allocated appc_ca_adm at 0x53251f0
DpShMCreate: allocated comm_adm at 0x5327770
DpShMCreate: system runs without slock table
DpShMCreate: system runs without file table
DpShMCreate: allocated vmc_adm_list at 0x53a7690
DpShMCreate: allocated gw_adm at 0x53a76d0
DpShMCreate: system runs without vmc_adm
DpShMCreate: allocated ca_info at 0x53a7700
DpShMCreate: allocated wall_adm at 0x53a7790
MBUF state OFF
DpCommInitTable: init table for 500 entries
DpRqQInit: Parameter rdisp/queue_lock_level = 2
rdisp/queue_size_check_value : -> on,50,30,40,500,50,500,80
ThTaskStatus: rdisp/reset_online_during_debug 0
EmInit: MmSetImplementation( 2 ).
MM global diagnostic options set: 0
<ES> client 0 initializing ....
<ES> EsILock: use spinlock for locking
<ES> InitFreeList
<ES> block size is 1024 kByte.
Using implementation map
<EsMap> EsMapUnamFileMapInit: Initialize the memory 240 MB
Linux: Kernel supports shared memory disclaiming
Linux: using madvise(<pointer>, <size>, 9).
Linux: disclaiming for shared memory enabled
<ES> 239 blocks reserved for free list.
ES initialized.
mm.dump: set maximum dump mem to 96 MB
Tue Mar 31 00:02:53 2015
rdisp/http_min_wait_dia_wp : 1 -> 1
***LOG CPS=> DpLoopInit, ICU ( 3.0 3.0 4.0.1) [dpxxdisp.c 1752]
***LOG Q0K=> DpMsAttach, mscon ( willsys41) [dpxxdisp.c 12953]
DpStartStopMsg: send start message (myname is >willsys41_W41_00 <)
DpStartStopMsg: start msg sent
Warning: Swap space is configured quite small with 5035 MB.
It should be two times larger than the amount of RAM (3066 MB).
See note 171356 for more information.
Warning: tmpfs at /dev/shm is configured quite small with 1532 MB!
Minimum value is 2048 MB.
Recommended size is 75 % of RAM + swap.
*** INFO Shm 13 in Pool 10 59082 KB estimated 58800 KB real ( -282 KB -72 %)
CCMS: start to initalize 3.X shared alert area (first segment).
*** ERROR => DpWPCheck: W0 (pid 22217) died (severity=0, status=65280) [dpxxdisp.c 16083]
child (pid=22217) exited with exit code 255
my types changed after wp death/restart 0xbf --> 0xbe
*** ERROR => DpWPCheck: W1 (pid 22218) died (severity=0, status=65280) [dpxxdisp.c 16083]
child (pid=22218) exited with exit code 255
*** ERROR => DpWPCheck: W2 (pid 22219) died (severity=0, status=65280) [dpxxdisp.c 16083]
child (pid=22219) exited with exit code 255
*** ERROR => DpWPCheck: W3 (pid 22220) died (severity=0, status=65280) [dpxxdisp.c 16083]
child (pid=22220) exited with exit code 255
my types changed after wp death/restart 0xbe --> 0xbc
my types changed after wp death/restart 0xbc --> 0xb8
my types changed after wp death/restart 0xb8 --> 0xb0
my types changed after wp death/restart 0xb0 --> 0xa0
my types changed after wp death/restart 0xa0 --> 0x80
*** DP_FATAL_ERROR => DpWPCheck: no more work processes
*** DISPATCHER EMERGENCY SHUTDOWN ***
increase tracelevel of WPs
NiWait: sleep (10000ms) ...
NiISelect: timeout 10000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:04 2015
NiISelect: TIMEOUT occured (10000ms)
dump system status
Workprocess Table (long) Tue Mar 31 07:03:04 2015
========================
No Ty. Pid Status Cause Start Err Sem CPU Time Program Cl User Action Table
0 DIA 22217 Ended no 1 0 0
1 DIA 22218 Ended no 1 0 0
2 DIA 22219 Ended no 1 0 0
3 DIA 22220 Ended no 1 0 0
4 UPD 22221 Ended no 1 0 0
5 ENQ 22222 Ended no 1 0 0
6 BTC 22223 Ended no 1 0 0
7 BTC 22224 Ended no 1 0 0
8 SPO 22225 Ended no 1 0 0
9 UP2 22226 Ended no 1 0 0
Dispatcher Queue Statistics Tue Mar 31 07:03:04 2015
===========================
+------+--------+--------+--------+--------+--------+
| Typ | now | high | max | writes | reads |
+------+--------+--------+--------+--------+--------+
| NOWP | 4 | 4 | 2000 | 4 | 0 |
+------+--------+--------+--------+--------+--------+
| DIA | 1 | 1 | 2000 | 1 | 0 |
+------+--------+--------+--------+--------+--------+
| UPD | 0 | 0 | 2000 | 0 | 0 |
+------+--------+--------+--------+--------+--------+
| ENQ | 0 | 0 | 2000 | 0 | 0 |
+------+--------+--------+--------+--------+--------+
| BTC | 0 | 0 | 2000 | 0 | 0 |
+------+--------+--------+--------+--------+--------+
| SPO | 0 | 0 | 2000 | 0 | 0 |
+------+--------+--------+--------+--------+--------+
| UP2 | 0 | 0 | 2000 | 0 | 0 |
+------+--------+--------+--------+--------+--------+
max_rq_id 6
wake_evt_udp_now 1
wake events total 5, udp 1 ( 20%), shm 4 ( 80%)
since last update total 5, udp 1 ( 20%), shm 4 ( 80%)
Dump of tm_adm structure: Tue Mar 31 07:03:04 2015
=========================
Term uid man user term lastop mod wp ta a/i (modes)
Workprocess Comm. Area Blocks Tue Mar 31 07:03:04 2015
=============================
Slots: 300, Used: 0, Max: 0
+------+--------------+----------+-------------+
| id | owner | pid | eyecatcher |
+------+--------------+----------+-------------+
NiWait: sleep (5000ms) ...
NiISelect: timeout 5000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:10 2015
NiISelect: TIMEOUT occured (5000ms)
DpHalt: shutdown server >willsys41_W41_00 < (normal)
DpJ2eeDisableRestart
DpModState: buffer in state MBUF_OFF
NiBufSend starting
NiIWrite: hdl 2 sent data (wrt=110,pac=1,MESG_IO)
MsINiWrite: sent 110 bytes
MsIModState: change state to SHUTDOWN
DpModState: change server state from STARTING to SHUTDOWN
Switch off Shared memory profiling
ShmProtect( 57, 3 )
ShmProtect( key 57 valid )
ShmProtect( slot Index 56 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x151f000)
ShmProtect( after shmat )
ShmProtect: shmat key 57 prot 3/0 done
ShmProtect(SHM_PROFILE, SHM_PROT_RW
ShmProtect( 57, 1 )
ShmProtect( key 57 valid )
ShmProtect( slot Index 56 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x151f000)
ShmProtect( after shmat )
ShmProtect: shmat key 57 prot 1/4096 done
ShmProtect(SHM_PROFILE, SHM_PROT_RD
DpWakeUpWps: wake up all wp's
Stop work processes
Stop gateway
killing proc (22215) (SOFT_KILL)
Stop icman
killing proc (22216) (SOFT_KILL)
Terminate gui connections
wait for end of work processes
wait for end of gateway
kill(22215,0) -> ESRCH: process died
wait for end of icman
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:11 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:12 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:13 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:14 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:15 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:16 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:17 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:18 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:19 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:20 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:21 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:23 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) -> ESRCH: process died
DpStartStopMsg: send stop message (myname is >willsys41_W41_00 <)
AdGetSelfIdentRecord: > <
AdCvtRecToExt: opcode 60 (AD_SELFIDENT), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 4 (AD_STARTSTOP), ser 0, ex 0, errno 0
DpConvertRequest: net size = 189 bytes
NiBufSend starting
NiIWrite: hdl 2 sent data (wrt=562,pac=1,MESG_IO)
MsINiWrite: sent 562 bytes
send msg (len 110+452) to name -, type 4, key -
DpStartStopMsg: stop msg sent
NiBufIAlloc: malloc NIBUF-IN, to 32110 bytes
MsIBufAlloc: allocated buffer
NiIRead: hdl 2 received data (rcd=458,pac=1,MESG_IO)
NiBufIIn: NIBUF len=458
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 458 bytes
MSG received, len 110+348, flag 4, from willsys41_W41_00 , typ 0, key FFFFFFFF00000000
DpHalt: received 348 bytes from message server
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 4 bytes from message server
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 4 bytes from message server
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 4 bytes from message server
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 4 bytes from message server
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 4 bytes from message server
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 4 bytes from message server
NiIRead: hdl 2 received data (rcd=214,pac=1,MESG_IO)
NiBufIIn: NIBUF len=214
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 214 bytes
MSG received, len 110+104, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 104 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 recv would block (errno=EAGAIN)
NiIRead: read for hdl 2 timed out (0ms)
DpHalt: no more messages from the message server
DpHalt: send keepalive to synchronize with the message server
NiBufSend starting
NiIWrite: hdl 2 sent data (wrt=114,pac=1,MESG_IO)
MsINiWrite: sent 114 bytes
send msg (len 110+4) to name MSG_SERVER, type 0, key -
MsSndName: MS_NOOP ok
Send 4 bytes to MSG_SERVER
NiIRead: hdl 2 recv would block (errno=EAGAIN)
NiIPeek: peek successful for hdl 2 (r)
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
Received 4 bytes from MSG_SERVER
Received opcode MS_NOOP from msg_server, reply MSOP_OK
MsOpReceive: ok
MsSendKeepalive : keepalive sent to message server
NiIRead: hdl 2 recv would block (errno=EAGAIN)
Tue Mar 31 00:03:24 2015
NiIPeek: peek for hdl 2 timed out (r; 1000ms)
NiIRead: read for hdl 2 timed out (1000ms)
DpHalt: no more messages from the message server
DpHalt: sync with message server o.k.
detach from message server
***LOG Q0M=> DpMsDetach, ms_detach () [dpxxdisp.c 13304]
NiBufSend starting
NiIWrite: hdl 2 sent data (wrt=110,pac=1,MESG_IO)
MsINiWrite: sent 110 bytes
MsIDetach: send logout to msg_server
MsIDetach: call exit function
DpMsShutdownHook called
NiBufISelUpdate: new MODE -- (r-) for hdl 2 in set0
SiSelPSet: set events of sock 11 to: ---
NiBufISelRemove: remove hdl 2 from set0
SiSelPRemove: removed last sock 11 (pos=3)
NiSelIRemove: removed hdl 2
NiICloseHandle: shutdown and close hdl 2 / sock 11
NiBufIClose: clear extension for hdl 2
MsIDetach: detach MS-system
cleanup EM
EsCleanup ....
EsCleanup destroy slot 0
<EsMap: unlink /SAP_ES_00_000
EmCleanup() -> 0
Es2Cleanup: Cleanup ES2
ShmCreate( 76, 0, 2, 0x0xcef3328 )
ShmKeyPermission( 76 ) = 0740 (octal)
ShmDelete( 13 )
cleanup event management
cleanup shared memory/semaphores
ShmCleanup SHM_SYS_ADM_KEY
ShmCleanup( 1 )
ShmCreate( 1, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 1, 3 )
ShmProtect( key 1 valid )
ShmProtect( slot Index 0 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x5e1000)
ShmProtect( after shmat )
ShmProtect: shmat key 1 prot 3/0 done
ShmCreate( 1, 0, 2, -> 0x0x5e1000 )
ShmCleanup SHM_DP_ADM_KEY
ShmCleanup( 2 )
ShmCreate( 2, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 2, 3 )
ShmProtect( key 2 valid )
ShmProtect( slot Index 1 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x4ed2000)
ShmProtect( after shmat )
ShmProtect: shmat key 2 prot 3/0 done
ShmCreate( 2, 0, 2, -> 0x0x4ed2000 )
ShmCleanup SHM_DP_CA_KEY
ShmCleanup( 3 )
ShmCreate( 3, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 3, 3 )
ShmProtect( key 3 valid )
ShmProtect( slot Index 2 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x1655000)
ShmProtect( after shmat )
ShmProtect: shmat key 3 prot 3/0 done
ShmCreate( 3, 0, 2, -> 0x0x1655000 )
ShmCleanup SHM_PF_KEY
ShmCleanup( 4 )
ShmCreate( 4, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 4 ) = 0740 (octal)
ShmCleanup SHM_PRES_BUF
ShmCleanup( 14 )
ShmCreate( 14, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 14 ) = 0740 (octal)
ShmCleanup SHM_CALI_BUFFER
ShmCleanup( 11 )
ShmCreate( 11, 0, 2, 0x0xbf99a5e8 )
ShmGet( 10, 11, 0, 2, 0x0xbf99a52c )
ShmCleanup SHM_DB_TBUFF
ShmCleanup( 19 )
ShmCreate( 19, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 19 ) = 0740 (octal)
ShmCleanup SHM_DB_TBUFF_P
ShmCleanup( 33 )
ShmCreate( 33, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 33 ) = 0740 (octal)
ShmCleanup SHM_DB_STBUFF
ShmCleanup( 41 )
ShmCreate( 41, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 41 ) = 0740 (octal)
ShmCleanup SHM_DB_TTBUFF
ShmCleanup( 42 )
ShmCreate( 42, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 42, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_FTBUFF
ShmCleanup( 43 )
ShmCreate( 43, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 43, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_SNTBUFF
ShmCleanup( 45 )
ShmCreate( 45, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 45, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_IRBUFF
ShmCleanup( 44 )
ShmCreate( 44, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 44, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_OBJ_BUFFER
ShmCleanup( 54 )
ShmCreate( 54, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 54 ) = 0740 (octal)
ShmCleanup SHM_DB_SYNC
ShmCleanup( 46 )
ShmCreate( 46, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 46, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_CUA_BUFFER
ShmCleanup( 47 )
ShmCreate( 47, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 47, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_OTR_BUFFER
ShmCleanup( 64 )
ShmCreate( 64, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 64 ) = 0740 (octal)
ShmCleanup SHM_DB_ESM_BUFFER
ShmCleanup( 65 )
ShmCreate( 65, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 65 ) = 0740 (octal)
ShmCleanup SHM_ROLL_AREA_KEY
ShmCleanup( 9 )
ShmCreate( 9, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 9 ) = 0740 (octal)
ShmCleanup SHM_PAGING_AREA_KEY
ShmCleanup( 8 )
ShmCreate( 8, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 8 ) = 0740 (octal)
ShmCleanup SHM_ROLL_ADM_KEY
ShmCleanup( 17 )
ShmCreate( 17, 0, 2, 0x0xbf99a5e8 )
ShmGet( 10, 17, 0, 2, 0x0xbf99a52c )
ShmCleanup SHM_PAGING_ADM_KEY
ShmCleanup( 18 )
ShmCreate( 18, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 18 ) = 0740 (octal)
ShmCleanup SHM_PXA_KEY
ShmCleanup( 6 )
ShmCreate( 6, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 6 ) = 0740 (octal)
ShmCleanup SHM_ENQ_TABLE_KEY
ShmCleanup( 34 )
ShmCreate( 34, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 34 ) = 0740 (octal)
ShmCleanup SHM_ENQID_KEY
ShmCleanup( 58 )
ShmCreate( 58, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 58 ) = 0740 (octal)
ShmCleanup SHM_VB_ADM_KEY
ShmCleanup( 7 )
ShmCreate( 7, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 7 ) = 0740 (octal)
ShmCleanup SHM_ES2_ADM
ShmCleanup( 76 )
ShmCreate( 76, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 76 ) = 0740 (octal)
ShmCleanup SHM_EM_ADM
ShmCleanup( 51 )
ShmCreate( 51, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 51, 3 )
ShmProtect( key 51 valid )
ShmProtect( slot Index 50 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x6e14000)
ShmProtect( after shmat )
ShmProtect: shmat key 51 prot 3/0 done
ShmCreate( 51, 0, 2, -> 0x0x6e14000 )
ShmCleanup SHM_EM2_ADM
ShmCleanup( 77 )
ShmCreate( 77, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 77 ) = 0740 (octal)
ShmCleanup SHM_EG2_ADM
ShmCleanup( 78 )
ShmCreate( 78, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 78 ) = 0740 (octal)
ShmCleanup SHM_MSBUF
ShmCleanup( 52 )
ShmCreate( 52, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 52, 3 )
ShmProtect( key 52 valid )
ShmProtect( slot Index 51 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x60b000)
ShmProtect( after shmat )
ShmProtect: shmat key 52 prot 3/0 done
ShmCreate( 52, 0, 2, -> 0x0x60b000 )
ShmCleanup SHM_THRUN_ADM_KEY(th run adm)
ShmCleanup( 30 )
ShmCreate( 30, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 30 ) = 0740 (octal)
ShmCleanup SHM_JAVA
ShmCleanup( 70 )
ShmCreate( 70, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 70 ) = 0740 (octal)
ShmCleanup SHM_PF_AS_KEY(Appl.Statistics)
ShmCleanup( 56 )
ShmCreate( 56, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 56 ) = 0740 (octal)
ShmCleanup SHM_PROFILE
ShmCleanup( 57 )
ShmCreate( 57, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 57, 3 )
ShmProtect( key 57 valid )
ShmProtect( slot Index 56 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x151f000)
ShmProtect( after shmat )
ShmProtect: shmat key 57 prot 3/0 done
ShmCreate( 57, 0, 2, -> 0x0x151f000 )
ShmCleanup SHM_NO_BUFFER
ShmCleanup( 48 )
ShmCreate( 48, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 48, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
removing request queue
ShmCleanup( 31 )
ShmCreate( 31, 0, 2, 0x0xbf99a5d8 )
ShmProtect( 31, 3 )
ShmProtect( key 31 valid )
ShmProtect( slot Index 30 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x573d000)
ShmProtect( after shmat )
ShmProtect: shmat key 31 prot 3/0 done
ShmCreate( 31, 0, 2, -> 0x0x573d000 )
ShmCleanup SHM_POOL_0
ShmCleanup( 10 )
ShmCreate( 10, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 10, 3 )
ShmProtect( key 10 valid )
ShmProtect( slot Index 9 )
ShmProtect( Mode: 76000000 )
ShmCreate( 10, 0, 2, -> 0x0xb3723000 )
ShmCleanup SHM_DB_POOL
ShmCleanup( 40 )
ShmCreate( 40, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_POOL_50
ShmCleanup( 50 )
ShmCreate( 50, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 50 ) = 0740 (octal)
MiCleanup:
ShmCleanup( 62 )
ShmCreate( 62, 0, 2, 0x0xbf99a5c8 )
ShmProtect( 62, 3 )
ShmProtect( key 62 valid )
ShmProtect( slot Index 61 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x8b30e000)
ShmProtect( after shmat )
ShmProtect: shmat key 62 prot 3/0 done
ShmCreate( 62, 0, 2, -> 0x0x8b30e000 )
MpiCleanup() -> 0
SemKeyPermission( 1 ) = 0740 (octal)
SemKeyPermission( 1 ) = 0740 (octal)
SemKeyPermission( 6 ) = 0740 (octal)
SemKeyPermission( 6 ) = 0740 (octal)
SemKeyPermission( 7 ) = 0740 (octal)
SemKeyPermission( 7 ) = 0740 (octal)
SemKeyPermission( 8 ) = 0740 (octal)
SemKeyPermission( 10 ) = 0740 (octal)
SemKeyPermission( 10 ) = 0740 (octal)
SemKeyPermission( 11 ) = 0740 (octal)
SemKeyPermission( 11 ) = 0740 (octal)
SemKeyPermission( 12 ) = 0740 (octal)
SemKeyPermission( 12 ) = 0740 (octal)
SemKeyPermission( 13 ) = 0740 (octal)
SemKeyPermission( 13 ) = 0740 (octal)
SemKeyPermission( 14 ) = 0740 (octal)
SemKeyPermission( 14 ) = 0740 (octal)
SemKeyPermission( 15 ) = 0740 (octal)
SemKeyPermission( 16 ) = 0740 (octal)
SemKeyPermission( 16 ) = 0740 (octal)
SemKeyPermission( 17 ) = 0740 (octal)
SemKeyPermission( 17 ) = 0740 (octal)
SemKeyPermission( 18 ) = 0740 (octal)
SemKeyPermission( 18 ) = 0740 (octal)
SemKeyPermission( 19 ) = 0740 (octal)
SemKeyPermission( 19 ) = 0740 (octal)
SemKeyPermission( 20 ) = 0740 (octal)
SemKeyPermission( 20 ) = 0740 (octal)
SemKeyPermission( 21 ) = 0740 (octal)
SemKeyPermission( 21 ) = 0740 (octal)
SemKeyPermission( 22 ) = 0740 (octal)
SemKeyPermission( 22 ) = 0740 (octal)
SemKeyPermission( 24 ) = 0740 (octal)
SemKeyPermission( 24 ) = 0740 (octal)
SemKeyPermission( 25 ) = 0740 (octal)
SemKeyPermission( 25 ) = 0740 (octal)
SemKeyPermission( 26 ) = 0740 (octal)
SemKeyPermission( 26 ) = 0740 (octal)
SemKeyPermission( 27 ) = 0740 (octal)
SemKeyPermission( 27 ) = 0740 (octal)
SemKeyPermission( 28 ) = 0740 (octal)
SemKeyPermission( 28 ) = 0740 (octal)
SemKeyPermission( 29 ) = 0740 (octal)
SemKeyPermission( 29 ) = 0740 (octal)
SemKeyPermission( 30 ) = 0740 (octal)
SemKeyPermission( 30 ) = 0740 (octal)
SemKeyPermission( 31 ) = 0740 (octal)
SemKeyPermission( 31 ) = 0740 (octal)
SemKeyPermission( 35 ) = 0740 (octal)
SemKeyPermission( 35 ) = 0740 (octal)
SemKeyPermission( 36 ) = 0740 (octal)
SemKeyPermission( 37 ) = 0740 (octal)
SemKeyPermission( 42 ) = 0740 (octal)
SemKeyPermission( 42 ) = 0740 (octal)
SemKeyPermission( 43 ) = 0740 (octal)
SemKeyPermission( 43 ) = 0740 (octal)
SemKeyPermission( 44 ) = 0740 (octal)
SemKeyPermission( 44 ) = 0740 (octal)
SemKeyPermission( 45 ) = 0740 (octal)
SemKeyPermission( 47 ) = 0740 (octal)
SemKeyPermission( 47 ) = 0740 (octal)
SemKeyPermission( 48 ) = 0740 (octal)
SemKeyPermission( 48 ) = 0740 (octal)
SemKeyPermission( 49 ) = 0740 (octal)
SemKeyPermission( 49 ) = 0740 (octal)
SemKeyPermission( 50 ) = 0740 (octal)
SemKeyPermission( 51 ) = 0740 (octal)
SemKeyPermission( 51 ) = 0740 (octal)
SemKeyPermission( 53 ) = 0740 (octal)
SemKeyPermission( 53 ) = 0740 (octal)
SemKeyPermission( 54 ) = 0740 (octal)
SemKeyPermission( 54 ) = 0740 (octal)
SemKeyPermission( 55 ) = 0740 (octal)
SemKeyPermission( 55 ) = 0740 (octal)
SemKeyPermission( 56 ) = 0740 (octal)
SemKeyPermission( 56 ) = 0740 (octal)
SemKeyPermission( 57 ) = 0740 (octal)
SemKeyPermission( 57 ) = 0740 (octal)
SemKeyPermission( 58 ) = 0740 (octal)
SemKeyPermission( 58 ) = 0740 (octal)
SemKeyPermission( 59 ) = 0740 (octal)
SemKeyPermission( 62 ) = 0740 (octal)
SemKeyPermission( 63 ) = 0740 (octal)
SemKeyPermission( 64 ) = 0740 (octal)
SemKeyPermission( 65 ) = 0740 (octal)
SemKeyPermission( 66 ) = 0740 (octal)
SemKeyPermission( 67 ) = 0740 (octal)
SemKeyPermission( 69 ) = 0740 (octal)
SemKeyPermission( 69 ) = 0740 (octal)
SemKeyPermission( 70 ) = 0740 (octal)
SemKeyPermission( 72 ) = 0740 (octal)
removing Semaphore-Management
closing connect handles (dgm + tcp)
DpDelSocketInfo: del info for socket 0 (type=2)
NiICloseHandle: shutdown and close hdl 0 / sock 8
DpDelSocketInfo: del info for socket 1 (type=1)
NiICloseHandle: shutdown and close hdl 1 / sock 9 - sock 10
***LOG Q05=> DpHalt, DPStop ( 22162) [dpxxdisp.c 11739]
*** shutdown completed - server stopped ***
Thanks in advance....
Regards,
Sundar -
My airport express can't locate a dns server
I am unable to connect to the Internet, with my Mac,iPad or iPhone, even with the light green. I used my airport utility and it can't find a Dns server.
I called my Internet provider and they said everything looked alright on there end.
Does any body know what it might be?I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref:Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results. -
Hi Alll, I am a student of Nagpur University, India and much intersted in Solaris OS.... Can anybody mail me complete steps of configuration of DNS ???? my id is [email protected]
ThanksCould this be of some help?
http://www.google.com/search?hl=en&q=solaris+%2B+dns&btnG=Google+Search -
Can't find my DNS Primary and Secondary
Dear God, I need my DNS primary and secondary. I'm trying to set my xbox 360 up with it's own ip ect. I've gone to my airport to get this information but my DNS is the same as the IPv4 router. My xbox requires a DNS primary and secondary. The only thing I can find for my DNS is a Domain Name and Server address: 10.0.1.1 Do I put this number in my xbox for the DNS with no secondary?
I think your router is not configured properly for your internet connection. Router is not giving out a valid DNS to the computers because it cannot obtain it (dns) from the modem. Is your connection Cable or DSL?
-
DNS Issues, can't set static DNS server
I have an Airport Extreme (which I'll call the router). It has an IPv6 tunnel (to Hurricane Electric), so it hands out IPv4 DHCP and announces an IPv6 network as well. The DNS servers configured on the router are OpenDNS'.
My Apple TV 2 is connected via wired Ethernet to the router. It was using a DHCP address provided by the router, which made the DNS server the same address as the router. I wanted to manually set the DNS to use my ISP's, so that I can make sure the Netflix streaming issue I have is not a DNS issue.
So I changed the Apple TV to a manual address, and set the DNS server to my ISP's DNS server (Apple TV can only have one DNS server? Odd.)
After I save this, the Network page shows the correct manual IP, mask, and router, but the DNS Address is an IPv6 address (one that belongs to my network, but the entire address isn't visible), not the one I set. When I Configure TCP/IP again, and I reach the DNS Address page, the first digit of the existing address is "20", and the rest of the digits are "0". Interesting note as well: if I press Down, the number will increment to 19, and so on, but if I press Up, it changes to 0. Obviously the UI isn't designed for IPv6 addressing, but there's an IPv6 address in there nevertheless.
Screenshots:
http://www.flickr.com/photos/random_robin/5310011344/
http://www.flickr.com/photos/random_robin/5310016288/
I have tried to set the DNS Address multiple times now, and have restarted the Apple TV. The IPv6 DNS Address persists.After 16 hours of working i don´t have seen this easy solution. I had tried with Internet Explorer and Opera but finaly i have need to use Firefox.
Thanks a lot to solve it. -
I asked at a Hong Kong apple shop if they had password protected external drives. They didn't, I bought one anyway.
I'm wondering can I configure this drive. If yes, what do I need to do?This looks like the easiest and most direct method and since it uses Disk Utility it would work on any OS.
http://osxdaily.com/2012/01/25/password-protect-external-drive-mac-encrypted-par tition/ -
please help!! how can i configure my iphone 3gs because i've been updated a new version, i did it but it's hard to activate it again. this message i always recieved in my iphone
"We're sorry, we are unable to continue with your activation at this time."You phone was hacked. You can not get help with it here. Hacking / Jailbreaking voids any warraty and forfeits your right to support. Discussing jailbroken / hacked devices is forbidden by the terms of service here.
-
With an 11"-inch Macbook Air (mid-2012) using a mini DisplayPort-to-VGA adapter plugged into the Thunderbolt port:
Can you configure an extended desktop with an external monitor (20") displaying full portrait mode (1200 x 1600 resolution) and keep the built-in display in landscape?
I'd like to see something like
External monitor / Built-in displayYes, I can't see why not.
Just give it a try and report back if you have a problem. -
How can I configure iCloud so it doesn't restore deleted or moved emails on my Mac?
I moved to iCloud, and so far it looks like everything is where it's supposed to be. My question is about syncing. When I delete an email on my Mac, iCloud restores it. How can I configure iCloud so that changes I make on my Mac and my iPhone stay changed?
On the Mac in System Preferences > iCloud
Make sure Mail & Notes is selected.
ON the iPhone tap Settings > iCloud
Make sure Mail is switched on.
And try restarting your Mac and iPhone. -
How can I configure my new Mac Pro to output the timeline via HDMI
How can I configure my new Mac Pro to output the timeline in FCP 7 (yes, I have X, but I'm using 7 right now). I have two monitors running from TB2, but want to have the third for a client monitor.
If I use all three via TB2, it's literally three monitors, and I want to edit on my CineDisplay. I only want the client to see the timeline video on the third monitor. When I hook up HDMI I get no signal, in fact, I can't have the HDMI cable hooked up for TB2 to work with the third.
Thanks,
GEvans
DarthPro
3.7 QCIntelXeonE5
12 GB
AMD FirePro dual D300 2048MB
OSX 10.9.2If you use all ThunderBolt displays, or stick with DisplayPort and Mini DisplayPort (free conversion between the two with only a cheap cable) you can have up to six displays.
If you attach "legacy" displays with "any-old adapter", you can have up to two, and the built-in HDMI counts as one if you use it.
Any more requires ACTIVE Adapters.
The US$100 Apple ACTIVE Mini DisplayPort to Dual-Link DVI adapter works in every case, even displays over 1920 wide.
StarTech and Accell make US$35 ACTIVE adpters that work for displays up to 1920 wide. -
HT4356 How can I configure the printer to print only grey tones from my iPad 2? Printer=Hp6520
How can I configure printer with iPad to print only grey tones? This works fine from my laptop - not air printing from that one though. I can't find anywhere on the iPad how to do printer settings and this also seems not to be available as an option when doing a printout. In fact, no options seem to be available. Thanks in advance for reacting!
HermiThere is currently no option for this. You can give Apple feedback here:
http://www.apple.com/feedback/ipad.html -
According to William Stanek, in his Windows Server 2012 R2 Inside Out: Configuration, Storage & Essentials book, this is apparently possible: (pg. 615 - here it is on Google Books: https://books.google.ca/books?id=0IyfBAAAQBAJ&pg=PT819&lpg=PT819&dq=read+operation )
Integrity can be enabled when the system is not running on Storage Spaces. When
integrity is enabled and ReFS detects a checksum mismatch, ReFS logs an event and
fails the read operation by default. If you don’t want the read operation to fail, you
can configure ReFS to continue with the read operation. A related event will be logged
regardless.
So then how do I configure it to do that???
(And just to make it super-clear, I'm NOT using Storage Spaces, so there is no redundancy via mirroring/parity, and I'm not expecting any file repair - just detection of corruption. It's just a basic volume formatted with ReFS and
with integrity streams enabled, via format E: /fs:ReFS /i:enabled
For those who want more details, here's the situation:
I try to perform a read operation on a file with corrupted data (purposely done for testing using a low-level disk editor), I get a the following error message:
And an event ID 133 from ReFSv1 gets logged in the System log:
Clicking "Try Again" just brings up the same message, and clicking "Skip" skips the operation entirely.
This is indeed the correct default behaviour.
What I want instead is for the read operation to be allowed to complete, with corrupt data and all, and ONLY for the event to be logged. And according to William Stanek, this is supposed to be configurable somewhere - and after hours of searching, I haven't
been able to find anything.Hi Tommy,
>>How can I configure ReFS to NOT fail read operations when a checksum error is detected
We can use PowerShell command Set-FileIntegrity to configure this. The specific parameter for controlling this behavior is
-Enforce <Boolean>which indicates whether to enable blocking access to a file if integrity streams do not match the data.
Regarding this point, the following article can be referred to as reference.
Set-FileIntegrity
https://technet.microsoft.com/en-us/library/jj218351.aspx
Best regards,
Frank Shen
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] -
Can't configure wireless settings on P1102w using a mac
Hi there. I can't configure wireless settings on P1102w using a mac. I have it installed with USB just fine but I want to use eprint (with ios airplay). I run the setup utility looking for some wireless setup option, but it never appears. When I finish the install it tells me to go to the eprint website to download eprint. At that site it has me download the firmware update, which I do, and then at the end of that it tells me to go to the eprint website again, which then downloads the firmware update again. It's an endless loop.
I know I need to get to the built in web server but the config page tells me I don't have an IP address. Which makes sense to me because it hasn't been set up. I can't for the life of me find how to set up the wireless using the driver software on the Mac OS. I try to follow the manuals instructions, but it looks like it is designed for windows users, and the buttons it tells me to look for just don't exist on the mac HP driver software.
Can you help?Hi,
The Wireless configuration should be made by using the EWS page, which also accessible from Mac OS over a USB connection through the printer setup.
You may find the steps listed below:
Click the Apple icon, then clickSystem Preferences.
Click Print & Fax.
Select your printer and click Open Print Queue.
Click on Printer Setup
Then select Utility
Click Open Printer Utility
Click HTMLConfig. The EWS opens.
Click the Networking tab
Then click Wireless from the list on the left
Under Communication Mode, click Infrastructure, select your network SSID from the Available Network Names (SSID) list, and then click the << button.
From the Security Mode pop-up menu under Authentication, click WEP or WPA/WPA2. Your selection depends on which Wireless Security Protocol your network uses.
Type your WEP/WPA/WPA2 key in the appropriate field, and then click Apply.
In the confirmation box, click OK and then close the HTML Config and Print Queue windows.
Once done, allow 3 minutes to fully establish the connection, then unplug the USB.
Enter Print & Fax and remove the existing USB Print Queue.
Click the Plus button and add the printer over the network.
Please let me know of any issue,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution -
Proper Configuration of DNS server for our new branch office
Hi All,
Our new office will setup a new branch office with a routed network link to our HO. In HO, we have 2 domain controllers configured as AD and DNS just for fail over scenarios.
How will we configure the DNS server of our 3rd domain controller which we will placed in the new branch office. What would be the proper settings of DNS server integrated to AD to work well especially to have a successful replication and communication to
the 2 DC's located in HO?Hi,
If you have multiple DC's in that site i would recommend using any of the partner DC's IP addresses as preferred one and secondary DNS IP to pointing to itself. Dont use loopback addresses configure it with actual IP addresses.
If you have only one server in branch office point itself as the primary DNS and HO DC as secondary and tertiary.
Make sure that all clients in your branch site are pointing to the branch DC as primary DNS server.
Regards,
Rafic
If you found this post helpful, please give it a "Helpful" vote.
If it answered your question, remember to mark it as an "Answer".
This posting is provided "AS IS" with no warranties and confers no rights! Always test ANY suggestion in a test environment before implementing!
Maybe you are looking for
-
Animated GIF--Quality and File Size
I'm having a hard time getting a quality image and a decent file size. Even if I save animated GIFs and open with PE an try to resave them, the motion is choppy and the file size is more than double the original. For example, the following image is l
-
Problems converting pdf to Word in Acrobat X Standard
I am not able to convert pdf docs into Word using acrobat x. I have tried running OCR before attempting the converstion but that does not help. It goes all the way through allowing me to save the document as a docx but then I get the message "Save
-
We used to get, when clicking on Mozilla, a simple box (Google) with a space to put the subject you wanted searched. Simple and uncluttered. I went to Mozilla because of this, as Internet Explorer was messy and cluttered. Imagine my dismay when I fin
-
guys, i have to get last 3 char. of the char. string. now the problem is, the char. string is all different length. if it was the same i could use SUBSTRING formula. but in my case its all diff. and i have to get last 3 char. from the string . what s
-
Drawing an organizational chart .
I've never done any 2d work in java before but my program needs to be able to draw organizational charts. The user does not need to be able to draw their own charts. I can't find any examples of this all I can find is bar graphs and pie charts. This