Load is high during VM creation

Hi ,
My OracleVM server Load is goes very high while creating a 250GB VM.
Environment :
Physical RAM : 16 GB
CPU's : 8
Disk : 135 GB+512 GB(SAN)
VMserver : RAM :830MB
VM : DISK Space :250GB RAM:6GB CPU:3
Top Output from VMSERVER :
top - 21:04:07 up 2:19, 2 users, load average: 36.88, 36.13, 33.93
Tasks: 198 total, 2 running, 196 sleeping, 0 stopped, 0 zombie
Cpu0 : 0.0%us, 0.0%sy, 0.0%ni, 0.0%id,100.0%wa, 0.0%hi, 0.0%si, 0.0%st
Cpu1 : 0.0%us, 0.0%sy, 0.0%ni, 0.0%id,100.0%wa, 0.0%hi, 0.0%si, 0.0%st
Cpu2 : 0.0%us, 0.0%sy, 0.0%ni, 0.0%id,100.0%wa, 0.0%hi, 0.0%si, 0.0%st
Cpu3 : 0.0%us, 0.0%sy, 0.0%ni, 0.0%id,100.0%wa, 0.0%hi, 0.0%si, 0.0%st
Cpu4 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
Cpu5 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
Cpu6 : 0.0%us, 0.3%sy, 0.0%ni, 0.0%id, 99.7%wa, 0.0%hi, 0.0%si, 0.0%st
Cpu7 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
Mem: 854192k total, 850404k used, 3788k free, 9752k buffers
Swap: 1052216k total, 148k used, 1052068k free, 653580k cached
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
1 root 15 0 2044 636 540 S 0 0.1 0:00.50 init
2 root RT 0 0 0 0 S 0 0.0 0:00.01 migration/0
3 root 34 19 0 0 0 S 0 0.0 0:00.01 ksoftirqd/0
4 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0
5 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/1
6 root 34 19 0 0 0 S 0 0.0 0:00.00 ksoftirqd/1
7 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/1
8 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/2
9 root 39 19 0 0 0 S 0 0.0 0:00.00 ksoftirqd/2
10 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/2
11 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/3
12 root 34 19 0 0 0 S 0 0.0 0:00.00 ksoftirqd/3
13 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/3
14 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/4
15 root 34 19 0 0 0 S 0 0.0 0:00.00 ksoftirqd/4
Kindly help me out in reducing the Load,
Also let me know ideally how much time will take to create a 250GB Virtual Machine ?
Thanks in advance,
--Sri

hi all,
I checked the environment again,
then came to know that my SAN is not connected through FIbre Channel or any other faster channel to the Server and its connected through 100MBPs line... this was causing the slow and also there was a lot IO wait in my Oracle VM server.
Thanks,
Sri.

Similar Messages

User Exit/ Badi for Changing Quant parameters during TO Creation

Hi Gurus,
Could you please guide me to advice the User Exit/Badi which can be used for changing Quant Data during TO Creation.
User Requirement: Using "Recepient Field" in MIGO as a Key Value for FIFO in WM during goods issue. Receipient is copied into TR and TO (Standard SAP Functionality). For the purpose of Stock Removal based on Receipient Value, we need to copy this value into Quant Data field named Certificate Number ("LQUA-ZEUGN").
I will highly appreciate reply from Gurus.
Regards,
Gupta M

Hi manish,
Use the Exit MWMTO001 for this purpose and modify the table accordingly. This will solve your problem.
Thanks,
Shibashis

Site does not load after some minutes of creation or after restart the server

Hello,
I have been asked to create a test enviroment identical to the production enviroment. So, what I did was:
Backed up the production web application's content database: Prod_WSS_ContentDB
Created new test servers (domain controller, sql server and sharepoint 2013 server) in a new, completely isolated, network environment, without any connection with the production environment (specifically Azure)
Created a new web application in test environment with a new content database.
Dismounted the new content database with powershell: Dismount-spcontentdatabase Test_WSS_Content
Copy the Prod_WSS_ContentDB database to the test sql server and restored it with Management Studio.
Mount the Prod_WSS_ContentDB databe to the web application with powershell:
Mount-spcontentdatabse Prod_WSS_ContentDB -WebApplication http://testsp/
Then, when I type http://testsp in the browser it redirects me to http://testsp/SitePages/Home.aspx
and the site loads exactly as the production environment.
But, after some minutes, or if I restart the Sharepoint Server, when I navigate to
http://sitesp I am redirected to http://testsp/SitePages/Home.aspx
as expected, but the site does not load, the browser just show a complety blank page.
The Central Administration site loads normally.
Trying to fix it I found that if I dismount the content database Prod_WSS_ContentDB, then mount the test database Test_WSS_Content,
then navigate to the site, dismount Test_WSS_Content and finally mount again Prod_WSS_ContentDB, the site loads normally, no blank page, but after some minutes or if I restart the same happens again.
For the error event I receice in event viewer it seems that the problem is related to database. I have not found a solution for this error... How can I solve this?
The error is:
Log Name: Application
Source: Microsoft-SharePoint Products-SharePoint Foundation
Date: 6/27/2014 2:44:22 PM
Event ID: 5586
Task Category: Database
Level: Error
Keywords:
User: UCETEST\spaccount
Computer: TESTSP01.ucetest.edu.do
Description:
Unknown SQL Exception -2146893055 occurred. Additional error information from SQL Server is included below.
A connection was successfully established with the server, but then an error occurred during the pre-login handshake. (provider: SSL Provider, error: 0 - The handle specified is invalid)
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-SharePoint Products-SharePoint Foundation" Guid="{6FB7E0CD-52E7-47DD-997A-241563931FC2}" />
<EventID>5586</EventID>
<Version>15</Version>
<Level>2</Level>
<Task>3</Task>
<Opcode>0</Opcode>
<Keywords>0x4000000000000000</Keywords>
<TimeCreated SystemTime="2014-06-27T14:44:22.743159500Z" />
<EventRecordID>4742</EventRecordID>
<Correlation />
<Execution ProcessID="1688" ThreadID="1692" />
<Channel>Application</Channel>
<Computer>TESTSP01.ucetest.edu.do</Computer>
<Security UserID="S-1-5-21-2552298216-324766354-3392103171-1108" />
</System>
<EventData>
<Data Name="int0">-2146893055</Data>
<Data Name="string1">A connection was successfully established with the server, but then an error occurred during the pre-login handshake. (provider: SSL Provider, error: 0 - The handle specified is invalid)</Data>
</EventData>
</Event>
Melvintt
MCTS, Windows Server 2008 R2: Network Infrastructure
MCTS, Windows Server 2008 R2: Active Directory, Configuring

Hi,
According to your post, my understanding is that Site does not load after some minutes of creation or after restart the server.
Please make sure you create a test environment for existing production site correctly.
Here are some great articles for your reference:
Moving content between SharePoint environments
Copy SharePoint production data to a test environment
Build a SharePoint 2010 Test/Development Farm
Best Regards,
Linda Li
Linda Li
TechNet Community Support
Hello Linda Li,
I follwed that steps to create my test enviroment... and I have recreated it some times using that same steps, but the problem persits. After some minutes or after I restart the SharePoint server the site does not load.
Melvintt
MCTS, Windows Server 2008 R2: Network Infrastructure
MCTS, Windows Server 2008 R2: Active Directory, Configuring

Error message during cube creation

Hi expert,
System show the following error message during cube creation, please info how to solve this problem. Thanks.
Define the characteristics of the validity table for non-cumulatives
Message no. R7846
Diagnosis
The InfoCube contains non-cumulative values. A validity table is created for these non-cumulative values, in which the time interval is stored, for which the non-cumulative values are valid.
The validity table automatically contains the "most detailed" of the selected time characteristics (if such a one does not exist, it must be defined by the user, meaning transfered into the InfoCube).
Besides the most detailed time characteristic, additional characteristics for the InfoCube can be included in the validity table:
Examples of such characteristics are:
A "plan/actual" indicator, if differing time references exist for plan and actual values (actual values for the current fiscal year, plan values already for the next fiscal year),
the characteristic "plant", if the non-cumulative values are reported per plant, and it can occur that a plant already exists for plant A for a particular time period, but not yet for plant B.
Procedure
Define all additional characteristics that should be contained in the validity table by selecting the characteristics.
In the example above, the characteristics "plan/actual" and "plant" must be selected.
The system automatically generates the validity table according to the definition made. This table is automatically updated when data is loaded.

Hi,
Go to the Extras Tab in the definition of the Cube and there select " Maintain Non-Cumulatives" and there select the Plant check box. You can also check Material but it is not recommended. Now try to activate the cube. I think it will work for you.

No Authorization to OLAP Cubes during the creation of universe connection

Hello friends we are not able to see the OLAP Cubes during the creation of universe connection using the Quality system and Application server "sapbmw01" client 100, system # 00. But we are able to set up the connection in our development system.
I will highly appreciate if you can let me know if we need some special role to access the OLAP Cubes during the creation of universe connection using the Q system.
Surprisingly we are using SAP_BW_ALL in Quality system still we are not able to access the infocubes. is there some thing missing in CMS IN BO to make that work.
Thanks
Soniya

Hi Jyothy,
Refer the below link on how to create universe on Analytic View/Calculation View using relation connection in IDT
http://www.sapanalyticsguru.com/index.php/sap-bobi/31-universe-creation-on-hana-view-using-information-design-tool

Regarding Performance concerns during the creation of Infocube

hai
im going to create the infocube on top of ODS.
Pls tell me some design tips for performance things during the creation of Infocube like partitioning , Indexes...
Basically im loading from Oracle Databasetables by using DB-COnnect .
pls tell me
i ll assing the points
bye
rizwan

hi Rizwan,
check these:
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/1955ba90-0201-0010-d3aa-8b2a4ef6bbb2
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/ce7fb368-0601-0010-64ba-fadc985a1f94
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/4c0ab590-0201-0010-bd9a-8332d8b4f09c
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/3a699d90-0201-0010-bc99-d5c0e3a2c87b
assign points if useful ***
Thanks,
Raj

How to Load a Panel during run time from a CVI dll

Hi,
I want to execute/load a panel during runtime, from a CVI dll function.
my CVI dll "test.dll" has "READ_PAN" function. while executing this function from a Test Stand Action step i want Configure Panel (from FR_GUI.uir) to pop up.
can you please suggest me how can i do this from my "test" project of CVI.
int __stdcall __export RunFRConfig (CAObjHandle step,CAObjHandle thisContext)
   ERRORINFO errorInfo;
   char errMsg[1024];
    int pan;
    pan = LoadPanelEx (0, "FR_GUI.uir", READ_PAN, __CVIUserHInst);
    DisplayPanel (pan);
    RunUserInterface();
    DiscardPanel (pan);
    return 0;
        Error:
   // sprintf(FinalErrMsg,"Configure Error: %s",errMsg);
return -1;

Thanks for ur reply.
Hello Asad,
It is possible to maximize the run time previewer when calling reports from forms. U need to set a parameter named 'MAXIMIZE' to do that.
I m attaching a code sample for u. This is working in my production environment.
DECLARE
pl_id ParamList;
BEGIN
     pl_id := Get_Parameter_List('setProposal');
     IF NOT Id_Null(pl_id) THEN
          Destroy_Parameter_List( pl_id );
     END IF;
     pl_id := Create_Parameter_List('setProposal');
// This parameter is set to hide parameter form at run time
     Add_Parameter(pl_id, 'PARAMFORM', TEXT_PARAMETER, 'NO');
// This parameter is used to maximize previewer window at run // time
     Add_Parameter(pl_id, 'MAXIMIZE', TEXT_PARAMETER, 'YES');
Run_Product(REPORTS, 'sample.rep', SYNCHRONOUS, RUNTIME,
FILESYSTEM, pl_id, NULL);
END;
Feel free to contact me if u need anymore assistance.
Take care and bye

Error during PO creation "Total BED % rate exceeds 100 % "

Hi.
Its concerned to Indian Excice.
Error during the creation of PO is " Total BED % rate exceeds 100 % " ,
( Message no. 8I453).
And you pls note in J1ID its 16% maintained for that perticular chapter id and its 100% for BED in tax code.
Can you pls tell me the reason for this error.
Regds

Hi Santosh,
362 is not maintained for BASB,but its maintained for condition type JMO1(IN:A/P BED Deductable) & JMO2(IN: A/P BED non deduct )in <b>AltCTy</b> field.
And For BASB 605 is maintained in the field AltCBV.
Can you Pls explain the significance of this alternative calculation type.
Regds

Checks on vendors during the creation of PO with ME21N

Hi all,
i have this problem:
during the creation of a Purchase Order, for some types of them i have to bypass some checks that are made by standard on the Vendor.
Is it possibile to do? if it is, how can i do it?
Thanks
Lello

Hi
If they are standard controls, probably it'll mean to change the standard program: if your SAP release is ECC 6.00 u can try to use the Implicit Enhancement in order to change the standard else u need to register the standard to OSS in order to get the access key for modification.
Max

Automatic Partner Determination Std Contact Person during Activity Creation

Hi ,
There is a requirement in my project where the Standard Contact Person of the Sold to Party should be automatically determined during Activity Creation .I have completed the Partner Function configurations and now the Standard Contact Person is being successfully determined as the Partner.
However, there is a problem in a scenario where in another Contact Person other than the Standard Contact Person is to be determined during Activity Creation . In that case, the option to select the other Person is not being offered through a pop up window, but the System automatically populates the next Contact Person based on the BP Id ( Next on the Number Range )
Is there any way , so that the normal procedure of selecting one Contact Person from a list in the Pop Window can be incorporated , once the standard Contact Person is being removed from the Contact Person field in the Business Transaction .
<< Moderator message - Please do not promise points >>
Regards,
Maroof
Edited by: Rob Burbank on Jan 5, 2011 5:06 PM

Hello Maroof,
you should check first the standard relationship flag of the account. Means check the account and go to the
relationship contact person.
There you will find the standard Relationship Flag, which is relevant for the system to determine the main CP.
Furthermore please check the partner procedure:
For each partner function you can enter a value in field Maximum and Selection Limit. Please consider the F1 help
for the field Selection Limit where you can find the explanation when and how the selection popup is triggered:
Example 1
You enter 3 in this field.
When the system finds three or more partners who could fulfill this partner function, it displays a selection list.
You choose from the list which partners to enter in the transaction.
Example 2
You do not mark this field, but enter 5 as the Maximum for this partner function.
When the system finds six or more appropriate partners it displays a selection list.
Hopefully this information helps you.
Regards
Rene

Serial Number validation during Delivery Creation itself(PGI-system checks)

Process:
Sales Order PR(Purchase Order) GR( New Serial Numbers are created automatically or manually keyed in)
Once the Goods Receipt is received, we do the (SO) DELIVERYu2014SERIAL NUMBER ASSIGNMENT Post Goods Issue
Issue:
Current Serial Number Profile Management does not do a valid serial number check during DELIVERY CREATION where we do a SERIAL NUMBER ASSIGNMENT.
Only during POST GOODS ISSUE, the check happens for valid serial numbers; this is too late in the game for business as there is a time lag of 3 days from the DELIVERY CREATION and PGI.
Reason being--- We donu2019t check the following u201C Existing Stock Checku201D( which does a serial number validation during delivery creation as well)
SPRO>Plant Maintenance and Customer Service>Master Data in Plant Maintenance and Customer Service>Technical Objects>Serial Number Management>Define Serial Number Profiles
If we check this option, the business requirement to do a valid serial number check does happen during delivery creation, however we cannot create new serial numbers during Purchase Order- GOODS RECEIPT.
QUESTION:
Can we have the system check the valid serial numbers from stock during delivery creation and serial number assignment.
And Also create new serial numbers during Purchase Order- Goods Receipt.

Hi
1.In std SAP its not possible to check the serail number during Delivery creation, through enhancement it can be done.
2.During GR for PO serial numbers can be created.
Rgds
Ramesh

Issue during automatic Creation of Work Order from Notification

Hi,
I have a issue during automatic Creation of Work Order from Notification.
BADI implemented: NOTIF_EVENT_POST
BAPI called in BADI: BAPI_ALM_ORDER_MAINTAIN
I am able to create Work Order successfully but after that i need to update notification header with created work order number.
But i am unable to update the same (VIQMEL-AUFNR).
Can anybody provide solution for the same!
Thanks,
Kumar.

Hi,
Any inputs on above posted issue!
Thanks in advance.
Thanks,
Kumar.

Automating Goods issue during Delivery creation

Hi all,
We have a requirement to automate the Goods issue creation for certain type of orders when the Delivery is getting created. The orders that need to be automatically Goods issued during delivery creation are identified based on certain plants. These plants are linked to certain output type and in the output type routine is the standard program RVADEK01 with one additonal code for automating the Goods Issue creation.
We have a custom table that holds the status of orders and there is a code in user exit userexit_save_document_prepare which changes the status of the order as closed when the goods issue is done.
But when the delivery is saved, in this case when an automatic goods issue needs to happen, when the flow reaches this user exit, the output type code dosenot get executed and the Goods issue is not done and so the custom table will not be updated with the closed status. So we are in need to findout a place where we can update the status of the order in that table.
The output type code is not executed even before the other user exit userexit_save_document. The output type code gets executed and goods issue is done after the this userexit_save_document when the COMMIT statement is executed in the subroutine BELEG_SICHEN_POST in the include FV50XF0B_BELEG_SICHERN.
I need help in finding out if any user exit or badi is called after this commit statement, so that I can add my code to close the status of the order in my custom table. Just after this commit the Goods issue happens and the VBFA table gets updated with the 'R' records for goods issue.
Please let me know if anyone has any idea on this. The ultimate goal is to find some place after the goods issue is done to update the status of the order as closed in the custom table we have.
Thanks,
Packia

Dear Siva,
As informed yesterday I changed the language from DE to EN, to match the other shipping points settings in table V_TVST, this did not bring the solution.
Please let me summarize, I am really desparate here:
This is only IM related, Not WM.
Picking lists are not printed for any Shipping Point from this warehouse, this is just a small subsidiary of my customer in Finland.
Issue is not Aut. PGI.
VP01SHP has not been configured for any shipping points, still there we do get the PR except for the new shipping point.
In the deliveries of correct processed shipping points I do not find any picking output type.
Item category in new shipping is equal to Item category in already existing shipping points, so no need to config here.
There is no picking block active.
PR creation happens once I enter the pick qty in the delivery in VL02N. This is the part that we need to have automated.
Can you please try to help me out?
Tnx & regards,
Chris

Hard Check During Delivery Creation

Hello Experts,
Need your advice. I am stuck up in a enhancement issue during delivery creation. i am working for passenger vehicle company.
Back ground Info.
the company procures chassis from vendor & builds bus body over it. there are various types of chassis & each is uniquely identified in SAP by Material No. & also mentioned in BOM created for bus. when chassis is received , equipment is created using T-code IE01. After this one more equipment is created for bus which is called BBD Serial No. The equipment for BBD serial no holds chassis serial no. My issue is at the time of creation of delivery using T-code VL01N the user puts the BBD Serial No manually in a dialog box provided, This BBD Serial No is not capturing in the importing structure IT_XLIPS of BADI "LE_SHP_DELIVERY_PROC" Method "Delivery_Final_Check".
I have to put a check during delivery creation for consumption of Chassis , if the Chassis is consumed during production phase a Mat Doc will be generated with movement Type 261. As such we don't knew the Mat Doc for Chassis Serial no Consumed during prod phase. so to derive chassis no in the BADI against which we have to check for it's consumption. The user provide BBD Serial no in a standard dialog box in VL01N.
Can we use Field Exit for this or any other BADI Should work.
Best Regards
Priyesh Shah

Hi Priyesh,
Below steps may help you to get the value of the standard dialog box provided in the screen.
1. Find the field name of the standard dialog box provided in the the screen for BBD Serial no.
2. Implement below code in the BAdI "LE_SHP_DELIVERY_PROC" method.
FIELD-SYMBOLS: <fs> TYPE BBDFIELDTYPE.
ASSIGN ('(SAPMV50A)BBDFIELDNAME') TO <fs>.
Now the field symbol <fs> will hold the value passed in the dialog box.
Please try and let me know if it is working or not.
Thanks
Gangadhar

Analysis Services failing to Start . File system error: Error occurred during the creation of directory

Hello All,
Posting this problem here and hoping for a solution from the experts in this forum.
When i have restarted the Analysis Services , i see that it has been stopped but never started back. It fails with an error
"The SQL Server Analysis Services (MSSQLSERVER) service on Local Computer started and then stopped. Some services stop automatically if they are not in use by other services or programs."
When Checked the Event Viewer i see the following error -
The service cannot be started: The following system error occurred: The filename, directory name, or volume label syntax is incorrect. File system error: Error occurred during the creation of directory: '\\?\E:\OLAP\MSSOLAPFactory\OlapData;M:\Test
Backup'.
I remember changing the BackupDir value of Analysis Services few days back, and i think it could have impacted. Can you please help me how can i change back the BackupDir value and have the server back?
Let me know if you need any more details
SG

Is this still an issue? If so, I would find msmdsrv.ini and make sure you don't have two folders listed in the BackupDir (or DataDir or TempDir). You'll have to runas Administrator to edit the msmdsrv.ini file and save changes. Once you fix that, it should
succeed.
http://artisconsulting.com/Blogs/GregGalloway

Load is high during VM creation

Similar Messages

Maybe you are looking for