Local Calling Area

Why, with all the technology Verizon so proudly touts in all its commercials, can we not find out our local calling area on the web site? Instead, we're directed to go look it up in the paper phone book. Give me a break. It's all stored away in a database somewhere and it's really a no-brainer to allow access to it. Honestly, that is just completely lame in this day and age.

Thats a great idea! This would be a perfect candidate for the Verizon Idea Exchange. Please search on the idea exchange and cast your vote. There may be another member who made the same suggestion. If not, please add a new idea so your fellow community members can comment and vote on your suggestion. http://forums.verizon.com/t5/Verizon-Idea-Exchange/ct-p/ideaexchange . The Verizon Idea Exchange is there for you to submit your ideas and suggestions to Verizon so that we can consider them as we innovate our products and services.
Anthony_VZ
**If someones post has helped you, please acknowledge their assistance by clicking the red thumbs up button to give them Kudos. If you are the original poster and any response gave you your answer, please mark the post that had the answer as the solution**
Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or plan

Similar Messages

ANOTHER Step BACKWARDS - NO, You CANNOT SEE Your LOCAL Calling Area ONLINE !!

Why check your LOCAL calling area? TO SAVE Yourself MONEY. If you can check the calling area quickly, you can tell if it will be a TOLL CALL. Sure, this is not an issue depending on your calling plan. It is to a lot of folks like me; and you may be calling from a different phone at times.
Up until at least January 2008 you could EASILY determine your LOCAL CALLING AREA on Verizon's website by entering your phone number. The link WAS
http://www22.verizon.com/CallingAreas/localCallFinder/LocalExchangesList.htm , but NO MORE.
I SUSPECT it was discontinued because Verizon realized that by making a MONEY-SAVING 'device'
easily available was NOT GOOD FOR THE BOTTOM LINE.
I went thru all of Verizon's hoops to get an answer, but they have their roadblocks firmly planted.
Their is A LOT OF JUSTIFICATION for CONSUMER REPORTS to give its highest ratings to Verizon's SERVICES...... WHILE AT THE SAME TIME RATING THEIR CUSTOMER SERVICE "DREADFUL".

Hi GimmieDps,
I'm sorry you are having difficulty with your calls from home. I have escalated your concern and an agent with access to your account will reach out to you directly by email, private message in the Forums and/or the billing telephone number on your Verizon account for more information or to help you resolve your issue.
Regards,
SunshineF

What Prefixes Are Included In My Local Calling Area?

I am in the former GTE service territory, specifically, the Elsinore Main California exchange.
On Friday, December 11, 2009, I spoke with a service representative and a supervisor (who admitted that she was "filling-in" and is really an hourly employee), who are in the soon to be divested Everett, WA call center.
I was calling to find out what prefixes are included as part of my local calling area, specifically ZUM 1 AND ZUM 2 (some also call it Zone 1 and Zone 2, but the correct designation in most southern California service areas of Verizon is ZUM).
Both representatives had no idea what a "ZUM" is, and the "supervisor" said she had never heard of the term ZUM or Zone.
What made me upset is that I was told that they (Verizon) did not have this information, and I would have to contact the CPUC (California Public Utilities Commission) to obtain this information as Verizon's staff would not have it.
My reply was how would Verizon not have the information, because they would need the ZUM prefix list for each exchange so they could bill correctly.
I then asked how does Verizon gather all the calls that are made from their exchanges each month and send this data to the CPUC so that Verizon can then determine if the call is ZUM 1, ZUM 2, ZUM 3 or intralata or interlata?
The "supervisor", said yes, because Verizon would not know what prefixes are included, and relies upon the CPUC to review the calls from Verizon's exchanges and prefixes so that Verizon can bill their customers each month, and this has been the process for many years (according to the "supervisor").
I kid you not, this what was said to me by the Verizon representatives, and I shoulld have advised the employees that I was recording the call. It would have been a great play for You Tube. What a bunch of (edit) from these two Verizon call center representatives!
I'm glad Verizon is divesting the Everett call center along with other assets to Frontier, as people like these should not be employed by Verizon, in fact, they should be terminated for cause. Good luck to Frontier with the Everett call center.
Using Verizon's web site when trying to determine what prefixes are in my local calling area (ZUM 1 AND ZUM 2), you are directed to use the following two "very helpful" (my words...lol) links for information...please try for yourselves:
To obtain Local Calling Area information
http://www22.verizon.com/Content/CommonTemplates/sorry.html
Zone Usage Measurement (ZUM) Information
https://www22.verizon.com/ResidentialHelp/Phone/Calling+Plans/Local+And+Regional+Calling+Plans/Gener...
Great Information Verizon!! Both are dead links.
Anyway, point me in the direction where I can obtain the current and accurate prefixes that can be called without charge to ZUM 1 and ZUM 2, and with a charge to ZUM 3 for my exchange and prefixes. DO NOT point me to a white pages directory because that is already outdated (and I do not have a white pages directory).
Again, my exchange is Elsinore Main, and the prefixes are 951-245 and 951-674.
Thank you.
Solved!
Go to Solution.

Home Exchange, Zone 1 and 2 are Local Calling
Zone 3 (ZUM) 13-16 Miles:
PEAK PERIOD RATES: Day 8A-5P   M-F
                          1st Min of Use       Addl Min of Use
                               $.10                          $.04
OFF-PEAK RATE PERIOD: Evening 5P-11P M-F
                               $.07                          $.028
OFF-PEAK RATE PERIOD: Night 11P-8A M-F; SA, SU, & HOLIDAY - All Hours
                               $.04                          $.016
COMMUNITY ---NPA ---NXX ---ZONE -----
ELSINORE ---951 --- 226 245 253 285 471 579 609 674 678 805 --- Home Exch
LAKEVIEW-NUEVO --- 909 --- 251 --- Zone 3
LAKEVIEW-NUEVO --- 951 --- 878 916 928 --- Zone 3
MURRIETA --- 909 ---3 32 --- Zone 2
MURRIETA --- 951 --- 200 219 239 249 304 440 445 461 473 600 671 677 691 696 698 704 813 816 834 837 894 970 973 ---Zone 2
PERRIS --- 909 --- 330 --- Zone 2
PERRIS --- 951 --- 210 229 230 238 259 287 345 378 385 436 442 443 490 550 570 575 581 591 623 657 722 796 940 943 956 --- Zone 2
RANCHO VIEJO --- 949 --- 259 269 284 292 303 326 350 446 480 584 625 702 728 874 --- Zone 3
SUN CITY --- 909 ---508--- Zone 1
SUN CITY --- 951 --- 244 246 301 566 639 672 679 723 746 821 --- Zone 1
TEMECULA --- 909 --- 298 507 668 828 --- Zone 3

LOCAL CALLING AREA FOR HOME PHONE (landline)

Verizon has not resolved my issue with my ability to call ONE of my LOCAL CALLING AREAS. They have passed me NUMEROUS times over and over to many different problems and have not resolved anything. They say they cannot hold on the line while they wait for a supervisor, I keep hearing i will be called back, and do not get any calls back. They "say" they are working with me and a supervisor, and yet still nothing. I contacted the Local Access Transport Area (LATA) and have been told that the numbers I am trying to reach ARE local. Also, I have NEVER had any problems reaching these numbers in the past and ALL OF A SUDDEN 1 out of the 7 local calling areas I cannot call. The local calling area HAS NOT changed and never will according to LATA. One of the reps had the nerve to tell me that another of the "local calling areas" I have is regional, so I had to burst her lil "tell me anything to shut me up" bubble, that she was not gonna feed me that line of **bleep** seeing how I just got off the phone with someone in that area. Verizon seems to be feeding me a lot of **bleep** to try and silence me or so they dont have to try and figure this out. (cause apparently they cant) I have been dealing with this for over a week, many Reps, many repair techs and NOTHING. The repair Techs (automated recording) calls me back and says We cannot find the problem but your line is working properly. ARE YOU KIDDING ME!! DUH! NOW, I have no choice but to contact Consumer Affairs and file a complaint, and I have also been advised to contact the BBB and local television station so that they can run a story. WHAT TO DO NOW!!!

Hi GimmieDps,
I'm sorry you are having difficulty with your calls from home. I have escalated your concern and an agent with access to your account will reach out to you directly by email, private message in the Forums and/or the billing telephone number on your Verizon account for more information or to help you resolve your issue.
Regards,
SunshineF

Long distance in local calling area

I have set up some Skype to go numbers in my calling area and some of them are working but when I dial others Bell Canada says the number is a long distance number. Is there any way to chose the number (ie 613 927 XXXX or 613 434 XXXX) instead of it being automatically assigned? ANy help would be appreciated!

a STG number is mapped to a single target number, and that number must always be entered in international dialing format (i.e. exactly the same way you would dial it if you were wanting to call it using SkypeOut on any Skype client)
Regards,
Neil

Atlantic City, NJ and New York, NY calling area

I have search the Internet for this and have not had any real luck.
What is the local calling area for Atlantic City, NJ and New York, NY, that will not occur long distance charges.
Mainly for Atlantic City, I'm worried about if Ocean City, Wildwood, and Ventnor City are all included or not.
For New York, NY, I just need to know if the whole city local, I would assume, but New York, is setup completely different than most cities I've seen, with 5 boroughs in a city and it being fairly large with multiple area codes.
Also, all this would be the exact same at a Verizon or possibly others payphone as well as just a Verizon landline correct?

Same thing happened to me. It doesn't even matter if you ask explicitly for the weather in NYC.
I asked for the weather in "New York City" and got the results for New York, TX.
I then asked for the weather in "New York City, New York" and got the same results for New York, TX.
Than I asked "What is the weather today in New York City in the state of New York?" and got the weather for New York, TX.
I asked for "Manhattan, New York" and got the weather for TX.
But when I asked for the weather in Brooklyn... I got the weather for Brooklyn, OH.
Pretty impressive.

Are there any apps which will allow local calling using data only that do not require any special numbers called out initially and does not require the receiver to have a similar app or account?

Are there any apps which will allow local calling using data only (not minutes, no extra charge) that do not require any special numbers called out initially and does not require the receiver to have a similar app or account? Just for random local calling.

Yup.
Here is a way you could solve this by adding an extra column and a small lookup table:
The lookup table is here for the copying:
0
1
k
kilo
2
M
mega
3
G
giga
4
T
tera
5
P
peta
6
E
exa
7
Z
zetta
8
Y
yotta
In table 8 (the one on the left in the image) column A is where the values are.
B1=A1÷(1024^VLOOKUP(INT(LOG(A1, 1024)), Binary Prefixes::A:D, 1))&" "&VLOOKUP(INT(LOG(A1, 1024)), Binary Prefixes::A:D, 2)&"B"
this is shorthand for... select cell B1, then type (or copy and paste from here) the formula:
=A1÷(1024^VLOOKUP(INT(LOG(A1, 1024)), Binary Prefixes::A:D, 1))&" "&VLOOKUP(INT(LOG(A1, 1024)), Binary Prefixes::A:D, 2)&"B"
select cell B1, copy,
now select all the cells in column B, paste

Dialing area code for local call - is this normal?

Just had my FIOS triple play installed over the weekend. In the recent past I've used VOIP providers Optimum Voice, Vonage, Packet8, MagicJack and Ooma, and FIOS is the only one that makes me dial my area code to make a local call (I'm in area code 516, where it is not normally necessary to do so).
Is this a bug in the system, and if so, are there any plans to fix it? When I first signed up with Optimum Voice they had a similar problem, but that was 9 years ago!

It is disgraceful that when I signed up for FIOS that I was not informed that I would have to us my area code to call my next door neighbor!!! My realtives that use Fios do not have to do that. They advertise like everything is local buy when I called to complain I'm on the phone with people in Texas who do not even work for Verizon!!! I will be call the Public Service Commission, Better Business Bureau and Consumer Affairs on Monday. The Technical Support people who I waited on hold 15 minutes to speak to were rude and say if I pay more I can have this issue resolved!!! Bait and Switch if I ever heard it!!

Iphone Makes me dial my area code for local calls

For no apparent reason, I started having to dial my area code for local calls manually dialed.
After research/ Found the problem: The culprit in my case was my AT&T Micro Cell tower. All it took was realizing it only did it at home (the location of the towerr) and a lot of trouble shooting with Apple support. They were stumped. The fix was a simple reset of the tower.

It is good practice to always store numbers in contacts with the area code. There is no harm in dialing the area codes even if you live in an area that still uses 7-digit dialing. And, it prevents issues when you travel.

Must dial area code for local calls

A couple of weeks ago, my ability to dial local calls with 7 digits ended. I get a recording saying I must dial the area code. I am in the Albany, NY area (area code 518). No one else has to dial the area code. I tried to call tech support but I have never been able to get through. I tried on-line chat and was told the extra digits were necessary due to the phone service being voip. Now, TimeWarner Cable has voip service and their customers don't dial the area code for local calls. I can't believe this voip answer that I was given. Even my Verizon cell phone allows me to only dial 7 digits.
I like the fios service but the availability of support is terrible. Support that I received from TimeWarner was always good to excellent.
The support reminds me of the old show Laugh In where Lily Tomlin played a telephone company operator and her famous line was "We don't care. We don't have to. We're the phone company."

You can use or not use the 1 before dialing the area code. I have programmed my cell phone and all speed dials to include the area code. If you leave the NY area with your cell and travel outside your home it will tell you that you must dial the area code so i just include the area code on any and all phone numbers nowadays.
When you go to someone elses house using the area code will generally work even though 7 digit dialing may not be required. Just use all 10 numbers to play it safe, same on the cell. This way you get used to using 10 digit dialing.

Local roll area and Roll area

Please refer to following contents from TADM12_2:
1. Virtual Memory includes local memory and shared memory.
2. Local memory is associated with individual work processes.
3. Local work processes memory is for: ABAP load; Data, stack; Buffer for database transfer; Local roll area; Local paging area.
4. The roll file and its associated buffer(also called Roll area).
5. The page file and its associated buffer(also called (SAP) Paging area).
In t-code ST02,
1. the first part is Buffer, all of them belong to shared memory.
2. the second part is SAP Memory, there are four sub-items:
    a)Roll area
    b)Page area
    c)Extended memory --> in shared memory
    d)Heap memory --> in local memory
I am confused whether Roll Area and Page Area here means local Roll/Paging Area in local memory, or Roll/Paging Buffer in shared memory?
Please advise. Thanks
James

Hi James,
Roll Area and page area allocated on local memory, and their buffer areas are allocated on local memory, also. This is because roll and page area are first two block on memory diagram. Those memory areas are dedicated to a work process and start to use when extented memory is filled up. Take a look at "http://help.sap.com/saphelp_nw70/helpdata/EN/28/d1d3f6bcb411d188b30000e83539c3/frameset.htm" for the memory diagram on SAP
Best regards,
Orkun Gedik

Issue with SPA525g registation and FXO port call calls are not disconnecting properly

Hi,
I have a UC540 and updated it to the latest IOS version with the latest firmware to my phones and i am having registration problems with SPA525g IP Phones. I updated the firmware of the phones as well and create manual tftp bindings with but still it is not registering. I run a couple of debugs (debug tftp events and debug ephone registration) I can see from the logs and in the phone that it is taking the proper VLAN and being discovered via CDP and being pointed to the TFTP server and still wont register. I can see that it is also taking its own .cnf file properly then the output sccp token regected invalid devices error is shown I have a SPA502G and it is working fine. Also there is a previous issue that all the voice port are shown as engage or offhook even the calls are disconnected thus make the main PSTN number busy am based in UAE and our service provider is etisalat I have check with them about the proper disconnection values but still it the same. That's why I have arrived in the conclusion to just update everything including the IOS and the phones firmware. I have put my config in this post, I am also trying to take the CCNA Voice exam on the 2nd week of april and I think that if i don't know how fix this issue for our customer then I would probably fail that exam. any suggestion and help is greatly appreciated cisco experts.
! Last configuration change at 13:36:42 ZP4 Thu Sep 13 2012 by Nick
! NVRAM config last updated at 13:45:41 ZP4 Thu Sep 13 2012 by Nick
version 15.1
parser config cache interface
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service internal
service compress-config
service sequence-numbers
hostname UC540
boot-start-marker
boot system flash:uc500-advipservicesk9-mz.151-2.T4
boot-end-marker
logging buffered 64000
enable secret 5 $1$3CIf$.rXyHeJQrwd97X/f2dS0M1
no aaa new-model
clock timezone ZP4 4 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-3558175224
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3558175224
revocation-check none
crypto pki certificate chain TP-self-signed-3558175224
certificate self-signed 01 nvram:IOS-Self-Sig#3.cer
dot11 syslog
dot11 ssid cisco-data
vlan 1
authentication open
dot11 ssid cisco-voice
vlan 100
authentication open
ip source-route
ip cef
ip dhcp relay information trust-all
ip dhcp excluded-address 10.1.3.1 10.1.3.10
ip dhcp pool phone
   network 10.1.3.0 255.255.255.0
   default-router 10.1.3.1
   option 150 ip 10.1.3.1
ip name-server 213.42.20.20
ip name-server 195.229.241.222
ip inspect WAAS flush-timeout 10
ip inspect name SDM_LOW cuseeme
ip inspect name SDM_LOW dns
ip inspect name SDM_LOW ftp
ip inspect name SDM_LOW h323
ip inspect name SDM_LOW https
ip inspect name SDM_LOW icmp
ip inspect name SDM_LOW imap
ip inspect name SDM_LOW pop3
ip inspect name SDM_LOW netshow
ip inspect name SDM_LOW rcmd
ip inspect name SDM_LOW realaudio
ip inspect name SDM_LOW rtsp
ip inspect name SDM_LOW esmtp
ip inspect name SDM_LOW sqlnet
ip inspect name SDM_LOW streamworks
ip inspect name SDM_LOW tftp
ip inspect name SDM_LOW tcp router-traffic
ip inspect name SDM_LOW udp router-traffic
ip inspect name SDM_LOW vdolive
no ipv6 cef
multilink bundle-name authenticated
stcapp ccm-group 1
stcapp
stcapp supplementary-services
port 0/0/0
fallback-dn 301
port 0/0/1
fallback-dn 302
port 0/0/2
fallback-dn 303
port 0/0/3
fallback-dn 304
trunk group ALL_FXO
max-retry 5
voice-class cause-code 1
hunt-scheme longest-idle
translation-profile outgoing PROFILE_ALL_FXO
trunk group ALL_FX0
voice call send-alert
voice rtp send-recv
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
sip
no update-callerid
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g711ulaw
voice class dualtone-detect-params 1
freq-max-deviation 50
freq-max-power 0
freq-min-power 13
freq-power-twist 4
cadence-variation 6
voice class custom-cptone UAE-CUSTOM
dualtone disconnect
frequency 406
cadence 398 344 237 527 400
voice class custom-cptone CCAjointone
dualtone conference
frequency 600 900
cadence 300 150 300 100 300 50
voice class custom-cptone CCAleavetone
dualtone conference
frequency 400 800
cadence 400 50 200 50 200 50
voice class cause-code 1
no-circuit
voice register global
voice hunt-group 1 parallel
list 301,302,303
timeout 24
pilot 511
voice translation-rule 4
rule 15 // //
voice translation-rule 1000
rule 1 /.*/ //
voice translation-rule 1111
voice translation-rule 1112
rule 1 /^9/ //
rule 3 /^0/ //
voice translation-rule 2222
voice translation-rule 3265
rule 1 /$^..........$$/ /9\1/
rule 2 /$^.........$$/ /9\1/
rule 15 /$^ABCD$$/ /ABCD\1/
voice translation-profile CALLER_ID_TRANSLATION_PROFILE
translate calling 1111
voice translation-profile CallBlocking
translate called 2222
voice translation-profile INCOMING_CallerID_PROFILE
translate calling 3265
voice translation-profile OUTGOING_TRANSLATION_PROFILE
translate called 1112
voice translation-profile PROFILE_ALL_FXO
translate calling 4
voice translation-profile nondialable
translate called 1000
voice-card 0
dspfarm
dsp services dspfarm
license udi pid UC540W-FXO-K9 sn FHK143074G6
archive
log config
logging enable
logging size 600
hidekeys
username cisco privilege 15 secret 5 $1$vjNa$OFKLhupqR8al6x2b8Xmcj/
username adminac privilege 15 secret 5 $1$NDC.$PtD0y4YGIj5SqI1gghxWE1
username Nick privilege 15 secret 5 $1$iAmL$tsg7Jf2TEND1NN.h8z2dy/
ip tftp source-interface Loopback0
bridge irb
interface Loopback0
description $FW_INSIDE$
ip address 10.1.10.2 255.255.255.252
ip access-group 101 in
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/0
description $FW_OUTSIDE$
ip address 192.168.101.2 255.255.255.252
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface Integrated-Service-Engine0/0
description cue is initialized with default IMAP group
ip unnumbered Loopback0
ip nat inside
ip virtual-reassembly in
service-module ip address 10.1.10.1 255.255.255.252
service-module ip default-gateway 10.1.10.2
interface FastEthernet0/1/0
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/1
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/2
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/3
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/4
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/5
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/6
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/7
switchport access vlan 20
spanning-tree portfast
interface FastEthernet0/1/8
switchport access vlan 100
macro description cisco-switch
interface Dot11Radio0/5/0
no ip address
shutdown
ssid cisco-data
ssid cisco-voice
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
interface Dot11Radio0/5/0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0/5/0.100
encapsulation dot1Q 100
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 spanning-disabled
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
interface Vlan1
no ip address
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan20
ip address 10.10.10.1 255.255.255.0
interface Vlan100
no ip address
bridge-group 100
bridge-group 100 spanning-disabled
interface BVI1
description $FW_INSIDE$
no ip address
ip nat inside
ip virtual-reassembly in
shutdown
interface BVI100
description $FW_INSIDE$
ip address 10.1.3.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http path flash:/gui
ip dns server
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 192.168.101.1
ip route 10.1.10.1 255.255.255.255 Integrated-Service-Engine0/0
logging esm config
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 192.168.10.0 0.0.0.255
access-list 1 permit 10.1.3.0 0.0.0.255
access-list 1 permit 10.1.10.0 0.0.0.3
access-list 100 remark auto generated by SDM firewall configuration
access-list 100 remark SDM_ACL Category=1
access-list 100 deny   ip 192.168.10.0 0.0.0.255 any
access-list 100 deny   ip host 255.255.255.255 any
access-list 100 deny   ip 127.0.0.0 0.255.255.255 any
access-list 100 permit ip any any
access-list 101 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 101 remark SDM_ACL Category=1
access-list 101 permit tcp 10.1.3.0 0.0.0.255 eq 2000 any
access-list 101 permit udp 10.1.3.0 0.0.0.255 eq 2000 any
access-list 101 deny   ip 10.1.3.0 0.0.0.255 any
access-list 101 deny   ip 192.168.10.0 0.0.0.255 any
access-list 101 deny   ip 192.168.101.0 0.0.0.3 any
access-list 101 deny   ip host 255.255.255.255 any
access-list 101 deny   ip 127.0.0.0 0.255.255.255 any
access-list 101 permit ip any any
access-list 102 remark auto generated by SDM firewall configuration##NO_ACES_6##
access-list 102 remark SDM_ACL Category=1
access-list 102 deny   ip 10.1.10.0 0.0.0.3 any
access-list 102 deny   ip 10.1.3.0 0.0.0.255 any
access-list 102 deny   ip 192.168.101.0 0.0.0.3 any
access-list 102 deny   ip host 255.255.255.255 any
access-list 102 deny   ip 127.0.0.0 0.255.255.255 any
access-list 102 permit ip any any
access-list 102 permit ip 192.168.101.0 0.0.0.3 any
access-list 103 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 103 remark SDM_ACL Category=1
access-list 103 permit tcp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 permit udp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 deny   ip 10.1.10.0 0.0.0.3 any
access-list 103 deny   ip 192.168.10.0 0.0.0.255 any
access-list 103 deny   ip 192.168.101.0 0.0.0.3 any
access-list 103 deny   ip host 255.255.255.255 any
access-list 103 deny   ip 127.0.0.0 0.255.255.255 any
access-list 103 permit ip any any
access-list 105 permit ip any any
snmp-server community public RO
tftp-server flash:/phones/521_524/cp524g-8-1-17.bin alias cp524g-8-1-17.bin
tftp-server flash:/phones/5x5/spa5x5-7-1-3c.bin alias spa5x5-7-1-3c.bin
tftp-server flash:/phones/525/spa525g-7-4-8.bin alias spa525g-7-4-8.bin
control-plane
bridge 1 route ip
bridge 100 route ip
voice-port 0/0/0
cptone GB
station-id name Cordless
station-id number 329
caller-id enable
voice-port 0/0/1
cptone AE
caller-id enable
voice-port 0/0/2
cptone AE
caller-id enable
voice-port 0/0/3
cptone AE
caller-id enable
voice-port 0/1/0
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4FXO-0/1/0-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/1
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/1-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/2
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
supervisory dualtone-detect-params 1
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/2-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/3
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/3-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/4/0
auto-cut-through
signal immediate
input gain auto-control -15
description Music On Hold Port
sccp local Loopback0
sccp ccm 10.1.3.1 identifier 1 version 4.0
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate profile 1 register confprof1
dspfarm profile 1 conference
description DO NOT MODIFY, active CCA conference profile - CCA2.0 codec729
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dial-peer cor custom
name internal
name local
name local-plus
name international
name national
name national-plus
name emergency
name toll-free
dial-peer cor list call-internal
member internal
dial-peer cor list call-local
member local
dial-peer cor list call-local-plus
member local-plus
dial-peer cor list call-national
member national
dial-peer cor list call-national-plus
member national-plus
dial-peer cor list call-international
member international
dial-peer cor list call-emergency
member emergency
dial-peer cor list call-toll-free
member toll-free
dial-peer cor list user-internal
member internal
member emergency
dial-peer cor list user-local
member internal
member local
member emergency
member toll-free
dial-peer cor list user-local-plus
member internal
member local
member local-plus
member emergency
member toll-free
dial-peer cor list user-national
member internal
member local
member local-plus
member national
member emergency
member toll-free
dial-peer cor list user-national-plus
member internal
member local
member local-plus
member national
member national-plus
member emergency
member toll-free
dial-peer cor list user-international
member internal
member local
member local-plus
member international
member national
member national-plus
member emergency
member toll-free
dial-peer voice 1 pots
port 0/0/0
no sip-register
dial-peer voice 2 pots
port 0/0/1
no sip-register
dial-peer voice 3 pots
port 0/0/2
no sip-register
dial-peer voice 4 pots
port 0/0/3
no sip-register
dial-peer voice 5 pots
description ** MOH Port **
destination-pattern ABC
port 0/4/0
no sip-register
dial-peer voice 50 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/0
dial-peer voice 51 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/1
dial-peer voice 52 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/2
dial-peer voice 53 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/3
dial-peer voice 54 pots
description ** FXO pots dial-peer **
destination-pattern A0
port 0/1/0
no sip-register
dial-peer voice 55 pots
description ** FXO pots dial-peer **
destination-pattern A1
port 0/1/1
no sip-register
dial-peer voice 56 pots
description ** FXO pots dial-peer **
destination-pattern A2
port 0/1/2
no sip-register
dial-peer voice 2000 voip
description ** cue voicemail pilot number **
destination-pattern 388
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 6 pots
description "catch all dial peer for BRI/PRI"
translation-profile incoming nondialable
incoming called-number .%
direct-inward-dial
dial-peer voice 57 pots
description ** FXO pots dial-peer **
destination-pattern A3
port 0/1/3
no sip-register
dial-peer voice 69 pots
destination-pattern 329
port 0/0/0
dial-peer voice 300 pots
trunkgroup ALL_FX0
description Local Numbers
destination-pattern 9T
forward-digits 9
dial-peer voice 301 voip
destination-pattern 2..
session target ipv4:192.168.201.2
dial-peer voice 303 pots
trunkgroup ALL_FXO
trunkgroup ALL_FX0
description **InternationalCall**
destination-pattern 88T
dial-peer voice 304 pots
trunkgroup ALL_FX0
description *EM1*
destination-pattern 9[1-9]T
forward-digits 3
dial-peer voice 302 pots
trunkgroup ALL_FX0
description **Mobiles**
destination-pattern 9.[0-9].[0-9]......
dial-peer voice 305 pots
trunkgroup ALL_FX0
description **800-**
destination-pattern 9[0-9][0-9][0-9]T
no dial-peer outbound status-check pots
telephony-service
sdspfarm conference mute-on 111 mute-off 222
sdspfarm units 5
sdspfarm tag 1 confprof1
conference hardware
video
fxo hook-flash
max-ephones 40
max-dn 300
ip source-address 10.1.3.1 port 2000
max-redirect 20
auto assign 1 to 1 type bri
calling-number initiator
service phone videoCapability 1
service phone webAccess 0
service dnis overlay
service dnis dir-lookup
timeouts interdigit 5
system message American Center
url services http://10.1.10.1/voiceview/common/login.do
url authentication http://10.1.10.2/CCMCIP/authenticate.asp
load 521G-524G cp524g-8-1-17
load 525G spa525g-7-4-8
load 501G spa5x5-7-1-3c
load 502G spa5x5-7-1-3c
load 504G spa5x5-7-1-3c
load 508G spa5x5-7-1-3c
load 509G spa5x5-7-1-3c
time-zone 35
date-format dd-mm-yy
voicemail 388
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
hunt-group logout HLog
moh MOH2.wav
multicast moh 239.10.16.16 port 2000
web admin system name cisco secret 5 $1$iDgA$MKNi2RWfsO0KjuC82kgLJ1
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern 9.T
transfer-pattern .T
secondary-dialtone 9
fac standard
create cnf-files version-stamp 7960 Aug 29 2012 12:00:04
line con 0
privilege level 15
logging synchronous
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
exec-timeout 0 0
logging synchronous
login local
transport input all
line vty 5 100
login local
transport input all
ntp master
end
Some of the output are not shown becaus it is to long I have attach the whole config for reference and any advice on how could I optimize and resolve my issues is greatly appreciated. Thanks

Nicolo - First off this stuff gets crazy sometimes. No worries about the exam. Sometimes when FXO ports go crazy it is due to battery reversal. If you go to the FXO port settings try turning battery reversal on and or off... depending on its current setting. See if that helps.
As for the 525s not registering.. These are inside the network correct? Are you connecting one directly to the UC500 with a Cat5E or Cat6 patch cable and the same thing happens? Does the MAC address on the phone match a MAC address under the EPHONE settings?
If you telnet into the UC500 can you execute a "dir" command at the CLI prompt and "CD" (change directory) into the phones folder and then the spa525g folder? Do files exist in there?
Also I only see an IP address under BVI100? This is the voice side of things what happened to the IP address under BVI1 (Data VLAN). Can you give us some information about the internal network? Cna you PING this phone system from the network? What IP address does it have?

Proxy calls are not permitted on IS

Hello,
I have implemented a scenerio between SAP AR -
XI --- SAP FCSM.
Now SAP and Xi are on same server but clients are different.
For SAP client is 110 for XI client is 100.
In sxmb_adm we have set SAP as application server and Xi as IS.
While testing this secerio i got a error as Proxy calls are not permitted on sender or receiver side on the IS (client)
If i check in sxmb_moni i found 2 messages one is sucessful and other one with error shown above.
can anyone help me out in this.
regards,
Vikrant

Hi Vikrant,
Need to be configure the Business Systems as the Local Integration Engine
In the respective application client, choose Exchange Infrastructure -> Administration -> Integration Engine u2013 Administration (SXMB_ADM) in the user menu.
2.Choose Integration Engine Configuration.
3. In the menu bar, choose Edit -> Change Global Configuration Data.
4.In the Global Configuration Data frame, choose Application System as the role of the business system.
5.In the Corresponding Integ. Server field, specify the HTTP destination that the business system uses to address the central Integration Server. Use the following syntax: dest://<HTTP Destination>
Specify the HTTP destination of the Integration Server that you created during the technical configuration of SAP Exchange Infrastructure.
regards
Ashwin
Edited by: ashwin dhakne on Mar 6, 2009 5:26 PM

How can use EJB local call in WLS 7.0 without EAR

I have web application as jsp files.
and I made .jar for some EJBs
and I used local call for calling EJB from jsps in WLS 6.1
but in WLS 7.0 .. occured error calling EJB as Local call
while JNDI lookup.
So I packed all applications as EAR and deployed then all works good.
but in developing I want to use JSPs as jsp files.
There is no way to use Local call to EJB in WLS 7.0 without packing EAR ? (like
WLS 6.1)

The way JNDI lookups were implemented in 6.1 allowed to deploy individual ejb-jars
and access their local interfaces via JNDI lookups from other ejb-jars during
development. In production all ejb-jars will be packaged into an ear.
This is extremely helpful on large projects. E.g. my current project has over
120 CMP entity beans and over 40 session beans. Even on 2GHz class machine with
1Gb memory and JDK 1.4 (to enable full-speed debugging) it takes almost a minute
to deploy the ear (no matter whether it is exploded or not). It takes minutes
with 1.3 and debugging turned on.
6.1 implementation allowed to "pre-deploy" relatively static ejb-jars and still
access their local interfaces (by putting them on WL system classpath and deploying
as individual ejb-jars, so classes are accessible to local clients; it requires
WL restart when they are changed, but they don't change often). So during development
only changed jars (typically session facade) need to be redeployed on changes,
which takes only seconds. We didn't have problem with JNDI lookup performance
since we use the EJBHomeFactory pattern.
The behind-the-scene JNDI optimization "improvement" introduced in 7.0 makes it
no longer possible to use this technique, since even though classloading still
works in the same way, no objects are bound to JNDI tree and thus could not be
access from another ejb-jar. This significantly impacts developer productivity
(in our large project). It's not only about minutes lost (which btw makes hours
over time), it just disrupts developer's train of thought to have such long round
trip times. In fact this is the reason we are not going to migrate to WL 7.0.
Is it possible to provide an option to turn this "optimization" off and actually
bind JNDI objects?
Thank you,
Sergey
"Dimitri I. Rakitine" <[email protected]> wrote:
Park <[email protected]> wrote:
Thanks Rakitine.
I wonder if I use EAR while developing could I apply changes to EARwhithout packing
again.Sure - you can simply deploy your app as an 'exploded' EAR during development.
There is no probelm delivering time but in developing time ..
If I can not use that kind of way how can I make modification ?
Plz. let me know.
And I have one more question.
When I use EAR I met some problem.
I packed all JSP into one .war file.
fot that I had to inclde requred classes into .war because jsps usethese classes.
then I packed EAR file with WAR and some EJB jar files.
After then I deployed EAR file to WLS.
But If remove classes from classpth while EJB deploying Error occured.Because
EJBs reference these classes.
I thoght if I packed classes into .WAR .. there is no problem.
But Error occured.
I have to include classes into classpth for that ? or
Any mistakes in my way.No, you do not have to add anything to the system classpath. In fact,
you should
make sure that none of your application classes are in the system classpath.
thank you.
"Dimitri I. Rakitine" <[email protected]> wrote:
Yup, that appears to be the difference between 6.1 and 7.0 - in
6.1 success of a local invocation depended only on the Classloaders
arrangement, so everything worked when you added your classes to the
system classpath. In 7.0 looks like it also depends on the application
context - that's why you cannot do a JNDI lookup from another deployment
unit.
Is there any reason why you do not want to use EAR's ???
Park <[email protected]> wrote:
in WLS 6.1 ..
I have EJB as jar files. (deployed each to WLS)
and I added EJB interface class to classpath.
and I made WebApplication as Directory (not war file).
in that webappication jsp call EJB as Local interface.
These environment .. local call workes well in WLS 6.1.
but in 7.1 not works .. (JNDI look up error)
of course Remote call works well. and If I make EAR .. works well.
Rob Woollen <[email protected]> wrote:
You can have an exploded EAR and have it work.
Can you give some more detail on how you are deploying in 6.1. Is
it
an
exploded EAR, or do you have the ejb interfaces in the classpath?
This behavior should not have changed between 6.1 and 7.0.
-- Rob
park wrote:
I have web application as jsp files.
and I made .jar for some EJBs
and I used local call for calling EJB from jsps in WLS 6.1
but in WLS 7.0 .. occured error calling EJB as Local call
while JNDI lookup.
So I packed all applications as EAR and deployed then all works
good.
but in developing I want to use JSPs as jsp files.
There is no way to use Local call to EJB in WLS 7.0 without packingEAR ? (like
WLS 6.1)
Dimitri
Dimitri

Local calling when CCM is in another state

My CallManager cluster is in my office, and I'm trying to set up some phones in another office in another state over a WAN link. The phones are going to register with my gateway in my office, but the users in the remote office want to be able to dial local calls in that state. Has anyone set up something like this? I'm assuming I would need to set up a separate partition and CSS and route the local calls over our long distance trunks, but I don't know how to make this seamless to the end user. Thanks.

you're on the right track, what you're trying to do is very common. toll bypass is the name of this, the way you need to configure it is to have a route pattern for the phones at the remote location that will use the local gateway to route the calls, if the main site will use the PSTN to route the calls and a local GW users from that site should reach another route pattern which uses the local GW
if you mean users want to do 7 digit dialing while you need 10 digits to route the call, all you need to do is create a route pattern for remote users and use the called party transformation mask to add the 3 digits or use the prefix field to add the digits
HTH

Local Calling Area

Similar Messages

Maybe you are looking for