Load balancing URL setup for planning application 11.1.2.1

Hi Gurus,
There is an existing planning environment with Weblogic/ Oracle HTTP load balancing setup. I just would like to know where would exactly be the generic/ common URL (the URL without actual servername) configured for planning and SmartView?
Is there any properties file (weblogic/ HTTP) where we will mention those details?
Thanks,
Siva

I am not sure I get what you are asking but planning can be accessed through workspace or by
http://<ohs_server>:19000/HyperionPlanning
and Smart View http://<ohs_server>:19000/workspace/SmartViewProviders
If you want to understand about the configuration you can run a registry report.
Cheers
John

Similar Messages

  • Site not found using Sharepoint Designer 2013, Load balance URL and the Front end servers.

    Dears,
    My SharePoint farm is with the below configuration in our office :
    Batch processing server the with Central Administration
    Web Front End Sever 1 (http://wfe01)
    Web Front End Sever 2 (http://wfe02)
    I do have the load balance URL as http://finance.mycompany.com and as per the system administrator it seems configured properly.
    In AAM i have mapped the URLs as below for the web application in Central Administration portal:
    http://finance.mycompany.com - Default Zone
    http://wfe01 - Intranet Zone
    http://wfe02 - Internet Zone
    I was able to browse the site via the load balance URL : http://finance.mycompany.com, but couldn't open the site using the Share Point Designer 2013. It always says the site not found.
    please advise,
    thanks,
    Ammar

    What do the wfe01 and wfe02 aams do?
    Are you browsing to the SharePoint site and using SPD on the same computer, is it part of the farm or a seperate client computer?
    thanks Alex a lot for your response and appreciate the same.
    WFE01, WFE01 is connected to the one central admin on Batch Processing Server (central admin URL is http://SharepointCA:5555 and the SharePoint Web Application is hosted under port 80 on the same server). So the AAM configured on the batch processing server
    central admin.
    I can connect to the site using the SPD inside the Batch Processing server if i mention the site urs as http://localhost. But not from other client computers by putting the load balance URL - http://finance.mycompany.com.
    I can browse the sites directly putting http://wfe01, http://wfe02 and as well as the load balance URL (http://finance.mycompany.com). The custom webparts are getting crashed when i put the web application URL as http://finance.mycompany.com.
    thanks,
    Ammar

  • Network Load Balancing and failover for AFP Sharing

    Dear all,
    Somebody kindly teach me to use round robin DNS to perform the network load balancing, it's success but not the failover.
    I have 4 xserve and want to do the load balancing and failover at the same time.
    I have read the IP failover document and setup it successfully, but anyone know is it possible to do the IP failover for more than 2 server?
    For example, 4 server serving the AFP service at the same time, maybe I have 1 more extra server to do the IP failover for thoese 4 servers.
    As I know, IP failover require Firewire as the heartbeat detection. But one xserve only have 2 firewire ports. May I setting up the IP failover only by a ethernet port and an IP address? does it possible to detect and failover to any server after server down has been detected?
    I believe load balancer maybe the best solution but its cost is too high.
    Thanks any advance!
    Karllee

    well, u have 2 options here
    software load balancing
    request comes it foo.com -> ws7u2 hosting foo.com is configured to run as reverse proxy . this server sends any incoming requests to one of the four back end web server 7 handling your incoming request
    hardware load balancing (this you need to invest)
    request comes to hardware load balancer who responds for foo.com -> sends requests to four ws7 server hosting your application
    you could try out how software load balancing works out for you before you invest in hardware load balancing
    here is more instruction on configuring ws7 + reverse proxy (software load configuration)
    - install ws7 on foo.com
    - create a new configuration (choose port 80, disable java

  • Office Web Apps Load Balancing Configuration Issue for SharePoint 2013

    I have load balanced servers dedicated for Office Web Apps with name “md1xxxwfe1” and “md1xxxwfe2” 
    , both this servers are load balanced by CISCO Load balancer. And I have mapped Load Balancer Virutal IP with host name officeapps.jda.corp.local in the DNS records.
     Things are working fine if I add new farm by using New-OfficeWebAppsFarm
     with server name as internalurl in PowerShell console
     as like “  -internalurl http://
    md1xxxwfe1  but when I use –internalurl officeapps.jda.corp.local it is not working at all. I’m not getting what to do at this point.
    I have gone through following blogs but no luck.
    http://blogs.technet.com/b/meamcs/archive/2013/03/27/office-web-apps-2013-multi-servers-nlb-installation-and-deployment-for-sharepoint-2013-step-by-step-guide.aspx
    http://blogs.technet.com/b/office_resource_kit/archive/2012/09/11/introducing-office-web-apps-server.aspx
    http://davidlimsharepoint.blogspot.in/2013/02/installing-and-configuring-office-web.html 
    http://sps2013.blogspot.in/2013/09/office-web-apps-with-sharepoint-2013.html
    The output of the wfe1 server is attached with this. When I open http:// /hosting/discovery in wfe1 I’m getting following result (attached
    screenshot) but it should show hostname rather than server name.
    Please help me
    Thanks, Ram Ch

    Hi  Ram ,
    For  troubleshooting your issue, please take steps as below:
    Just about any load balancing solution will work, including a server that runs the Web Server (IIS) role running Application Request Routing (ARR):Install
    Application Request Routing
    Install the certificate on the load balancer as described under Securing Office Web Apps Server communications by using
    HTTPS.
    Make sure you have configured the cluster correctly for full internet name:
    Reference:
    http://technet.microsoft.com/en-us/library/jj219435.aspx#loadbalancer
    Thanks,
    Eric
    Forum Support
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support,
    contact [email protected]
    Eric Tao
    TechNet Community Support

  • Load balancing and HA for persistence chat pool

    Hi,
           I have 12000 users for lync 2013 . plan to have 2 persistence chat servers in a pool , have below queries regarding the same.
    1. which type of load balancing will work for persistence chat pool.... DNS or HLB?  if its HLB then is it mandatory to use HLB , agenda is to minimize the cost.
    2. there is already 2 HLB for FE pool , one for external service and 1 for internal service.... can i use the same HLB for persistence chat pool?
    3. does persistence chat pool have HA bydefault like FE and Edge pool?

    1) DNS LB is fine: You can see them doing it here:http://technet.microsoft.com/en-us/library/jj205391.aspx
    2) I suppose you could, but I'd suggest sticking with DNS as it's easy, supported, and it works. 
    3) Yes.  I believe so.
    Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
    SWC Unified Communications

  • Load username and password for external application?

    How to load username and password for external application?
    For each user, we should take its Portal username and password for one specific external application. How to do that ?
    Regards.

    ABSOLUTLY YES !!!!
    We already know the external application login information for each user and we want to by pass this user task. (Specially because the user itself doesn't know its username/password for the external appli). In fact we are trying to integrate IStore product to Portal by using this mechanism.
    <BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by Kamalendu Biswas ([email protected]):
    If you define an external application then SSO users can populate user information by themselves.
    Are you syaing that you want to populate user information automatically (bulk lodad)?<HR></BLOCKQUOTE>
    null

  • WD ABAP - Reading the URL Parameters for FPM application

    Hi,
    As per the Custom requirment,
    I want to pass URL parameters for WD ABAP application (sap/bc/webdynpro/dbm/app_veh_cus_search) which uses FPM.
    example: sap/bc/webdynpro/dbm/app_veh_cus_search?Customer=12345&fromExternal=true
    I am facing difficulty in reading the URL parameters.
    How to read/get the URL Parameters for an FPM WD ABAP application????
    Observation:
    I tried reading the parameter in Window --> HANDLEDEFAULT method. But could NOT read the Parameters from here for FPM application whereas if I create a Z Custom application then I could read the URL Parameters. so the issue is in reading the URL Parameters for FPM application.
    Kindly support
    Regards,
    Hussain

    Hi Hussain,
    You can do this either with the methods of interface if_fpm_parameter...
    DATA lo_param TYPE REF TO if_fpm_parameter.
    lo_param = cl_fpm_factory=>get_instance( )->mo_app_parameter.
    CALL METHOD lo_param->get_value
        EXPORTING
            iv_key   = parameter_name
        IMPORTING
            ev_value = parameter_value.
    or a more generic approach using class cl_wd_runtime_services...
    cl_wd_runtime_services=>get_url_parameter
    Cheers,
    Amy

  • Unicode mode for Planning applications

    Is Unicode mode for Planning applications allowed in 11.1.2.1? If so how do you allow it?
    Seems that it is not allowed but the documentation is ambigious, and a search on the forum does not give clear answer.

    Thanks!
    But then why does the 8-character limit apply to unicode planning application names?
    Shouldn't ticking that checkbox enable longer application names?
    What's the limit for unicode Essbase applications, 32 characters? Then one should also be able to give a new unicode planning application a 32 character long name when in the create new planning application dialogue box, given that the data source is 'unicode'.
    Edited by: Markus on Aug 4, 2011 5:06 AM

  • Commands for Planning Applications in WAD?

    Hi all,
    Following the developers' guide on 'Business Planning and Analytical Services'  for 2004S we got stuck on assigning custom Commands for Planning Applications in WAD, which were created in the planning wizard.
    The option for 'Commands for Planning Applications' does NOT show up in the command wizard!
    is there a ABAP/Java stack pre-requisite for this or is there a new(?) authorisation object missing?
    Does it helps for others? On which Java Stack?
    Thx,
    Markus

    Check OSS note 948336.

  • How to design Flat file for loading attribute dimension in a planning application

    Dear Gurus,
    I have a requirement to extract attribute dimensions from an essbase application and load it to another planning application. I have a dimension called Program and two attribute dimensions Sales Manager, Accounts manager associated with Program dimension in Essbase application. I will Extract these dimensions using Essbase outline extractor. After Extracting the attribute dimensions I have to load these dimensions to planning applications using outline load utility. Kindly guide me how to design the flat file for loading attribute dimensions in planning application.
    Thanks and Regards
    SC

    You could dig through the docs and try to figure out the file format manually, or you could do this the easy way.  Simply use the Outline Load Utility to export your attribute dimension from Planning.  The export file format is the same as the import file format.  You might have to manually add a couple of test members to your attribute dimension so that your export file has some content.  Then simply update the file you exported, and import it.
    (I am assuming you have already manually created the Attribute dimension in Planning, and that you simply need to add members to it.)
    Hope this helps,
    - Jake

  • Low Cost Load Balancer / Reverse Proxy for 2 Oracle Application Servers

    If you have 2 OAS and you need to setup a load balancer / reverse proxy infront of it and you can't use webcache or a hardware load balancer what's the best way to setup a low cost solution that would preserve your session state if you have a OC4J clustered application running on the MT?

    Just a quick answer, please:
    If you think about Oracle WebCache as a general application, you will find some useful Technical White Papers on http://otn.oracle.com/clusterware They will explain, how Oracle Clusterware can be used to protect any kind of application.
    In general, Oracle Clusterware and Oracle WebCache must be installed on the same set of servers (cluster nodes) in this case. Regarding the question of whether or not you can re-use your 2 SUN servers: It depends.
    Oracle Clusterware requires shared storage and a private interconnect. Your current infrastructure might need to be reviewed and enhanced in those regards, especially, since your servers are geographically separated as you said.
    Just some ideas. Thanks.

  • ConnCacheBean Setting for a Load Balance  URL

    Hi,
    We are using the ConnCacheBean to set the URL property. We have a new load-balance database, how can I pass that on as a paramter? Thanks.
    <jsp:setProperty name="tdbean" property="URL" value= "jdbc:oracle:thin:@----" />
    Thanks.

    Hi,
    I would pass this to the database forum as this class belongs to the Oracle JDBC package
    Frank

  • Load balancing and HA for office web apps server Lync 2013

    Hi,
        I have 12000 users, 3 FE servers in a pool, 2 edge server in a pool, HA required, IM/presence, A/V, WEb conferencing required. plan to have 2 office web apps server a farm with HA, below are my queries
    1.  which type of load balancing i need....DNS or HLB for office web app servers? if its HLB then is it mandatory?
    2. i have already 2 HLB for FE pool .. one for externa url , one for internal URL...can i use the same HLB for office web app servers ?
    3. one more question regarding EDGE pool load balancing, can i use the same HLB  in EDge pool also that i am using for FE pool?

    Hi,
    1.  which type of load balancing i need....DNS or HLB for office web app servers? if its HLB then is it mandatory?
    WebApps runs on https and you cannot load balance http traffic using DNS load balancing. you need to have a HLB.
    2. i have already 2 HLB for FE pool .. one for externa url , one for internal URL...can i use the same HLB for office web app servers ?
    you can use the same HLB for that
    3. one more question regarding EDGE pool load balancing, can i use the same HLB  in EDge pool also that i am using for FE pool?
    for that one, you probably need a separate HLB.  
    Z-Hire -- Automate Lync User Account creation process ( AD / Exchange / Lync )

  • Oracle 10g webcache as load balancer with Clusterware for HA

    Hi All
    I'm trying to put together a solution for my organisation to include a resilient load balanced setup without buying hardware load balancing kit. We are implementing an Oracle Forms based product from a software supplier on the Oracle 10g Forms & Reports Services platform v10.1.2.2.0. The intention is to balance the production load of the application across 2 identical Sun T2000 servers - each could support the full load independently if necessary. The servers are geographically separated for resilience. The supplier has recommended implementing Webcache on one of these T2000 servers as a load balancer - this works fine, but presents a single point of failure and no automatic failover.
    I have read an Oracle white paper explaining that Oracle Webcache as a load balancer can be made into a HA solution by using Oracle Clusterware. What isn't clear from the paper is this;
    1. Whether I need to have Webcache as a load balancer & Clusterware installed separately on a different pair of servers ?
    2. Can I simply configure Webcache for load balancing on both of my Sun servers and use Clusterware to failover the load balancing function from one server to the other if one fails ?
    Can anyone point me in the right direction with this please ?
    Many thanks
    Dean

    Just a quick answer, please:
    If you think about Oracle WebCache as a general application, you will find some useful Technical White Papers on http://otn.oracle.com/clusterware They will explain, how Oracle Clusterware can be used to protect any kind of application.
    In general, Oracle Clusterware and Oracle WebCache must be installed on the same set of servers (cluster nodes) in this case. Regarding the question of whether or not you can re-use your 2 SUN servers: It depends.
    Oracle Clusterware requires shared storage and a private interconnect. Your current infrastructure might need to be reviewed and enhanced in those regards, especially, since your servers are geographically separated as you said.
    Just some ideas. Thanks.

  • Load dimensions and members in Planning application via outline load

    it is a classic planning application, after I load dimensions and members into classic Planning application, I can't see new members I added in csv file.
    How could I confirm whether it was successfully loaded.
    This is the log. Please refer to it.
    Successfully logged into "予算応用" application, Release 11.121, Adapter Interface Version 5, Workforce supported and enabled, CapEx supported and enabled, CSS Version 3
    "Account" dimension properties and information:
    Account, Parent, Alias: Default, Alias: FromDepartment, Alias: ToDepartment, Valid For Consolidations, Data Storage, Two Pass Calculation, Description, Formula, UDA, Smart List, Data Type, Operation, Account Type, Time Balance, Skip Value, Exchange Rate Type, Variance Reporting, Source Plan Type, Plan Type (PL), Aggregation (PL), Plan Type (BS), Aggregation (BS), Plan Type (Plan3), Aggregation (Plan3), Plan Type (Wrkforce), Aggregation (Wrkforce), Plan Type (Capex), Aggregation (Capex)
    UDA's bound to "Account" dimension: HSP_NOLINK
    "Period" dimension properties and information:
    Period, Parent, Alias: Default, Alias: FromDepartment, Alias: ToDepartment, Data Storage, Two Pass Calculation, Description, Formula, UDA, Smart List, Data Type, Operation, Type, Start Period, End Period, Aggregation (PL), Aggregation (BS), Aggregation (Plan3), Aggregation (Wrkforce), Aggregation (Capex)
    No UDA's defined on "Period"
    "Year" dimension properties and information:
    Year, Parent, Alias: Default, Alias: FromDepartment, Alias: ToDepartment, Data Storage, Two Pass Calculation, Description, Formula, UDA, Smart List, Data Type, Operation
    No UDA's defined on "Year"
    "Scenario" dimension properties and information:
    Scenario, Parent, Alias: Default, Alias: FromDepartment, Alias: ToDepartment, Valid For Consolidations, Data Storage, Two Pass Calculation, Description, Formula, UDA, Smart List, Data Type, Operation, Start Year, Start Period, End Year, End Period, Exchange Table, Include BegBal, Process Management Enabled, Aggregation (PL), Aggregation (BS), Aggregation (Plan3), Aggregation (Wrkforce), Aggregation (Capex)
    UDA's bound to "Scenario" dimension: ACTUAL
    "Version" dimension properties and information:
    Version, Parent, Alias: Default, Alias: FromDepartment, Alias: ToDepartment, Data Storage, Two Pass Calculation, Description, Formula, UDA, Smart List, Data Type, Operation, Version Type, Process Management Enabled, Aggregation (PL), Aggregation (BS), Aggregation (Plan3), Aggregation (Wrkforce), Aggregation (Capex)
    No UDA's defined on "Version"
    "Currency" dimension properties and information:
    Currency, Parent, Alias: Default, Alias: FromDepartment, Alias: ToDepartment, Data Storage, Two Pass Calculation, Description, Formula, UDA, Smart List, Data Type, Operation, Symbol, Scale, Triangulation Currency, Reporting Currency, Thousands Separator, Decimal Separator, Negative Style, Negative Color
    No UDA's defined on "Currency"
    "Entity" dimension properties and information:
    Entity, Parent, Alias: Default, Alias: FromDepartment, Alias: ToDepartment, Valid For Consolidations, Data Storage, Two Pass Calculation, Description, Formula, UDA, Smart List, Data Type, Operation, Base Currency, Plan Type (PL), Aggregation (PL), Plan Type (BS), Aggregation (BS), Plan Type (Plan3), Aggregation (Plan3), Plan Type (Wrkforce), Aggregation (Wrkforce), Plan Type (Capex), Aggregation (Capex), NumericAttrib
    No UDA's defined on "Entity"
    "NumericAttrib" attribute dimension (on base dimension "Entity"). NO attributes defined on the "NumericAttrib" dimension.
    NumericAttrib, Parent, Alias: Default, Alias: FromDepartment, Alias: ToDepartment, Operation
    "Employee" dimension properties and information:
    Employee, Parent, Alias: Default, Alias: FromDepartment, Alias: ToDepartment, Valid For Consolidations, Data Storage, Two Pass Calculation, Description, Formula, UDA, Smart List, Data Type, Operation, Aggregation (Wrkforce)
    No UDA's defined on "Employee"
    "Line Item" dimension properties and information:
    Line Item, Parent, Alias: Default, Alias: FromDepartment, Alias: ToDepartment, Valid For Consolidations, Data Storage, Two Pass Calculation, Description, Formula, UDA, Smart List, Data Type, Operation, Aggregation (Capex)
    No UDA's defined on "Line Item"
    "Asset Class" dimension properties and information:
    Asset Class, Parent, Alias: Default, Alias: FromDepartment, Alias: ToDepartment, Valid For Consolidations, Data Storage, Two Pass Calculation, Description, Formula, UDA, Smart List, Data Type, Operation, Aggregation (Capex)
    No UDA's defined on "Asset Class"
    Exchange Rates properties:
    Table, Description, To Currency, From Currency, Operation, Method, Historical, Beg Balance, Year, Period, Average, Ending
    UDA properties:
    Dimension, UDA, Operation
    Smartlist properties:
    SmartList Name, Operation, Label, Display Order, Missing Label, Use Form Missing Label, Entry ID, Entry Name, Entry Label
    No Planning Unit Hierarchies are defined in this application.
    Translation input file fields:
    Value, Driver Member, Point-of-View, Data Load Cube Name
    [Thu Oct 27 18:16:18 JST 2011]Successfully located and opened input file "C:\TEMP\PLNentityバージョンのエクスポート.csv".
    [Thu Oct 27 18:16:18 JST 2011]Input file being read with UTF-8 encoding.
    [Thu Oct 27 18:16:18 JST 2011]Detected a UTF-8 BOM marker in input file "C:\TEMP\PLNentityバージョンのエクスポート.csv".
    [Thu Oct 27 18:16:18 JST 2011]Header record fields: Entity, Parent, Alias: Default, Alias: FromDepartment, Alias: ToDepartment, Valid For Consolidations, Data Storage, Two Pass Calculation, Description, Formula, UDA, Smart List, Data Type, Base Currency, Plan Type (PL), Aggregation (PL), Plan Type (BS), Aggregation (BS), Plan Type (Plan3), Aggregation (Plan3), Plan Type (Wrkforce), Aggregation (Wrkforce), Plan Type (Capex), Aggregation (Capex)
    [Thu Oct 27 18:16:18 JST 2011]Located and using "Entity" dimension for loading data in "予算応用" application.
    [Thu Oct 27 18:16:18 JST 2011]Load dimension "Entity" has been unlocked successfully.
    [Thu Oct 27 18:16:18 JST 2011]A cube refresh operation will not be performed.
    [Thu Oct 27 18:16:18 JST 2011]Create security filters operation will not be performed.
    [Thu Oct 27 18:16:18 JST 2011]Examine the Essbase log files for status if Essbase data was loaded.
    [Thu Oct 27 18:16:18 JST 2011]Planning Outline load process finished (with no data load as specified (/N)). 9 data records were read, 9 data records were processed, 9 were accepted, 0 were rejected.

    Thank you for your reply.
    With your help, I can verify it easier rather than creating dataform to verify it.
    I have resolved the question now, the root cause is I had used the wrong parameter, shouldn't add '/N' in the command. for /N is a dry run to check whether there are error in CSV file, it won't perform metadata load.
    If no error occured, run the command without /N, then the metadata load will be performed.
    I refer to this artical,
    http://john-goodwin.blogspot.com/2008/08/time-to-look-in-bin.html
    Best regards,
    Samantha
    Edited by: Samantha on 2011-10-31 下午4:39

Maybe you are looking for