LMS4.2.2 home page load very slow

                   Hi,
I migrated from windows LMS3.2.1 to soft appliance 4.2.2. i also set the gs.properties attribute to false. but, still the home page loads very slow. let me know if somebody experienced this and fond a resolution.
thanks,
Kerim

You're not the only one with this problem. There is a long discussion, with some proposed solutions, in this thread (and searching for "slow" in the Pages forum will bring up other threads as well).

Similar Messages

  • Boot and page load very slow after 2nd HD install

    Good morning.
    I recently added a second slave HD (80 GB with a OS X partition) to my beige G3 MT. I am using the original 9 GB drive as the boot drive. Northing else was changed.
    Since that time, the boot time has increased significantly (2-3X pre 2nd drive).
    Also, page load times have been increased with the Norton AntiVirus symbol being displayed.
    1. What's causing the slow boot? Is the CPU looking at the new drive and applying Norton before the original boot drive?
    2. Are there settings in Norton that might help?
    3. Is it even worth continuing Norton use for this OS 9.1 machine?
    Thanks for your time!

    Hi, Bruce. NAV is probably scanning the entire new drive at startup, thus accounting for the major startup slowdown. And no, there's no good reason to have NAV installed at all. Your Mac doesn't need antivirus protection.

  • Why is web page loading very slow from microsoft Outlook hot links

    Clicking on any hot link embedded in an Outlook email takes from 45-60 seconds to load. If I cut and paste the same link, loading is almost instantaneous. Are there settings I can adjust? IE8 used to be somewhat slow sometimes but never this slow with Outlook links.

    What can I do to help this situation?
    I've got fresh copies of OSX running on the macs that I mentioned, and I haven't specified any dns settings in the connection properties. I don't think dns has been specified on the windows machines either.
    A DNS server has been specified on the router. Should I try removing this ip address and let the router look for it's own dns server?

  • Loading Page is very slow. Thread dump show "BuildCookie"

    Hello, Folks,
    I am developing a portal project, which have some pages and books. I find that my page is loaded very slow and I took three times thread dump, the following is the detail of thread dump. Could someone give me some hints that can help me to figure out what needs to be corrected in my code or design?
    "ExecuteThread: '14' for queue: 'default'" daemon prio=5 tid=0x03bf5190 nid=0xe2
    c runnable [44ce000..44cfd90]
    at java.io.WinNTFileSystem.list(Native Method)
    at java.io.File.list(File.java:915)
    at java.io.File.listFiles(File.java:993)
    at com.bea.wlw.runtime.core.dispatcher.AppManager.isExternalBuildCookieV
    alid(AppManager.java:1080)
    at com.bea.wlw.runtime.core.dispatcher.AppManager.validateExternalBuildC
    ookie(AppManager.java:1137)
    at com.bea.wlw.runtime.core.dispatcher.AppManager.ensureAppDeployment(Ap
    pManager.java:655)
    at com.bea.wlw.runtime.core.dispatcher.AppManager.ensureAppDeployment(Ap
    pManager.java:575)
    at jsp_servlet._framework._skeletons._default.__book._jspService(book.js
    p:12)
    at weblogic.servlet.jsp.JspBase.service(JspBase.java:33)
    at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run
    (ServletStubImpl.java:1072)
    at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubIm
    pl.java:465)
    at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubIm
    pl.java:348)
    at weblogic.servlet.internal.RequestDispatcherImpl.include(RequestDispat
    cherImpl.java:638)
    at weblogic.servlet.internal.RequestDispatcherImpl.include(RequestDispat
    cherImpl.java:423)
    at com.bea.netuix.servlets.controls.JspRenderer.renderAlt(JspRenderer.ja
    va:194)
    at com.bea.netuix.servlets.controls.JspRenderer.endRender(JspRenderer.ja
    va:142)
    at com.bea.netuix.nf.ControlLifecycle$1.postVisit(ControlLifecycle.java:
    538)
    at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
    lker.java:564)
    at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
    lker.java:553)
    at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
    lker.java:553)
    at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
    lker.java:553)
    at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
    lker.java:553)
    at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
    lker.java:553)
    at com.bea.netuix.nf.ControlTreeWalker.walkRecursiveRender(ControlTreeWa
    lker.java:553)
    at com.bea.netuix.nf.ControlTreeWalker.walk(ControlTreeWalker.java:247)
    at com.bea.netuix.nf.Lifecycle.runOutbound(Lifecycle.java:204)
    at com.bea.netuix.nf.Lifecycle.run(Lifecycle.java:146)
    at com.bea.netuix.servlets.manager.UIServlet.runLifecycle(UIServlet.java
    :333)
    at com.bea.netuix.servlets.manager.UIServlet.doPost(UIServlet.java:196)
    at com.bea.netuix.servlets.manager.PortalServlet.doPost(PortalServlet.ja
    va:772)
    at com.bea.netuix.servlets.manager.PortalServlet.doGet(PortalServlet.jav
    a:671)
    at com.bea.netuix.servlets.manager.UIServlet.service(UIServlet.java:147)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
    at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run
    (ServletStubImpl.java:1072)
    at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubIm
    pl.java:465)
    at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:28)
    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.ja
    va:27)
    at com.bea.p13n.servlets.PortalServletFilter.doFilter(PortalServletFilte
    r.java:293)
    at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.ja
    va:27)
    at weblogic.servlet.internal.WebAppServletContext$ServletInvocationActio
    n.run(WebAppServletContext.java:6987)
    at weblogic.security.acl.internal.AuthenticatedSubject.doAs(Authenticate
    dSubject.java:321)
    at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:
    121)
    at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppSe
    rvletContext.java:3892)
    at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestIm
    pl.java:2766)
    at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:224)
    at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:183)

    The page is slow because of the VO query.. I have tuned the query... Now its faster....

  • First Page Loads very slowly

    Hi
    I've been using my MacBook on my wireless connection for a while with no problems.
    Suddenly everything goes bad. My ISP ( ADSL+2 ) and Netgear ( WGT624 wireless router ) get me up and running again BUT when I load the first page of a web site it takes ages to load. From then on the pages linked to that home page load quickly.
    If i connect directly to the modem all pages load quickly.
    Netgear seem to have exhausted their options eg reducing MTU, changing channel, resetting the router etc but the first page still takes an age to load.
    Any advice gratefully received..
    thanks Colin

    Hi,
    Your question is very vague. There could be many reasons why the app would be slow in performance (your queries might be slow / memory would be less etc.).
    Check out this guide and tune your application accordingly.
    http://download.oracle.com/docs/cd/E14571_01/core.1111/e10108/adf.htm
    -Arun

  • Home page loading takes longer in a JSF

    My application takes a little longer to load its home page when a user try to access the site. This delay in getting the home page loaded for the
    first time happens to each user accessing the site. So we thought it would be the session scoped managed beans that we use in our application causing
    the issue. But we checked the session scoped bean, which are not doing any particular job to slow down the process. Then we placed a phaselistener and
    got the following printed in console. Doesent it shows that the request for home page goes twice through the JSF life cycle? Is it this that slows down
    the home page access for the first time. If so why should it go through the life cycle twice?
    14:06:45,359 INFO [Engine] BEFORE - RESTORE_VIEW 1
    14:06:45,421 INFO [Engine] AFTER - RESTORE_VIEW 1
    14:06:45,484 INFO [Engine] BEFORE - RENDER_RESPONSE 6
    14:06:47,437 INFO [STDOUT] <- Song List in Memory -> starting
    14:06:47,484 INFO [STDOUT] ################## INITIALIZING ALL URLS FOR ARTIST SEARCH ###########################..
    14:06:48,906 INFO [STDOUT] Processing ALL URLS FOR ARTIST SEARCH
    14:06:50,328 INFO [Engine] AFTER - RENDER_RESPONSE 6
    14:06:50,562 INFO [Engine] BEFORE - RESTORE_VIEW 1
    14:06:50,562 INFO [Engine] AFTER - RESTORE_VIEW 1
    14:06:50,562 INFO [Engine] BEFORE - RENDER_RESPONSE 6
    14:06:50,609 INFO [Engine] AFTER - RENDER_RESPONSE 6
    I'm new to JSF and has to support an application developed in JSF. Any inputs on this is appreciated.
    Thanks in advance.

    download google chrome,  I bet you it will open faster.   probably just an IE thing. 

  • Please help: Course loads very slow and takes almost 100% cpu and 1.08 GB memory

    The total page number is 129. We used Captivate 5.5. We have several Webpage widgets and a few videos. I tried to take out the web widgets and the videos, however, the course still loads very slow.
    I would really appreciate if someone can give somve suggestion.
    Thank you very much.

    Captain Ibuprofen, we actually continued having the slowness problem in the past week. Then one of our developers found out the reason: as same as yours, caused by the page number widget. I wish we would have seen your response earlier. But yeah, so now we took out the page number widget and everything goes normal.
    Also thanks for the tips on using the cpInfoCurrentSlide variable when adding the slide number. Thanks Andy.

  • WRT350n Firmware Update 1.03.7 - Web page load really slow after update

    Well I updated my WRT350N with the new firmware, but now web pages load very slowly, and streaming video is even slower. Before the update it was blazing fast. I run a mixed network of wireless N and G. Both Wireless N connections connect at 200 or higher Mbps now, which is a great improvement.
    Anybody got any ideas why web pages and steaming video run so slow now.
    Also downloading files never goes above 30 kb/sec now.
    I use comcast cable and downloads were so fast before.
    Thanks in advance.

    check the download speed and the streaming video when the computer is directly connected to the modem

  • IBooks Author: in exported file, one page loads very slowly...

    iBooks Author: in exported file, one page loads very slowly and drags when scrolling through pages, almost stopping the scroll.  I have never seen this problem before with photo pages.  Normally they scroll just as smoothly as text pages.
    I have tried rebuilding the page with more compressed files to no avail.  The image files used on the page are not any bigger than others I have used previously without any problem.
    I have tried restarting my iBook.
    I am using a template that I have modified quite a bit.  The templates currently offered by Apple and third parties are not even close to what I am looking for in terms of layout, so I have to rip almost everything out of the page and start with a blank page, most of the time.  I tried modyfying the layouts to save time and then saved as a new template.  Apple really needs to add a module to create your own template at the beginning of a project.  Or they need to create one very open template, without much on the pages.

    I finally solved the problem by using an unmodified template. I would still like to know how my modifications to the other template caused the problem, but for now it remains a mystery.  Thanks for your ideas.
    Next I will try modifying the template without saving it as a template (merely saving it as a file) to see if I can get away with my modifications.  Also I will make fewer modifications.
    Slowly but surely I am learning this program by trial and error.  Each time I try a few formatting variations, output an iBooks file, and open it on my iPad.  I have probably done 20 of these tests, so far.  Once I work out every detail of the design and structure, I will build the final book.  I am lucky to have a beautiful PDF of the hardcover version, generously provided by my publisher.  This not only sets a high bar for me, but also allows me to use some of their design elements via screen capture.
    iBooks Author has great potential, but I along way to go to get there. One feature I would really like to see in the next update: the ability to add a hidden caption to a photo.  The reader would tap the image and the caption would appear. Tap again and it disappears.

  • Application ADF load very slow

    Dear all.
    My team build a backup server for oracle portal and oracle center content version 11.1.1.6.
    I restored UCM server normal, configuration and index.
    But application load very slow, 2 minutes. In original server is 15 second.
    I see log when i restore error in index. Indexing database too slow 4-5h.
    I expdp normal with no error
    Does anyone kind to help me to solve this? Thanks in advance for any help or suggestion.

    I use iSquint to compress the video. Have a look at this site to see my dv project that was 286mb original size, compressed down to 4.8mb. http://web.mac.com/lfairlie/iWeb/Site%204/Welcome.html
    You can play with the size it compresses to quality wise as well.
    Message was edited by: lynnie61

  • UIX page run very slow on Jboss

    hi.. i am using Jdeveloper 10.1.2 to develop my application and my application containing JSP and UIX pages.At last i deploy it onto Jboss 3.2.7.
    It work properly, but i found that each time user access/open a page, which never open before, that page(either UIX or JSP page) show very slow. After that when user open it again, it show out as normal.
    Now, the problem is, when user close the browser, open it and access that page again, for JSP, it show out fast, but for UIX, it still take time to show out. I dont know what cause this happen. And i wondering that is that any way to configure ADF UIX in order to increase its performance?
    Please give me some suggestions and guides. Thanks in advance.

    Hi... is there anybody can help me? thanks..

  • ITunes loads very slow

    With over 48000 songs, itunes loads very slow. Thinking it my be my pc I loaded it onto a new pc and get the same results. Is there anything I can do to getit to load under 5 seconds at least?

    Dear Apple,
    I need to complain about the same problem. I have 1/10th the songs in i-Tunes (~4800) and I cringe every time I want to start the program. The same delay happens anytime I load or switch a CD to import a song.
    Google can load a billion links in a blink; can't you load a millionth of this info in the same amount of time? Any hints would be greatly appreciated.
    Frustrated,
    -Mike

  • WIFI too slow after IOS 6 installed. SAFARI is loading very slow for burmese language website. Please help.....

    WIFI too slow after IOS 6 installed. SAFARI is loading very slow for burmese language websites. Not only that....many other websites too.....Please help.....Don't expect that ENglish is only language we expect to view on IPAD......
    Most websites are responding very slow with safari & many other broswers opera.........Too annoying IOS 6...Give me IOS 5 back...Tell me how.....
    I am too angry with IOS 6.......My IPAD 2 & IPHONE 4S all suck after installing IOS 6..........
    I can't believe "$600 billions " company released without testing on every devices with different wifi routers, applications on their store.........   
    Give me some ways to downgrade to IOS 5.1.1......

    iOS 6 Wifi Problems/Fixes
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    You may think you are connected to the internet, but maybe not. Click on Safari and see if it connects.
    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting
    http://www.apple.com/support/ipad/wifi/
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Web pages are very slow to load airport is fine and other users do not have any problems

    my macbook pro is very slow to load web pages airport is running fine and other users do not have any issues?

    Likely a corrupted cache, do #12 and #13 here, if that doesn't work run through the Steps 1+
    Step by Step to fix your Mac
    Why is my computer slow?

  • APEX  all page loads very very slow - Default install with  11G R1

    HI,
    I have installed Oracle 11g R2 on my Windows XP desktop. APEX is installed by default in 11G R2. I have tried to use APEX but it runs very slow. For example, bringing up the Oracle APEX admin login page takes to 5 to 7 minutes. Once logged in, performing admin tasks is painfully slow as well.
    EM is fast, the pages come up in a few seconds. I am not sure of the exact setup APEX since it is installed by default.
    Here is what I have tried so far
    1) localhost:8080/{I can not remember the rest of the url}
    2) ip/8080/
    3) tried both IE 6 and firefox.
    4) turned off the proxy server in IE options. We are on a LAN and use proxy to internet
    I ran a search for a dads file on oracle home, but I can not find it. Maybe it is renamed in 11G r2.
    Any help would be appreciated.
    Edited by: solvetek on May 2, 2009 7:53 AM

    Hello,
    Check the value of SHARED_SERVERS, if it's set low (which it probably will be if you haven't adjusted it yourself), then you'll probably want to increase the value.
    Essentially (if this is your issue) there are insufficient pooled connections available to service all the HTTP connections necessary to render your page, so you're paying a performance penalty waiting for either new connections to fire up, or for busy connections to be free'd up ready to service a new request.
    Hope this helps,
    John.
    Blog: http://jes.blogs.shellprompt.net
    Work: http://www.apex-evangelists.com
    Author of Pro Application Express: http://tinyurl.com/3gu7cd
    REWARDS: Please remember to mark helpful or correct posts on the forum, not just for my answers but for everyone!

Maybe you are looking for