Loading Windows 7 x64 on H520s

Hi all,
I have an H520s, brand new. I am trying to load Windows 7 x64 on it. Upon booting from the DVD, I got an error; something about "Secure Boot" in Setup. So I went in there and disabled Secure Boot. Now, at least, the PC will boot from the DVD.
However, after the Windows boot DVD "loads files", it goes to the "Starting Windows" screen with the 4-colored flag and just sits there forever. No progress, and I can't do anything.
Help! Thanks!
Chris
Solved!
Go to Solution.

Hi,
Is "the exact same problem" the " cannot load windows on this disk" message?
IIRC you can select advanced options when you get to the disk selection screen. Delete all existing partitions and exit. The installer should continue with an MBR install from there.
If that doesn't work, use F10 to launch a command prompt and run DISKPART (see online diskpart documentation) and do a list disk, select, clean, and convert mbr. Exit and continue the install.
It's possible that you'll have to restart the installation.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Similar Messages

Office 2007 add-ins will not load on Windows 7 x64

Hi there,
I have a brand new built Windows 7 x64 desktop with Office 2007 32 bit installed. When I install Oracle BI Publisher Desktop 11.1.1.7.0 it loads without errors. Except none of the add-ins will load. I have done the usual Add-ins / Com Add-in / Tick box but nothing.
After further investigation it appears there is a VSTO 4.0 error on the machine when I run the C:\Program Files (x86)\Oracle\BI Publisher\BI Publisher Desktop\DotNet2007\TBAddin.vsto. The error itself is only failed when it tries to download savexmldata.png from C:/Program Files (x86)/Oracle/BI Publisher/BI Publisher Desktop/DotNet2007/Resources. The fact is there isn't a folder called Resources nor a file called savexmldata.png.
I thought it may be an assemblies error and tried installing the newest versions of Microsoft Office 2007 Primary Interop Assemblies and Microsoft Visual Studio 2010 Tools Office Runtime (x64) but all are up to date.
See below for the error:-
Customization URI: file:///C:/Program Files (x86)/Oracle/BI Publisher/BI Publisher Desktop/DotNet2007_2/ETBAddIn.vsto
Exception: Downloading file:///C:/Program Files (x86)/Oracle/BI Publisher/BI Publisher Desktop/DotNet2007_2/Resources/field.png did not succeed.
************** Exception Text **************
System.Deployment.Application.DeploymentDownloadException: Downloading file:///C:/Program Files (x86)/Oracle/BI Publisher/BI Publisher Desktop/DotNet2007_2/Resources/field.png did not succeed. ---> System.Net.WebException: Could not find a part of the path 'C:\Program Files (x86)\Oracle\BI Publisher\BI Publisher Desktop\DotNet2007_2\Resources\field.png'. ---> System.Net.WebException: Could not find a part of the path 'C:\Program Files (x86)\Oracle\BI Publisher\BI Publisher Desktop\DotNet2007_2\Resources\field.png'. ---> System.IO.DirectoryNotFoundException: Could not find a part of the path 'C:\Program Files (x86)\Oracle\BI Publisher\BI Publisher Desktop\DotNet2007_2\Resources\field.png'.
at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath)
at System.IO.FileStream.Init(String path, FileMode mode, FileAccess access, Int32 rights, Boolean useRights, FileShare share, Int32 bufferSize, FileOptions options, SECURITY_ATTRIBUTES secAttrs, String msgPath, Boolean bFromProxy, Boolean useLongPath, Boolean checkHost)
at System.IO.FileStream..ctor(String path, FileMode mode, FileAccess access, FileShare share, Int32 bufferSize, FileOptions options, String msgPath, Boolean bFromProxy)
at System.IO.FileStream..ctor(String path, FileMode mode, FileAccess access, FileShare share, Int32 bufferSize, Boolean useAsync)
at System.Net.FileWebStream..ctor(FileWebRequest request, String path, FileMode mode, FileAccess access, FileShare sharing, Int32 length, Boolean async)
at System.Net.FileWebResponse..ctor(FileWebRequest request, Uri uri, FileAccess access, Boolean asyncHint)
--- End of inner exception stack trace ---
at System.Net.FileWebResponse..ctor(FileWebRequest request, Uri uri, FileAccess access, Boolean asyncHint)
at System.Net.FileWebRequest.GetResponseCallback(Object state)
--- End of inner exception stack trace ---
at System.Net.FileWebRequest.EndGetResponse(IAsyncResult asyncResult)
at System.Net.FileWebRequest.GetResponse()
at System.Deployment.Application.SystemNetDownloader.DownloadSingleFile(DownloadQueueItem next)
--- End of inner exception stack trace ---
at Microsoft.VisualStudio.Tools.Applications.Deployment.ClickOnceAddInDeploymentManager.DownloadAddIn(TimeSpan timeout)
at Microsoft.VisualStudio.Tools.Applications.Deployment.ClickOnceAddInDeploymentManager.InstallAddIn()
************** Loaded Assemblies **************
mscorlib
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.17929 built by: FX45RTMREL
CodeBase: file:///C:/Windows/Microsoft.NET/Framework/v4.0.30319/mscorlib.dll
Microsoft.VisualStudio.Tools.Office.Runtime
Assembly Version: 10.0.0.0
Win32 Version: 10.0.31119.0
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/Microsoft.VisualStudio.Tools.Office.Runtime/v4.0_10.0.0.0__b03f5f7f11d50a3a/Microsoft.VisualStudio.Tools.Office.Runtime.dll
System.Core
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.17929 built by: FX45RTMREL
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Core/v4.0_4.0.0.0__b77a5c561934e089/System.Core.dll
System
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.17929 built by: FX45RTMREL
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System/v4.0_4.0.0.0__b77a5c561934e089/System.dll
System.Windows.Forms
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.17929 built by: FX45RTMREL
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Windows.Forms/v4.0_4.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
System.Drawing
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.17929 built by: FX45RTMREL
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Drawing/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
Microsoft.VisualStudio.Tools.Applications.Hosting
Assembly Version: 10.0.0.0
Win32 Version: 10.0.31119.0
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/Microsoft.VisualStudio.Tools.Applications.Hosting/v4.0_10.0.0.0__b03f5f7f11d50a3a/Microsoft.VisualStudio.Tools.Applications.Hosting.dll
Microsoft.VisualStudio.Tools.Applications.ServerDocument
Assembly Version: 10.0.0.0
Win32 Version: 10.0.31119.0
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/Microsoft.VisualStudio.Tools.Applications.ServerDocument/v4.0_10.0.0.0__b03f5f7f11d50a3a/Microsoft.VisualStudio.Tools.Applications.ServerDocument.dll
System.Xml
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.17929 built by: FX45RTMREL
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Xml/v4.0_4.0.0.0__b77a5c561934e089/System.Xml.dll
Microsoft.VisualStudio.Tools.Applications.Runtime
Assembly Version: 10.0.0.0
Win32 Version: 10.0.31119.0
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/Microsoft.VisualStudio.Tools.Applications.Runtime/v4.0_10.0.0.0__b03f5f7f11d50a3a/Microsoft.VisualStudio.Tools.Applications.Runtime.dll
System.Deployment
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.17929 built by: FX45RTMREL
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Deployment/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Deployment.dll
System.Configuration
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.17929 built by: FX45RTMREL
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Configuration/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Configuration.dll
System.Security
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.17929 built by: FX45RTMREL
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Security/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Security.dll
System.Xml.Linq
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.17929 built by: FX45RTMREL
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Xml.Linq/v4.0_4.0.0.0__b77a5c561934e089/System.Xml.Linq.dll
Any help would be appreciated as I am not a developer just an Application Delivery person.
Thanks

copy disc to your computer and try to run setup file from there.
also, make sure your office dvd is working,

I am trying to load the 64 bit version of iTunes on to my PC but it continues to fail. My Pc is running Windows XP x64 edition. The rrror message states I need Window Vista 64 or later. What should I do?

I am trying to load the 64 bit version of iTunes on to my PC but it continues to fail. My Pc is running Windows XP x64 edition. The rrror message states I need Window Vista 64 or later. What should I do?

There is no version of iTunes that truly supports the 64-bit version of Windows XP and never will be. If you search this forum for "XP 64" or do a web search for something like "iTunes Windows XP 64", you'll find threads describing the process some people have used to "crowbar" iTunes onto XP 64, with varying levels of success, none of them complete.
Regards.

Windows 7 x64 Network Adapter Stops working on high load

My Network has been failing and it has been happening for about a month or so on Windows 7 x64. I dont think that the system configuration is the problem as it is happening on 2 seperate machines. One being a relatively beefed up "white" box, 4 gig OCZ ram, EVGA nForce 790I SLI Mobo, Q9600 Quad core processor, dual raid 1 - 150 Gig Raptors, 2 8800GTX SLI cards, Pure Power 800W PS. The second machine is an IBM Netbook S10. I use the Netbook as a media center connected to a Pioneer Elite 1050HD. One thing is I have a PS3 and have several 1TB Esata drives connected to an IOGear 3132 Esata 3.0Gb pciX card to my desktop.
My typical usages:
1. FTP from a private server
2. Streaming music via Winamp
3. Streaming video 720, 1080 from pc to PS3 via the PS3 Media Server
4. DLing demos or movies on the PS3
5. Network streaming a movie from the Esata drives to the bedroom or kids rooms
6. Streaming video from abc.com or southparkstudios.com from the Cox cable modem
7. RDC over VPN to work machines
Now I have noticed that when I am streaming HEAVILY, from any 2 of the above mentioned, my network connections will simply stop working with a yellow exclamation mark on the task bar network icon after a few moments, nothing in the event logs, no logs or ANYTHING at all. It will simply stop working no notifications or anything poof, gone. I have EVERY single patch, driver anything I can think of installed. Nothing works, the timing is completely random. FYI I have a NETGEAR ProSafe VPN Firewall FVX538 with a cable modem connection on WAN 1 and a cellular connection on WAN2, these have no impact I feel on the connections because the PC may go down or the Netbook will go down depending on which one has the most load. So this simply tells me that it it not a firewall router problem as I have tried using a cisco unmanaged 24 port 1GB switch and I get the same problems. From analyzing the systems and layout I am led to believe that it is either a network adapter driver OR a Windows 7 problem (collisions, unhandled exception?), this NEVER happened with XP or Vista. I have tried everything but a new network adapter, I have tried the secondary adapter card on the mobo, I have tried bridging the two, I have tried daisy chaining the switch and putting each machine on its own dedicated switch linked to each other with no change. When the network goes down it is only that box effected, all other machines still connect to each other fine, only the one with load shuts down and the only ones that shut down are Windows 7. These machines are all wired with commercial cat5e patch cables, they have all been swapped for new ones lately. All networking and PC equipment are on UPS so I doubt voltage variations. Windows Firewall is disabled I only use the hardware firewall, I do not use any antivirus.
I am completely out of options, can anyone recommend a new route?
In addition when I go to the command prompt and attempt to do an ipconfig /release. I get an error saying that the adapter is not in a usable state. Very irritating, this forces me to reboot, or right click disable/enable on the network adapter. The right click route takes almost a minute to complete.
Tried update driver in nvidia control panel, no luck. I have also turned off the networking power saver option in the adapter settings.

Hi,
Considering this issue occurs on 2 different machines, I also think this issue may be more hardware related. You may also try the following:
1.    If the computers are connecting to a router, please ensure the router’s firmware is up-to-date.
2.    Please run the following command in an elevated command prompt in Windows 7:
netsh interface tcp set global rss=disabled
netsh interface tcp set global autotuninglevel=disabled
netsh int ip set global taskoffload=disabled
3.    Disable SNP in Windows 7 by setting Registry as following:
Note: Please perform a full-system backup first.
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters]
EnableTCPChimney=dword:00000000
EnableTCPA=dword:00000000
EnableRSS=dword:00000000
If the keys do not exist, please create them and assign the value.
An update to turn off default SNP features is available for Windows Server 2003-based and Small Business Server 2003-based computers
4.    If the issue persists, please add another network adapter to this computer and see how it works.
Hope this helps. Thanks.
Nicholas Li - MSFT
Hi, I'm experiencing a simular problem here.
My PC was using Asus P5Q-E motherboard but exchanged it for Asus P5Q TURBO Pro because it loses 'connectivity ' after an interval between a few hrs to 26hrs. During this state, I can't browse or my Outlook to check emails. The only thing that can send/receive data is Vuze. Plus, the strange thing is that the network icon says there's nothing wrong at all (when it obviously there is). Even the currency desktop gadgets says the time elapsed since it 'lost connectivity '.
I initially thought P5Q-E was faulty so now I'm using the TURBO Pro. However, the problem still persisted.
I am using Win 7 Ultimate x64 with all the updates and drivers. Connected via LAN cable to the router and the firmware is the latest. My ISP sent me a replacement router to confirm that their equipment is not faulty, which is true.
I have tried the above methods 1-3.
Although I'm not sure if I implemented Method 3 correctly since I don't usually go to the registry but here's what it looks like after creating it:
EnableRSS   REG_DWORD   0x00000001 (1)
EnableTCPA REG_DWORD   0x00000001 (1)
EnableTCPChimey REG_DWORD   0x00000001 (1)
There are 3 more PC's and 1 laptop in the house. 2 PCs use Win XP, 1 uses Win 7 Ultimate x64 and laptop uses Linux Ubuntu.
My PC has a second OS, Linux Ubuntu, I used it to time trial both motherboards (before and after switching) and found no problems at all even after 48hrs, so it confirms it's not a hardware issue.
The other PC's apart from mine are connected wirelessly. As far as I've been told, they don't experience the same issue I have.
I've been trying to tackle this problem for months now and I'm frustrated to reboot my PC every time it 'loses connection '.
I chatted with Asus about the issue when I still had the P5Q-E mobo, they said that they built a simular system to mine with the same mobo and said they couldn't reproduce the problem I'm having. THey even tested on other mobos with the same LAN chip and found nothing wrong. That's why I got the TURBO Pro that has a different LAN chip.
Anyone got anymore suggestions???
Thanks in advance.

Could not load file or assembly 'Oracle.DataAccess' Windows Vista x64

Ok now here is the funny part, this works fine when i'm developing ASP.NET applications ( i assume that is puts the dev web server into x86 mode), but when im trying to use Oracle.DataAccess DLL in a console application i get a '+Additional information: Could not load file or assembly 'Oracle.DataAccess, Version=2.111.6.20, Culture=neutral, PublicKeyToken=89b483f429c47342' or one of its dependencies. The system cannot find the file specified.+' error in visual studio when i try and debug and also when i try and run the console app.
Using the latest ODP.NET 11.1.0.6.20, Windows Vista x64 SP1 (all updates installed), Visual Studio 2008 SP1

never mind, figured it out, the Platform target in studio was on "Auto" and was defaulting to x64....

I was running Lightroom 3.6 with the OS Windows XP (Sp3). The whole system crashed, I am unable to recover the serial number. I then upgraded my OS to Windows 7 (x64) and down loaded Lightroom 4.4, I wanted to buy a licence so I then upgraded to Lightroom

I was running Lightroom 3.6 with the OS Windows XP (Sp3). The whole system crashed, I am unable to recover the serial number. I then upgraded my OS to Windows 7 (x64) and down loaded Lightroom 4.4, I wanted to buy a licence so I then upgraded to Lightroom 5, now when I try to register I am asked for the original licence/serial number. Where do I go from here??????

If you upgraded from 3.6 to 5 (you didn't indicate buying 4.4) then you will need the serial number from 3.6 in order to be able to use 5. If you did not keep a record of it there is a chance it might be available thru your Adobe account online, but if not, there is likely not much you can do except to return the upgrade and purchase a full version. Try contacting support using chat and explain your situation to see if they can help.
Serial number and activation chat support (non-CC)
http://helpx.adobe.com/x-productkb/global/service1.html ( http://adobe.ly/1aYjbSC )
If you did purchase 4.4 then that should be sufficient to use to activate 5.
I can never be sure what goes on with Lightroom, and the Adobe site (even when it works properly) makes finding information about products difficult these days so I am at a loss to confirm anything I say.

MBP Retina Windows 7 x64 drivers will not load

I knew nothing about Mac or OSX and got my MBP running in July.
Then later I realised I shoudl take advantage of the Solidworks capacity to run 64bit so I removed partition, got the ISO, made the Flash USB, installed Windows 7 x64 and it is now installed.
But none of the drivers copied in. I used the latest updated Bootcamp 4.0.4 and really the first time I did this everything worked when I installed Win 7 x86 and the pc just started in Windows perfectly all drivers working (except the tap function on trackpad did not work).
I did everything according bootcamp instructions but no luck this time the drivers did not go in (i think)
Now my new windows 7 x64 is exactly as per my installaion disk W7 Sp1.0 x64 all there but absolute disaster the screen is not recognised I cannot even start to get the wireless working so no network no internet no help.
I tried to run the setup.exe from the USB ( where Bootcamp made directorories and copied nicely all the files etc etc) as per the printed copy of the bootcamp installation guide (printed copy on hand) but no success
What now please help?

(bump) I have a similar issue. Win7 installed fine but I have a few hardware drivers which did not load, particarly the wifi driver.
Anyone know how to handle this?
Thanks-

Windows 7 x64 Pro, desktop GUI fails to display correctly, or crashes, when High RAM load, and even after. HW changed, same issue. Please Help.

Hi Guys,
I have have this horror issue with my PC. I have even changed the hardware configuration and the problem still persists. My PC fails to display the desktop correctly after using highly RAM intensive applications, especially Chrome, but even after getting
the chance to close it, or waiting for it to crash by itself, the PC is still not able to display correctly the GUI, even on other browser/applications as shown in the screenshots.
1st Hardware Config:
Intel Core2Quad Q9450
4x2GB DDR2
MSI P43 motherboard
Ati Radeon x550 video card
Software used, that seemed important for me to mention:
NOD32 v4.2
Comodo Firewall 5.12
Chrome
Screenshot Captor
SpeedFan
Other mentions:
Aero is disabled, because I've considered that it's one of the causes.
So, I've considered that it's a RAM issue or a videocard issue, and I've upgraded to:
Intel Core i7 3770k
4x8GB DDR3
Asus P8Z77V-LX motherboard
Intel GPU integrated in the 3770k CPU
The problem just happened 2 times on this rig also, and the RAM was not even coming close to it's maximum capacity of 31.7GB. It was at ~20GB's.
Also, this is another videocard(Intel's integrated GPU), so we can exclude the videocard from the suspects.
My suspects:
1) some desktop manager bugs, or other similar issue
2) video memory allocation - I'm still suspecting that it can be caused by the amount of RAM dedicated to the videocard, currently, I think that it is at 256MB.
3) some poorly designed components of Chrome/Screenshot Captor - still very questionable since there are enough resources on this system, so there should be no fight over resources. And when the system is barely used there are no issues.
4) Adobe Shockwave Flash - maybe this one????
I have attached a set of 20 screenshots here, these were taken on the 1st configuration of my PC, using Q9450:
http://imgur.com/a/Mc8hI#4
Notice how it distorts the image by duplicating it and showing it in a smaller space, or how does it displays those black rectangles. In those moments, the PC is fully functional(the apps are running the background), without being slowish or something, but
you can hardly control it like that. For example, I've tried to remove the mouse from the USB, and then I've insterted it back, the image was not displayed correctly, but the mouse was recognised instantly and the pointer was controlable.
Same thing still happens on the new configuration. Please advise me.
LE: OS is Windows 7 x64 SP1 Professional and it's Geniune. There is no cracked software on this PC. No games. I've tried to maintain it as clean as possible.

Hi,
First, please be ensured that you have installed the latest drivers and all the updates.
Then check whether this issue will not in
Safe Mode. If it didn’t occurred, I suggest you narrow down the cause in
Clean Boot mode.
In addition, try to create a new profile to see how it works.
Hope this helps.
Vincent Wang
TechNet Community Support

Windows 7 x64 - No Drive Detected. Please Load Mass Storage Driver........

Hi there..
I just installed a new harddrive on my MacBook Pro (a Samsung SpinPoint M7 Enhanced 640GB)
I formatted it to HFS+ during Mac OS X install, and it works great.. Later on I made a partition, using Boot Camp and began installing Windows 7 x64, only when I come to the screen where I need to pick a partition, there is none..
It doesn't seem to find a HDD and asks for a 'Mass Storage Driver'
Does anyone have an idea of how to solve this problem?

Hi Fortuny, and thanks
The Windows Install disc is retail, the same disc I used to install Windows 7 on my old hard drive via boot camp..
Usually I don't have any issues with this stuff, I've tried it a couple of times helping my friends, but since I changed the hard drive from the standard 320 GB FUJITSU MJA2320BH FFS G1 to a 640 GB Samsung SpinPoint M7 Enhanced (HM641JI) It just doesn't seem to detect it during Windows 7 Install..

Windows 7 x64 on 2009 MB, step-by-step instructions and solutions

ok, after spending days on this with about 10+ clean installs on 2 different machines and searching forums about various problems, i'm going to go step by step in a flow-chart like manner to describe the steps and various pitfalls in getting windows 7 ultimate 64 bit installed correctly on a macbook (late 2009)...most of this i didn't figure out on my own, this is a compilation of solutions found by others. i'll try and link or credit anyone i can, but honestly can't remember where i saw all of this. part of this is to share my days of frustration to try and save someone some time. also, in case i have to do this again, i want a record of it so i don't have to start from scratch next time.
i don't have everything working perfectly, but i have wireless and sound, but not sure if all the drivers are up to date. i'm still working on the headphone issue, i don't have sound yet with headphones, but i got the speakers to work.
i'm going to preface this by saying that windows 7 is a horrible piece of software, i'm only helping a friend do it because she's an architect and needs autocad, but she wants a mac for daily use. also, i'm doing this from a spanish install of windows 7 (here in south america), so it's a pain to translate this cruddy convoluted OS into english as i'm not familiar with windows 7 anyway, so i'll do my best. i'm not a pc expert. also going to say that the windows 7 x86 and x64 installs i've done on a couple macbook pro 15's seems to work much better (full trackpad functionality, expose works) and without as many problems...i don't know why it doesn't seem to work as well in x64 on the macbook, i'm still investigating.
also, i want to say that a fresh (first-time) bootcamp partition with windows install after a clean mac os x install seems to produce the best results. i say this because i wasn't happy with all the hacks in my first couple attemtps, so i erased the bootcamp partitions and re-created them to re-install windows 7 again. but i started experiencing some peculiarities that never happened in the first install after a clean Mac OS X install. it's as if the computer leaves artifacts from previous installs and acts funny. also, reboots and start-up times seem to be slower now than when it was a first-time fresh install. anyway, i'll try and outline all the weirdness here, indicated by asterisks *
SO, HERE GOES:
1) Go to Bootcamp Utility > Create Bootcamp partition
2) Afterwards, this should take you to a restart into the windows install dvd....if install dvd boots fine, skip to step 3
** if you get a gray screen (happened to me after subsequent re-install attempts), you have to power off and reboot holding down "C" key to boot from the dvd...or you can hold down alt/opt key to get the icons of bootable volumes, at this point it should be mac os x and the windows dvd. the point is, force it to boot from the dvd if it hangs on re-start.
3) Windows install should start. Select language, etc....You should then get to a screen listing all the partitions (should be 3 of them). Choose the Bootcamp partition and format (erase) it to proceed with the install.
4) Windows should start installing all the files and will reboot a couple times, here's where things get weird possibly. On the first attempt at installing Windows 7, the install went smoothly on restart.
** some of you might get a blinking cursor and a black screen that goes on forever. Supposedly this is a bug in Windows 7, having to do with video drivers or something. I don't understand because my first install attempt, it rebooted just fine and the installation continued.
anyway, what you have to do here if you get the forever-black screen is power down the machine with the power button and restart holding the alt/option key. this time when you get the bootable volumes on the gray screen, choose the Windows partition, which will now appear. DON'T boot up from the DVD. upon restart into Windows, you should be back in the installation process and it will attempt to finish the install here.
it might be my imagination, but once i had to reboot into the dvd here to actually finish the install. technically Windows is not finished installing at this step, you just have to figure out how to get past the black screen to finish the install. try both.
5) Windows should go back to where it left off before the restart, then finish the install.....and restart AGAIN. On my first attempt, the restart went smoothly and started the "first time user" process...
** some of you will get the black screen YET AGAIN, this happened to me on my subsequent attempts at re-installing Windows. again, you need to power off and start up holding the alt/option key, choose the Windows partition and it should take you to the "first time user configuration" process....since at this point, windows is indeed installed.
6) Here you will fill out all your information, product key, etc...and get into Windows. Here you will have some other problems.
Problem #1: you have no drivers to run Windows on your Mac, so you will need to install Bootcamp in windows from your Mac OS X install dvd
Problem #2: you have no "right click", because you don't have drivers, so you might not be able to eject the Windows dvd to put in the Mac dvd
Solutions: you can't control-click or right click, BUT YOU CAN hover over the DVD drive ( "D:" in your computer, my PC or whatever it's called in english) and see if there's an "eject disc" option.
for some reason, my Windows dvd was spinning and not being recognized, so i just rebooted (alt/option) into Mac OS X and ejected the disc there. the point is, you need to eject the Windows disc and put in the Mac OS X install disc to access Bootcamp for Windows.
7) Reboot into Windows (if you had to boot into Mac to eject the disc). Insert Mac OS X install disc. Navigate to BootCamp setup.exe and run it.
** the first time i did this, it ran no problem. but in subsequent attempts, it gave me the "x64 not supported by this computer" message that everyone seems to encounter. there is a bypass for this outlined here:
http://www.techulous.com/hardware/how-to-apple-boot-camp-64-bit-for-windows-7-on -unsupported-macs.html
8) Ok, so now you should have Bootcamp 3.0 installed. Now you need to update it with Bootcamp 3.1 update. Download it here and run it. This is required for 64 bit support, I believe this is the link:
http://support.apple.com/kb/dl979
** hopefully you don't have problems, i didn't, so you might have to search the forums since i can't anticipate what might happen here, it worked for me every time.
9) Ok, i think it might reboot after the update install. Now you have Bootcamp installed and most of the drivers you need, however not everything works. Some of the drivers will be out of date.
Problem #1: you may or may not have updated nvidia drivers. mine are ok, but check nvidia website if you have doubts. most of their drivers are for PC hardware, however, so the ones on the bootcamp disk and update should be fine.
Problem #2: almost everyone has wi-fi connectivity problems. it has to do with the wrong/outdated broadcom drivers from bootcamp. i will outline how i got it to work (based on someone else's solution i found in some forum or other).
Problem #3: almost everyone is having sound issues. i'll explain what i did. i still have no sound coming out of the headphone jack, i'm working on that next. but i have speaker sound and no red light coming out of the headphone jack.
** first of all, you should probably download firefox from internet explorer in windows, then update adobe flash, it's a pain....i used another computer to download the drivers, then transfered them by USB drive, but you can do it however u want.
Solution to wi-fi: ok, not sure where i got this information, but i downloaded HP drivers in a file called "sp45524.exe"....here's the link:
http://www.wireless-driver.com/download/hp/hp-broadcom-wireless-lan-windows7-dri ver-v560188.htm
apparently the broadcom drivers in Bootcamp 3.0 and 3.1 update won't install on Windows 7 x64 for some reason, lot of people are getting "code 10".
what i did is this:
9a) run the .exe file, it will create a folder called SWSetup\SP45524 that will house the drivers. there's a setup file in that folder, i didn't try it. perhaps it will install from there, but everything i read suggested a different step. ** if you run the set up file, you may have to run as administrator, or use the "troubleshoot compatibility" trick to get it to work.
9b) Go to Control Panel > Hardware and Sound > Device Manager > Network adapters
you should uninstall or deactivate any drivers you have. if it's not showing any wi-fi adapter, right click and "check for new hardware" (not sure how it's translated into english from spanish)....you should have an unknown device pop up with the yellow icon and exclamation mark. double click on that, assign it as a network adapter.
when you get to the driver tabs, you can install it from there. this is where it gets tricky. click "install driver", "check drivers on this computer", "choose from a list of drivers on this computer", "use disc", and in the dialogue box ("install from disc" that says "copy manufacturers files from", navigate to the C: SWSetup|SP45524 folder and click until you can accept. this will load up a different list of drivers.
(sorry, i'm translating the Windows from spanish to english, and i'm not familiar with exactly what they say in english, so you'll just have to use your imagination)
you should now have a small list of drivers. personally, i chose the first one on the list "Wi-Fi adapter Broadcom 43224AG 802.11a/b/g/draft-n", but the second one worked also. again, i'm doing this on a late 2009 white macbook (6.1) and it works. according to the date of the driver, it seems like it might not even be the most current and might be older than the one that's on the MAC OS X install disc, but none of the ones on the disc work. this one does. (thanks to whoever found this out, i can't find the original link of the post with this driver reference).
Solutions to sound: ok, there are multiple posts on this, everything from updating realtek to sigmatel...personally what worked for me was to download the most current Cirrus Logic drivers.
everyone has been pointing to this post:
http://www.stuffedcow.net/macbook_audio
it doesn't really tell you what to do exactly. i'm not even sure what to do, but here's what i did. actually, i downloaded what was supposed to be the CS4207 driver here:
http://www.cirrus.com/en/products/pro/detail/P1233.html
then i followed the same procedure as before with the network adapter driver...."install driver", "check drivers on this computer", "choose from a list of drivers on this computer", "use disc", and in the dialogue box ("install from disc" that says "copy manufacturers files from", navigate to the folder you just downloaded from the above link.
you should have an updated list of drivers. what i don't understand is that the Cirrus site lists the most current driver as CS4207, but the only thing that has 4207 in it starts with CDB. in any case, i chose the last one on the list, CS4206A (AB 99).
i have no idea why i chose that, it just seemed to be the most current. in any case, sound works now.
Ok, i tested all this stuff in skype. wifi, microphone and speakers work, isight works. however, still no headphone sound. so if anyone knows how to fix that, please let me know. i haven't gotten to that part yet. but i've spent like over a week trying to figure this out. windows 7 is so horrible that there seems to be so many steps to getting it just right, and i just found myself starting all over (i didn't mention the nightmare with license breaks with AutoCad due to windows reading the clock differently...that's another hack that i had to deal with...and failure meant re-installing everything).
ok, off to bed now....

Windows 7 x64 all updates
Just doublechecking. Does that include the recent chkdsk hotfixes?
[The Chkdsk.exe program does not start correctly on a Windows 7-based computer|http://support.microsoft.com/kb/975778]

VS2005 Crystal Report Print Report Button is not working on Windows 7 x64

Hi There,
My application is written in VS2005 C# on x86 machine. It runs smoothly on XP pro and Vista x86 machine.
I deployed the same to windows 7 x64 machine with CRRedist2005_x64.msi and found that the Print Report button is not working.
So, I re-compiled my application to x64 target platform, and reinstall the application to the same machine. But nothing changed. I have surf for answer over the web but nothing found.
Please help urgently. Any helps is much appreciated. Thks in advance.
Edited by: chanpyvivian on Mar 26, 2010 11:14 AM

I follow your instruction as below:
1) download the sample app vbnet_win_printtoprinter.zip to dev computer and compile it to .NET 2005.
- Run from my dev computer
- Click "Print Report" button
- Error message display - please see below
    The error was due to the default printer name hard coded in the program was not found. I have edited to my printer name and it can be printed out with no error.
2) Use a "saved data" report so that you do not have to worry about database logon.
can't find the "saved data", please elaborate
3) Then copy the exe to the 64 bit box and try to print using this sample app.
-do you mean copy the exe to the 64 bit computer for testing ?
ERROR Message
CrystalDecisions.CrystalReports.Engine.InvalidArgumentException:
Invalid printer specified. ---> System.Runtime.InteropServices.COMException (0x80000201):
Invalid printer specified.
   at CrystalDecisions.ReportAppServer.Controllers.PrintOutputControllerClass.ModifyPrinterName(String newVal)
   at CrystalDecisions.CrystalReports.Engine.PrintOptions.set_PrinterName(String value)
   at CrystalDecisions.CrystalReports.Engine.PrintOptions.Copy(PrintOptions src)
   at CrystalDecisions.CrystalReports.Engine.ReportDocument.Load(String filename, OpenReportMethod openMethod, Int16 parentJob)
   --- End of inner exception stack trace ---
   at CrystalDecisions.ReportAppServer.ConvertDotNetToErom.ThrowDotNetException(Exception e)
   at CrystalDecisions.CrystalReports.Engine.ReportDocument.Load(String filename, OpenReportMethod openMethod, Int16 parentJob)
   at CrystalDecisions.CrystalReports.Engine.ReportClass.Load(String reportName, OpenReportMethod openMethod, Int16 parentJob)
   at CrystalDecisions.CrystalReports.Engine.ReportDocument.EnsureLoadReport()
   at CrystalDecisions.CrystalReports.Engine.ReportDocument.get_FormatEngine()
   at CrystalDecisions.CrystalReports.Engine.ReportDocument.PrintToPrinter(Int32 nCopies, Boolean collated, Int32 startPageN, Int32 endPageN)
   at PrintToPrinter.Form1.Button1_Click(Object sender, EventArgs e) in C:\Crystal\CRNET\vbnet_win_printtoprinter\vbnet_win_printtoprinter\Form1.vb:line 91
OK
Edited by: chanpyvivian on Mar 30, 2010 6:18 PM

I can register an OCX file in Windows 7 x64 without incident but with Windows 7 x32 I get a p-up that says "DllRegisterServer failed with error code: 0x80004005. What gives???

Hey yeah. not much else to say. The title says it all.
I'm trying to register an OCX file that my video editing application requires to work properly.
I'm using a Registry (Regsvr32 and Regsvr64) tool to Register DLL/OCX files. Both bit Registry tools work fine. I can Register any DLL or OCX file with Windows 7 x64 and everything goes smoothly.
But, when in Windows 7 x32, again, no problem with merging the Regsvr32 tool, but when I go to register the OCX file message says it was loaded but the DllRegisterServer failed with error: 0x80004005.
Why does everything work in Windows 7 RC 7100 x64 but not in Windows 7 RC 7100 x32???GA P35 DQ6 Mb, Intel Wolfdale 8600 3.33Ghz C2D CPU., 4x2Gb Mushkin DDR2 1066 PC2 8500 Ascents Memory Mods., PNY-nVidia GE Force 8800 GTS (640MB), 4-Western Digital Caviar SATA(2) HDD's (internal), 1 EIDE-USB External; Hauppauge PVR 1600 TV tuner, Dual Monitor: (1) Standard up top, (1) WideScreen below; Altec Lansing Speakers. Here Kitty, Kitty...that's my Kitty Kat, he's a Kat, because he is kat...kat.

I don't know what happened.
My Video Editing software was working fine a few days ago in Windows 7 x64. Tried using it this morning....couldn't load the .mpg video clip. Just stood there looking stupid like it does in the 32-bit version of Windows 7.
I was hoping the x64 version of Windows 7 RC 7100 was going to make a decent run against my XP Pro SP3 setup. When I was able to register the required .ocx file for the video editing application, I thought "cool". I made a TV recording then used the Video Editor to edit it and it worked fine. Earlier this morinng I made another TV recording, went to go edit it and the video editing application couldn't load the .mpg file at all. This problem just annihilated any chance of me ever purchasing Windows 7, 32 or 64-bit.GA P35 DQ6 Mb, Intel Wolfdale 8600 3.33Ghz C2D CPU., 4x2Gb Mushkin DDR2 1066 PC2 8500 Ascents Memory Mods., PNY-nVidia GE Force 8800 GTS (640MB), 4-Western Digital Caviar SATA(2) HDD's (internal), 1 EIDE-USB External; Hauppauge PVR 1600 TV tuner, Dual Monitor: (1) Standard up top, (1) WideScreen below; Altec Lansing Speakers. Here Kitty, Kitty...that's my Kitty Kat, he's a Kat, because he is kat...kat.

Using USB for Bitlocker in a Bootcamp install of Windows 7 x64 Ultimate on early-2011 Macbook Pro

First of all some details on my current setup:
Macbook Pro 15" (early 2011) with a i7 QM processor and 8 GB RAM, Superdrive and HD installed
Mac OS X 10.7.3
Windows 7 x64 Ultimate in a Bootcamp setup
Existing partitions on HD are EFI, MacOS X, Bitlocker Startup, Windows
I removed "Recovery HD" after creating DVD image contained in latest Lion installer from AppStore.
What I got so far:
It took some time to find a way for Windows getting a second partition to be used for Bitlocker startup files. Using existing partition layout I replaced previously existing "Recovery HD" partition for Bitlocker partition in Windows (after taking dd-based image of Recovery HD).
Recently I tried to enable Bitlocker and continued to fail on Bitlocker System Check claiming to have no access on USB while booting. And that's my issue ...
I read about using Windows' diskpart to have a GPT partitioned USB stick containing single NTFS partition. I tried to achieve the same with disk management in Mac OS X though it was creating a hybrid MBR/GPT setup that wasn't recognized by Windows at all. Then I tried partitioning in Mac OS X to have GPT partitioning, used Clonezilla Live CD's gdisk to apply hybrid setup another time. I even tried to do the whole partitioning in Linux using gdisk, but Windows still didn't recognize the formatted partition on USB stick then. So, the only way found is using diskpart in Windows to get a GPT-based USB-stick with a single NTFS partition.
I put my startup key there (attributed as hidden, system file) and tried to restart several times. On every boot Windows is prompting for inserting valid startup key as it wasn't found. The partition is encrypted already and entering the printed 48 digits recovery key gets me in every time.
If I keep the stick inserted the boot is noticeably delayed, but it's instantly continuing as soon as I unplug the stick. So there is something processing the stick ... I tried different sticks, but hope it's not related to using one special stick since they are used to support similar (equivalent) interfaces, aren't they?
Don't tell me about using TrueCrypt or similar as I prefer to use existing software instead of adding 3rd-party software doing things the same way. And for True Crypt USB must be readable at boot as well. And previous trials with different approaches rendered all failing at some point of setup. Finally, I don't want to reinstall existing Windows as it keeps me from working even more.
Found some post regarding trouble with Lion installations (e.g. I can't use rEFIt ... it simply didn't show up and this seems to be related to using Lion), found the KB article of Apple on preparing USB external storage for use at boot, but all troubleshooting hints didn't help.
What the heck is wrong with this setup?
EDIT: There is no problem to have Bootcamp starting previous Recovery HD partition now Bitlocker startup partition instead of originally prepared Bootcamp partition, which is encrypted now. This is in contradiction to other posts here. I'm sure Apple support isn't best choice to ask for support as this problem is MS specific and thus Apple won't care that much ...

Well, I've seen lots of those threads as well and most failed to manage cooperation of Bitlocker and FileVault, have trouble to get a second partition for windows to use with bitlocker or truecrypt etc. But these issues don't apply to me anymore.
Next there are threads instructing how to get a USB stick to work with Bitlocker claiming to have GPT instead of MBR so EFI is gaining any access on them. Those cases seem to work with MacBooks running with Windows, only, thus passing the issues mentioned in paragraph before as well.
And there is my confusion originating from: I can remember some sites claiming to have trouble with EFI on a Mac using Lion, but all those sites are older than Lion's final release date. So I don't know if there is a similar issue today or if I'm actually missing some option ... rEFIt isn't working with Lion according to the refit site itself. Some sites claim EFI is behaving differently on whether there is a super drive or not as Lion isn't supporting USB booting as long as booting from DVD/CD is available ... what's true about those facts? Is my problem related to having a super drive? Are things getting better as soon as I'm replacing my superdrive by a second internal drive? Is it that strange or some sort of plausible behaviour?
According to GPT, Windows 7 is obviously failing to properly detect hybrid MBR/GPT setups on USB sticks while that's what MacOS' disk manager is doing on having GPT-based single partition stick with exFat format. Instead of using the second hybridized partition it's accessing the protected part, only. If I'm converting a disk to GPT in windows everything works fine, but then without hybridized MBR ...
Regarding the fans I'm with you ... as soon as processor load is exceeding 5% the fans get quite noisy ...

LaserJet 1020 Windows 7 x64 driver not working!

Hello. I have problem. I have recently installed Windows 7 x64, and when I tried to install driver for my LaserJet 1020 from this site, an error appeared.
First, when I launched the driver installer, I agreed with license agreement and proceeded. Than, loading bar appeared, it came to 3 division sticks in it and text above was like "Preinstalling the driver files". Then, suddenly, for a split-second "Copying files to the hard drive." text appeared, than again "Preinstalling the driver...", and it appeared again for less than a second, and again, and again... Than, after a few times, it just crushed, with Windows message "Printer Software Installer" is not working".
And one more: in Program Files -> HP folder there are lots of driver files (which seem not to be working) and another HP folder with same file and HP folder in it... Recursion of some kind, I think.
So, what should I do? I can't use my printer for a long time because of this driver!
I'm haven't spoken English for a while, so, if I explained something strange, ask, I'll try to explain better =)
This question was solved.
View Solution.

Who is awesome? I'm awesome! ^_^
I used russian version of the driver, worked flawlessly =)
Take it from here. Glad, if I could help =)
http://ftp.hp.com/pub/softlib/software11/COL22237/bi-58689-4/lj1020_1022-HB-pnp-win64-ru.exe

Fresh Install Windows 7 x64 IE 9 Flash Player Crash

Greetings All,
I am working on a major imaging prject for my organization. I'm getting ready to create a new image for some of our machines so I was getting the reference computers ready. I have noticed that when flash player is enabled in IE 9 it crashes the browser. I get the "Internet Explorer has stopped working" error. I can click the close program button, IE will try to launch the same page again and i get the error again with a bar on the bottome of the IE window stating "A problem with this webpage caused Internet Explorer to close and reopen the tab". After a few rounds of this I get the "Internet Explorer has stopped trying to restore this website." This is occuring on two different machines that I have been preping.
Here are the details of what I have done to these machines: (Dell E6420 and Dell E6320)
1. Installed Windows 7 x64 from install media (blanked the drive so fresh install)
2. Installed SEP 11.0.6200.754
3. Installed all drivers fresh off of Dell's website.
4. Installed Office 2010.
5. Ran and updated EVERYTHING from MICROSOFT update, SP1 and IE 9 included.
6. Went to Adobe.com and installed the latest Acrobat, Flash, and Shockwave Player from the links on the main page.
7. Rebooted and now anytime I go to any page with Flash objects I get the above error.
Here are version:
Windows 7 x64 SP1
IE 9.0.8112.16421
Shockwave Flash Object (Enabled in Manage Add-ons) 10.2.159.1
As said these are two brand new machines, two fresh loads, two batches of software fresh from the web, and two machines having unacceptable problems when Flash is installed. What's up here?
Many Thanks for your time!

I’m going to take a moment and do two things, bump the thread, and provide a short synopsis on where we stand on this issue.
After much trial and error and the help of Chris I can say with relative certainty that this is an issue with compatibility between nVidia’s Optimus systems and Flash player’s hardware acceleration feature. I don’t know if the issue is just IE9 or IE8. I haven’t taken the time to try this on an Optimus system with IE 8 yet. If someone out there is running one of the Optimus enabled laptops with IE8 and the latest flash installed I would love to hear some feed back.
Ultimately IE8 vs. IE9 is an inconsequential issue. Soon Microsoft will start pushing IE 9 as an important update meaning that the problem will need to be fixed or we’ll be faced with more users having the problem.
I have posted about the issue in the nVidia forums, Dell forums, and Adobe forums. Please find the links to the threads below. I don’t believe the issue to be unique to just the two Dell models that I am dealing with. I have run across numerous complaints along this line from several different OEMs.
Here are some links of interest if you want to research and lend your voice to the cause:
Dell Forum Threads:
http://en.community.dell.com/support-forums/laptop/f/3518/t/19376814.aspx
http://en.community.dell.com/support-forums/laptop/f/3519/t/19376823.aspx
nVidia Forum Thread:
http://forums.nvidia.com/index.php?showtopic=199537
General Information on Optimus Systems:
http://www.nvidia.com/object/optimus_technology.html
nVidia thread where they admit a flash issue and promise a pending driver update (some months ago):
http://forums.nvidia.com/index.php?showtopic=191020
Good luck all!

Loading Windows 7 x64 on H520s

Similar Messages

Maybe you are looking for